blob: 216b1d8a862fcc56999cc3958144908d79c35599 [file] [log] [blame]
#ifndef __LINUX_NL80211_H
#define __LINUX_NL80211_H
/*
* 802.11 netlink interface public header
*
* Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2008 Michael Wu <flamingice@sourmilk.net>
* Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
* Copyright 2008 Michael Buesch <mb@bu3sch.de>
* Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include <linux/types.h>
/**
* DOC: Station handling
*
* Stations are added per interface, but a special case exists with VLAN
* interfaces. When a station is bound to an AP interface, it may be moved
* into a VLAN identified by a VLAN interface index (%NL80211_ATTR_STA_VLAN).
* The station is still assumed to belong to the AP interface it was added
* to.
*
* TODO: need more info?
*/
/**
* DOC: Frame transmission/registration support
*
* Frame transmission and registration support exists to allow userspace
* management entities such as wpa_supplicant react to management frames
* that are not being handled by the kernel. This includes, for example,
* certain classes of action frames that cannot be handled in the kernel
* for various reasons.
*
* Frame registration is done on a per-interface basis and registrations
* cannot be removed other than by closing the socket. It is possible to
* specify a registration filter to register, for example, only for a
* certain type of action frame. In particular with action frames, those
* that userspace registers for will not be returned as unhandled by the
* driver, so that the registered application has to take responsibility
* for doing that.
*
* The type of frame that can be registered for is also dependent on the
* driver and interface type. The frame types are advertised in wiphy
* attributes so applications know what to expect.
*
* NOTE: When an interface changes type while registrations are active,
* these registrations are ignored until the interface type is
* changed again. This means that changing the interface type can
* lead to a situation that couldn't otherwise be produced, but
* any such registrations will be dormant in the sense that they
* will not be serviced, i.e. they will not receive any frames.
*
* Frame transmission allows userspace to send for example the required
* responses to action frames. It is subject to some sanity checking,
* but many frames can be transmitted. When a frame was transmitted, its
* status is indicated to the sending socket.
*
* For more technical details, see the corresponding command descriptions
* below.
*/
/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
*
* @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
* %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
* %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
* %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
* and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
* However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
* instead, the support here is for backward compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
* @NL80211_CMD_DEL_WIPHY: Wiphy deleted. Has attributes
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME.
*
* @NL80211_CMD_GET_INTERFACE: Request an interface's configuration;
* either a dump request on a %NL80211_ATTR_WIPHY or a specific get
* on an %NL80211_ATTR_IFINDEX is supported.
* @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_IFTYPE.
* @NL80211_CMD_NEW_INTERFACE: Newly created virtual interface or response
* to %NL80211_CMD_GET_INTERFACE. Has %NL80211_ATTR_IFINDEX,
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_IFTYPE attributes. Can also
* be sent from userspace to request creation of a new virtual interface,
* then requires attributes %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFTYPE and
* %NL80211_ATTR_IFNAME.
* @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
* userspace to request deletion of a virtual interface, then requires
* attribute %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
* by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
* @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
* %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
* @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
* %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
* and %NL80211_ATTR_KEY_SEQ attributes.
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
* or %NL80211_ATTR_MAC.
*
* @NL80211_CMD_GET_BEACON: retrieve beacon information (returned in a
* %NL80222_CMD_NEW_BEACON message)
* @NL80211_CMD_SET_BEACON: set the beacon on an access point interface
* using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD,
* %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes.
* @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface,
* parameters are like for %NL80211_CMD_SET_BEACON.
* @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it
*
* @NL80211_CMD_GET_STATION: Get station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_STATION: Set station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_STATION: Add a station with given attributes to the
* the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all stations, on the interface identified
* by %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
* %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
* @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
* %NL80211_ATTR_MAC.
* @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
* the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all mesh paths, on the interface identified
* by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
* %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
* regulatory domain.
* @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
* after being queried by the kernel. CRDA replies by sending a regulatory
* domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
* current alpha2 if it found a match. It also provides
* NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
* regulatory rule is a nested set of attributes given by
* %NL80211_ATTR_REG_RULE_FREQ_[START|END] and
* %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
* to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
* interface is identified with %NL80211_ATTR_IFINDEX and the management
* frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be
* added to the end of the specified management frame is specified with
* %NL80211_ATTR_IE. If the command succeeds, the requested data will be
* added to all specified management frames generated by
* kernel/firmware/driver.
* Note: This command has been removed and it is only reserved at this
* point to avoid re-using existing command number. The functionality this
* command was planned for has been provided with cleaner design with the
* option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN,
* NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE,
* NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE.
*
* @NL80211_CMD_GET_SCAN: get scan results
* @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
* @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
* NL80211_CMD_GET_SCAN and on the "scan" multicast group)
* @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
* partial scan results may be available
*
* @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
* or noise level
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
*
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
* has been changed and provides details of the request information
* that caused the change such as who initiated the regulatory request
* (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx
* (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if
* the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or
* %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain
* set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
* %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on
* to (%NL80211_ATTR_REG_ALPHA2).
* @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon
* has been found while world roaming thus enabling active scan or
* any mode of operation that initiates TX (beacons) on a channel
* where we would not have been able to do either before. As an example
* if you are world roaming (regulatory domain set to world or if your
* driver is using a custom world roaming regulatory domain) and while
* doing a passive scan on the 5 GHz band you find an AP there (if not
* on a DFS channel) you will now be able to actively scan for that AP
* or use AP mode on your card on that same channel. Note that this will
* never be used for channels 1-11 on the 2 GHz band as they are always
* enabled world wide. This beacon hint is only sent if your device had
* either disabled active scanning or beaconing on a channel. We send to
* userspace the wiphy on which we removed a restriction from
* (%NL80211_ATTR_WIPHY) and the channel on which this occurred
* before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER)
* the beacon hint was processed.
*
* @NL80211_CMD_AUTHENTICATE: authentication request and notification.
* This command is used both as a command (request to authenticate) and
* as an event on the "mlme" multicast group indicating completion of the
* authentication process.
* When used as a command, %NL80211_ATTR_IFINDEX is used to identify the
* interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
* BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
* the SSID (mainly for association, but is included in authentication
* request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
* to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
* is used to specify the authentication type. %NL80211_ATTR_IE is used to
* define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
* to be added to the frame.
* When used as an event, this reports reception of an Authentication
* frame in station and IBSS modes when the local MLME processed the
* frame, i.e., it was for the local STA and was received in correct
* state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
* MLME SAP interface (kernel providing MLME, userspace SME). The
* included %NL80211_ATTR_FRAME attribute contains the management frame
* (including both the header and frame body, but not FCS). This event is
* also used to indicate if the authentication attempt timed out. In that
* case the %NL80211_ATTR_FRAME attribute is replaced with a
* %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which
* pending authentication timed out).
* @NL80211_CMD_ASSOCIATE: association request and notification; like
* NL80211_CMD_AUTHENTICATE but for Association and Reassociation
* (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
* MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives).
* @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like
* NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to
* MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
* primitives).
