Merge branch 'ingenic' into devel
diff --git a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
new file mode 100644
index 0000000..7988aeb
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
@@ -0,0 +1,46 @@
+Ingenic jz47xx GPIO controller
+
+That the Ingenic GPIO driver node must be a sub-node of the Ingenic pinctrl
+driver node.
+
+Required properties:
+--------------------
+
+ - compatible: Must contain one of:
+ - "ingenic,jz4740-gpio"
+ - "ingenic,jz4770-gpio"
+ - "ingenic,jz4780-gpio"
+ - reg: The GPIO bank number.
+ - interrupt-controller: Marks the device node as an interrupt controller.
+ - interrupts: Interrupt specifier for the controllers interrupt.
+ - #interrupt-cells: Should be 2. Refer to
+ ../interrupt-controller/interrupts.txt for more details.
+ - gpio-controller: Marks the device node as a GPIO controller.
+ - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+ cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+ GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+ - gpio-ranges: Range of pins managed by the GPIO controller. Refer to
+ 'gpio.txt' in this directory for more details.
+
+Example:
+--------
+
+&pinctrl {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,jz4740-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <28>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
new file mode 100644
index 0000000..ca313a7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
@@ -0,0 +1,41 @@
+Ingenic jz47xx pin controller
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+For the jz47xx SoCs, pin control is tightly bound with GPIO ports. All pins may
+be used as GPIOs, multiplexed device functions are configured within the
+GPIO port configuration registers and it is typical to refer to pins using the
+naming scheme "PxN" where x is a character identifying the GPIO port with
+which the pin is associated and N is an integer from 0 to 31 identifying the
+pin within that GPIO port. For example PA0 is the first pin in GPIO port A, and
+PB31 is the last pin in GPIO port B. The jz4740 contains 4 GPIO ports, PA to
+PD, for a total of 128 pins. The jz4780 contains 6 GPIO ports, PA to PF, for a
+total of 192 pins.
+
+
+Required properties:
+--------------------
+
+ - compatible: One of:
+ - "ingenic,jz4740-pinctrl"
+ - "ingenic,jz4770-pinctrl"
+ - "ingenic,jz4780-pinctrl"
+ - reg: Address range of the pinctrl registers.
+
+
+GPIO sub-nodes
+--------------
+
+The pinctrl node can have optional sub-nodes for the Ingenic GPIO driver;
+please refer to ../gpio/ingenic,gpio.txt.
+
+
+Example:
+--------
+
+pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,jz4740-pinctrl";
+ reg = <0x10010000 0x400>;
+};
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 2828ecd..45bcd1c 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -364,6 +364,7 @@
select SYS_SUPPORTS_ZBOOT_UART16550
select DMA_NONCOHERENT
select IRQ_MIPS_CPU
+ select PINCTRL
select GPIOLIB
select COMMON_CLK
select GENERIC_IRQ_CHIP
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 1652d8d..fd138d99 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -29,18 +29,30 @@
&uart0 {
status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart0>;
};
&uart1 {
status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart1>;
};
&uart3 {
status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart2>;
};
&uart4 {
status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart4>;
};
&nemc {
@@ -61,6 +73,13 @@
ingenic,nemc-tAW = <15>;
ingenic,nemc-tSTRV = <100>;
+ /*
+ * Only CLE/ALE are needed for the devices that are connected, rather
+ * than the full address line set.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_nemc>;
+
nand@1 {
reg = <1>;
@@ -69,6 +88,9 @@
nand-ecc-mode = "hw";
nand-on-flash-bbt;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_nemc_cs1>;
+
partitions {
compatible = "fixed-partitions";
#address-cells = <2>;
@@ -106,3 +128,41 @@
&bch {
status = "okay";
};
+
+&pinctrl {
+ pins_uart0: uart0 {
+ function = "uart0";
+ groups = "uart0-data";
+ bias-disable;
+ };
+
+ pins_uart1: uart1 {
+ function = "uart1";
+ groups = "uart1-data";
+ bias-disable;
+ };
+
+ pins_uart2: uart2 {
+ function = "uart2";
+ groups = "uart2-data", "uart2-hwflow";
+ bias-disable;
+ };
+
+ pins_uart4: uart4 {
+ function = "uart4";
+ groups = "uart4-data";
+ bias-disable;
+ };
+
+ pins_nemc: nemc {
+ function = "nemc";
+ groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
+ bias-disable;
+ };
+
+ pins_nemc_cs1: nemc-cs1 {
+ function = "nemc-cs1";
+ groups = "nemc-cs1";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4740.dtsi b/arch/mips/boot/dts/ingenic/jz4740.dtsi
index 3e1587f..2ca7ce7 100644
--- a/arch/mips/boot/dts/ingenic/jz4740.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4740.dtsi
@@ -55,6 +55,74 @@
clock-names = "rtc";
};
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,jz4740-pinctrl";
+ reg = <0x10010000 0x400>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,jz4740-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <28>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,jz4740-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,jz4740-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <26>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,jz4740-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <25>;
+ };
+ };
+
uart0: serial@10030000 {
compatible = "ingenic,jz4740-uart";
reg = <0x10030000 0x100>;
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index b868b42..4853ef6 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -44,6 +44,104 @@
#clock-cells = <1>;
};
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,jz4780-pinctrl";
+ reg = <0x10010000 0x600>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+
+ gpe: gpio@4 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <4>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 128 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <13>;
+ };
+
+ gpf: gpio@5 {
+ compatible = "ingenic,jz4780-gpio";
+ reg = <5>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 160 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <12>;
+ };
+ };
+
uart0: serial@10030000 {
compatible = "ingenic,jz4780-uart";
reg = <0x10030000 0x100>;
diff --git a/arch/mips/boot/dts/ingenic/qi_lb60.dts b/arch/mips/boot/dts/ingenic/qi_lb60.dts
index be1a7d3..b715ee2 100644
--- a/arch/mips/boot/dts/ingenic/qi_lb60.dts
+++ b/arch/mips/boot/dts/ingenic/qi_lb60.dts
@@ -17,3 +17,16 @@
&rtc_dev {
system-power-controller;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart0>;
+};
+
+&pinctrl {
+ pins_uart0: uart0 {
+ function = "uart0";
+ groups = "uart0-data";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/include/asm/mach-jz4740/gpio.h b/arch/mips/include/asm/mach-jz4740/gpio.h
index 7c7708a..fd847c9 100644
--- a/arch/mips/include/asm/mach-jz4740/gpio.h
+++ b/arch/mips/include/asm/mach-jz4740/gpio.h
@@ -16,380 +16,9 @@
#ifndef _JZ_GPIO_H
#define _JZ_GPIO_H
-#include <linux/types.h>
-
-enum jz_gpio_function {
- JZ_GPIO_FUNC_NONE,
- JZ_GPIO_FUNC1,
- JZ_GPIO_FUNC2,
- JZ_GPIO_FUNC3,
-};
-
-/*
- Usually a driver for a SoC component has to request several gpio pins and
- configure them as function pins.
- jz_gpio_bulk_request can be used to ease this process.
- Usually one would do something like:
-
- static const struct jz_gpio_bulk_request i2c_pins[] = {
- JZ_GPIO_BULK_PIN(I2C_SDA),
- JZ_GPIO_BULK_PIN(I2C_SCK),
- };
-
- inside the probe function:
-
- ret = jz_gpio_bulk_request(i2c_pins, ARRAY_SIZE(i2c_pins));
- if (ret) {
- ...
-
- inside the remove function:
-
- jz_gpio_bulk_free(i2c_pins, ARRAY_SIZE(i2c_pins));
-
-*/
-
-struct jz_gpio_bulk_request {
- int gpio;
- const char *name;
- enum jz_gpio_function function;
-};
-
-#define JZ_GPIO_BULK_PIN(pin) { \
- .gpio = JZ_GPIO_ ## pin, \
- .name = #pin, \
- .function = JZ_GPIO_FUNC_ ## pin \
-}
-
-int jz_gpio_bulk_request(const struct jz_gpio_bulk_request *request, size_t num);
-void jz_gpio_bulk_free(const struct jz_gpio_bulk_request *request, size_t num);
-void jz_gpio_bulk_suspend(const struct jz_gpio_bulk_request *request, size_t num);
-void jz_gpio_bulk_resume(const struct jz_gpio_bulk_request *request, size_t num);
-void jz_gpio_enable_pullup(unsigned gpio);
-void jz_gpio_disable_pullup(unsigned gpio);
-int jz_gpio_set_function(int gpio, enum jz_gpio_function function);
-
-int jz_gpio_port_direction_input(int port, uint32_t mask);
-int jz_gpio_port_direction_output(int port, uint32_t mask);
-void jz_gpio_port_set_value(int port, uint32_t value, uint32_t mask);
-uint32_t jz_gpio_port_get_value(int port, uint32_t mask);
-
#define JZ_GPIO_PORTA(x) ((x) + 32 * 0)
#define JZ_GPIO_PORTB(x) ((x) + 32 * 1)
#define JZ_GPIO_PORTC(x) ((x) + 32 * 2)
#define JZ_GPIO_PORTD(x) ((x) + 32 * 3)
-/* Port A function pins */
-#define JZ_GPIO_MEM_DATA0 JZ_GPIO_PORTA(0)
-#define JZ_GPIO_MEM_DATA1 JZ_GPIO_PORTA(1)
-#define JZ_GPIO_MEM_DATA2 JZ_GPIO_PORTA(2)
-#define JZ_GPIO_MEM_DATA3 JZ_GPIO_PORTA(3)
-#define JZ_GPIO_MEM_DATA4 JZ_GPIO_PORTA(4)
-#define JZ_GPIO_MEM_DATA5 JZ_GPIO_PORTA(5)
-#define JZ_GPIO_MEM_DATA6 JZ_GPIO_PORTA(6)
-#define JZ_GPIO_MEM_DATA7 JZ_GPIO_PORTA(7)
-#define JZ_GPIO_MEM_DATA8 JZ_GPIO_PORTA(8)
-#define JZ_GPIO_MEM_DATA9 JZ_GPIO_PORTA(9)
-#define JZ_GPIO_MEM_DATA10 JZ_GPIO_PORTA(10)
-#define JZ_GPIO_MEM_DATA11 JZ_GPIO_PORTA(11)
-#define JZ_GPIO_MEM_DATA12 JZ_GPIO_PORTA(12)
-#define JZ_GPIO_MEM_DATA13 JZ_GPIO_PORTA(13)
-#define JZ_GPIO_MEM_DATA14 JZ_GPIO_PORTA(14)
-#define JZ_GPIO_MEM_DATA15 JZ_GPIO_PORTA(15)
-#define JZ_GPIO_MEM_DATA16 JZ_GPIO_PORTA(16)
-#define JZ_GPIO_MEM_DATA17 JZ_GPIO_PORTA(17)
-#define JZ_GPIO_MEM_DATA18 JZ_GPIO_PORTA(18)
-#define JZ_GPIO_MEM_DATA19 JZ_GPIO_PORTA(19)
-#define JZ_GPIO_MEM_DATA20 JZ_GPIO_PORTA(20)
-#define JZ_GPIO_MEM_DATA21 JZ_GPIO_PORTA(21)
-#define JZ_GPIO_MEM_DATA22 JZ_GPIO_PORTA(22)
-#define JZ_GPIO_MEM_DATA23 JZ_GPIO_PORTA(23)
-#define JZ_GPIO_MEM_DATA24 JZ_GPIO_PORTA(24)
-#define JZ_GPIO_MEM_DATA25 JZ_GPIO_PORTA(25)
-#define JZ_GPIO_MEM_DATA26 JZ_GPIO_PORTA(26)
-#define JZ_GPIO_MEM_DATA27 JZ_GPIO_PORTA(27)
-#define JZ_GPIO_MEM_DATA28 JZ_GPIO_PORTA(28)
-#define JZ_GPIO_MEM_DATA29 JZ_GPIO_PORTA(29)
-#define JZ_GPIO_MEM_DATA30 JZ_GPIO_PORTA(30)
-#define JZ_GPIO_MEM_DATA31 JZ_GPIO_PORTA(31)
-
-#define JZ_GPIO_FUNC_MEM_DATA0 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA1 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA2 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA3 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA4 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA5 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA6 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA7 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA8 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA9 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA10 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA11 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA12 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA13 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA14 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA15 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA16 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA17 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA18 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA19 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA20 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA21 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA22 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA23 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA24 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA25 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA26 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA27 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA28 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA29 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA30 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DATA31 JZ_GPIO_FUNC1
-
-/* Port B function pins */
-#define JZ_GPIO_MEM_ADDR0 JZ_GPIO_PORTB(0)
-#define JZ_GPIO_MEM_ADDR1 JZ_GPIO_PORTB(1)
-#define JZ_GPIO_MEM_ADDR2 JZ_GPIO_PORTB(2)
-#define JZ_GPIO_MEM_ADDR3 JZ_GPIO_PORTB(3)
-#define JZ_GPIO_MEM_ADDR4 JZ_GPIO_PORTB(4)
-#define JZ_GPIO_MEM_ADDR5 JZ_GPIO_PORTB(5)
-#define JZ_GPIO_MEM_ADDR6 JZ_GPIO_PORTB(6)
-#define JZ_GPIO_MEM_ADDR7 JZ_GPIO_PORTB(7)
-#define JZ_GPIO_MEM_ADDR8 JZ_GPIO_PORTB(8)
-#define JZ_GPIO_MEM_ADDR9 JZ_GPIO_PORTB(9)
-#define JZ_GPIO_MEM_ADDR10 JZ_GPIO_PORTB(10)
-#define JZ_GPIO_MEM_ADDR11 JZ_GPIO_PORTB(11)
-#define JZ_GPIO_MEM_ADDR12 JZ_GPIO_PORTB(12)
-#define JZ_GPIO_MEM_ADDR13 JZ_GPIO_PORTB(13)
-#define JZ_GPIO_MEM_ADDR14 JZ_GPIO_PORTB(14)
-#define JZ_GPIO_MEM_ADDR15 JZ_GPIO_PORTB(15)
-#define JZ_GPIO_MEM_ADDR16 JZ_GPIO_PORTB(16)
-#define JZ_GPIO_LCD_CLS JZ_GPIO_PORTB(17)
-#define JZ_GPIO_LCD_SPL JZ_GPIO_PORTB(18)
-#define JZ_GPIO_MEM_DCS JZ_GPIO_PORTB(19)
-#define JZ_GPIO_MEM_RAS JZ_GPIO_PORTB(20)
-#define JZ_GPIO_MEM_CAS JZ_GPIO_PORTB(21)
-#define JZ_GPIO_MEM_SDWE JZ_GPIO_PORTB(22)
-#define JZ_GPIO_MEM_CKE JZ_GPIO_PORTB(23)
-#define JZ_GPIO_MEM_CKO JZ_GPIO_PORTB(24)
-#define JZ_GPIO_MEM_CS0 JZ_GPIO_PORTB(25)
-#define JZ_GPIO_MEM_CS1 JZ_GPIO_PORTB(26)
-#define JZ_GPIO_MEM_CS2 JZ_GPIO_PORTB(27)
-#define JZ_GPIO_MEM_CS3 JZ_GPIO_PORTB(28)
-#define JZ_GPIO_MEM_RD JZ_GPIO_PORTB(29)
-#define JZ_GPIO_MEM_WR JZ_GPIO_PORTB(30)
-#define JZ_GPIO_MEM_WE0 JZ_GPIO_PORTB(31)
-
