igb: add locking to reads of the i2c interface
The current implementation of sgmii support isn't correctly locking the
interfaces for reads/writes. This change pulls the read/write
functionality out of 82575.c and moves it to phy.c. In addition it
replaces the implementation in 82575.c with one that uses locking around
the relocated i2c interface calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/igb/e1000_82575.c b/drivers/net/igb/e1000_82575.c
index 65b9000..7897181 100644
--- a/drivers/net/igb/e1000_82575.c
+++ b/drivers/net/igb/e1000_82575.c
@@ -277,45 +277,23 @@
static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
u16 *data)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i, i2ccmd = 0;
+ s32 ret_val = -E1000_ERR_PARAM;
if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
hw_dbg("PHY Address %u is out of range\n", offset);
- return -E1000_ERR_PARAM;
+ goto out;
}
- /*
- * Set up Op-code, Phy Address, and register address in the I2CCMD
- * register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
- (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) |
- (E1000_I2CCMD_OPCODE_READ));
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
- wr32(E1000_I2CCMD, i2ccmd);
+ ret_val = igb_read_phy_reg_i2c(hw, offset, data);
- /* Poll the ready bit to see if the I2C read completed */
- for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
- udelay(50);
- i2ccmd = rd32(E1000_I2CCMD);
- if (i2ccmd & E1000_I2CCMD_READY)
- break;
- }
- if (!(i2ccmd & E1000_I2CCMD_READY)) {
- hw_dbg("I2CCMD Read did not complete\n");
- return -E1000_ERR_PHY;
- }
- if (i2ccmd & E1000_I2CCMD_ERROR) {
- hw_dbg("I2CCMD Error bit set\n");
- return -E1000_ERR_PHY;
- }
+ hw->phy.ops.release(hw);
- /* Need to byte-swap the 16-bit value. */
- *data = ((i2ccmd >> 8) & 0x00FF) | ((i2ccmd << 8) & 0xFF00);
-
- return 0;
+out:
+ return ret_val;
}
/**
@@ -330,47 +308,24 @@
static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
u16 data)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i, i2ccmd = 0;
- u16 phy_data_swapped;
+ s32 ret_val = -E1000_ERR_PARAM;
+
if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
hw_dbg("PHY Address %d is out of range\n", offset);
- return -E1000_ERR_PARAM;
+ goto out;
}
- /* Swap the data bytes for the I2C interface */
- phy_data_swapped = ((data >> 8) & 0x00FF) | ((data << 8) & 0xFF00);
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
- /*
- * Set up Op-code, Phy Address, and register address in the I2CCMD
- * register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
- (phy->addr << E1000_I2CCMD_PHY_ADDR_SHIFT) |
- E1000_I2CCMD_OPCODE_WRITE |
- phy_data_swapped);
+ ret_val = igb_write_phy_reg_i2c(hw, offset, data);
- wr32(E1000_I2CCMD, i2ccmd);
+ hw->phy.ops.release(hw);
- /* Poll the ready bit to see if the I2C read completed */
- for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
- udelay(50);
- i2ccmd = rd32(E1000_I2CCMD);
- if (i2ccmd & E1000_I2CCMD_READY)
- break;
- }
- if (!(i2ccmd & E1000_I2CCMD_READY)) {
- hw_dbg("I2CCMD Write did not complete\n");
- return -E1000_ERR_PHY;
- }
- if (i2ccmd & E1000_I2CCMD_ERROR) {
- hw_dbg("I2CCMD Error bit set\n");
- return -E1000_ERR_PHY;
- }
-
- return 0;
+out:
+ return ret_val;
}
/**