* @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like
* NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to
* MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
*
* @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael
* MIC (part of TKIP) failure; sent on the "mlme" multicast group; the
* event includes %NL80211_ATTR_MAC to describe the source MAC address of
* the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key
* type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and
* %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this
* event matches with MLME-MICHAELMICFAILURE.indication() primitive
*
* @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
* FREQ attribute (for the initial frequency if no peer can be found)
* and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
* should be fixed rather than automatically determined. Can only be
* executed on a network interface that is UP, and fixed BSSID/FREQ
* may be rejected. Another optional parameter is the beacon interval,
* given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
* given defaults to 100 TU (102.4ms).
* @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
* determined by the network interface.
*
* @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
* to identify the device, and the TESTDATA blob attribute to pass through
* to the driver.
*
* @NL80211_CMD_CONNECT: connection request and notification; this command
* requests to connect to a specified network but without separating
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
* IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
* %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
* determined by the STATUS_CODE attribute.
* @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
* sent as an event when the card/driver roamed by itself.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
* userspace that a connection was dropped by the AP or due to other
* reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
* %NL80211_ATTR_REASON_CODE attributes are used.
*
* @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
* associated with this wiphy must be down and will follow.
*
* @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
* channel for the specified amount of time. This can be used to do
* off-channel operations like transmit a Public Action frame and wait for
* a response while being associated to an AP on another channel.
* %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
* radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
* frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
* optionally used to specify additional channel parameters.
* %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
* to remain on the channel. This command is also used as an event to
* notify when the requested duration starts (it may take a while for the
* driver to schedule this time due to other concurrent needs for the
* radio).
* When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
* that will be included with any events pertaining to this request;
* the cookie is also used to cancel the request.
* @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
* pending remain-on-channel duration if the desired operation has been
* completed prior to expiration of the originally requested duration.
* %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
* radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
* uniquely identify the request.
* This command is also used as an event to notify when a requested
* remain-on-channel duration has expired.
*
* @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
* rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
* and @NL80211_ATTR_TX_RATES the set of allowed rates.
*
* @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
* (via @NL80211_CMD_FRAME) for processing in userspace. This command
* requires an interface index, a frame type attribute (optional for
* backward compatibility reasons, if not given assumes action frames)
* and a match attribute containing the first few bytes of the frame
* that should match, e.g. a single byte for only a category match or
* four bytes for vendor frames including the OUI. The registration
* cannot be dropped, but is removed automatically when the netlink
* socket is closed. Multiple registrations can be made.
* @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
* backward compatibility
* @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
* command is used both as a request to transmit a management frame and
* as an event indicating reception of a frame that was not processed in
* kernel code, but is for us (i.e., which may need to be processed in a
* user space application). %NL80211_ATTR_FRAME is used to specify the
* frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
* optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
* which channel the frame is to be transmitted or was received. If this
* channel is not the current channel (remain-on-channel or the
* operational channel) the device will switch to the given channel and
* transmit the frame, optionally waiting for a response for the time
* specified using %NL80211_ATTR_DURATION. When called, this operation
* returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
* TX status event pertaining to the TX request.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary.
* @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
* @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
* transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
* the TX command and %NL80211_ATTR_FRAME includes the contents of the
* frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
* the frame.
* @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
* backward compatibility.
* @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
* is used to configure connection quality monitoring notification trigger
* levels.
* @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
* command is used as an event to indicate the that a trigger level was
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
* and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
* by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
* no other interfaces are operating to avoid disturbing the operation
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
* @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
*
* @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
* mesh config parameters may be given.
* @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
* network is determined by the network interface.
*
* @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame
* notification. This event is used to indicate that an unprotected
* deauthentication frame was dropped when MFP is in use.
* @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame
* notification. This event is used to indicate that an unprotected
* disassociation frame was dropped when MFP is in use.
*
* @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
* beacon or probe response from a compatible mesh peer. This is only
* sent while no station information (sta_info) exists for the new peer
* candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On
* reception of this notification, userspace may decide to create a new
* station (@NL80211_CMD_NEW_STATION). To stop this notification from
* reoccurring, the userspace authentication daemon may want to create the
* new station with the AUTHENTICATED flag unset and maybe change it later
* depending on the authentication result.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
enum nl80211_commands {
/* don't change the order or add anything between, this is ABI! */
NL80211_CMD_UNSPEC,
NL80211_CMD_GET_WIPHY, /* can dump */
NL80211_CMD_SET_WIPHY,
NL80211_CMD_NEW_WIPHY,
NL80211_CMD_DEL_WIPHY,
NL80211_CMD_GET_INTERFACE, /* can dump */
NL80211_CMD_SET_INTERFACE,
NL80211_CMD_NEW_INTERFACE,
NL80211_CMD_DEL_INTERFACE,
NL80211_CMD_GET_KEY,
NL80211_CMD_SET_KEY,
NL80211_CMD_NEW_KEY,
NL80211_CMD_DEL_KEY,
NL80211_CMD_GET_BEACON,
NL80211_CMD_SET_BEACON,
NL80211_CMD_NEW_BEACON,
NL80211_CMD_DEL_BEACON,
NL80211_CMD_GET_STATION,
NL80211_CMD_SET_STATION,
NL80211_CMD_NEW_STATION,
NL80211_CMD_DEL_STATION,
NL80211_CMD_GET_MPATH,
NL80211_CMD_SET_MPATH,
NL80211_CMD_NEW_MPATH,
NL80211_CMD_DEL_MPATH,
NL80211_CMD_SET_BSS,
NL80211_CMD_SET_REG,
NL80211_CMD_REQ_SET_REG,
NL80211_CMD_GET_MESH_CONFIG,
NL80211_CMD_SET_MESH_CONFIG,
NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
NL80211_CMD_GET_REG,
NL80211_CMD_GET_SCAN,
NL80211_CMD_TRIGGER_SCAN,
NL80211_CMD_NEW_SCAN_RESULTS,
NL80211_CMD_SCAN_ABORTED,
NL80211_CMD_REG_CHANGE,
NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE,
NL80211_CMD_DEAUTHENTICATE,
NL80211_CMD_DISASSOCIATE,
NL80211_CMD_MICHAEL_MIC_FAILURE,
NL80211_CMD_REG_BEACON_HINT,
NL80211_CMD_JOIN_IBSS,
NL80211_CMD_LEAVE_IBSS,
NL80211_CMD_TESTMODE,
NL80211_CMD_CONNECT,
NL80211_CMD_ROAM,
NL80211_CMD_DISCONNECT,
NL80211_CMD_SET_WIPHY_NETNS,
NL80211_CMD_GET_SURVEY,
NL80211_CMD_NEW_SURVEY_RESULTS,
NL80211_CMD_SET_PMKSA,
NL80211_CMD_DEL_PMKSA,
NL80211_CMD_FLUSH_PMKSA,
NL80211_CMD_REMAIN_ON_CHANNEL,
NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL,
NL80211_CMD_SET_TX_BITRATE_MASK,
NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_FRAME,
NL80211_CMD_ACTION = NL80211_CMD_FRAME,
NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_SET_POWER_SAVE,
NL80211_CMD_GET_POWER_SAVE,
NL80211_CMD_SET_CQM,
NL80211_CMD_NOTIFY_CQM,
NL80211_CMD_SET_CHANNEL,
NL80211_CMD_SET_WDS_PEER,
NL80211_CMD_FRAME_WAIT_CANCEL,
NL80211_CMD_JOIN_MESH,
NL80211_CMD_LEAVE_MESH,
NL80211_CMD_UNPROT_DEAUTHENTICATE,
NL80211_CMD_UNPROT_DISASSOCIATE,
NL80211_CMD_NEW_PEER_CANDIDATE,
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
__NL80211_CMD_AFTER_LAST,
NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
};
/*
* Allow user space programs to use #ifdef on new commands by defining them
* here
*/
#define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
#define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE
#define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE
#define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE
#define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE
#define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE
#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
/* source-level API compatibility */
#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
/**
* enum nl80211_attrs - nl80211 netlink attributes
*
* @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
*
* @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf.