-#define JZ_GPIO_FUNC_MEM_ADDR0 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR1 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR2 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR3 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR4 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR5 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR6 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR7 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR8 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR9 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR10 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR11 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR12 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR13 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR14 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR15 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_ADDR16 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_CLS JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_SPL JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_DCS JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_RAS JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CAS JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_SDWE JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CKE JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CKO JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CS0 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CS1 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CS2 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_CS3 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_RD JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WR JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WE0 JZ_GPIO_FUNC1
-
-
-#define JZ_GPIO_MEM_ADDR21 JZ_GPIO_PORTB(17)
-#define JZ_GPIO_MEM_ADDR22 JZ_GPIO_PORTB(18)
-
-#define JZ_GPIO_FUNC_MEM_ADDR21 JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_ADDR22 JZ_GPIO_FUNC2
-
-/* Port C function pins */
-#define JZ_GPIO_LCD_DATA0 JZ_GPIO_PORTC(0)
-#define JZ_GPIO_LCD_DATA1 JZ_GPIO_PORTC(1)
-#define JZ_GPIO_LCD_DATA2 JZ_GPIO_PORTC(2)
-#define JZ_GPIO_LCD_DATA3 JZ_GPIO_PORTC(3)
-#define JZ_GPIO_LCD_DATA4 JZ_GPIO_PORTC(4)
-#define JZ_GPIO_LCD_DATA5 JZ_GPIO_PORTC(5)
-#define JZ_GPIO_LCD_DATA6 JZ_GPIO_PORTC(6)
-#define JZ_GPIO_LCD_DATA7 JZ_GPIO_PORTC(7)
-#define JZ_GPIO_LCD_DATA8 JZ_GPIO_PORTC(8)
-#define JZ_GPIO_LCD_DATA9 JZ_GPIO_PORTC(9)
-#define JZ_GPIO_LCD_DATA10 JZ_GPIO_PORTC(10)
-#define JZ_GPIO_LCD_DATA11 JZ_GPIO_PORTC(11)
-#define JZ_GPIO_LCD_DATA12 JZ_GPIO_PORTC(12)
-#define JZ_GPIO_LCD_DATA13 JZ_GPIO_PORTC(13)
-#define JZ_GPIO_LCD_DATA14 JZ_GPIO_PORTC(14)
-#define JZ_GPIO_LCD_DATA15 JZ_GPIO_PORTC(15)
-#define JZ_GPIO_LCD_DATA16 JZ_GPIO_PORTC(16)
-#define JZ_GPIO_LCD_DATA17 JZ_GPIO_PORTC(17)
-#define JZ_GPIO_LCD_PCLK JZ_GPIO_PORTC(18)
-#define JZ_GPIO_LCD_HSYNC JZ_GPIO_PORTC(19)
-#define JZ_GPIO_LCD_VSYNC JZ_GPIO_PORTC(20)
-#define JZ_GPIO_LCD_DE JZ_GPIO_PORTC(21)
-#define JZ_GPIO_LCD_PS JZ_GPIO_PORTC(22)
-#define JZ_GPIO_LCD_REV JZ_GPIO_PORTC(23)
-#define JZ_GPIO_MEM_WE1 JZ_GPIO_PORTC(24)
-#define JZ_GPIO_MEM_WE2 JZ_GPIO_PORTC(25)
-#define JZ_GPIO_MEM_WE3 JZ_GPIO_PORTC(26)
-#define JZ_GPIO_MEM_WAIT JZ_GPIO_PORTC(27)
-#define JZ_GPIO_MEM_FRE JZ_GPIO_PORTC(28)
-#define JZ_GPIO_MEM_FWE JZ_GPIO_PORTC(29)
-
-#define JZ_GPIO_FUNC_LCD_DATA0 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA1 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA2 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA3 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA4 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA5 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA6 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA7 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA8 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA9 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA10 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA11 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA12 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA13 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA14 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA15 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA16 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DATA17 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_PCLK JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_VSYNC JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_HSYNC JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_DE JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_PS JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_LCD_REV JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WE1 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WE2 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WE3 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_WAIT JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_FRE JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MEM_FWE JZ_GPIO_FUNC1
-
-
-#define JZ_GPIO_MEM_ADDR19 JZ_GPIO_PORTB(22)
-#define JZ_GPIO_MEM_ADDR20 JZ_GPIO_PORTB(23)
-
-#define JZ_GPIO_FUNC_MEM_ADDR19 JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_ADDR20 JZ_GPIO_FUNC2
-
-/* Port D function pins */
-#define JZ_GPIO_CIM_DATA0 JZ_GPIO_PORTD(0)
-#define JZ_GPIO_CIM_DATA1 JZ_GPIO_PORTD(1)
-#define JZ_GPIO_CIM_DATA2 JZ_GPIO_PORTD(2)
-#define JZ_GPIO_CIM_DATA3 JZ_GPIO_PORTD(3)
-#define JZ_GPIO_CIM_DATA4 JZ_GPIO_PORTD(4)
-#define JZ_GPIO_CIM_DATA5 JZ_GPIO_PORTD(5)
-#define JZ_GPIO_CIM_DATA6 JZ_GPIO_PORTD(6)
-#define JZ_GPIO_CIM_DATA7 JZ_GPIO_PORTD(7)
-#define JZ_GPIO_MSC_CMD JZ_GPIO_PORTD(8)
-#define JZ_GPIO_MSC_CLK JZ_GPIO_PORTD(9)
-#define JZ_GPIO_MSC_DATA0 JZ_GPIO_PORTD(10)
-#define JZ_GPIO_MSC_DATA1 JZ_GPIO_PORTD(11)
-#define JZ_GPIO_MSC_DATA2 JZ_GPIO_PORTD(12)
-#define JZ_GPIO_MSC_DATA3 JZ_GPIO_PORTD(13)
-#define JZ_GPIO_CIM_MCLK JZ_GPIO_PORTD(14)
-#define JZ_GPIO_CIM_PCLK JZ_GPIO_PORTD(15)
-#define JZ_GPIO_CIM_VSYNC JZ_GPIO_PORTD(16)
-#define JZ_GPIO_CIM_HSYNC JZ_GPIO_PORTD(17)
-#define JZ_GPIO_SPI_CLK JZ_GPIO_PORTD(18)
-#define JZ_GPIO_SPI_CE0 JZ_GPIO_PORTD(19)
-#define JZ_GPIO_SPI_DT JZ_GPIO_PORTD(20)
-#define JZ_GPIO_SPI_DR JZ_GPIO_PORTD(21)
-#define JZ_GPIO_SPI_CE1 JZ_GPIO_PORTD(22)
-#define JZ_GPIO_PWM0 JZ_GPIO_PORTD(23)
-#define JZ_GPIO_PWM1 JZ_GPIO_PORTD(24)
-#define JZ_GPIO_PWM2 JZ_GPIO_PORTD(25)
-#define JZ_GPIO_PWM3 JZ_GPIO_PORTD(26)
-#define JZ_GPIO_PWM4 JZ_GPIO_PORTD(27)
-#define JZ_GPIO_PWM5 JZ_GPIO_PORTD(28)
-#define JZ_GPIO_PWM6 JZ_GPIO_PORTD(30)
-#define JZ_GPIO_PWM7 JZ_GPIO_PORTD(31)
-
-#define JZ_GPIO_FUNC_CIM_DATA JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_CIM_DATA0 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA1 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA2 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA3 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA4 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA5 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA6 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_CIM_DATA7 JZ_GPIO_FUNC_CIM_DATA
-#define JZ_GPIO_FUNC_MSC_CMD JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MSC_CLK JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MSC_DATA JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_MSC_DATA0 JZ_GPIO_FUNC_MSC_DATA
-#define JZ_GPIO_FUNC_MSC_DATA1 JZ_GPIO_FUNC_MSC_DATA
-#define JZ_GPIO_FUNC_MSC_DATA2 JZ_GPIO_FUNC_MSC_DATA
-#define JZ_GPIO_FUNC_MSC_DATA3 JZ_GPIO_FUNC_MSC_DATA
-#define JZ_GPIO_FUNC_CIM_MCLK JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_CIM_PCLK JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_CIM_VSYNC JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_CIM_HSYNC JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_SPI_CLK JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_SPI_CE0 JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_SPI_DT JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_SPI_DR JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_SPI_CE1 JZ_GPIO_FUNC1
-
-#define JZ_GPIO_FUNC_PWM JZ_GPIO_FUNC1
-#define JZ_GPIO_FUNC_PWM0 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM1 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM2 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM3 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM4 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM5 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM6 JZ_GPIO_FUNC_PWM
-#define JZ_GPIO_FUNC_PWM7 JZ_GPIO_FUNC_PWM
-
-#define JZ_GPIO_MEM_SCLK_RSTN JZ_GPIO_PORTD(18)
-#define JZ_GPIO_MEM_BCLK JZ_GPIO_PORTD(19)
-#define JZ_GPIO_MEM_SDATO JZ_GPIO_PORTD(20)
-#define JZ_GPIO_MEM_SDATI JZ_GPIO_PORTD(21)
-#define JZ_GPIO_MEM_SYNC JZ_GPIO_PORTD(22)
-#define JZ_GPIO_I2C_SDA JZ_GPIO_PORTD(23)
-#define JZ_GPIO_I2C_SCK JZ_GPIO_PORTD(24)
-#define JZ_GPIO_UART0_TXD JZ_GPIO_PORTD(25)
-#define JZ_GPIO_UART0_RXD JZ_GPIO_PORTD(26)
-#define JZ_GPIO_MEM_ADDR17 JZ_GPIO_PORTD(27)
-#define JZ_GPIO_MEM_ADDR18 JZ_GPIO_PORTD(28)
-#define JZ_GPIO_UART0_CTS JZ_GPIO_PORTD(30)
-#define JZ_GPIO_UART0_RTS JZ_GPIO_PORTD(31)
-
-#define JZ_GPIO_FUNC_MEM_SCLK_RSTN JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_BCLK JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_SDATO JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_SDATI JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_SYNC JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_I2C_SDA JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_I2C_SCK JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_UART0_TXD JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_UART0_RXD JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_ADDR17 JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_MEM_ADDR18 JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_UART0_CTS JZ_GPIO_FUNC2
-#define JZ_GPIO_FUNC_UART0_RTS JZ_GPIO_FUNC2
-
-#define JZ_GPIO_UART1_RXD JZ_GPIO_PORTD(30)
-#define JZ_GPIO_UART1_TXD JZ_GPIO_PORTD(31)
-
-#define JZ_GPIO_FUNC_UART1_RXD JZ_GPIO_FUNC3
-#define JZ_GPIO_FUNC_UART1_TXD JZ_GPIO_FUNC3
-
#endif
diff --git a/arch/mips/jz4740/Makefile b/arch/mips/jz4740/Makefile
index 39d70bd..6b9c1f7 100644
--- a/arch/mips/jz4740/Makefile
+++ b/arch/mips/jz4740/Makefile
@@ -7,8 +7,6 @@
obj-y += prom.o time.o reset.o setup.o \
platform.o timer.o
-obj-$(CONFIG_MACH_JZ4740) += gpio.o
-
CFLAGS_setup.o = -I$(src)/../../../scripts/dtc/libfdt
# board specific support
diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c
index a5bd94b..6d7f975 100644
--- a/arch/mips/jz4740/board-qi_lb60.c
+++ b/arch/mips/jz4740/board-qi_lb60.c
@@ -22,6 +22,8 @@
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_gpio.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinconf-generic.h>
#include <linux/power_supply.h>
#include <linux/power/jz4740-battery.h>
#include <linux/power/gpio-charger.h>
@@ -159,7 +161,7 @@
static struct gpiod_lookup_table qi_lb60_nand_gpio_table = {
.dev_id = "jz4740-nand.0",
.table = {
- GPIO_LOOKUP("Bank C", 30, "busy", 0),
+ GPIO_LOOKUP("GPIOC", 30, "busy", 0),
{ },
},
};
@@ -421,8 +423,8 @@
static struct gpiod_lookup_table qi_lb60_audio_gpio_table = {
.dev_id = "qi-lb60-audio",
.table = {
- GPIO_LOOKUP("Bank B", 29, "snd", 0),
- GPIO_LOOKUP("Bank D", 4, "amp", 0),
+ GPIO_LOOKUP("GPIOB", 29, "snd", 0),
+ GPIO_LOOKUP("GPIOD", 4, "amp", 0),
{ },
},
};
@@ -447,13 +449,36 @@
&qi_lb60_audio_device,
};
-static void __init board_gpio_setup(void)
-{
- /* We only need to enable/disable pullup here for pins used in generic
- * drivers. Everything else is done by the drivers themselves. */
- jz_gpio_disable_pullup(QI_LB60_GPIO_SD_VCC_EN_N);
- jz_gpio_disable_pullup(QI_LB60_GPIO_SD_CD);
-}
+static unsigned long pin_cfg_bias_disable[] = {
+ PIN_CONFIG_BIAS_DISABLE,
+};
+
+static struct pinctrl_map pin_map[] __initdata = {
+ /* NAND pin configuration */
+ PIN_MAP_MUX_GROUP_DEFAULT("jz4740-nand",
+ "10010000.jz4740-pinctrl", "nand", "nand-cs1"),
+
+ /* fbdev pin configuration */
+ PIN_MAP_MUX_GROUP("jz4740-fb", PINCTRL_STATE_DEFAULT,
+ "10010000.jz4740-pinctrl", "lcd", "lcd-8bit"),
+ PIN_MAP_MUX_GROUP("jz4740-fb", PINCTRL_STATE_SLEEP,
+ "10010000.jz4740-pinctrl", "lcd", "lcd-no-pins"),
+
+ /* MMC pin configuration */
+ PIN_MAP_MUX_GROUP_DEFAULT("jz4740-mmc.0",
+ "10010000.jz4740-pinctrl", "mmc", "mmc-1bit"),
+ PIN_MAP_MUX_GROUP_DEFAULT("jz4740-mmc.0",
+ "10010000.jz4740-pinctrl", "mmc", "mmc-4bit"),
+ PIN_MAP_CONFIGS_PIN_DEFAULT("jz4740-mmc.0",
+ "10010000.jz4740-pinctrl", "PD0", pin_cfg_bias_disable),
+ PIN_MAP_CONFIGS_PIN_DEFAULT("jz4740-mmc.0",
+ "10010000.jz4740-pinctrl", "PD2", pin_cfg_bias_disable),
+
+ /* PWM pin configuration */
+ PIN_MAP_MUX_GROUP_DEFAULT("jz4740-pwm",
+ "10010000.jz4740-pinctrl", "pwm4", "pwm4"),
+};
+
static int __init qi_lb60_init_platform_devices(void)
{
@@ -469,6 +494,7 @@
ARRAY_SIZE(qi_lb60_spi_board_info));
pwm_add_table(qi_lb60_pwm_lookup, ARRAY_SIZE(qi_lb60_pwm_lookup));
+ pinctrl_register_mappings(pin_map, ARRAY_SIZE(pin_map));
return platform_add_devices(jz_platform_devices,
ARRAY_SIZE(jz_platform_devices));
@@ -479,8 +505,6 @@
{
printk(KERN_INFO "Qi Hardware JZ4740 QI LB60 setup\n");
- board_gpio_setup();
-
if (qi_lb60_init_platform_devices())
panic("Failed to initialize platform devices");
diff --git a/arch/mips/jz4740/gpio.c b/arch/mips/jz4740/gpio.c
deleted file mode 100644
index cac1ccd..0000000
--- a/arch/mips/jz4740/gpio.c
+++ /dev/null
@@ -1,519 +0,0 @@
-/*
- * Copyright (C) 2009-2010, Lars-Peter Clausen <lars@metafoo.de>
- * JZ4740 platform GPIO support
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/export.h>
-#include <linux/init.h>
-
-#include <linux/io.h>
-#include <linux/gpio/driver.h>
-/* FIXME: needed for gpio_request(), try to remove consumer API from driver */
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/irqchip/ingenic.h>
-#include <linux/bitops.h>
-
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-
-#include <asm/mach-jz4740/base.h>
