brcmfmac: add dedicated log level for low-level sdio debugging
The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
index a5354e7..d2a9d78 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
@@ -675,7 +675,7 @@
u8 clkctl, clkreq, devctl;
unsigned long timeout;
- brcmf_dbg(TRACE, "Enter\n");
+ brcmf_dbg(SDIO, "Enter\n");
clkctl = 0;
@@ -713,7 +713,7 @@
devctl |= SBSDIO_DEVCTL_CA_INT_ONLY;
brcmf_sdio_regwb(bus->sdiodev, SBSDIO_DEVICE_CTL,
devctl, &err);
- brcmf_dbg(INFO, "CLKCTL: set PENDING\n");
+ brcmf_dbg(SDIO, "CLKCTL: set PENDING\n");
bus->clkstate = CLK_PENDING;
return 0;
@@ -750,7 +750,7 @@
/* Mark clock available */
bus->clkstate = CLK_AVAIL;
- brcmf_dbg(INFO, "CLKCTL: turned ON\n");
+ brcmf_dbg(SDIO, "CLKCTL: turned ON\n");
#if defined(DEBUG)
if (!bus->alp_only) {
@@ -775,7 +775,7 @@
bus->clkstate = CLK_SDONLY;
brcmf_sdio_regwb(bus->sdiodev, SBSDIO_FUNC1_CHIPCLKCSR,
clkreq, &err);
- brcmf_dbg(INFO, "CLKCTL: turned OFF\n");
+ brcmf_dbg(SDIO, "CLKCTL: turned OFF\n");
if (err) {
brcmf_err("Failed access turning clock off: %d\n",
err);
@@ -788,7 +788,7 @@
/* Change idle/active SD state */
static int brcmf_sdbrcm_sdclk(struct brcmf_sdio *bus, bool on)
{
- brcmf_dbg(TRACE, "Enter\n");
+ brcmf_dbg(SDIO, "Enter\n");
if (on)
bus->clkstate = CLK_SDONLY;
@@ -805,7 +805,7 @@
uint oldstate = bus->clkstate;
#endif /* DEBUG */
- brcmf_dbg(TRACE, "Enter\n");
+ brcmf_dbg(SDIO, "Enter\n");
/* Early exit if we're already there */
if (bus->clkstate == target) {
@@ -849,7 +849,7 @@
break;
}
#ifdef DEBUG
- brcmf_dbg(INFO, "%d -> %d\n", oldstate, bus->clkstate);
+ brcmf_dbg(SDIO, "%d -> %d\n", oldstate, bus->clkstate);
#endif /* DEBUG */
return 0;
@@ -862,7 +862,7 @@
u8 fcbits;
int ret;
- brcmf_dbg(TRACE, "Enter\n");
+ brcmf_dbg(SDIO, "Enter\n");
/* Read mailbox data and ack that we did so */
ret = r_sdreg32(bus, &hmb_data,
@@ -875,7 +875,7 @@
/* Dongle recomposed rx frames, accept them again */
if (hmb_data & HMB_DATA_NAKHANDLED) {
- brcmf_dbg(INFO, "Dongle reports NAK handled, expect rtx of %d\n",
+ brcmf_dbg(SDIO, "Dongle reports NAK handled, expect rtx of %d\n",
bus->rx_seq);
if (!bus->rxskip)
brcmf_err("unexpected NAKHANDLED!\n");
@@ -896,7 +896,7 @@
"expecting %d\n",
bus->sdpcm_ver, SDPCM_PROT_VERSION);
else
- brcmf_dbg(INFO, "Dongle ready, protocol version %d\n",
+ brcmf_dbg(SDIO, "Dongle ready, protocol version %d\n",
bus->sdpcm_ver);
}
@@ -970,7 +970,7 @@
if (!retries)
brcmf_err("count never zeroed: last 0x%04x\n", lastrbc);
else
- brcmf_dbg(INFO, "flush took %d iterations\n", 0xffff - retries);
+ brcmf_dbg(SDIO, "flush took %d iterations\n", 0xffff - retries);
if (rtx) {
bus->sdcnt.rxrtx++;
@@ -1173,7 +1173,7 @@
/* If packets, issue read(s) and send up packet chain */
/* Return sequence numbers consumed? */
- brcmf_dbg(TRACE, "start: glomd %p glom %p\n",
+ brcmf_dbg(SDIO, "start: glomd %p glom %p\n",
bus->glomd, skb_peek(&bus->glom));
/* If there's a descriptor, generate the packet chain */
@@ -2117,7 +2117,7 @@
bus->sdiodev->bus_if->state = BRCMF_BUS_DOWN;
}
- brcmf_dbg(INFO, "DPC: PENDING, devctl 0x%02x clkctl 0x%02x\n",
+ brcmf_dbg(SDIO, "DPC: PENDING, devctl 0x%02x clkctl 0x%02x\n",
devctl, clkctl);
if (SBSDIO_HTAV(clkctl)) {
@@ -2387,7 +2387,7 @@
/* Do the transfer(s) */
while (size) {
- brcmf_dbg(INFO, "%s %d bytes at offset 0x%08x in window 0x%08x\n",
+ brcmf_dbg(SDIO, "%s %d bytes at offset 0x%08x in window 0x%08x\n",
write ? "write" : "read", dsize,
sdaddr, address & SBSDIO_SBWINDOW_MASK);
bcmerror = brcmf_sdcard_rwdata(bus->sdiodev, write,
@@ -2620,10 +2620,10 @@
msecs_to_jiffies(2000));
if (!bus->ctrl_frame_stat) {
- brcmf_dbg(INFO, "ctrl_frame_stat == false\n");
+ brcmf_dbg(SDIO, "ctrl_frame_stat == false\n");
ret = 0;
} else {
- brcmf_dbg(INFO, "ctrl_frame_stat == true\n");
+ brcmf_dbg(SDIO, "ctrl_frame_stat == true\n");
ret = -1;
}
}
@@ -2694,7 +2694,7 @@
addr = le32_to_cpu(addr_le);
- brcmf_dbg(INFO, "sdpcm_shared address 0x%08X\n", addr);
+ brcmf_dbg(SDIO, "sdpcm_shared address 0x%08X\n", addr);
/*
* Check if addr is valid.