* /sys/class/ieee80211/<phyname>/index
* @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
* @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
* @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz
* @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
* if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included):
* NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
* this attribute)
* NL80211_CHAN_HT20 = HT20 only
* NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
* NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
* @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
* less than or equal to the RTS threshold; allowed range: 1..255;
* dot11ShortRetryLimit; u8
* @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is
* greater than the RTS threshold; allowed range: 1..255;
* dot11ShortLongLimit; u8
* @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum
* length in octets for frames; allowed range: 256..8000, disable
* fragmentation with (u32)-1; dot11FragmentationThreshold; u32
* @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length
* larger than or equal to this use RTS/CTS handshake); allowed range:
* 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
* @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11
* section 7.3.2.9; dot11CoverageClass; u8
*
* @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
* @NL80211_ATTR_IFNAME: network interface name
* @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
*
* @NL80211_ATTR_MAC: MAC address (various uses)
*
* @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of
* 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
* keys
* @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3)
* @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
*
* @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU
* @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing
* @NL80211_ATTR_BEACON_HEAD: portion of the beacon before the TIM IE
* @NL80211_ATTR_BEACON_TAIL: portion of the beacon after the TIM IE
*
* @NL80211_ATTR_STA_AID: Association ID for the station (u16)
* @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of
* &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2)
* @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by
* IEEE 802.11 7.3.1.6 (u16).
* @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported
* rates as defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
* @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
* to, or the AP interface the station was originally added to to.
* @NL80211_ATTR_STA_INFO: information about a station, part of station info
* given for %NL80211_CMD_GET_STATION, nested attribute containing
* info as possible, see &enum nl80211_sta_info.
*
* @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands,
* consisting of a nested array.
*
* @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
* @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link.
* @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
* @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
* info given for %NL80211_CMD_GET_MPATH, nested attribute described at
* &enum nl80211_mpath_info.
*
* @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of
* &enum nl80211_mntr_flags.
*
* @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the
* current regulatory domain should be set to or is already set to.
* For example, 'CR', for Costa Rica. This attribute is used by the kernel
* to query the CRDA to retrieve one regulatory domain. This attribute can
* also be used by userspace to query the kernel for the currently set
* regulatory domain. We chose an alpha2 as that is also used by the
* IEEE-802.11d country information element to identify a country.
* Users can also simply ask the wireless core to set regulatory domain
* to a specific alpha2.
* @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory
* rules.
*
* @NL80211_ATTR_BSS_CTS_PROT: whether CTS protection is enabled (u8, 0 or 1)
* @NL80211_ATTR_BSS_SHORT_PREAMBLE: whether short preamble is enabled
* (u8, 0 or 1)
* @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled
* (u8, 0 or 1)
* @NL80211_ATTR_BSS_BASIC_RATES: basic rates, array of basic
* rates in format defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
*
* @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION)
*
* @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all
* supported interface types, each a flag attribute with the number
* of the interface mode.
*
* @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for
* %NL80211_CMD_SET_MGMT_EXTRA_IE.
*
* @NL80211_ATTR_IE: Information element(s) data (used, e.g., with
* %NL80211_CMD_SET_MGMT_EXTRA_IE).
*
* @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with
* a single scan request, a wiphy attribute.
* @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements
* that can be added to a scan request
*
* @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
* @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
* scanning and include a zero-length SSID (wildcard) for wildcard scan
* @NL80211_ATTR_BSS: scan result BSS
*
* @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain
* currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_*
* @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently
* set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*)
*
* @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies
* an array of command numbers (i.e. a mapping index to command number)
* that the driver for the given wiphy supports.
*
* @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header
* and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and
* NL80211_CMD_ASSOCIATE events
* @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets)
* @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type,
* represented as a u32
* @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and
* %NL80211_CMD_DISASSOCIATE, u16
*
* @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as
* a u32
*
* @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change
* due to considerations from a beacon hint. This attribute reflects
* the state of the channel _before_ the beacon hint processing. This
* attributes consists of a nested attribute containing
* NL80211_FREQUENCY_ATTR_*
* @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change
* due to considerations from a beacon hint. This attribute reflects
* the state of the channel _after_ the beacon hint processing. This
* attributes consists of a nested attribute containing
* NL80211_FREQUENCY_ATTR_*
*
* @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported
* cipher suites
*
* @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look
* for other networks on different channels
*
* @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this
* is used, e.g., with %NL80211_CMD_AUTHENTICATE event
*
* @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is
* used for the association (&enum nl80211_mfp, represented as a u32);
* this attribute can be used
* with %NL80211_CMD_ASSOCIATE request
*
* @NL80211_ATTR_STA_FLAGS2: Attribute containing a
* &struct nl80211_sta_flag_update.
*
* @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls
* IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in
* station mode. If the flag is included in %NL80211_CMD_ASSOCIATE
* request, the driver will assume that the port is unauthorized until
* authorized by user space. Otherwise, port is marked authorized by
* default in station mode.
* @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
* ethertype that will be used for key negotiation. It can be
* specified with the associate and connect commands. If it is not
* specified, the value defaults to 0x888E (PAE, 802.1X). This
* attribute is also used as a flag in the wiphy information to
* indicate that protocols other than PAE are supported.
* @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
* ethertype frames used for key negotiation must not be encrypted.
*
* @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
* We recommend using nested, driver-specific attributes within this.
*
* @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT
* event was due to the AP disconnecting the station, and not due to
* a local disconnect request.
* @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT
* event (u16)
* @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
* that protected APs should be used.
*
* @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT and ASSOCIATE to
* indicate which unicast key ciphers will be used with the connection
* (an array of u32).
* @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT and ASSOCIATE to indicate
* which group key cipher will be used with the connection (a u32).
* @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT and ASSOCIATE to indicate
* which WPA version(s) the AP we want to associate with is using
* (a u32 with flags from &enum nl80211_wpa_versions).
* @NL80211_ATTR_AKM_SUITES: Used with CONNECT and ASSOCIATE to indicate
* which key management algorithm(s) to use (an array of u32).
*
* @NL80211_ATTR_REQ_IE: (Re)association request information elements as
* sent out by the card, for ROAM and successful CONNECT events.
* @NL80211_ATTR_RESP_IE: (Re)association response information elements as
* sent by peer, for ROAM and successful CONNECT events.