-#include <asm/mach-jz4740/gpio.h>
-
-#define JZ4740_GPIO_BASE_A (32*0)
-#define JZ4740_GPIO_BASE_B (32*1)
-#define JZ4740_GPIO_BASE_C (32*2)
-#define JZ4740_GPIO_BASE_D (32*3)
-
-#define JZ4740_GPIO_NUM_A 32
-#define JZ4740_GPIO_NUM_B 32
-#define JZ4740_GPIO_NUM_C 31
-#define JZ4740_GPIO_NUM_D 32
-
-#define JZ4740_IRQ_GPIO_BASE_A (JZ4740_IRQ_GPIO(0) + JZ4740_GPIO_BASE_A)
-#define JZ4740_IRQ_GPIO_BASE_B (JZ4740_IRQ_GPIO(0) + JZ4740_GPIO_BASE_B)
-#define JZ4740_IRQ_GPIO_BASE_C (JZ4740_IRQ_GPIO(0) + JZ4740_GPIO_BASE_C)
-#define JZ4740_IRQ_GPIO_BASE_D (JZ4740_IRQ_GPIO(0) + JZ4740_GPIO_BASE_D)
-
-#define JZ_REG_GPIO_PIN 0x00
-#define JZ_REG_GPIO_DATA 0x10
-#define JZ_REG_GPIO_DATA_SET 0x14
-#define JZ_REG_GPIO_DATA_CLEAR 0x18
-#define JZ_REG_GPIO_MASK 0x20
-#define JZ_REG_GPIO_MASK_SET 0x24
-#define JZ_REG_GPIO_MASK_CLEAR 0x28
-#define JZ_REG_GPIO_PULL 0x30
-#define JZ_REG_GPIO_PULL_SET 0x34
-#define JZ_REG_GPIO_PULL_CLEAR 0x38
-#define JZ_REG_GPIO_FUNC 0x40
-#define JZ_REG_GPIO_FUNC_SET 0x44
-#define JZ_REG_GPIO_FUNC_CLEAR 0x48
-#define JZ_REG_GPIO_SELECT 0x50
-#define JZ_REG_GPIO_SELECT_SET 0x54
-#define JZ_REG_GPIO_SELECT_CLEAR 0x58
-#define JZ_REG_GPIO_DIRECTION 0x60
-#define JZ_REG_GPIO_DIRECTION_SET 0x64
-#define JZ_REG_GPIO_DIRECTION_CLEAR 0x68
-#define JZ_REG_GPIO_TRIGGER 0x70
-#define JZ_REG_GPIO_TRIGGER_SET 0x74
-#define JZ_REG_GPIO_TRIGGER_CLEAR 0x78
-#define JZ_REG_GPIO_FLAG 0x80
-#define JZ_REG_GPIO_FLAG_CLEAR 0x14
-
-#define GPIO_TO_BIT(gpio) BIT(gpio & 0x1f)
-#define GPIO_TO_REG(gpio, reg) (gpio_to_jz_gpio_chip(gpio)->base + (reg))
-#define CHIP_TO_REG(chip, reg) (gpio_chip_to_jz_gpio_chip(chip)->base + (reg))
-
-struct jz_gpio_chip {
- unsigned int irq;
- unsigned int irq_base;
- uint32_t edge_trigger_both;
-
- void __iomem *base;
-
- struct gpio_chip gpio_chip;
-};
-
-static struct jz_gpio_chip jz4740_gpio_chips[];
-
-static inline struct jz_gpio_chip *gpio_to_jz_gpio_chip(unsigned int gpio)
-{
- return &jz4740_gpio_chips[gpio >> 5];
-}
-
-static inline struct jz_gpio_chip *gpio_chip_to_jz_gpio_chip(struct gpio_chip *gc)
-{
- return gpiochip_get_data(gc);
-}
-
-static inline struct jz_gpio_chip *irq_to_jz_gpio_chip(struct irq_data *data)
-{
- struct irq_chip_generic *gc = irq_data_get_irq_chip_data(data);
- return gc->private;
-}
-
-static inline void jz_gpio_write_bit(unsigned int gpio, unsigned int reg)
-{
- writel(GPIO_TO_BIT(gpio), GPIO_TO_REG(gpio, reg));
-}
-
-int jz_gpio_set_function(int gpio, enum jz_gpio_function function)
-{
- if (function == JZ_GPIO_FUNC_NONE) {
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_FUNC_CLEAR);
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_SELECT_CLEAR);
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_TRIGGER_CLEAR);
- } else {
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_FUNC_SET);
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_TRIGGER_CLEAR);
- switch (function) {
- case JZ_GPIO_FUNC1:
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_SELECT_CLEAR);
- break;
- case JZ_GPIO_FUNC3:
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_TRIGGER_SET);
- case JZ_GPIO_FUNC2: /* Falltrough */
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_SELECT_SET);
- break;
- default:
- BUG();
- break;
- }
- }
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(jz_gpio_set_function);
-
-int jz_gpio_bulk_request(const struct jz_gpio_bulk_request *request, size_t num)
-{
- size_t i;
- int ret;
-
- for (i = 0; i < num; ++i, ++request) {
- ret = gpio_request(request->gpio, request->name);
- if (ret)
- goto err;
- jz_gpio_set_function(request->gpio, request->function);
- }
-
- return 0;
-
-err:
- for (--request; i > 0; --i, --request) {
- gpio_free(request->gpio);
- jz_gpio_set_function(request->gpio, JZ_GPIO_FUNC_NONE);
- }
-
- return ret;
-}
-EXPORT_SYMBOL_GPL(jz_gpio_bulk_request);
-
-void jz_gpio_bulk_free(const struct jz_gpio_bulk_request *request, size_t num)
-{
- size_t i;
-
- for (i = 0; i < num; ++i, ++request) {
- gpio_free(request->gpio);
- jz_gpio_set_function(request->gpio, JZ_GPIO_FUNC_NONE);
- }
-
-}
-EXPORT_SYMBOL_GPL(jz_gpio_bulk_free);
-
-void jz_gpio_bulk_suspend(const struct jz_gpio_bulk_request *request, size_t num)
-{
- size_t i;
-
- for (i = 0; i < num; ++i, ++request) {
- jz_gpio_set_function(request->gpio, JZ_GPIO_FUNC_NONE);
- jz_gpio_write_bit(request->gpio, JZ_REG_GPIO_DIRECTION_CLEAR);
- jz_gpio_write_bit(request->gpio, JZ_REG_GPIO_PULL_SET);
- }
-}
-EXPORT_SYMBOL_GPL(jz_gpio_bulk_suspend);
-
-void jz_gpio_bulk_resume(const struct jz_gpio_bulk_request *request, size_t num)
-{
- size_t i;
-
- for (i = 0; i < num; ++i, ++request)
- jz_gpio_set_function(request->gpio, request->function);
-}
-EXPORT_SYMBOL_GPL(jz_gpio_bulk_resume);
-
-void jz_gpio_enable_pullup(unsigned gpio)
-{
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_PULL_CLEAR);
-}
-EXPORT_SYMBOL_GPL(jz_gpio_enable_pullup);
-
-void jz_gpio_disable_pullup(unsigned gpio)
-{
- jz_gpio_write_bit(gpio, JZ_REG_GPIO_PULL_SET);
-}
-EXPORT_SYMBOL_GPL(jz_gpio_disable_pullup);
-
-static int jz_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
-{
- return !!(readl(CHIP_TO_REG(chip, JZ_REG_GPIO_PIN)) & BIT(gpio));
-}
-
-static void jz_gpio_set_value(struct gpio_chip *chip, unsigned gpio, int value)
-{
- uint32_t __iomem *reg = CHIP_TO_REG(chip, JZ_REG_GPIO_DATA_SET);
- reg += !value;
- writel(BIT(gpio), reg);
-}
-
-static int jz_gpio_direction_output(struct gpio_chip *chip, unsigned gpio,
- int value)
-{
- writel(BIT(gpio), CHIP_TO_REG(chip, JZ_REG_GPIO_DIRECTION_SET));
- jz_gpio_set_value(chip, gpio, value);
-
- return 0;
-}
-
-static int jz_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
-{
- writel(BIT(gpio), CHIP_TO_REG(chip, JZ_REG_GPIO_DIRECTION_CLEAR));
-
- return 0;
-}
-
-static int jz_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
-{
- struct jz_gpio_chip *jz_gpio = gpiochip_get_data(chip);
-
- return jz_gpio->irq_base + gpio;
-}
-
-int jz_gpio_port_direction_input(int port, uint32_t mask)
-{
- writel(mask, GPIO_TO_REG(port, JZ_REG_GPIO_DIRECTION_CLEAR));
-
- return 0;
-}
-EXPORT_SYMBOL(jz_gpio_port_direction_input);
-
-int jz_gpio_port_direction_output(int port, uint32_t mask)
-{
- writel(mask, GPIO_TO_REG(port, JZ_REG_GPIO_DIRECTION_SET));
-
- return 0;
-}
-EXPORT_SYMBOL(jz_gpio_port_direction_output);
-
-void jz_gpio_port_set_value(int port, uint32_t value, uint32_t mask)
-{
- writel(~value & mask, GPIO_TO_REG(port, JZ_REG_GPIO_DATA_CLEAR));
- writel(value & mask, GPIO_TO_REG(port, JZ_REG_GPIO_DATA_SET));
-}
-EXPORT_SYMBOL(jz_gpio_port_set_value);
-
-uint32_t jz_gpio_port_get_value(int port, uint32_t mask)
-{
- uint32_t value = readl(GPIO_TO_REG(port, JZ_REG_GPIO_PIN));
-
- return value & mask;
-}
-EXPORT_SYMBOL(jz_gpio_port_get_value);
-
-#define IRQ_TO_BIT(irq) BIT((irq - JZ4740_IRQ_GPIO(0)) & 0x1f)
-
-static void jz_gpio_check_trigger_both(struct jz_gpio_chip *chip, unsigned int irq)
-{
- uint32_t value;
- void __iomem *reg;
- uint32_t mask = IRQ_TO_BIT(irq);
-
- if (!(chip->edge_trigger_both & mask))
- return;
-
- reg = chip->base;
-
- value = readl(chip->base + JZ_REG_GPIO_PIN);
- if (value & mask)
- reg += JZ_REG_GPIO_DIRECTION_CLEAR;
- else
- reg += JZ_REG_GPIO_DIRECTION_SET;
-
- writel(mask, reg);
-}
-
-static void jz_gpio_irq_demux_handler(struct irq_desc *desc)
-{
- uint32_t flag;
- unsigned int gpio_irq;
- struct jz_gpio_chip *chip = irq_desc_get_handler_data(desc);
-
- flag = readl(chip->base + JZ_REG_GPIO_FLAG);
- if (!flag)
- return;
-
- gpio_irq = chip->irq_base + __fls(flag);
-
- jz_gpio_check_trigger_both(chip, gpio_irq);
-
- generic_handle_irq(gpio_irq);
-};
-
-static inline void jz_gpio_set_irq_bit(struct irq_data *data, unsigned int reg)
-{
- struct jz_gpio_chip *chip = irq_to_jz_gpio_chip(data);
- writel(IRQ_TO_BIT(data->irq), chip->base + reg);
-}
-
-static void jz_gpio_irq_unmask(struct irq_data *data)
-{
- struct jz_gpio_chip *chip = irq_to_jz_gpio_chip(data);
-
- jz_gpio_check_trigger_both(chip, data->irq);
- irq_gc_unmask_enable_reg(data);
-};
-
-/* TODO: Check if function is gpio */
-static unsigned int jz_gpio_irq_startup(struct irq_data *data)
-{
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_SELECT_SET);
- jz_gpio_irq_unmask(data);
- return 0;
-}
-
-static void jz_gpio_irq_shutdown(struct irq_data *data)
-{
- irq_gc_mask_disable_reg(data);
-
- /* Set direction to input */
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_DIRECTION_CLEAR);
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_SELECT_CLEAR);
-}
-
-static int jz_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type)
-{
- struct jz_gpio_chip *chip = irq_to_jz_gpio_chip(data);
- unsigned int irq = data->irq;
-
- if (flow_type == IRQ_TYPE_EDGE_BOTH) {
- uint32_t value = readl(chip->base + JZ_REG_GPIO_PIN);
- if (value & IRQ_TO_BIT(irq))
- flow_type = IRQ_TYPE_EDGE_FALLING;
- else
- flow_type = IRQ_TYPE_EDGE_RISING;
- chip->edge_trigger_both |= IRQ_TO_BIT(irq);
- } else {
- chip->edge_trigger_both &= ~IRQ_TO_BIT(irq);
- }
-
- switch (flow_type) {
- case IRQ_TYPE_EDGE_RISING:
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_DIRECTION_SET);
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_TRIGGER_SET);
- break;
- case IRQ_TYPE_EDGE_FALLING:
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_DIRECTION_CLEAR);
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_TRIGGER_SET);
- break;
- case IRQ_TYPE_LEVEL_HIGH:
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_DIRECTION_SET);
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_TRIGGER_CLEAR);
- break;
- case IRQ_TYPE_LEVEL_LOW:
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_DIRECTION_CLEAR);
- jz_gpio_set_irq_bit(data, JZ_REG_GPIO_TRIGGER_CLEAR);
- break;
- default:
- return -EINVAL;
- }
-
- return 0;
-}
-
-static int jz_gpio_irq_set_wake(struct irq_data *data, unsigned int on)
-{
- struct jz_gpio_chip *chip = irq_to_jz_gpio_chip(data);
-
- irq_gc_set_wake(data, on);
- irq_set_irq_wake(chip->irq, on);
-
- return 0;
-}
-
-#define JZ4740_GPIO_CHIP(_bank) { \
- .irq_base = JZ4740_IRQ_GPIO_BASE_ ## _bank, \
- .gpio_chip = { \
- .label = "Bank " # _bank, \
- .owner = THIS_MODULE, \
- .set = jz_gpio_set_value, \
- .get = jz_gpio_get_value, \
- .direction_output = jz_gpio_direction_output, \
- .direction_input = jz_gpio_direction_input, \
- .to_irq = jz_gpio_to_irq, \
- .base = JZ4740_GPIO_BASE_ ## _bank, \
- .ngpio = JZ4740_GPIO_NUM_ ## _bank, \
- }, \
-}
-
-static struct jz_gpio_chip jz4740_gpio_chips[] = {
- JZ4740_GPIO_CHIP(A),
- JZ4740_GPIO_CHIP(B),
- JZ4740_GPIO_CHIP(C),
- JZ4740_GPIO_CHIP(D),
-};
-
-static void jz4740_gpio_chip_init(struct jz_gpio_chip *chip, unsigned int id)
-{
- struct irq_chip_generic *gc;
- struct irq_chip_type *ct;
-
- chip->base = ioremap(JZ4740_GPIO_BASE_ADDR + (id * 0x100), 0x100);
-
- chip->irq = JZ4740_IRQ_INTC_GPIO(id);
- irq_set_chained_handler_and_data(chip->irq,
- jz_gpio_irq_demux_handler, chip);
-
- gc = irq_alloc_generic_chip(chip->gpio_chip.label, 1, chip->irq_base,
- chip->base, handle_level_irq);
-
- gc->wake_enabled = IRQ_MSK(chip->gpio_chip.ngpio);
- gc->private = chip;
-
- ct = gc->chip_types;
- ct->regs.enable = JZ_REG_GPIO_MASK_CLEAR;
- ct->regs.disable = JZ_REG_GPIO_MASK_SET;
- ct->regs.ack = JZ_REG_GPIO_FLAG_CLEAR;
-
- ct->chip.name = "GPIO";
- ct->chip.irq_mask = irq_gc_mask_disable_reg;
- ct->chip.irq_unmask = jz_gpio_irq_unmask;
- ct->chip.irq_ack = irq_gc_ack_set_bit;
- ct->chip.irq_suspend = ingenic_intc_irq_suspend;
- ct->chip.irq_resume = ingenic_intc_irq_resume;
- ct->chip.irq_startup = jz_gpio_irq_startup;
- ct->chip.irq_shutdown = jz_gpio_irq_shutdown;
- ct->chip.irq_set_type = jz_gpio_irq_set_type;
- ct->chip.irq_set_wake = jz_gpio_irq_set_wake;
- ct->chip.flags = IRQCHIP_SET_TYPE_MASKED;
-
- irq_setup_generic_chip(gc, IRQ_MSK(chip->gpio_chip.ngpio),
- IRQ_GC_INIT_NESTED_LOCK, 0, IRQ_NOPROBE | IRQ_LEVEL);
-
- gpiochip_add_data(&chip->gpio_chip, chip);
-}
-
-static int __init jz4740_gpio_init(void)
-{
- unsigned int i;
-
- for (i = 0; i < ARRAY_SIZE(jz4740_gpio_chips); ++i)
- jz4740_gpio_chip_init(&jz4740_gpio_chips[i], i);
-
- printk(KERN_INFO "JZ4740 GPIO initialized\n");
-
- return 0;
-}
-arch_initcall(jz4740_gpio_init);
-
-#ifdef CONFIG_DEBUG_FS
-
-static inline void gpio_seq_reg(struct seq_file *s, struct jz_gpio_chip *chip,
- const char *name, unsigned int reg)
-{
- seq_printf(s, "\t%s: %08x\n", name, readl(chip->base + reg));
-}
-
-static int gpio_regs_show(struct seq_file *s, void *unused)
-{
- struct jz_gpio_chip *chip = jz4740_gpio_chips;
- int i;
-
- for (i = 0; i < ARRAY_SIZE(jz4740_gpio_chips); ++i, ++chip) {
- seq_printf(s, "==GPIO %d==\n", i);
- gpio_seq_reg(s, chip, "Pin", JZ_REG_GPIO_PIN);
- gpio_seq_reg(s, chip, "Data", JZ_REG_GPIO_DATA);
- gpio_seq_reg(s, chip, "Mask", JZ_REG_GPIO_MASK);
- gpio_seq_reg(s, chip, "Pull", JZ_REG_GPIO_PULL);
- gpio_seq_reg(s, chip, "Func", JZ_REG_GPIO_FUNC);
- gpio_seq_reg(s, chip, "Select", JZ_REG_GPIO_SELECT);
- gpio_seq_reg(s, chip, "Direction", JZ_REG_GPIO_DIRECTION);
- gpio_seq_reg(s, chip, "Trigger", JZ_REG_GPIO_TRIGGER);
- gpio_seq_reg(s, chip, "Flag", JZ_REG_GPIO_FLAG);
- }
-
- return 0;
-}
-
-static int gpio_regs_open(struct inode *inode, struct file *file)
-{
- return single_open(file, gpio_regs_show, NULL);
-}
-
-static const struct file_operations gpio_regs_operations = {
- .open = gpio_regs_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = single_release,
-};
-
-static int __init gpio_debugfs_init(void)
-{
- (void) debugfs_create_file("jz_regs_gpio", S_IFREG | S_IRUGO,
- NULL, NULL, &gpio_regs_operations);
- return 0;
-}
-subsys_initcall(gpio_debugfs_init);
-
-#endif
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 23ca51e..45ed9ac 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -242,6 +242,16 @@
If unsure, say N.
