arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
index b0f2c56..dbd6d53 100644
--- a/include/linux/platform_data/atmel.h
+++ b/include/linux/platform_data/atmel.h
@@ -8,6 +8,49 @@
#define __ATMEL_H__
#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
+#include <sound/atmel-ac97c.h>
+#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
+
+ /* USB Device */
+struct at91_udc_data {
+ int vbus_pin; /* high == host powering us */
+ u8 vbus_active_low; /* vbus polarity */
+ u8 vbus_polled; /* Use polling, not interrupt */
+ int pullup_pin; /* active == D+ pulled up */
+ u8 pullup_active_low; /* true == pullup_pin is active low */
+};
+
+ /* Compact Flash */
+struct at91_cf_data {
+ int irq_pin; /* I/O IRQ */
+ int det_pin; /* Card detect */
+ int vcc_pin; /* power switching */
+ int rst_pin; /* card reset */
+ u8 chipselect; /* EBI Chip Select number */
+ u8 flags;
+#define AT91_CF_TRUE_IDE 0x01
+#define AT91_IDE_SWAP_A0_A2 0x02
+};
+
+ /* USB Host */
+#define AT91_MAX_USBH_PORTS 3
+struct at91_usbh_data {
+ int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */
+ int overcurrent_pin[AT91_MAX_USBH_PORTS];
+ u8 ports; /* number of ports on root hub */
+ u8 overcurrent_supported;
+ u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+ u8 overcurrent_status[AT91_MAX_USBH_PORTS];
+ u8 overcurrent_changed[AT91_MAX_USBH_PORTS];
+};
/* NAND / SmartMedia */
struct atmel_nand_data {
@@ -24,4 +67,28 @@
unsigned int num_parts;
};
+ /* Serial */
+struct atmel_uart_data {
+ int num; /* port num */
+ short use_dma_tx; /* use transmit DMA? */
+ short use_dma_rx; /* use receive DMA? */
+ void __iomem *regs; /* virt. base address, if any */
+ struct serial_rs485 rs485; /* rs485 settings */
+};
+
+ /* Touchscreen Controller */
+struct at91_tsadcc_data {
+ unsigned int adc_clock;
+ u8 pendet_debounce;
+ u8 ts_sample_hold_time;
+};
+
+/* CAN */
+struct at91_can_data {
+ void (*transceiver_switch)(int on);
+};
+
+/* FIXME: this needs a better location, but gets stuff building again */
+extern int at91_suspend_entering_slow_clock(void);
+
#endif /* __ATMEL_H__ */