*
* @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used by in ASSOCIATE
* commands to specify using a reassociate frame
*
* @NL80211_ATTR_KEY: key information in a nested attribute with
* %NL80211_KEY_* sub-attributes
* @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect()
* and join_ibss(), key information is in a nested attribute each
* with %NL80211_KEY_* sub-attributes
*
* @NL80211_ATTR_PID: Process ID of a network namespace.
*
* @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for
* dumps. This number increases whenever the object list being
* dumped changes, and as such userspace can verify that it has
* obtained a complete and consistent snapshot by verifying that
* all dump messages contain the same generation number. If it
* changed then the list changed and the dump should be repeated
* completely from scratch.
*
* @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface
*
* @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of
* the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
* containing info as possible, see &enum survey_info.
*
* @NL80211_ATTR_PMKID: PMK material for PMKSA caching.
* @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can
* cache, a wiphy attribute.
*
* @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
* @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
* specifies the maximum duration that can be requested with the
* remain-on-channel operation, in milliseconds, u32.
*
* @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
*
* @NL80211_ATTR_TX_RATES: Nested set of attributes
* (enum nl80211_tx_rate_attributes) describing TX rates per band. The
* enum nl80211_band value is used as the index (nla_type() of the nested
* data. If a band is not included, it will be configured to allow all
* rates based on negotiated supported rates information. This attribute
* is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
*
* @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
* at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
* @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
* @NL80211_CMD_REGISTER_FRAME command.
* @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
* nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
* information about which frame types can be transmitted with
* %NL80211_CMD_FRAME.
* @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
* nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
* information about which frame types can be registered for RX.
*
* @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
* acknowledged by the recipient.
*
* @NL80211_ATTR_CQM: connection quality monitor configuration in a
* nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
*
* @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
* is requesting a local authentication/association state change without
* invoking actual management frame exchange. This can be used with
* NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
* NL80211_CMD_DISASSOCIATE.
*
* @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
* connected to this BSS.
*
* @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
* &enum nl80211_tx_power_setting for possible values.
* @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
* This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
* for non-automatic settings.
*
* @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
* means support for per-station GTKs.
*
* @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
* This can be used to mask out antennas which are not attached or should
* not be used for transmitting. If an antenna is not selected in this
* bitmap the hardware is not allowed to transmit on this antenna.
*
* Each bit represents one antenna, starting with antenna 1 at the first
* bit. Depending on which antennas are selected in the bitmap, 802.11n
* drivers can derive which chainmasks to use (if all antennas belonging to
* a particular chain are disabled this chain should be disabled) and if
* a chain has diversity antennas wether diversity should be used or not.
* HT capabilities (STBC, TX Beamforming, Antenna selection) can be
* derived from the available chains after applying the antenna mask.
* Non-802.11n drivers can derive wether to use diversity or not.
* Drivers may reject configurations or RX/TX mask combinations they cannot
* support by returning -EINVAL.
*
* @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
* This can be used to mask out antennas which are not attached or should
* not be used for receiving. If an antenna is not selected in this bitmap
* the hardware should not be configured to receive on this antenna.
* For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX.
*
* @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available
* for configuration as TX antennas via the above parameters.
*
* @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available
* for configuration as RX antennas via the above parameters.
*
* @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
*
* @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be
* transmitted on another channel when the channel given doesn't match
* the current channel. If the current channel doesn't match and this
* flag isn't set, the frame will be rejected. This is also used as an
* nl80211 capability flag.
*
* @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16)
*
* @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
*
* @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be
* changed once the mesh is active.
* @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
* containing attributes from &enum nl80211_meshconf_params.
* @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
* allows auth frames in a mesh to be passed to userspace for processing via
* the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
*
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
enum nl80211_attrs {
/* don't change the order or add anything between, this is ABI! */
NL80211_ATTR_UNSPEC,
NL80211_ATTR_WIPHY,
NL80211_ATTR_WIPHY_NAME,
NL80211_ATTR_IFINDEX,
NL80211_ATTR_IFNAME,
NL80211_ATTR_IFTYPE,
NL80211_ATTR_MAC,
NL80211_ATTR_KEY_DATA,
NL80211_ATTR_KEY_IDX,
NL80211_ATTR_KEY_CIPHER,
NL80211_ATTR_KEY_SEQ,
NL80211_ATTR_KEY_DEFAULT,
NL80211_ATTR_BEACON_INTERVAL,
NL80211_ATTR_DTIM_PERIOD,
NL80211_ATTR_BEACON_HEAD,
NL80211_ATTR_BEACON_TAIL,
NL80211_ATTR_STA_AID,
NL80211_ATTR_STA_FLAGS,
NL80211_ATTR_STA_LISTEN_INTERVAL,
NL80211_ATTR_STA_SUPPORTED_RATES,
NL80211_ATTR_STA_VLAN,
NL80211_ATTR_STA_INFO,
NL80211_ATTR_WIPHY_BANDS,
NL80211_ATTR_MNTR_FLAGS,
NL80211_ATTR_MESH_ID,
NL80211_ATTR_STA_PLINK_ACTION,
NL80211_ATTR_MPATH_NEXT_HOP,
NL80211_ATTR_MPATH_INFO,
NL80211_ATTR_BSS_CTS_PROT,
NL80211_ATTR_BSS_SHORT_PREAMBLE,
NL80211_ATTR_BSS_SHORT_SLOT_TIME,
NL80211_ATTR_HT_CAPABILITY,
NL80211_ATTR_SUPPORTED_IFTYPES,
NL80211_ATTR_REG_ALPHA2,
NL80211_ATTR_REG_RULES,
NL80211_ATTR_MESH_CONFIG,
NL80211_ATTR_BSS_BASIC_RATES,
NL80211_ATTR_WIPHY_TXQ_PARAMS,
NL80211_ATTR_WIPHY_FREQ,
NL80211_ATTR_WIPHY_CHANNEL_TYPE,
NL80211_ATTR_KEY_DEFAULT_MGMT,
NL80211_ATTR_MGMT_SUBTYPE,
NL80211_ATTR_IE,
NL80211_ATTR_MAX_NUM_SCAN_SSIDS,
NL80211_ATTR_SCAN_FREQUENCIES,
NL80211_ATTR_SCAN_SSIDS,
NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */
NL80211_ATTR_BSS,
NL80211_ATTR_REG_INITIATOR,
NL80211_ATTR_REG_TYPE,
NL80211_ATTR_SUPPORTED_COMMANDS,
NL80211_ATTR_FRAME,
NL80211_ATTR_SSID,
NL80211_ATTR_AUTH_TYPE,
NL80211_ATTR_REASON_CODE,
NL80211_ATTR_KEY_TYPE,
NL80211_ATTR_MAX_SCAN_IE_LEN,
NL80211_ATTR_CIPHER_SUITES,
NL80211_ATTR_FREQ_BEFORE,
NL80211_ATTR_FREQ_AFTER,
NL80211_ATTR_FREQ_FIXED,
NL80211_ATTR_WIPHY_RETRY_SHORT,
NL80211_ATTR_WIPHY_RETRY_LONG,
NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
NL80211_ATTR_WIPHY_RTS_THRESHOLD,
NL80211_ATTR_TIMED_OUT,
NL80211_ATTR_USE_MFP,
NL80211_ATTR_STA_FLAGS2,
NL80211_ATTR_CONTROL_PORT,
NL80211_ATTR_TESTDATA,
NL80211_ATTR_PRIVACY,