+config GPIO_INGENIC
+ tristate "Ingenic JZ47xx SoCs GPIO support"
+ depends on MACH_INGENIC || COMPILE_TEST
+ select GPIOLIB_IRQCHIP
+ help
+ Say yes here to support the GPIO functionality present on the
+ JZ4740 and JZ4780 SoCs from Ingenic.
+
+ If unsure, say N.
+
config GPIO_IOP
tristate "Intel IOP GPIO"
depends on ARCH_IOP32X || ARCH_IOP33X || COMPILE_TEST
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 68b9627..d293967 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -55,6 +55,7 @@
obj-$(CONFIG_GPIO_GRGPIO) += gpio-grgpio.o
obj-$(CONFIG_HTC_EGPIO) += gpio-htc-egpio.o
obj-$(CONFIG_GPIO_ICH) += gpio-ich.o
+obj-$(CONFIG_GPIO_INGENIC) += gpio-ingenic.o
obj-$(CONFIG_GPIO_IOP) += gpio-iop.o
obj-$(CONFIG_GPIO_IT87) += gpio-it87.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
diff --git a/drivers/gpio/gpio-ingenic.c b/drivers/gpio/gpio-ingenic.c
new file mode 100644
index 0000000..2547807
--- /dev/null
+++ b/drivers/gpio/gpio-ingenic.c
@@ -0,0 +1,394 @@
+/*
+ * Ingenic JZ47xx GPIO driver
+ *
+ * Copyright (c) 2017 Paul Cercueil <paul@crapouillou.net>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/regmap.h>
+
+#define GPIO_PIN 0x00
+#define GPIO_MSK 0x20
+
+#define JZ4740_GPIO_DATA 0x10
+#define JZ4740_GPIO_SELECT 0x50
+#define JZ4740_GPIO_DIR 0x60
+#define JZ4740_GPIO_TRIG 0x70
+#define JZ4740_GPIO_FLAG 0x80
+
+#define JZ4770_GPIO_INT 0x10
+#define JZ4770_GPIO_PAT1 0x30
+#define JZ4770_GPIO_PAT0 0x40
+#define JZ4770_GPIO_FLAG 0x50
+
+#define REG_SET(x) ((x) + 0x4)
+#define REG_CLEAR(x) ((x) + 0x8)
+
+enum jz_version {
+ ID_JZ4740,
+ ID_JZ4770,
+ ID_JZ4780,
+};
+
+struct ingenic_gpio_chip {
+ struct regmap *map;
+ struct gpio_chip gc;
+ struct irq_chip irq_chip;
+ unsigned int irq, reg_base;
+ enum jz_version version;
+};
+
+static u32 gpio_ingenic_read_reg(struct ingenic_gpio_chip *jzgc, u8 reg)
+{
+ unsigned int val;
+
+ regmap_read(jzgc->map, jzgc->reg_base + reg, &val);
+
+ return (u32) val;
+}
+
+static void gpio_ingenic_set_bit(struct ingenic_gpio_chip *jzgc,
+ u8 reg, u8 offset, bool set)
+{
+ if (set)
+ reg = REG_SET(reg);
+ else
+ reg = REG_CLEAR(reg);
+
+ regmap_write(jzgc->map, jzgc->reg_base + reg, BIT(offset));
+}
+
+static inline bool gpio_get_value(struct ingenic_gpio_chip *jzgc, u8 offset)
+{
+ unsigned int val = gpio_ingenic_read_reg(jzgc, GPIO_PIN);
+
+ return !!(val & BIT(offset));
+}
+
+static void gpio_set_value(struct ingenic_gpio_chip *jzgc, u8 offset, int value)
+{
+ if (jzgc->version >= ID_JZ4770)
+ gpio_ingenic_set_bit(jzgc, JZ4770_GPIO_PAT0, offset, !!value);
+ else
+ gpio_ingenic_set_bit(jzgc, JZ4740_GPIO_DATA, offset, !!value);
+}
+
+static void irq_set_type(struct ingenic_gpio_chip *jzgc,
+ u8 offset, unsigned int type)
+{
+ u8 reg1, reg2;
+
+ if (jzgc->version >= ID_JZ4770) {
+ reg1 = JZ4770_GPIO_PAT1;
+ reg2 = JZ4770_GPIO_PAT0;
+ } else {
+ reg1 = JZ4740_GPIO_TRIG;
+ reg2 = JZ4740_GPIO_DIR;
+ }
+
+ switch (type) {
+ case IRQ_TYPE_EDGE_RISING:
+ gpio_ingenic_set_bit(jzgc, reg2, offset, true);
+ gpio_ingenic_set_bit(jzgc, reg1, offset, true);
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ gpio_ingenic_set_bit(jzgc, reg2, offset, false);
+ gpio_ingenic_set_bit(jzgc, reg1, offset, true);
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ gpio_ingenic_set_bit(jzgc, reg2, offset, true);
+ gpio_ingenic_set_bit(jzgc, reg1, offset, false);
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ default:
+ gpio_ingenic_set_bit(jzgc, reg2, offset, false);
+ gpio_ingenic_set_bit(jzgc, reg1, offset, false);
+ break;
+ }
+}
+
+static void ingenic_gpio_irq_mask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ gpio_ingenic_set_bit(jzgc, GPIO_MSK, irqd->hwirq, true);
+}
+
+static void ingenic_gpio_irq_unmask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ gpio_ingenic_set_bit(jzgc, GPIO_MSK, irqd->hwirq, false);
+}
+
+static void ingenic_gpio_irq_enable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+ int irq = irqd->hwirq;
+
+ if (jzgc->version >= ID_JZ4770)
+ gpio_ingenic_set_bit(jzgc, JZ4770_GPIO_INT, irq, true);
+ else
+ gpio_ingenic_set_bit(jzgc, JZ4740_GPIO_SELECT, irq, true);
+
+ ingenic_gpio_irq_unmask(irqd);
+}
+
+static void ingenic_gpio_irq_disable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+ int irq = irqd->hwirq;
+
+ ingenic_gpio_irq_mask(irqd);
+
+ if (jzgc->version >= ID_JZ4770)
+ gpio_ingenic_set_bit(jzgc, JZ4770_GPIO_INT, irq, false);
+ else
+ gpio_ingenic_set_bit(jzgc, JZ4740_GPIO_SELECT, irq, false);
+}
+
+static void ingenic_gpio_irq_ack(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+ int irq = irqd->hwirq;
+ bool high;
+
+ if (irqd_get_trigger_type(irqd) == IRQ_TYPE_EDGE_BOTH) {
+ /*
+ * Switch to an interrupt for the opposite edge to the one that
+ * triggered the interrupt being ACKed.
+ */
+ high = gpio_get_value(jzgc, irq);
+ if (high)
+ irq_set_type(jzgc, irq, IRQ_TYPE_EDGE_FALLING);
+ else
+ irq_set_type(jzgc, irq, IRQ_TYPE_EDGE_RISING);
+ }
+
+ if (jzgc->version >= ID_JZ4770)
+ gpio_ingenic_set_bit(jzgc, JZ4770_GPIO_FLAG, irq, false);
+ else
+ gpio_ingenic_set_bit(jzgc, JZ4740_GPIO_DATA, irq, true);
+}
+
+static int ingenic_gpio_irq_set_type(struct irq_data *irqd, unsigned int type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ switch (type) {
+ case IRQ_TYPE_EDGE_BOTH:
+ case IRQ_TYPE_EDGE_RISING:
+ case IRQ_TYPE_EDGE_FALLING:
+ irq_set_handler_locked(irqd, handle_edge_irq);
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ case IRQ_TYPE_LEVEL_LOW:
+ irq_set_handler_locked(irqd, handle_level_irq);
+ break;
+ default:
+ irq_set_handler_locked(irqd, handle_bad_irq);
+ }
+
+ if (type == IRQ_TYPE_EDGE_BOTH) {
+ /*
+ * The hardware does not support interrupts on both edges. The
+ * best we can do is to set up a single-edge interrupt and then
+ * switch to the opposing edge when ACKing the interrupt.
+ */
+ bool high = gpio_get_value(jzgc, irqd->hwirq);
+
+ type = high ? IRQ_TYPE_EDGE_FALLING : IRQ_TYPE_EDGE_RISING;
+ }
+
+ irq_set_type(jzgc, irqd->hwirq, type);
+ return 0;
+}
+
+static int ingenic_gpio_irq_set_wake(struct irq_data *irqd, unsigned int on)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ return irq_set_irq_wake(jzgc->irq, on);
+}
+
+static void ingenic_gpio_irq_handler(struct irq_desc *desc)
+{
+ struct gpio_chip *gc = irq_desc_get_handler_data(desc);
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+ struct irq_chip *irq_chip = irq_data_get_irq_chip(&desc->irq_data);
+ unsigned long flag, i;
+
+ chained_irq_enter(irq_chip, desc);
+
+ if (jzgc->version >= ID_JZ4770)
+ flag = gpio_ingenic_read_reg(jzgc, JZ4770_GPIO_FLAG);
+ else
+ flag = gpio_ingenic_read_reg(jzgc, JZ4740_GPIO_FLAG);
+
+ for_each_set_bit(i, &flag, 32)
+ generic_handle_irq(irq_linear_revmap(gc->irqdomain, i));
+ chained_irq_exit(irq_chip, desc);
+}
+
+static void ingenic_gpio_set(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ gpio_set_value(jzgc, offset, value);
+}
+
+static int ingenic_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ struct ingenic_gpio_chip *jzgc = gpiochip_get_data(gc);
+
+ return (int) gpio_get_value(jzgc, offset);
+}
+
+static int ingenic_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ return pinctrl_gpio_direction_input(gc->base + offset);
+}
+
+static int ingenic_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ ingenic_gpio_set(gc, offset, value);
+ return pinctrl_gpio_direction_output(gc->base + offset);
+}
+
+static const struct of_device_id ingenic_gpio_of_match[] = {
+ { .compatible = "ingenic,jz4740-gpio", .data = (void *)ID_JZ4740 },
+ { .compatible = "ingenic,jz4770-gpio", .data = (void *)ID_JZ4770 },
+ { .compatible = "ingenic,jz4780-gpio", .data = (void *)ID_JZ4780 },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ingenic_gpio_of_match);
+
+static int ingenic_gpio_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *of_id = of_match_device(
+ ingenic_gpio_of_match, dev);
+ struct ingenic_gpio_chip *jzgc;
+ u32 bank;
+ int err;
+
+ jzgc = devm_kzalloc(dev, sizeof(*jzgc), GFP_KERNEL);
+ if (!jzgc)
+ return -ENOMEM;
+
+ jzgc->map = dev_get_drvdata(dev->parent);
+ if (!jzgc->map) {
+ dev_err(dev, "Cannot get parent regmap\n");
+ return -ENXIO;
+ }
+
+ err = of_property_read_u32(dev->of_node, "reg", &bank);
+ if (err) {
+ dev_err(dev, "Cannot read \"reg\" property: %i\n", err);
+ return err;
+ }
+
+ jzgc->reg_base = bank * 0x100;
+
+ jzgc->gc.label = devm_kasprintf(dev, GFP_KERNEL, "GPIO%c", 'A' + bank);
+ if (!jzgc->gc.label)
+ return -ENOMEM;
+
+ /* DO NOT EXPAND THIS: FOR BACKWARD GPIO NUMBERSPACE COMPATIBIBILITY
+ * ONLY: WORK TO TRANSITION CONSUMERS TO USE THE GPIO DESCRIPTOR API IN
+ * <linux/gpio/consumer.h> INSTEAD.