NL80211_ATTR_DISCONNECTED_BY_AP,
NL80211_ATTR_STATUS_CODE,
NL80211_ATTR_CIPHER_SUITES_PAIRWISE,
NL80211_ATTR_CIPHER_SUITE_GROUP,
NL80211_ATTR_WPA_VERSIONS,
NL80211_ATTR_AKM_SUITES,
NL80211_ATTR_REQ_IE,
NL80211_ATTR_RESP_IE,
NL80211_ATTR_PREV_BSSID,
NL80211_ATTR_KEY,
NL80211_ATTR_KEYS,
NL80211_ATTR_PID,
NL80211_ATTR_4ADDR,
NL80211_ATTR_SURVEY_INFO,
NL80211_ATTR_PMKID,
NL80211_ATTR_MAX_NUM_PMKIDS,
NL80211_ATTR_DURATION,
NL80211_ATTR_COOKIE,
NL80211_ATTR_WIPHY_COVERAGE_CLASS,
NL80211_ATTR_TX_RATES,
NL80211_ATTR_FRAME_MATCH,
NL80211_ATTR_ACK,
NL80211_ATTR_PS_STATE,
NL80211_ATTR_CQM,
NL80211_ATTR_LOCAL_STATE_CHANGE,
NL80211_ATTR_AP_ISOLATE,
NL80211_ATTR_WIPHY_TX_POWER_SETTING,
NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
NL80211_ATTR_TX_FRAME_TYPES,
NL80211_ATTR_RX_FRAME_TYPES,
NL80211_ATTR_FRAME_TYPE,
NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
NL80211_ATTR_SUPPORT_IBSS_RSN,
NL80211_ATTR_WIPHY_ANTENNA_TX,
NL80211_ATTR_WIPHY_ANTENNA_RX,
NL80211_ATTR_MCAST_RATE,
NL80211_ATTR_OFFCHANNEL_TX_OK,
NL80211_ATTR_BSS_HT_OPMODE,
NL80211_ATTR_KEY_DEFAULT_TYPES,
NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
NL80211_ATTR_MESH_SETUP,
NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
NL80211_ATTR_SUPPORT_MESH_AUTH,
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
};
/* source-level API compatibility */
#define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
/*
* Allow user space programs to use #ifdef on new attributes by defining them
* here
*/
#define NL80211_CMD_CONNECT NL80211_CMD_CONNECT
#define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY
#define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES
#define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS
#define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ
#define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE
#define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE
#define NL80211_ATTR_IE NL80211_ATTR_IE
#define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR
#define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE
#define NL80211_ATTR_FRAME NL80211_ATTR_FRAME
#define NL80211_ATTR_SSID NL80211_ATTR_SSID
#define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE
#define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE
#define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE
#define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP
#define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS
#define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES
#define NL80211_ATTR_KEY NL80211_ATTR_KEY
#define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
#define NL80211_MAX_SUPP_RATES 32
#define NL80211_MAX_SUPP_REG_RULES 32
#define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
#define NL80211_HT_CAPABILITY_LEN 26
#define NL80211_MAX_NR_CIPHER_SUITES 5
#define NL80211_MAX_NR_AKM_SUITES 2
/**
* enum nl80211_iftype - (virtual) interface types
*
* @NL80211_IFTYPE_UNSPECIFIED: unspecified type, driver decides
* @NL80211_IFTYPE_ADHOC: independent BSS member
* @NL80211_IFTYPE_STATION: managed BSS member
* @NL80211_IFTYPE_AP: access point
* @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points
* @NL80211_IFTYPE_WDS: wireless distribution interface
* @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
* @NL80211_IFTYPE_MESH_POINT: mesh point
* @NL80211_IFTYPE_P2P_CLIENT: P2P client
* @NL80211_IFTYPE_P2P_GO: P2P group owner
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
* @NUM_NL80211_IFTYPES: number of defined interface types
*
* These values are used with the %NL80211_ATTR_IFTYPE
* to set the type of an interface.
*
*/
enum nl80211_iftype {
NL80211_IFTYPE_UNSPECIFIED,
NL80211_IFTYPE_ADHOC,
NL80211_IFTYPE_STATION,
NL80211_IFTYPE_AP,
NL80211_IFTYPE_AP_VLAN,
NL80211_IFTYPE_WDS,
NL80211_IFTYPE_MONITOR,
NL80211_IFTYPE_MESH_POINT,
NL80211_IFTYPE_P2P_CLIENT,
NL80211_IFTYPE_P2P_GO,
/* keep last */
NUM_NL80211_IFTYPES,
NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
};
/**
* enum nl80211_sta_flags - station flags
*
* Station flags. When a station is added to an AP interface, it is
* assumed to be already associated (and hence authenticated.)
*
* @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
* @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
* @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
* with short barker preamble
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
* @NL80211_STA_FLAG_MFP: station uses management frame protection
* @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
enum nl80211_sta_flags {
__NL80211_STA_FLAG_INVALID,
NL80211_STA_FLAG_AUTHORIZED,
NL80211_STA_FLAG_SHORT_PREAMBLE,
NL80211_STA_FLAG_WME,
NL80211_STA_FLAG_MFP,
NL80211_STA_FLAG_AUTHENTICATED,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1
};
/**
* struct nl80211_sta_flag_update - station flags mask/set
* @mask: mask of station flags to set
* @set: which values to set them to
*
* Both mask and set contain bits as per &enum nl80211_sta_flags.
*/
struct nl80211_sta_flag_update {
__u32 mask;
__u32 set;
} __attribute__((packed));
/**
* enum nl80211_rate_info - bitrate information
*
* These attribute types are used with %NL80211_STA_INFO_TXRATE
* when getting information about the bitrate of a station.
*
* @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
* @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
* @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
* @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate
* @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
* @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
__NL80211_RATE_INFO_INVALID,
NL80211_RATE_INFO_BITRATE,
NL80211_RATE_INFO_MCS,
NL80211_RATE_INFO_40_MHZ_WIDTH,
NL80211_RATE_INFO_SHORT_GI,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_sta_bss_param - BSS information collected by STA
*
* These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
* when getting information about the bitrate of a station.
*
* @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
* @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
* @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled
* (flag)
* @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled
* (flag)
* @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
* @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
* @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
* @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
*/
enum nl80211_sta_bss_param {
__NL80211_STA_BSS_PARAM_INVALID,
NL80211_STA_BSS_PARAM_CTS_PROT,
NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
NL80211_STA_BSS_PARAM_DTIM_PERIOD,
NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
/* keep last */
__NL80211_STA_BSS_PARAM_AFTER_LAST,
NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
};
/**
* enum nl80211_sta_info - station information
*
* These attribute types are used with %NL80211_ATTR_STA_INFO
* when getting information about a station.
*
* @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved
* @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
* @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
* @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
* @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
* @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
* containing info as possible, see &enum nl80211_rate_info
* @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
* @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
* station)
* @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
* @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
* @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
* @NL80211_STA_INFO_LLID: the station's mesh LLID
* @NL80211_STA_INFO_PLID: the station's mesh PLID
* @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
* @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
* attribute, like NL80211_STA_INFO_TX_BITRATE.
* @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
* containing info as possible, see &enum nl80211_sta_bss_param
* @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
enum nl80211_sta_info {
__NL80211_STA_INFO_INVALID,
NL80211_STA_INFO_INACTIVE_TIME,
NL80211_STA_INFO_RX_BYTES,
NL80211_STA_INFO_TX_BYTES,
NL80211_STA_INFO_LLID,
NL80211_STA_INFO_PLID,
NL80211_STA_INFO_PLINK_STATE,
NL80211_STA_INFO_SIGNAL,
NL80211_STA_INFO_TX_BITRATE,
NL80211_STA_INFO_RX_PACKETS,
NL80211_STA_INFO_TX_PACKETS,
NL80211_STA_INFO_TX_RETRIES,
NL80211_STA_INFO_TX_FAILED,
NL80211_STA_INFO_SIGNAL_AVG,
NL80211_STA_INFO_RX_BITRATE,
NL80211_STA_INFO_BSS_PARAM,
NL80211_STA_INFO_CONNECTED_TIME,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_mpath_flags - nl80211 mesh path flags
*
* @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active
* @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running
* @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN
* @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
* @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded
*/
enum nl80211_mpath_flags {
NL80211_MPATH_FLAG_ACTIVE = 1<<0,
NL80211_MPATH_FLAG_RESOLVING = 1<<1,
NL80211_MPATH_FLAG_SN_VALID = 1<<2,
NL80211_MPATH_FLAG_FIXED = 1<<3,
NL80211_MPATH_FLAG_RESOLVED = 1<<4,
};
/**
* enum nl80211_mpath_info - mesh path information
*
* These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting
* information about a mesh path.
*
* @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
* @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
* @NL80211_MPATH_INFO_SN: destination sequence number
* @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
* @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
* @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
* &enum nl80211_mpath_flags;
* @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
* @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
* @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
* currently defind
* @__NL80211_MPATH_INFO_AFTER_LAST: internal use
*/
enum nl80211_mpath_info {
__NL80211_MPATH_INFO_INVALID,
NL80211_MPATH_INFO_FRAME_QLEN,
NL80211_MPATH_INFO_SN,
NL80211_MPATH_INFO_METRIC,
NL80211_MPATH_INFO_EXPTIME,
NL80211_MPATH_INFO_FLAGS,
NL80211_MPATH_INFO_DISCOVERY_TIMEOUT,
NL80211_MPATH_INFO_DISCOVERY_RETRIES,
/* keep last */
__NL80211_MPATH_INFO_AFTER_LAST,
NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_band_attr - band attributes
* @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BAND_ATTR_FREQS: supported frequencies in this band,
* an array of nested frequency attributes
* @NL80211_BAND_ATTR_RATES: supported bitrates in this band,
* an array of nested bitrate attributes
* @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as
* defined in 802.11n
* @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
* @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
enum nl80211_band_attr {
__NL80211_BAND_ATTR_INVALID,
NL80211_BAND_ATTR_FREQS,
NL80211_BAND_ATTR_RATES,
NL80211_BAND_ATTR_HT_MCS_SET,
NL80211_BAND_ATTR_HT_CAPA,
NL80211_BAND_ATTR_HT_AMPDU_FACTOR,
NL80211_BAND_ATTR_HT_AMPDU_DENSITY,
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
};
#define NL80211_BAND_ATTR_HT_CAPA NL80211_BAND_ATTR_HT_CAPA
/**
* enum nl80211_frequency_attr - frequency attributes
* @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
* @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
* regulatory domain.
* @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is
* permitted on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
* (100 * dBm).
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
NL80211_FREQUENCY_ATTR_FREQ,
NL80211_FREQUENCY_ATTR_DISABLED,
NL80211_FREQUENCY_ATTR_PASSIVE_SCAN,
NL80211_FREQUENCY_ATTR_NO_IBSS,
NL80211_FREQUENCY_ATTR_RADAR,
NL80211_FREQUENCY_ATTR_MAX_TX_POWER,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1
};
#define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER
/**
* enum nl80211_bitrate_attr - bitrate attributes
* @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
* @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
* in 2.4 GHz band.
* @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
* currently defined
* @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_bitrate_attr {
__NL80211_BITRATE_ATTR_INVALID,
NL80211_BITRATE_ATTR_RATE,
NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE,
/* keep last */
__NL80211_BITRATE_ATTR_AFTER_LAST,
NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_initiator - Indicates the initiator of a reg domain request
* @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world
* regulatory domain.
* @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the
* regulatory domain.
* @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the
* wireless core it thinks its knows the regulatory domain we should be in.
* @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
* 802.11 country information element with regulatory information it
* thinks we should consider. cfg80211 only processes the country
* code from the IE, and relies on the regulatory domain information
* structure passed by userspace (CRDA) from our wireless-regdb.
* If a channel is enabled but the country code indicates it should
* be disabled we disable the channel and re-enable it upon disassociation.
*/
enum nl80211_reg_initiator {
NL80211_REGDOM_SET_BY_CORE,
NL80211_REGDOM_SET_BY_USER,
NL80211_REGDOM_SET_BY_DRIVER,
NL80211_REGDOM_SET_BY_COUNTRY_IE,
};
/**
* enum nl80211_reg_type - specifies the type of regulatory domain
* @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains
* to a specific country. When this is set you can count on the
* ISO / IEC 3166 alpha2 country code being valid.
* @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory
* domain.
* @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom
* driver specific world regulatory domain. These do not apply system-wide
* and are only applicable to the individual devices which have requested
* them to be applied.
* @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product
* of an intersection between two regulatory domains -- the previously
* set regulatory domain on the system and the last accepted regulatory
* domain request to be processed.
*/
enum nl80211_reg_type {
NL80211_REGDOM_TYPE_COUNTRY,
NL80211_REGDOM_TYPE_WORLD,
NL80211_REGDOM_TYPE_CUSTOM_WORLD,
NL80211_REGDOM_TYPE_INTERSECTION,
};
/**
* enum nl80211_reg_rule_attr - regulatory rule attributes
* @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
* considerations for a given frequency range. These are the
* &enum nl80211_reg_rule_flags.
* @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory
* rule in KHz. This is not a center of frequency but an actual regulatory
* band edge.
* @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule
* in KHz. This is not a center a frequency but an actual regulatory
* band edge.
* @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this
* frequency range, in KHz.
* @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain
* for a given frequency range. The value is in mBi (100 * dBi).
* If you don't have one then don't send this.
* @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
* a given frequency range. The value is in mBm (100 * dBm).