+ */
+ jzgc->gc.base = bank * 32;
+
+ jzgc->gc.ngpio = 32;
+ jzgc->gc.parent = dev;
+ jzgc->gc.of_node = dev->of_node;
+ jzgc->gc.owner = THIS_MODULE;
+ jzgc->version = (enum jz_version)of_id->data;
+
+ jzgc->gc.set = ingenic_gpio_set;
+ jzgc->gc.get = ingenic_gpio_get;
+ jzgc->gc.direction_input = ingenic_gpio_direction_input;
+ jzgc->gc.direction_output = ingenic_gpio_direction_output;
+
+ if (of_property_read_bool(dev->of_node, "gpio-ranges")) {
+ jzgc->gc.request = gpiochip_generic_request;
+ jzgc->gc.free = gpiochip_generic_free;
+ }
+
+ err = devm_gpiochip_add_data(dev, &jzgc->gc, jzgc);
+ if (err)
+ return err;
+
+ jzgc->irq = irq_of_parse_and_map(dev->of_node, 0);
+ if (!jzgc->irq)
+ return -EINVAL;
+
+ jzgc->irq_chip.name = jzgc->gc.label;
+ jzgc->irq_chip.irq_enable = ingenic_gpio_irq_enable;
+ jzgc->irq_chip.irq_disable = ingenic_gpio_irq_disable;
+ jzgc->irq_chip.irq_unmask = ingenic_gpio_irq_unmask;
+ jzgc->irq_chip.irq_mask = ingenic_gpio_irq_mask;
+ jzgc->irq_chip.irq_ack = ingenic_gpio_irq_ack;
+ jzgc->irq_chip.irq_set_type = ingenic_gpio_irq_set_type;
+ jzgc->irq_chip.irq_set_wake = ingenic_gpio_irq_set_wake;
+ jzgc->irq_chip.flags = IRQCHIP_MASK_ON_SUSPEND;
+
+ err = gpiochip_irqchip_add(&jzgc->gc, &jzgc->irq_chip, 0,
+ handle_level_irq, IRQ_TYPE_NONE);
+ if (err)
+ return err;
+
+ gpiochip_set_chained_irqchip(&jzgc->gc, &jzgc->irq_chip,
+ jzgc->irq, ingenic_gpio_irq_handler);
+ return 0;
+}
+
+static int ingenic_gpio_remove(struct platform_device *pdev)
+{
+ return 0;
+}
+
+static struct platform_driver ingenic_gpio_driver = {
+ .driver = {
+ .name = "gpio-ingenic",
+ .of_match_table = of_match_ptr(ingenic_gpio_of_match),
+ },
+ .probe = ingenic_gpio_probe,
+ .remove = ingenic_gpio_remove,
+};
+
+static int __init ingenic_gpio_drv_register(void)
+{
+ return platform_driver_register(&ingenic_gpio_driver);
+}
+subsys_initcall(ingenic_gpio_drv_register);
+
+static void __exit ingenic_gpio_drv_unregister(void)
+{
+ platform_driver_unregister(&ingenic_gpio_driver);
+}
+module_exit(ingenic_gpio_drv_unregister);
+
+MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
+MODULE_DESCRIPTION("Ingenic JZ47xx GPIO driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c
index 57e254a..7db8c7a 100644
--- a/drivers/mmc/host/jz4740_mmc.c
+++ b/drivers/mmc/host/jz4740_mmc.c
@@ -20,6 +20,7 @@
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/module.h>
+#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/scatterlist.h>
@@ -27,7 +28,6 @@
#include <linux/bitops.h>
#include <linux/gpio.h>
-#include <asm/mach-jz4740/gpio.h>
#include <asm/cacheflush.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
@@ -901,15 +901,6 @@
.enable_sdio_irq = jz4740_mmc_enable_sdio_irq,
};
-static const struct jz_gpio_bulk_request jz4740_mmc_pins[] = {
- JZ_GPIO_BULK_PIN(MSC_CMD),
- JZ_GPIO_BULK_PIN(MSC_CLK),
- JZ_GPIO_BULK_PIN(MSC_DATA0),
- JZ_GPIO_BULK_PIN(MSC_DATA1),
- JZ_GPIO_BULK_PIN(MSC_DATA2),
- JZ_GPIO_BULK_PIN(MSC_DATA3),
-};
-
static int jz4740_mmc_request_gpio(struct device *dev, int gpio,
const char *name, bool output, int value)
{
@@ -973,15 +964,6 @@
gpio_free(pdata->gpio_power);
}
-static inline size_t jz4740_mmc_num_pins(struct jz4740_mmc_host *host)
-{
- size_t num_pins = ARRAY_SIZE(jz4740_mmc_pins);
- if (host->pdata && host->pdata->data_1bit)
- num_pins -= 3;
-
- return num_pins;
-}
-
static int jz4740_mmc_probe(struct platform_device* pdev)
{
int ret;
@@ -1022,15 +1004,9 @@
goto err_free_host;
}
- ret = jz_gpio_bulk_request(jz4740_mmc_pins, jz4740_mmc_num_pins(host));
- if (ret) {
- dev_err(&pdev->dev, "Failed to request mmc pins: %d\n", ret);
- goto err_free_host;
- }
-
ret = jz4740_mmc_request_gpios(mmc, pdev);
if (ret)
- goto err_gpio_bulk_free;
+ goto err_release_dma;
mmc->ops = &jz4740_mmc_ops;
mmc->f_min = JZ_MMC_CLK_RATE / 128;
@@ -1086,10 +1062,9 @@
free_irq(host->irq, host);
err_free_gpios:
jz4740_mmc_free_gpios(pdev);
-err_gpio_bulk_free:
+err_release_dma:
if (host->use_dma)
jz4740_mmc_release_dma_channels(host);
- jz_gpio_bulk_free(jz4740_mmc_pins, jz4740_mmc_num_pins(host));
err_free_host:
mmc_free_host(mmc);
@@ -1109,7 +1084,6 @@
free_irq(host->irq, host);
jz4740_mmc_free_gpios(pdev);
- jz_gpio_bulk_free(jz4740_mmc_pins, jz4740_mmc_num_pins(host));
if (host->use_dma)
jz4740_mmc_release_dma_channels(host);
@@ -1123,20 +1097,12 @@
static int jz4740_mmc_suspend(struct device *dev)
{
- struct jz4740_mmc_host *host = dev_get_drvdata(dev);
-
- jz_gpio_bulk_suspend(jz4740_mmc_pins, jz4740_mmc_num_pins(host));
-
- return 0;
+ return pinctrl_pm_select_sleep_state(dev);
}
static int jz4740_mmc_resume(struct device *dev)
{
- struct jz4740_mmc_host *host = dev_get_drvdata(dev);
-
- jz_gpio_bulk_resume(jz4740_mmc_pins, jz4740_mmc_num_pins(host));
-
- return 0;
+ return pinctrl_pm_select_default_state(dev);
}
static SIMPLE_DEV_PM_OPS(jz4740_mmc_pm_ops, jz4740_mmc_suspend,
diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c
index 5551c36..0d06a1f 100644
--- a/drivers/mtd/nand/jz4740_nand.c
+++ b/drivers/mtd/nand/jz4740_nand.c
@@ -25,7 +25,6 @@
#include <linux/gpio.h>
-#include <asm/mach-jz4740/gpio.h>
#include <asm/mach-jz4740/jz4740_nand.h>
#define JZ_REG_NAND_CTRL 0x50
@@ -310,34 +309,20 @@
uint8_t *nand_dev_id)
{
int ret;
- int gpio;
- char gpio_name[9];
char res_name[6];
uint32_t ctrl;
struct nand_chip *chip = &nand->chip;
struct mtd_info *mtd = nand_to_mtd(chip);
- /* Request GPIO port. */
- gpio = JZ_GPIO_MEM_CS0 + bank - 1;
- sprintf(gpio_name, "NAND CS%d", bank);
- ret = gpio_request(gpio, gpio_name);
- if (ret) {
- dev_warn(&pdev->dev,
- "Failed to request %s gpio %d: %d\n",
- gpio_name, gpio, ret);
- goto notfound_gpio;
- }
-
/* Request I/O resource. */
sprintf(res_name, "bank%d", bank);
ret = jz_nand_ioremap_resource(pdev, res_name,
&nand->bank_mem[bank - 1],
&nand->bank_base[bank - 1]);
if (ret)
- goto notfound_resource;
+ return ret;
/* Enable chip in bank. */
- jz_gpio_set_function(gpio, JZ_GPIO_FUNC_MEM_CS0);
ctrl = readl(nand->base + JZ_REG_NAND_CTRL);
ctrl |= JZ_NAND_CTRL_ENABLE_CHIP(bank - 1);
writel(ctrl, nand->base + JZ_REG_NAND_CTRL);
@@ -377,12 +362,8 @@
dev_info(&pdev->dev, "No chip found on bank %i\n", bank);
ctrl &= ~(JZ_NAND_CTRL_ENABLE_CHIP(bank - 1));
writel(ctrl, nand->base + JZ_REG_NAND_CTRL);
- jz_gpio_set_function(gpio, JZ_GPIO_FUNC_NONE);
jz_nand_iounmap_resource(nand->bank_mem[bank - 1],
nand->bank_base[bank - 1]);
-notfound_resource:
- gpio_free(gpio);
-notfound_gpio:
return ret;
}
@@ -503,7 +484,6 @@
err_unclaim_banks:
while (chipnr--) {
unsigned char bank = nand->banks[chipnr];
- gpio_free(JZ_GPIO_MEM_CS0 + bank - 1);
jz_nand_iounmap_resource(nand->bank_mem[bank - 1],
nand->bank_base[bank - 1]);
}
@@ -530,7 +510,6 @@
if (bank != 0) {
jz_nand_iounmap_resource(nand->bank_mem[bank - 1],
nand->bank_base[bank - 1]);
- gpio_free(JZ_GPIO_MEM_CS0 + bank - 1);
}
}
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 145f7ee..7cacf89 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -296,6 +296,15 @@
help
This selects the pinctrl driver for Xilinx Zynq.
+config PINCTRL_INGENIC
+ bool "Pinctrl driver for the Ingenic JZ47xx SoCs"
+ default y
+ depends on MACH_INGENIC || COMPILE_TEST
+ select GENERIC_PINCONF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select REGMAP_MMIO
+
source "drivers/pinctrl/aspeed/Kconfig"
source "drivers/pinctrl/bcm/Kconfig"
source "drivers/pinctrl/berlin/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index e22af00..a054364 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -39,6 +39,7 @@
obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-tb10x.o
obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
+obj-$(CONFIG_PINCTRL_INGENIC) += pinctrl-ingenic.o
obj-$(CONFIG_ARCH_ASPEED) += aspeed/
obj-y += bcm/
diff --git a/drivers/pinctrl/pinctrl-ingenic.c b/drivers/pinctrl/pinctrl-ingenic.c
new file mode 100644
index 0000000..d8473d9
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-ingenic.c
@@ -0,0 +1,852 @@
+/*
+ * Ingenic SoCs pinctrl driver
+ *
+ * Copyright (c) 2017 Paul Cercueil <paul@crapouillou.net>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/compiler.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinmux.h"
+
+#define JZ4740_GPIO_DATA 0x10
+#define JZ4740_GPIO_PULL_DIS 0x30
+#define JZ4740_GPIO_FUNC 0x40
+#define JZ4740_GPIO_SELECT 0x50
+#define JZ4740_GPIO_DIR 0x60
+#define JZ4740_GPIO_TRIG 0x70
+#define JZ4740_GPIO_FLAG 0x80
+
+#define JZ4770_GPIO_INT 0x10
+#define JZ4770_GPIO_MSK 0x20
+#define JZ4770_GPIO_PAT1 0x30
+#define JZ4770_GPIO_PAT0 0x40
+#define JZ4770_GPIO_FLAG 0x50
+#define JZ4770_GPIO_PEN 0x70
+
+#define REG_SET(x) ((x) + 0x4)
+#define REG_CLEAR(x) ((x) + 0x8)
+
+#define PINS_PER_GPIO_CHIP 32
+
+enum jz_version {
+ ID_JZ4740,
+ ID_JZ4770,
+ ID_JZ4780,
+};
+
+struct ingenic_chip_info {
+ unsigned int num_chips;
+
+ const struct group_desc *groups;
+ unsigned int num_groups;
+
+ const struct function_desc *functions;
+ unsigned int num_functions;
+
+ const u32 *pull_ups, *pull_downs;
+};
+
+struct ingenic_pinctrl {
+ struct device *dev;
+ struct regmap *map;
+ struct pinctrl_dev *pctl;
+ struct pinctrl_pin_desc *pdesc;
+ enum jz_version version;
+
+ const struct ingenic_chip_info *info;
+};
+
+static const u32 jz4740_pull_ups[4] = {
+ 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
+};
+
+static const u32 jz4740_pull_downs[4] = {
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+};
+
+static int jz4740_mmc_1bit_pins[] = { 0x69, 0x68, 0x6a, };
+static int jz4740_mmc_4bit_pins[] = { 0x6b, 0x6c, 0x6d, };
+static int jz4740_uart0_data_pins[] = { 0x7a, 0x79, };
+static int jz4740_uart0_hwflow_pins[] = { 0x7e, 0x7f, };
+static int jz4740_uart1_data_pins[] = { 0x7e, 0x7f, };
+static int jz4740_lcd_8bit_pins[] = {
+ 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47, 0x52, 0x53, 0x54,
+};
+static int jz4740_lcd_16bit_pins[] = {
+ 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, 0x55,
+};
+static int jz4740_lcd_18bit_pins[] = { 0x50, 0x51, };
+static int jz4740_lcd_18bit_tft_pins[] = { 0x56, 0x57, 0x31, 0x32, };
+static int jz4740_nand_cs1_pins[] = { 0x39, };
+static int jz4740_nand_cs2_pins[] = { 0x3a, };
+static int jz4740_nand_cs3_pins[] = { 0x3b, };
+static int jz4740_nand_cs4_pins[] = { 0x3c, };
+static int jz4740_pwm_pwm0_pins[] = { 0x77, };
+static int jz4740_pwm_pwm1_pins[] = { 0x78, };
+static int jz4740_pwm_pwm2_pins[] = { 0x79, };
+static int jz4740_pwm_pwm3_pins[] = { 0x7a, };
+static int jz4740_pwm_pwm4_pins[] = { 0x7b, };
+static int jz4740_pwm_pwm5_pins[] = { 0x7c, };
+static int jz4740_pwm_pwm6_pins[] = { 0x7e, };
+static int jz4740_pwm_pwm7_pins[] = { 0x7f, };
+
+static int jz4740_mmc_1bit_funcs[] = { 0, 0, 0, };
+static int jz4740_mmc_4bit_funcs[] = { 0, 0, 0, };
+static int jz4740_uart0_data_funcs[] = { 1, 1, };
+static int jz4740_uart0_hwflow_funcs[] = { 1, 1, };