* @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
* currently defined
* @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
*/
enum nl80211_reg_rule_attr {
__NL80211_REG_RULE_ATTR_INVALID,
NL80211_ATTR_REG_RULE_FLAGS,
NL80211_ATTR_FREQ_RANGE_START,
NL80211_ATTR_FREQ_RANGE_END,
NL80211_ATTR_FREQ_RANGE_MAX_BW,
NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN,
NL80211_ATTR_POWER_RULE_MAX_EIRP,
/* keep last */
__NL80211_REG_RULE_ATTR_AFTER_LAST,
NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_reg_rule_flags - regulatory rule flags
*
* @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
* @NL80211_RRF_NO_CCK: CCK modulation not allowed
* @NL80211_RRF_NO_INDOOR: indoor operation not allowed
* @NL80211_RRF_NO_OUTDOOR: outdoor operation not allowed
* @NL80211_RRF_DFS: DFS support is required to be used
* @NL80211_RRF_PTP_ONLY: this is only for Point To Point links
* @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links
* @NL80211_RRF_PASSIVE_SCAN: passive scan is required
* @NL80211_RRF_NO_IBSS: no IBSS is allowed
*/
enum nl80211_reg_rule_flags {
NL80211_RRF_NO_OFDM = 1<<0,
NL80211_RRF_NO_CCK = 1<<1,
NL80211_RRF_NO_INDOOR = 1<<2,
NL80211_RRF_NO_OUTDOOR = 1<<3,
NL80211_RRF_DFS = 1<<4,
NL80211_RRF_PTP_ONLY = 1<<5,
NL80211_RRF_PTMP_ONLY = 1<<6,
NL80211_RRF_PASSIVE_SCAN = 1<<7,
NL80211_RRF_NO_IBSS = 1<<8,
};
/**
* enum nl80211_survey_info - survey information
*
* These attribute types are used with %NL80211_ATTR_SURVEY_INFO
* when getting information about a survey.
*
* @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
* @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
* @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
* @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
* @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio
* spent on this channel
* @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary
* channel was sensed busy (either due to activity or energy detect)
* @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension
* channel was sensed busy
* @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent
* receiving data
* @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent
* transmitting data
* @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
* currently defined
* @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
*/
enum nl80211_survey_info {
__NL80211_SURVEY_INFO_INVALID,
NL80211_SURVEY_INFO_FREQUENCY,
NL80211_SURVEY_INFO_NOISE,
NL80211_SURVEY_INFO_IN_USE,
NL80211_SURVEY_INFO_CHANNEL_TIME,
NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY,
NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY,
NL80211_SURVEY_INFO_CHANNEL_TIME_RX,
NL80211_SURVEY_INFO_CHANNEL_TIME_TX,
/* keep last */
__NL80211_SURVEY_INFO_AFTER_LAST,
NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
};
/**
* enum nl80211_mntr_flags - monitor configuration flags
*
* Monitor configuration flags.
*
* @__NL80211_MNTR_FLAG_INVALID: reserved
*
* @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS
* @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP
* @NL80211_MNTR_FLAG_CONTROL: pass control frames
* @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
* @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
* overrides all other flags.
*
* @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
* @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
*/
enum nl80211_mntr_flags {
__NL80211_MNTR_FLAG_INVALID,
NL80211_MNTR_FLAG_FCSFAIL,
NL80211_MNTR_FLAG_PLCPFAIL,
NL80211_MNTR_FLAG_CONTROL,
NL80211_MNTR_FLAG_OTHER_BSS,
NL80211_MNTR_FLAG_COOK_FRAMES,
/* keep last */
__NL80211_MNTR_FLAG_AFTER_LAST,
NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
};
/**
* enum nl80211_meshconf_params - mesh configuration parameters
*
* Mesh configuration parameters. These can be changed while the mesh is
* active.
*
* @__NL80211_MESHCONF_INVALID: internal use
*
* @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
* millisecond units, used by the Peer Link Open message
*
* @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
* millisecond units, used by the peer link management to close a peer link
*
* @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
* millisecond units
*
* @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed
* on this mesh interface
*
* @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link
* open retries that can be sent to establish a new peer link instance in a
* mesh
*
* @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
* point.
*
* @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically
* open peer links when we detect compatible mesh peers.
*
* @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames
* containing a PREQ that an MP can send to a particular destination (path
* target)
*
* @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths
* (in milliseconds)
*
* @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait
* until giving up on a path discovery (in milliseconds)
*
* @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh
* points receiving a PREQ shall consider the forwarding information from the
* root to be valid. (TU = time unit)
*
* @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in
* TUs) during which an MP can send only one action frame containing a PREQ
* reference element
*
* @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
* that it takes for an HWMP information element to propagate across the mesh
*
* @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
*
* @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
* source mesh point for path selection elements.
*
* @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
*
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
*/
enum nl80211_meshconf_params {
__NL80211_MESHCONF_INVALID,
NL80211_MESHCONF_RETRY_TIMEOUT,
NL80211_MESHCONF_CONFIRM_TIMEOUT,
NL80211_MESHCONF_HOLDING_TIMEOUT,
NL80211_MESHCONF_MAX_PEER_LINKS,
NL80211_MESHCONF_MAX_RETRIES,
NL80211_MESHCONF_TTL,
NL80211_MESHCONF_AUTO_OPEN_PLINKS,
NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES,
NL80211_MESHCONF_PATH_REFRESH_TIME,
NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT,
NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT,
NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
NL80211_MESHCONF_HWMP_ROOTMODE,
NL80211_MESHCONF_ELEMENT_TTL,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_mesh_setup_params - mesh setup parameters
*
* Mesh setup parameters. These are used to start/join a mesh and cannot be
* changed while the mesh is active.
*
* @__NL80211_MESH_SETUP_INVALID: Internal use
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
* vendor specific path selection algorithm or disable it to use the default
* HWMP.
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
* vendor specific path metric or disable it to use the default Airtime
* metric.
*
* @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
* robust security network ie, or a vendor specific information element that
* vendors will use to identify the path selection methods and metrics in use.
*
* @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
* daemon will be authenticating mesh candidates.
*
* @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
* @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
*/
enum nl80211_mesh_setup_params {
__NL80211_MESH_SETUP_INVALID,
NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
NL80211_MESH_SETUP_IE,
NL80211_MESH_SETUP_USERSPACE_AUTH,
/* keep last */
__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
};
/**
* enum nl80211_txq_attr - TX queue parameter attributes
* @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
* @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*)
* @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning
* disabled
* @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form
* 2^n-1 in the range 1..32767]
* @NL80211_TXQ_ATTR_CWMAX: Maximum contention window [a value of the form
* 2^n-1 in the range 1..32767]
* @NL80211_TXQ_ATTR_AIFS: Arbitration interframe space [0..255]
* @__NL80211_TXQ_ATTR_AFTER_LAST: Internal
* @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number
*/
enum nl80211_txq_attr {
__NL80211_TXQ_ATTR_INVALID,
NL80211_TXQ_ATTR_QUEUE,
NL80211_TXQ_ATTR_TXOP,
NL80211_TXQ_ATTR_CWMIN,
NL80211_TXQ_ATTR_CWMAX,
NL80211_TXQ_ATTR_AIFS,
/* keep last */
__NL80211_TXQ_ATTR_AFTER_LAST,
NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
};
enum nl80211_txq_q {
NL80211_TXQ_Q_VO,
NL80211_TXQ_Q_VI,
NL80211_TXQ_Q_BE,
NL80211_TXQ_Q_BK
};
enum nl80211_channel_type {
NL80211_CHAN_NO_HT,
NL80211_CHAN_HT20,
NL80211_CHAN_HT40MINUS,
NL80211_CHAN_HT40PLUS
};
/**
* enum nl80211_bss - netlink attributes for a BSS
*
* @__NL80211_BSS_INVALID: invalid
* @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
* @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
* @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
* @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
* @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
* @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
* raw information elements from the probe response/beacon (bin);
* if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
* from a Probe Response frame; otherwise they are from a Beacon frame.