+static int jz4740_uart1_data_funcs[] = { 2, 2, };
+static int jz4740_lcd_8bit_funcs[] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, };
+static int jz4740_lcd_16bit_funcs[] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, };
+static int jz4740_lcd_18bit_funcs[] = { 0, 0, };
+static int jz4740_lcd_18bit_tft_funcs[] = { 0, 0, 0, 0, };
+static int jz4740_nand_cs1_funcs[] = { 0, };
+static int jz4740_nand_cs2_funcs[] = { 0, };
+static int jz4740_nand_cs3_funcs[] = { 0, };
+static int jz4740_nand_cs4_funcs[] = { 0, };
+static int jz4740_pwm_pwm0_funcs[] = { 0, };
+static int jz4740_pwm_pwm1_funcs[] = { 0, };
+static int jz4740_pwm_pwm2_funcs[] = { 0, };
+static int jz4740_pwm_pwm3_funcs[] = { 0, };
+static int jz4740_pwm_pwm4_funcs[] = { 0, };
+static int jz4740_pwm_pwm5_funcs[] = { 0, };
+static int jz4740_pwm_pwm6_funcs[] = { 0, };
+static int jz4740_pwm_pwm7_funcs[] = { 0, };
+
+#define INGENIC_PIN_GROUP(name, id) \
+ { \
+ name, \
+ id##_pins, \
+ ARRAY_SIZE(id##_pins), \
+ id##_funcs, \
+ }
+
+static const struct group_desc jz4740_groups[] = {
+ INGENIC_PIN_GROUP("mmc-1bit", jz4740_mmc_1bit),
+ INGENIC_PIN_GROUP("mmc-4bit", jz4740_mmc_4bit),
+ INGENIC_PIN_GROUP("uart0-data", jz4740_uart0_data),
+ INGENIC_PIN_GROUP("uart0-hwflow", jz4740_uart0_hwflow),
+ INGENIC_PIN_GROUP("uart1-data", jz4740_uart1_data),
+ INGENIC_PIN_GROUP("lcd-8bit", jz4740_lcd_8bit),
+ INGENIC_PIN_GROUP("lcd-16bit", jz4740_lcd_16bit),
+ INGENIC_PIN_GROUP("lcd-18bit", jz4740_lcd_18bit),
+ INGENIC_PIN_GROUP("lcd-18bit-tft", jz4740_lcd_18bit_tft),
+ { "lcd-no-pins", },
+ INGENIC_PIN_GROUP("nand-cs1", jz4740_nand_cs1),
+ INGENIC_PIN_GROUP("nand-cs2", jz4740_nand_cs2),
+ INGENIC_PIN_GROUP("nand-cs3", jz4740_nand_cs3),
+ INGENIC_PIN_GROUP("nand-cs4", jz4740_nand_cs4),
+ INGENIC_PIN_GROUP("pwm0", jz4740_pwm_pwm0),
+ INGENIC_PIN_GROUP("pwm1", jz4740_pwm_pwm1),
+ INGENIC_PIN_GROUP("pwm2", jz4740_pwm_pwm2),
+ INGENIC_PIN_GROUP("pwm3", jz4740_pwm_pwm3),
+ INGENIC_PIN_GROUP("pwm4", jz4740_pwm_pwm4),
+ INGENIC_PIN_GROUP("pwm5", jz4740_pwm_pwm5),
+ INGENIC_PIN_GROUP("pwm6", jz4740_pwm_pwm6),
+ INGENIC_PIN_GROUP("pwm7", jz4740_pwm_pwm7),
+};
+
+static const char *jz4740_mmc_groups[] = { "mmc-1bit", "mmc-4bit", };
+static const char *jz4740_uart0_groups[] = { "uart0-data", "uart0-hwflow", };
+static const char *jz4740_uart1_groups[] = { "uart1-data", };
+static const char *jz4740_lcd_groups[] = {
+ "lcd-8bit", "lcd-16bit", "lcd-18bit", "lcd-18bit-tft", "lcd-no-pins",
+};
+static const char *jz4740_nand_groups[] = {
+ "nand-cs1", "nand-cs2", "nand-cs3", "nand-cs4",
+};
+static const char *jz4740_pwm0_groups[] = { "pwm0", };
+static const char *jz4740_pwm1_groups[] = { "pwm1", };
+static const char *jz4740_pwm2_groups[] = { "pwm2", };
+static const char *jz4740_pwm3_groups[] = { "pwm3", };
+static const char *jz4740_pwm4_groups[] = { "pwm4", };
+static const char *jz4740_pwm5_groups[] = { "pwm5", };
+static const char *jz4740_pwm6_groups[] = { "pwm6", };
+static const char *jz4740_pwm7_groups[] = { "pwm7", };
+
+static const struct function_desc jz4740_functions[] = {
+ { "mmc", jz4740_mmc_groups, ARRAY_SIZE(jz4740_mmc_groups), },
+ { "uart0", jz4740_uart0_groups, ARRAY_SIZE(jz4740_uart0_groups), },
+ { "uart1", jz4740_uart1_groups, ARRAY_SIZE(jz4740_uart1_groups), },
+ { "lcd", jz4740_lcd_groups, ARRAY_SIZE(jz4740_lcd_groups), },
+ { "nand", jz4740_nand_groups, ARRAY_SIZE(jz4740_nand_groups), },
+ { "pwm0", jz4740_pwm0_groups, ARRAY_SIZE(jz4740_pwm0_groups), },
+ { "pwm1", jz4740_pwm1_groups, ARRAY_SIZE(jz4740_pwm1_groups), },
+ { "pwm2", jz4740_pwm2_groups, ARRAY_SIZE(jz4740_pwm2_groups), },
+ { "pwm3", jz4740_pwm3_groups, ARRAY_SIZE(jz4740_pwm3_groups), },
+ { "pwm4", jz4740_pwm4_groups, ARRAY_SIZE(jz4740_pwm4_groups), },
+ { "pwm5", jz4740_pwm5_groups, ARRAY_SIZE(jz4740_pwm5_groups), },
+ { "pwm6", jz4740_pwm6_groups, ARRAY_SIZE(jz4740_pwm6_groups), },
+ { "pwm7", jz4740_pwm7_groups, ARRAY_SIZE(jz4740_pwm7_groups), },
+};
+
+static const struct ingenic_chip_info jz4740_chip_info = {
+ .num_chips = 4,
+ .groups = jz4740_groups,
+ .num_groups = ARRAY_SIZE(jz4740_groups),
+ .functions = jz4740_functions,
+ .num_functions = ARRAY_SIZE(jz4740_functions),
+ .pull_ups = jz4740_pull_ups,
+ .pull_downs = jz4740_pull_downs,
+};
+
+static const u32 jz4770_pull_ups[6] = {
+ 0x3fffffff, 0xfff0030c, 0xffffffff, 0xffff4fff, 0xfffffb7c, 0xffa7f00f,
+};
+
+static const u32 jz4770_pull_downs[6] = {
+ 0x00000000, 0x000f0c03, 0x00000000, 0x0000b000, 0x00000483, 0x00580ff0,
+};
+
+static int jz4770_uart0_data_pins[] = { 0xa0, 0xa3, };
+static int jz4770_uart0_hwflow_pins[] = { 0xa1, 0xa2, };
+static int jz4770_uart1_data_pins[] = { 0x7a, 0x7c, };
+static int jz4770_uart1_hwflow_pins[] = { 0x7b, 0x7d, };
+static int jz4770_uart2_data_pins[] = { 0x66, 0x67, };
+static int jz4770_uart2_hwflow_pins[] = { 0x65, 0x64, };
+static int jz4770_uart3_data_pins[] = { 0x6c, 0x85, };
+static int jz4770_uart3_hwflow_pins[] = { 0x88, 0x89, };
+static int jz4770_uart4_data_pins[] = { 0x54, 0x4a, };
+static int jz4770_mmc0_8bit_a_pins[] = { 0x04, 0x05, 0x06, 0x07, 0x18, };
+static int jz4770_mmc0_4bit_a_pins[] = { 0x15, 0x16, 0x17, };
+static int jz4770_mmc0_1bit_a_pins[] = { 0x12, 0x13, 0x14, };
+static int jz4770_mmc0_4bit_e_pins[] = { 0x95, 0x96, 0x97, };
+static int jz4770_mmc0_1bit_e_pins[] = { 0x9c, 0x9d, 0x94, };
+static int jz4770_mmc1_4bit_d_pins[] = { 0x75, 0x76, 0x77, };
+static int jz4770_mmc1_1bit_d_pins[] = { 0x78, 0x79, 0x74, };
+static int jz4770_mmc1_4bit_e_pins[] = { 0x95, 0x96, 0x97, };
+static int jz4770_mmc1_1bit_e_pins[] = { 0x9c, 0x9d, 0x94, };
+static int jz4770_nemc_data_pins[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
+};
+static int jz4770_nemc_cle_ale_pins[] = { 0x20, 0x21, };
+static int jz4770_nemc_addr_pins[] = { 0x22, 0x23, 0x24, 0x25, };
+static int jz4770_nemc_rd_we_pins[] = { 0x10, 0x11, };
+static int jz4770_nemc_frd_fwe_pins[] = { 0x12, 0x13, };
+static int jz4770_nemc_cs1_pins[] = { 0x15, };
+static int jz4770_nemc_cs2_pins[] = { 0x16, };
+static int jz4770_nemc_cs3_pins[] = { 0x17, };
+static int jz4770_nemc_cs4_pins[] = { 0x18, };
+static int jz4770_nemc_cs5_pins[] = { 0x19, };
+static int jz4770_nemc_cs6_pins[] = { 0x1a, };
+static int jz4770_i2c0_pins[] = { 0x6e, 0x6f, };
+static int jz4770_i2c1_pins[] = { 0x8e, 0x8f, };
+static int jz4770_i2c2_pins[] = { 0xb0, 0xb1, };
+static int jz4770_i2c3_pins[] = { 0x6a, 0x6b, };
+static int jz4770_i2c4_e_pins[] = { 0x8c, 0x8d, };
+static int jz4770_i2c4_f_pins[] = { 0xb9, 0xb8, };
+static int jz4770_cim_pins[] = {
+ 0x26, 0x27, 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f, 0x30, 0x31,
+};
+static int jz4770_lcd_32bit_pins[] = {
+ 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,
+ 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f,
+ 0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57,
+ 0x58, 0x59, 0x51,
+};
+static int jz4770_pwm_pwm0_pins[] = { 0x80, };
+static int jz4770_pwm_pwm1_pins[] = { 0x81, };
+static int jz4770_pwm_pwm2_pins[] = { 0x82, };
+static int jz4770_pwm_pwm3_pins[] = { 0x83, };
+static int jz4770_pwm_pwm4_pins[] = { 0x84, };
+static int jz4770_pwm_pwm5_pins[] = { 0x85, };
+static int jz4770_pwm_pwm6_pins[] = { 0x6a, };
+static int jz4770_pwm_pwm7_pins[] = { 0x6b, };
+
+static int jz4770_uart0_data_funcs[] = { 0, 0, };
+static int jz4770_uart0_hwflow_funcs[] = { 0, 0, };
+static int jz4770_uart1_data_funcs[] = { 0, 0, };
+static int jz4770_uart1_hwflow_funcs[] = { 0, 0, };
+static int jz4770_uart2_data_funcs[] = { 1, 1, };
+static int jz4770_uart2_hwflow_funcs[] = { 1, 1, };
+static int jz4770_uart3_data_funcs[] = { 0, 1, };
+static int jz4770_uart3_hwflow_funcs[] = { 0, 0, };
+static int jz4770_uart4_data_funcs[] = { 2, 2, };
+static int jz4770_mmc0_8bit_a_funcs[] = { 1, 1, 1, 1, 1, };
+static int jz4770_mmc0_4bit_a_funcs[] = { 1, 1, 1, };
+static int jz4770_mmc0_1bit_a_funcs[] = { 1, 1, 0, };
+static int jz4770_mmc0_4bit_e_funcs[] = { 0, 0, 0, };
+static int jz4770_mmc0_1bit_e_funcs[] = { 0, 0, 0, };
+static int jz4770_mmc1_4bit_d_funcs[] = { 0, 0, 0, };
+static int jz4770_mmc1_1bit_d_funcs[] = { 0, 0, 0, };
+static int jz4770_mmc1_4bit_e_funcs[] = { 1, 1, 1, };
+static int jz4770_mmc1_1bit_e_funcs[] = { 1, 1, 1, };
+static int jz4770_nemc_data_funcs[] = { 0, 0, 0, 0, 0, 0, 0, 0, };
+static int jz4770_nemc_cle_ale_funcs[] = { 0, 0, };
+static int jz4770_nemc_addr_funcs[] = { 0, 0, 0, 0, };
+static int jz4770_nemc_rd_we_funcs[] = { 0, 0, };
+static int jz4770_nemc_frd_fwe_funcs[] = { 0, 0, };
+static int jz4770_nemc_cs1_funcs[] = { 0, };
+static int jz4770_nemc_cs2_funcs[] = { 0, };
+static int jz4770_nemc_cs3_funcs[] = { 0, };
+static int jz4770_nemc_cs4_funcs[] = { 0, };
+static int jz4770_nemc_cs5_funcs[] = { 0, };
+static int jz4770_nemc_cs6_funcs[] = { 0, };
+static int jz4770_i2c0_funcs[] = { 0, 0, };
+static int jz4770_i2c1_funcs[] = { 0, 0, };
+static int jz4770_i2c2_funcs[] = { 2, 2, };
+static int jz4770_i2c3_funcs[] = { 1, 1, };
+static int jz4770_i2c4_e_funcs[] = { 1, 1, };
+static int jz4770_i2c4_f_funcs[] = { 1, 1, };
+static int jz4770_cim_funcs[] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, };
+static int jz4770_lcd_32bit_funcs[] = {
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0,
+};
+static int jz4770_pwm_pwm0_funcs[] = { 0, };
+static int jz4770_pwm_pwm1_funcs[] = { 0, };
+static int jz4770_pwm_pwm2_funcs[] = { 0, };
+static int jz4770_pwm_pwm3_funcs[] = { 0, };
+static int jz4770_pwm_pwm4_funcs[] = { 0, };
+static int jz4770_pwm_pwm5_funcs[] = { 0, };
+static int jz4770_pwm_pwm6_funcs[] = { 0, };
+static int jz4770_pwm_pwm7_funcs[] = { 0, };
+
+static const struct group_desc jz4770_groups[] = {
+ INGENIC_PIN_GROUP("uart0-data", jz4770_uart0_data),
+ INGENIC_PIN_GROUP("uart0-hwflow", jz4770_uart0_hwflow),
+ INGENIC_PIN_GROUP("uart1-data", jz4770_uart1_data),
+ INGENIC_PIN_GROUP("uart1-hwflow", jz4770_uart1_hwflow),
+ INGENIC_PIN_GROUP("uart2-data", jz4770_uart2_data),
+ INGENIC_PIN_GROUP("uart2-hwflow", jz4770_uart2_hwflow),
+ INGENIC_PIN_GROUP("uart3-data", jz4770_uart3_data),
+ INGENIC_PIN_GROUP("uart3-hwflow", jz4770_uart3_hwflow),
+ INGENIC_PIN_GROUP("uart4-data", jz4770_uart4_data),
+ INGENIC_PIN_GROUP("mmc0-8bit-a", jz4770_mmc0_8bit_a),
+ INGENIC_PIN_GROUP("mmc0-4bit-a", jz4770_mmc0_4bit_a),
+ INGENIC_PIN_GROUP("mmc0-1bit-a", jz4770_mmc0_1bit_a),
+ INGENIC_PIN_GROUP("mmc0-4bit-e", jz4770_mmc0_4bit_e),
+ INGENIC_PIN_GROUP("mmc0-1bit-e", jz4770_mmc0_1bit_e),
+ INGENIC_PIN_GROUP("mmc1-4bit-d", jz4770_mmc1_4bit_d),
+ INGENIC_PIN_GROUP("mmc1-1bit-d", jz4770_mmc1_1bit_d),
+ INGENIC_PIN_GROUP("mmc1-4bit-e", jz4770_mmc1_4bit_e),
+ INGENIC_PIN_GROUP("mmc1-1bit-e", jz4770_mmc1_1bit_e),
+ INGENIC_PIN_GROUP("nemc-data", jz4770_nemc_data),
+ INGENIC_PIN_GROUP("nemc-cle-ale", jz4770_nemc_cle_ale),
+ INGENIC_PIN_GROUP("nemc-addr", jz4770_nemc_addr),
+ INGENIC_PIN_GROUP("nemc-rd-we", jz4770_nemc_rd_we),
+ INGENIC_PIN_GROUP("nemc-frd-fwe", jz4770_nemc_frd_fwe),
+ INGENIC_PIN_GROUP("nemc-cs1", jz4770_nemc_cs1),
+ INGENIC_PIN_GROUP("nemc-cs2", jz4770_nemc_cs2),
+ INGENIC_PIN_GROUP("nemc-cs3", jz4770_nemc_cs3),
+ INGENIC_PIN_GROUP("nemc-cs4", jz4770_nemc_cs4),
+ INGENIC_PIN_GROUP("nemc-cs5", jz4770_nemc_cs5),
+ INGENIC_PIN_GROUP("nemc-cs6", jz4770_nemc_cs6),
+ INGENIC_PIN_GROUP("i2c0-data", jz4770_i2c0),
+ INGENIC_PIN_GROUP("i2c1-data", jz4770_i2c1),
+ INGENIC_PIN_GROUP("i2c2-data", jz4770_i2c2),
+ INGENIC_PIN_GROUP("i2c3-data", jz4770_i2c3),
+ INGENIC_PIN_GROUP("i2c4-data-e", jz4770_i2c4_e),
+ INGENIC_PIN_GROUP("i2c4-data-f", jz4770_i2c4_f),
+ INGENIC_PIN_GROUP("cim-data", jz4770_cim),
+ INGENIC_PIN_GROUP("lcd-32bit", jz4770_lcd_32bit),
+ { "lcd-no-pins", },
+ INGENIC_PIN_GROUP("pwm0", jz4770_pwm_pwm0),
+ INGENIC_PIN_GROUP("pwm1", jz4770_pwm_pwm1),
+ INGENIC_PIN_GROUP("pwm2", jz4770_pwm_pwm2),
+ INGENIC_PIN_GROUP("pwm3", jz4770_pwm_pwm3),
+ INGENIC_PIN_GROUP("pwm4", jz4770_pwm_pwm4),
+ INGENIC_PIN_GROUP("pwm5", jz4770_pwm_pwm5),
+ INGENIC_PIN_GROUP("pwm6", jz4770_pwm_pwm6),
+ INGENIC_PIN_GROUP("pwm7", jz4770_pwm_pwm7),
+};
+
+static const char *jz4770_uart0_groups[] = { "uart0-data", "uart0-hwflow", };
+static const char *jz4770_uart1_groups[] = { "uart1-data", "uart1-hwflow", };
+static const char *jz4770_uart2_groups[] = { "uart2-data", "uart2-hwflow", };
+static const char *jz4770_uart3_groups[] = { "uart3-data", "uart3-hwflow", };
+static const char *jz4770_uart4_groups[] = { "uart4-data", };
+static const char *jz4770_mmc0_groups[] = {
+ "mmc0-8bit-a", "mmc0-4bit-a", "mmc0-1bit-a",
+ "mmc0-1bit-e", "mmc0-4bit-e",
+};
+static const char *jz4770_mmc1_groups[] = {
+ "mmc1-1bit-d", "mmc1-4bit-d", "mmc1-1bit-e", "mmc1-4bit-e",
+};
+static const char *jz4770_nemc_groups[] = {
+ "nemc-data", "nemc-cle-ale", "nemc-addr", "nemc-rd-we", "nemc-frd-fwe",
+};
+static const char *jz4770_cs1_groups[] = { "nemc-cs1", };
+static const char *jz4770_cs6_groups[] = { "nemc-cs6", };
+static const char *jz4770_i2c0_groups[] = { "i2c0-data", };
+static const char *jz4770_i2c1_groups[] = { "i2c1-data", };
+static const char *jz4770_i2c2_groups[] = { "i2c2-data", };
+static const char *jz4770_i2c3_groups[] = { "i2c3-data", };
+static const char *jz4770_i2c4_groups[] = { "i2c4-data-e", "i2c4-data-f", };
+static const char *jz4770_cim_groups[] = { "cim-data", };
+static const char *jz4770_lcd_groups[] = { "lcd-32bit", "lcd-no-pins", };
+static const char *jz4770_pwm0_groups[] = { "pwm0", };
+static const char *jz4770_pwm1_groups[] = { "pwm1", };
+static const char *jz4770_pwm2_groups[] = { "pwm2", };
+static const char *jz4770_pwm3_groups[] = { "pwm3", };
+static const char *jz4770_pwm4_groups[] = { "pwm4", };
+static const char *jz4770_pwm5_groups[] = { "pwm5", };
+static const char *jz4770_pwm6_groups[] = { "pwm6", };
+static const char *jz4770_pwm7_groups[] = { "pwm7", };
+
+static const struct function_desc jz4770_functions[] = {
+ { "uart0", jz4770_uart0_groups, ARRAY_SIZE(jz4770_uart0_groups), },
+ { "uart1", jz4770_uart1_groups, ARRAY_SIZE(jz4770_uart1_groups), },
+ { "uart2", jz4770_uart2_groups, ARRAY_SIZE(jz4770_uart2_groups), },
+ { "uart3", jz4770_uart3_groups, ARRAY_SIZE(jz4770_uart3_groups), },
+ { "uart4", jz4770_uart4_groups, ARRAY_SIZE(jz4770_uart4_groups), },
+ { "mmc0", jz4770_mmc0_groups, ARRAY_SIZE(jz4770_mmc0_groups), },
+ { "mmc1", jz4770_mmc1_groups, ARRAY_SIZE(jz4770_mmc1_groups), },
+ { "nemc", jz4770_nemc_groups, ARRAY_SIZE(jz4770_nemc_groups), },
+ { "nemc-cs1", jz4770_cs1_groups, ARRAY_SIZE(jz4770_cs1_groups), },
+ { "nemc-cs6", jz4770_cs6_groups, ARRAY_SIZE(jz4770_cs6_groups), },
+ { "i2c0", jz4770_i2c0_groups, ARRAY_SIZE(jz4770_i2c0_groups), },
+ { "i2c1", jz4770_i2c1_groups, ARRAY_SIZE(jz4770_i2c1_groups), },
+ { "i2c2", jz4770_i2c2_groups, ARRAY_SIZE(jz4770_i2c2_groups), },
+ { "i2c3", jz4770_i2c3_groups, ARRAY_SIZE(jz4770_i2c3_groups), },
+ { "i2c4", jz4770_i2c4_groups, ARRAY_SIZE(jz4770_i2c4_groups), },
+ { "cim", jz4770_cim_groups, ARRAY_SIZE(jz4770_cim_groups), },
+ { "lcd", jz4770_lcd_groups, ARRAY_SIZE(jz4770_lcd_groups), },
+ { "pwm0", jz4770_pwm0_groups, ARRAY_SIZE(jz4770_pwm0_groups), },
+ { "pwm1", jz4770_pwm1_groups, ARRAY_SIZE(jz4770_pwm1_groups), },
+ { "pwm2", jz4770_pwm2_groups, ARRAY_SIZE(jz4770_pwm2_groups), },
+ { "pwm3", jz4770_pwm3_groups, ARRAY_SIZE(jz4770_pwm3_groups), },
+ { "pwm4", jz4770_pwm4_groups, ARRAY_SIZE(jz4770_pwm4_groups), },
+ { "pwm5", jz4770_pwm5_groups, ARRAY_SIZE(jz4770_pwm5_groups), },
+ { "pwm6", jz4770_pwm6_groups, ARRAY_SIZE(jz4770_pwm6_groups), },
+ { "pwm7", jz4770_pwm7_groups, ARRAY_SIZE(jz4770_pwm7_groups), },
+};
+
+static const struct ingenic_chip_info jz4770_chip_info = {
+ .num_chips = 6,
+ .groups = jz4770_groups,
+ .num_groups = ARRAY_SIZE(jz4770_groups),
+ .functions = jz4770_functions,
+ .num_functions = ARRAY_SIZE(jz4770_functions),
+ .pull_ups = jz4770_pull_ups,
+ .pull_downs = jz4770_pull_downs,
+};
+
+static inline void ingenic_config_pin(struct ingenic_pinctrl *jzpc,
+ unsigned int pin, u8 reg, bool set)
+{
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+
+ regmap_write(jzpc->map, offt * 0x100 +
+ (set ? REG_SET(reg) : REG_CLEAR(reg)), BIT(idx));
+}
+
+static inline bool ingenic_get_pin_config(struct ingenic_pinctrl *jzpc,
+ unsigned int pin, u8 reg)
+{
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+ unsigned int val;
+
+ regmap_read(jzpc->map, offt * 0x100 + reg, &val);
+
+ return val & BIT(idx);
+}
+
+static struct pinctrl_ops ingenic_pctlops = {
+ .get_groups_count = pinctrl_generic_get_group_count,
+ .get_group_name = pinctrl_generic_get_group_name,
+ .get_group_pins = pinctrl_generic_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_all,
+ .dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int ingenic_pinmux_set_pin_fn(struct ingenic_pinctrl *jzpc,
+ int pin, int func)
+{
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+
+ dev_dbg(jzpc->dev, "set pin P%c%u to function %u\n",
+ 'A' + offt, idx, func);
+
+ if (jzpc->version >= ID_JZ4770) {
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_INT, false);
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_MSK, false);
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_PAT1, func & 0x2);
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_PAT0, func & 0x1);
+ } else {
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_FUNC, true);
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_TRIG, func & 0x2);
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_SELECT, func > 0);
+ }
+
+ return 0;
+}
+
+static int ingenic_pinmux_set_mux(struct pinctrl_dev *pctldev,
+ unsigned int selector, unsigned int group)
+{
+ struct ingenic_pinctrl *jzpc = pinctrl_dev_get_drvdata(pctldev);
+ struct function_desc *func;
+ struct group_desc *grp;
+ unsigned int i;
+
+ func = pinmux_generic_get_function(pctldev, selector);
+ if (!func)
+ return -EINVAL;
+
+ grp = pinctrl_generic_get_group(pctldev, group);
+ if (!grp)
+ return -EINVAL;
+
+ dev_dbg(pctldev->dev, "enable function %s group %s\n",
+ func->name, grp->name);
+
+ for (i = 0; i < grp->num_pins; i++) {
+ int *pin_modes = grp->data;
+
+ ingenic_pinmux_set_pin_fn(jzpc, grp->pins[i], pin_modes[i]);
+ }
+
+ return 0;
+}
+
+static int ingenic_pinmux_gpio_set_direction(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int pin, bool input)
+{
+ struct ingenic_pinctrl *jzpc = pinctrl_dev_get_drvdata(pctldev);
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+
+ dev_dbg(pctldev->dev, "set pin P%c%u to %sput\n",
+ 'A' + offt, idx, input ? "in" : "out");
+
+ if (jzpc->version >= ID_JZ4770) {
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_INT, false);
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_MSK, true);
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_PAT1, input);
+ } else {
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_SELECT, false);
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_DIR, input);
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_FUNC, false);
+ }
+
+ return 0;
+}
+
+static struct pinmux_ops ingenic_pmxops = {
+ .get_functions_count = pinmux_generic_get_function_count,
+ .get_function_name = pinmux_generic_get_function_name,
+ .get_function_groups = pinmux_generic_get_function_groups,
+ .set_mux = ingenic_pinmux_set_mux,
+ .gpio_set_direction = ingenic_pinmux_gpio_set_direction,
+};
+
+static int ingenic_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ struct ingenic_pinctrl *jzpc = pinctrl_dev_get_drvdata(pctldev);
+ enum pin_config_param param = pinconf_to_config_param(*config);
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+ bool pull;
+
+ if (jzpc->version >= ID_JZ4770)
+ pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
+ else
+ pull = !ingenic_get_pin_config(jzpc, pin, JZ4740_GPIO_PULL_DIS);
+
+ switch (param) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ if (pull)
+ return -EINVAL;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!pull || !(jzpc->info->pull_ups[offt] & BIT(idx)))
+ return -EINVAL;
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!pull || !(jzpc->info->pull_downs[offt] & BIT(idx)))
+ return -EINVAL;
+ break;
+
+ default:
+ return -ENOTSUPP;
+ }
+
+ *config = pinconf_to_config_packed(param, 1);
+ return 0;
+}
+
+static void ingenic_set_bias(struct ingenic_pinctrl *jzpc,
+ unsigned int pin, bool enabled)
+{
+ if (jzpc->version >= ID_JZ4770)
+ ingenic_config_pin(jzpc, pin, JZ4770_GPIO_PEN, !enabled);
+ else
+ ingenic_config_pin(jzpc, pin, JZ4740_GPIO_PULL_DIS, !enabled);
+}
+
+static int ingenic_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+ unsigned long *configs, unsigned int num_configs)
+{
+ struct ingenic_pinctrl *jzpc = pinctrl_dev_get_drvdata(pctldev);
+ unsigned int idx = pin % PINS_PER_GPIO_CHIP;
+ unsigned int offt = pin / PINS_PER_GPIO_CHIP;
+ unsigned int cfg;
+
+ for (cfg = 0; cfg < num_configs; cfg++) {
+ switch (pinconf_to_config_param(configs[cfg])) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ case PIN_CONFIG_BIAS_PULL_UP:
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ continue;
+ default:
+ return -ENOTSUPP;
+ }
+ }
+
+ for (cfg = 0; cfg < num_configs; cfg++) {
+ switch (pinconf_to_config_param(configs[cfg])) {
+ case PIN_CONFIG_BIAS_DISABLE:
+ dev_dbg(jzpc->dev, "disable pull-over for pin P%c%u\n",
+ 'A' + offt, idx);
+ ingenic_set_bias(jzpc, pin, false);
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_UP:
+ if (!(jzpc->info->pull_ups[offt] & BIT(idx)))
+ return -EINVAL;
+ dev_dbg(jzpc->dev, "set pull-up for pin P%c%u\n",
+ 'A' + offt, idx);
+ ingenic_set_bias(jzpc, pin, true);
+ break;
+
+ case PIN_CONFIG_BIAS_PULL_DOWN:
+ if (!(jzpc->info->pull_downs[offt] & BIT(idx)))
+ return -EINVAL;