* However, if the driver does not indicate the source of the IEs, these
* IEs may be from either frame subtype.
* @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
* in mBm (100 * dBm) (s32)
* @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
* in unspecified units, scaled to 0..100 (u8)
* @NL80211_BSS_STATUS: status, if this BSS is "used"
* @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms
* @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
enum nl80211_bss {
__NL80211_BSS_INVALID,
NL80211_BSS_BSSID,
NL80211_BSS_FREQUENCY,
NL80211_BSS_TSF,
NL80211_BSS_BEACON_INTERVAL,
NL80211_BSS_CAPABILITY,
NL80211_BSS_INFORMATION_ELEMENTS,
NL80211_BSS_SIGNAL_MBM,
NL80211_BSS_SIGNAL_UNSPEC,
NL80211_BSS_STATUS,
NL80211_BSS_SEEN_MS_AGO,
NL80211_BSS_BEACON_IES,
/* keep last */
__NL80211_BSS_AFTER_LAST,
NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1
};
/**
* enum nl80211_bss_status - BSS "status"
* @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
* @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
* @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
*
* The BSS status is a BSS attribute in scan dumps, which
* indicates the status the interface has wrt. this BSS.
*/
enum nl80211_bss_status {
NL80211_BSS_STATUS_AUTHENTICATED,
NL80211_BSS_STATUS_ASSOCIATED,
NL80211_BSS_STATUS_IBSS_JOINED,
};
/**
* enum nl80211_auth_type - AuthenticationType
*
* @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication
* @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
* @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
* @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
* @__NL80211_AUTHTYPE_NUM: internal
* @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
* @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
* trying multiple times); this is invalid in netlink -- leave out
* the attribute for this on CONNECT commands.
*/
enum nl80211_auth_type {
NL80211_AUTHTYPE_OPEN_SYSTEM,
NL80211_AUTHTYPE_SHARED_KEY,
NL80211_AUTHTYPE_FT,
NL80211_AUTHTYPE_NETWORK_EAP,
/* keep last */
__NL80211_AUTHTYPE_NUM,
NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1,
NL80211_AUTHTYPE_AUTOMATIC
};
/**
* enum nl80211_key_type - Key Type
* @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
* @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
* @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
* @NUM_NL80211_KEYTYPES: number of defined key types
*/
enum nl80211_key_type {
NL80211_KEYTYPE_GROUP,
NL80211_KEYTYPE_PAIRWISE,
NL80211_KEYTYPE_PEERKEY,
NUM_NL80211_KEYTYPES
};
/**
* enum nl80211_mfp - Management frame protection state
* @NL80211_MFP_NO: Management frame protection not used
* @NL80211_MFP_REQUIRED: Management frame protection required
*/
enum nl80211_mfp {
NL80211_MFP_NO,
NL80211_MFP_REQUIRED,
};
enum nl80211_wpa_versions {
NL80211_WPA_VERSION_1 = 1 << 0,
NL80211_WPA_VERSION_2 = 1 << 1,
};
/**
* enum nl80211_key_default_types - key default types
* @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
* @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
* unicast key
* @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
* multicast key
* @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
*/
enum nl80211_key_default_types {
__NL80211_KEY_DEFAULT_TYPE_INVALID,
NL80211_KEY_DEFAULT_TYPE_UNICAST,
NL80211_KEY_DEFAULT_TYPE_MULTICAST,
NUM_NL80211_KEY_DEFAULT_TYPES
};
/**
* enum nl80211_key_attributes - key attributes
* @__NL80211_KEY_INVALID: invalid
* @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
* 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
* keys
* @NL80211_KEY_IDX: key ID (u8, 0-3)
* @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
* @NL80211_KEY_DEFAULT: flag indicating default key
* @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
* @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
* specified the default depends on whether a MAC address was
* given with the command using the key or not (u32)
* @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* See &enum nl80211_key_default_types.
* @__NL80211_KEY_AFTER_LAST: internal
* @NL80211_KEY_MAX: highest key attribute
*/
enum nl80211_key_attributes {
__NL80211_KEY_INVALID,
NL80211_KEY_DATA,
NL80211_KEY_IDX,
NL80211_KEY_CIPHER,
NL80211_KEY_SEQ,
NL80211_KEY_DEFAULT,
NL80211_KEY_DEFAULT_MGMT,
NL80211_KEY_TYPE,
NL80211_KEY_DEFAULT_TYPES,
/* keep last */
__NL80211_KEY_AFTER_LAST,
NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1
};
/**
* enum nl80211_tx_rate_attributes - TX rate set attributes
* @__NL80211_TXRATE_INVALID: invalid
* @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection
* in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
* 1 = 500 kbps) but without the IE length restriction (at most
* %NL80211_MAX_SUPP_RATES in a single array).
* @__NL80211_TXRATE_AFTER_LAST: internal
* @NL80211_TXRATE_MAX: highest TX rate attribute
*/
enum nl80211_tx_rate_attributes {
__NL80211_TXRATE_INVALID,
NL80211_TXRATE_LEGACY,
/* keep last */
__NL80211_TXRATE_AFTER_LAST,
NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
};
/**
* enum nl80211_band - Frequency band
* @NL80211_BAND_2GHZ: 2.4 GHz ISM band
* @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
*/
enum nl80211_band {
NL80211_BAND_2GHZ,
NL80211_BAND_5GHZ,
};
enum nl80211_ps_state {
NL80211_PS_DISABLED,
NL80211_PS_ENABLED,
};
/**
* enum nl80211_attr_cqm - connection quality monitor attributes
* @__NL80211_ATTR_CQM_INVALID: invalid
* @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies
* the threshold for the RSSI level at which an event will be sent. Zero
* to disable.
* @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies
* the minimum amount the RSSI level must change after an event before a
* new event may be issued (to reduce effects of RSSI oscillation).
* @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
* @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
* consecutive packets were not acknowledged by the peer
* @__NL80211_ATTR_CQM_AFTER_LAST: internal
* @NL80211_ATTR_CQM_MAX: highest key attribute
*/
enum nl80211_attr_cqm {
__NL80211_ATTR_CQM_INVALID,
NL80211_ATTR_CQM_RSSI_THOLD,
NL80211_ATTR_CQM_RSSI_HYST,
NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
NL80211_ATTR_CQM_PKT_LOSS_EVENT,
/* keep last */
__NL80211_ATTR_CQM_AFTER_LAST,
NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1
};
/**
* enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
* @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
* configured threshold
* @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
* configured threshold
*/
enum nl80211_cqm_rssi_threshold_event {
NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
};
/**
* enum nl80211_tx_power_setting - TX power adjustment
* @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
* @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
* @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
*/
enum nl80211_tx_power_setting {
NL80211_TX_POWER_AUTOMATIC,
NL80211_TX_POWER_LIMITED,
NL80211_TX_POWER_FIXED,
};
#endif /* __LINUX_NL80211_H */