+ dev_dbg(jzpc->dev, "set pull-down for pin P%c%u\n",
+ 'A' + offt, idx);
+ ingenic_set_bias(jzpc, pin, true);
+ break;
+
+ default:
+ unreachable();
+ }
+ }
+
+ return 0;
+}
+
+static int ingenic_pinconf_group_get(struct pinctrl_dev *pctldev,
+ unsigned int group, unsigned long *config)
+{
+ const unsigned int *pins;
+ unsigned int i, npins, old = 0;
+ int ret;
+
+ ret = pinctrl_generic_get_group_pins(pctldev, group, &pins, &npins);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < npins; i++) {
+ if (ingenic_pinconf_get(pctldev, pins[i], config))
+ return -ENOTSUPP;
+
+ /* configs do not match between two pins */
+ if (i && (old != *config))
+ return -ENOTSUPP;
+
+ old = *config;
+ }
+
+ return 0;
+}
+
+static int ingenic_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned int group, unsigned long *configs,
+ unsigned int num_configs)
+{
+ const unsigned int *pins;
+ unsigned int i, npins;
+ int ret;
+
+ ret = pinctrl_generic_get_group_pins(pctldev, group, &pins, &npins);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < npins; i++) {
+ ret = ingenic_pinconf_set(pctldev,
+ pins[i], configs, num_configs);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct pinconf_ops ingenic_confops = {
+ .is_generic = true,
+ .pin_config_get = ingenic_pinconf_get,
+ .pin_config_set = ingenic_pinconf_set,
+ .pin_config_group_get = ingenic_pinconf_group_get,
+ .pin_config_group_set = ingenic_pinconf_group_set,
+};
+
+static const struct regmap_config ingenic_pinctrl_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static const struct of_device_id ingenic_pinctrl_of_match[] = {
+ { .compatible = "ingenic,jz4740-pinctrl", .data = (void *) ID_JZ4740 },
+ { .compatible = "ingenic,jz4770-pinctrl", .data = (void *) ID_JZ4770 },
+ { .compatible = "ingenic,jz4780-pinctrl", .data = (void *) ID_JZ4780 },
+ {},
+};
+
+int ingenic_pinctrl_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ingenic_pinctrl *jzpc;
+ struct pinctrl_desc *pctl_desc;
+ void __iomem *base;
+ const struct platform_device_id *id = platform_get_device_id(pdev);
+ const struct of_device_id *of_id = of_match_device(
+ ingenic_pinctrl_of_match, dev);
+ const struct ingenic_chip_info *chip_info;
+ unsigned int i;
+ int err;
+
+ jzpc = devm_kzalloc(dev, sizeof(*jzpc), GFP_KERNEL);
+ if (!jzpc)
+ return -ENOMEM;
+
+ base = devm_ioremap_resource(dev,
+ platform_get_resource(pdev, IORESOURCE_MEM, 0));
+ if (IS_ERR(base)) {
+ dev_err(dev, "Failed to ioremap registers\n");
+ return PTR_ERR(base);
+ }
+
+ jzpc->map = devm_regmap_init_mmio(dev, base,
+ &ingenic_pinctrl_regmap_config);
+ if (IS_ERR(jzpc->map)) {
+ dev_err(dev, "Failed to create regmap\n");
+ return PTR_ERR(jzpc->map);
+ }
+
+ jzpc->dev = dev;
+
+ if (of_id)
+ jzpc->version = (enum jz_version)of_id->data;
+ else
+ jzpc->version = (enum jz_version)id->driver_data;
+
+ if (jzpc->version >= ID_JZ4770)
+ chip_info = &jz4770_chip_info;
+ else
+ chip_info = &jz4740_chip_info;
+ jzpc->info = chip_info;
+
+ pctl_desc = devm_kzalloc(&pdev->dev, sizeof(*pctl_desc), GFP_KERNEL);
+ if (!pctl_desc)
+ return -ENOMEM;
+
+ /* fill in pinctrl_desc structure */
+ pctl_desc->name = dev_name(dev);
+ pctl_desc->owner = THIS_MODULE;
+ pctl_desc->pctlops = &ingenic_pctlops;
+ pctl_desc->pmxops = &ingenic_pmxops;
+ pctl_desc->confops = &ingenic_confops;
+ pctl_desc->npins = chip_info->num_chips * PINS_PER_GPIO_CHIP;
+ pctl_desc->pins = jzpc->pdesc = devm_kzalloc(&pdev->dev,
+ sizeof(*jzpc->pdesc) * pctl_desc->npins, GFP_KERNEL);
+ if (!jzpc->pdesc)
+ return -ENOMEM;
+
+ for (i = 0; i < pctl_desc->npins; i++) {
+ jzpc->pdesc[i].number = i;
+ jzpc->pdesc[i].name = kasprintf(GFP_KERNEL, "P%c%d",
+ 'A' + (i / PINS_PER_GPIO_CHIP),
+ i % PINS_PER_GPIO_CHIP);
+ }
+
+ jzpc->pctl = devm_pinctrl_register(dev, pctl_desc, jzpc);
+ if (!jzpc->pctl) {
+ dev_err(dev, "Failed to register pinctrl\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < chip_info->num_groups; i++) {
+ const struct group_desc *group = &chip_info->groups[i];
+
+ err = pinctrl_generic_add_group(jzpc->pctl, group->name,
+ group->pins, group->num_pins, group->data);
+ if (err) {
+ dev_err(dev, "Failed to register group %s\n",
+ group->name);
+ return err;
+ }
+ }
+
+ for (i = 0; i < chip_info->num_functions; i++) {
+ const struct function_desc *func = &chip_info->functions[i];
+
+ err = pinmux_generic_add_function(jzpc->pctl, func->name,
+ func->group_names, func->num_group_names,
+ func->data);
+ if (err) {
+ dev_err(dev, "Failed to register function %s\n",
+ func->name);
+ return err;
+ }
+ }
+
+ dev_set_drvdata(dev, jzpc->map);
+
+ if (dev->of_node) {
+ err = of_platform_populate(dev->of_node, NULL, NULL, dev);
+ if (err) {
+ dev_err(dev, "Failed to probe GPIO devices\n");
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id ingenic_pinctrl_ids[] = {
+ { "jz4740-pinctrl", ID_JZ4740 },
+ { "jz4770-pinctrl", ID_JZ4770 },
+ { "jz4780-pinctrl", ID_JZ4780 },
+ {},
+};
+
+static struct platform_driver ingenic_pinctrl_driver = {
+ .driver = {
+ .name = "pinctrl-ingenic",
+ .of_match_table = of_match_ptr(ingenic_pinctrl_of_match),
+ .suppress_bind_attrs = true,
+ },
+ .probe = ingenic_pinctrl_probe,
+ .id_table = ingenic_pinctrl_ids,
+};
+
+static int __init ingenic_pinctrl_drv_register(void)
+{
+ return platform_driver_register(&ingenic_pinctrl_driver);
+}
+postcore_initcall(ingenic_pinctrl_drv_register);
diff --git a/drivers/pwm/pwm-jz4740.c b/drivers/pwm/pwm-jz4740.c
index 76d1315..a75ff36 100644
--- a/drivers/pwm/pwm-jz4740.c
+++ b/drivers/pwm/pwm-jz4740.c
@@ -21,22 +21,10 @@
#include <linux/platform_device.h>
#include <linux/pwm.h>
-#include <asm/mach-jz4740/gpio.h>
#include <asm/mach-jz4740/timer.h>
#define NUM_PWM 8
-static const unsigned int jz4740_pwm_gpio_list[NUM_PWM] = {
- JZ_GPIO_PWM0,
- JZ_GPIO_PWM1,
- JZ_GPIO_PWM2,
- JZ_GPIO_PWM3,
- JZ_GPIO_PWM4,
- JZ_GPIO_PWM5,
- JZ_GPIO_PWM6,
- JZ_GPIO_PWM7,
-};
-
struct jz4740_pwm_chip {
struct pwm_chip chip;
struct clk *clk;
@@ -49,9 +37,6 @@
static int jz4740_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
{
- unsigned int gpio = jz4740_pwm_gpio_list[pwm->hwpwm];
- int ret;
-
/*
* Timers 0 and 1 are used for system tasks, so they are unavailable
* for use as PWMs.
@@ -59,15 +44,6 @@
if (pwm->hwpwm < 2)
return -EBUSY;
- ret = gpio_request(gpio, pwm->label);
- if (ret) {
- dev_err(chip->dev, "Failed to request GPIO#%u for PWM: %d\n",
- gpio, ret);
- return ret;
- }
-
- jz_gpio_set_function(gpio, JZ_GPIO_FUNC_PWM);
-
jz4740_timer_start(pwm->hwpwm);
return 0;
@@ -75,13 +51,8 @@
static void jz4740_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
{
- unsigned int gpio = jz4740_pwm_gpio_list[pwm->hwpwm];
-
jz4740_timer_set_ctrl(pwm->hwpwm, 0);
- jz_gpio_set_function(gpio, JZ_GPIO_FUNC_NONE);
- gpio_free(gpio);
-
jz4740_timer_stop(pwm->hwpwm);
}
diff --git a/drivers/video/fbdev/jz4740_fb.c b/drivers/video/fbdev/jz4740_fb.c
index 87790e9..b57df83 100644
--- a/drivers/video/fbdev/jz4740_fb.c
+++ b/drivers/video/fbdev/jz4740_fb.c
@@ -17,6 +17,7 @@
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/platform_device.h>
+#include <linux/pinctrl/consumer.h>
#include <linux/clk.h>
#include <linux/delay.h>
@@ -27,7 +28,6 @@
#include <linux/dma-mapping.h>
#include <asm/mach-jz4740/jz4740_fb.h>
-#include <asm/mach-jz4740/gpio.h>
#define JZ_REG_LCD_CFG 0x00
#define JZ_REG_LCD_VSYNC 0x04
@@ -146,93 +146,6 @@
.accel = FB_ACCEL_NONE,
};
-static const struct jz_gpio_bulk_request jz_lcd_ctrl_pins[] = {
- JZ_GPIO_BULK_PIN(LCD_PCLK),
- JZ_GPIO_BULK_PIN(LCD_HSYNC),
- JZ_GPIO_BULK_PIN(LCD_VSYNC),
- JZ_GPIO_BULK_PIN(LCD_DE),
- JZ_GPIO_BULK_PIN(LCD_PS),
- JZ_GPIO_BULK_PIN(LCD_REV),
- JZ_GPIO_BULK_PIN(LCD_CLS),
- JZ_GPIO_BULK_PIN(LCD_SPL),
-};
-
-static const struct jz_gpio_bulk_request jz_lcd_data_pins[] = {
- JZ_GPIO_BULK_PIN(LCD_DATA0),
- JZ_GPIO_BULK_PIN(LCD_DATA1),
- JZ_GPIO_BULK_PIN(LCD_DATA2),
- JZ_GPIO_BULK_PIN(LCD_DATA3),
- JZ_GPIO_BULK_PIN(LCD_DATA4),
- JZ_GPIO_BULK_PIN(LCD_DATA5),
- JZ_GPIO_BULK_PIN(LCD_DATA6),
- JZ_GPIO_BULK_PIN(LCD_DATA7),
- JZ_GPIO_BULK_PIN(LCD_DATA8),
- JZ_GPIO_BULK_PIN(LCD_DATA9),
- JZ_GPIO_BULK_PIN(LCD_DATA10),
- JZ_GPIO_BULK_PIN(LCD_DATA11),
- JZ_GPIO_BULK_PIN(LCD_DATA12),
- JZ_GPIO_BULK_PIN(LCD_DATA13),
- JZ_GPIO_BULK_PIN(LCD_DATA14),
- JZ_GPIO_BULK_PIN(LCD_DATA15),
- JZ_GPIO_BULK_PIN(LCD_DATA16),
- JZ_GPIO_BULK_PIN(LCD_DATA17),
-};
-
-static unsigned int jzfb_num_ctrl_pins(struct jzfb *jzfb)
-{
- unsigned int num;
-
- switch (jzfb->pdata->lcd_type) {
- case JZ_LCD_TYPE_GENERIC_16_BIT:
- num = 4;
- break;
- case JZ_LCD_TYPE_GENERIC_18_BIT:
- num = 4;
- break;
- case JZ_LCD_TYPE_8BIT_SERIAL:
- num = 3;
- break;
- case JZ_LCD_TYPE_SPECIAL_TFT_1:
- case JZ_LCD_TYPE_SPECIAL_TFT_2:
- case JZ_LCD_TYPE_SPECIAL_TFT_3:
- num = 8;
- break;
- default:
- num = 0;
- break;
- }
- return num;
-}
-
-static unsigned int jzfb_num_data_pins(struct jzfb *jzfb)
-{
- unsigned int num;
-
- switch (jzfb->pdata->lcd_type) {
- case JZ_LCD_TYPE_GENERIC_16_BIT:
- num = 16;
- break;
- case JZ_LCD_TYPE_GENERIC_18_BIT:
- num = 18;
- break;
- case JZ_LCD_TYPE_8BIT_SERIAL:
- num = 8;
- break;
- case JZ_LCD_TYPE_SPECIAL_TFT_1:
- case JZ_LCD_TYPE_SPECIAL_TFT_2:
- case JZ_LCD_TYPE_SPECIAL_TFT_3:
- if (jzfb->pdata->bpp == 18)
- num = 18;
- else
- num = 16;
- break;
- default:
- num = 0;
- break;
- }
- return num;
-}
-
/* Based on CNVT_TOHW macro from skeletonfb.c */
static inline uint32_t jzfb_convert_color_to_hw(unsigned val,
struct fb_bitfield *bf)
@@ -487,8 +400,7 @@
clk_prepare_enable(jzfb->ldclk);
- jz_gpio_bulk_resume(jz_lcd_ctrl_pins, jzfb_num_ctrl_pins(jzfb));
- jz_gpio_bulk_resume(jz_lcd_data_pins, jzfb_num_data_pins(jzfb));
+ pinctrl_pm_select_default_state(&jzfb->pdev->dev);
writel(0, jzfb->base + JZ_REG_LCD_STATE);
@@ -511,8 +423,7 @@
ctrl = readl(jzfb->base + JZ_REG_LCD_STATE);
} while (!(ctrl & JZ_LCD_STATE_DISABLED));
- jz_gpio_bulk_suspend(jz_lcd_ctrl_pins, jzfb_num_ctrl_pins(jzfb));
- jz_gpio_bulk_suspend(jz_lcd_data_pins, jzfb_num_data_pins(jzfb));
+ pinctrl_pm_select_sleep_state(&jzfb->pdev->dev);
clk_disable_unprepare(jzfb->ldclk);
}
@@ -701,9 +612,6 @@
fb->mode = NULL;
jzfb_set_par(fb);
- jz_gpio_bulk_request(jz_lcd_ctrl_pins, jzfb_num_ctrl_pins(jzfb));
- jz_gpio_bulk_request(jz_lcd_data_pins, jzfb_num_data_pins(jzfb));
-
ret = register_framebuffer(fb);
if (ret) {
dev_err(&pdev->dev, "Failed to register framebuffer: %d\n", ret);
@@ -715,9 +623,6 @@
return 0;
err_free_devmem:
- jz_gpio_bulk_free(jz_lcd_ctrl_pins, jzfb_num_ctrl_pins(jzfb));
- jz_gpio_bulk_free(jz_lcd_data_pins, jzfb_num_data_pins(jzfb));
-
fb_dealloc_cmap(&fb->cmap);
jzfb_free_devmem(jzfb);
err_framebuffer_release:
@@ -731,9 +636,6 @@
jzfb_blank(FB_BLANK_POWERDOWN, jzfb->fb);
- jz_gpio_bulk_free(jz_lcd_ctrl_pins, jzfb_num_ctrl_pins(jzfb));
- jz_gpio_bulk_free(jz_lcd_data_pins, jzfb_num_data_pins(jzfb));
-
fb_dealloc_cmap(&jzfb->fb->cmap);
jzfb_free_devmem(jzfb);