Merge tty-next into 3.6-rc1
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
new file mode 100644
index 0000000..0d439df
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
@@ -0,0 +1,14 @@
+* NXP LPC32xx SoC High Speed UART
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-hsuart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+
+Example:
+
+ uart1: serial@40014000 {
+ compatible = "nxp,lpc3220-hsuart";
+ reg = <0x40014000 0x1000>;
+ interrupts = <26 0>;
+ };
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
index 0847fde..ba385f2 100644
--- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
@@ -25,6 +25,8 @@
accesses to the UART (e.g. TI davinci).
- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
RTAS and should not be registered.
+- no-loopback-test: set to indicate that the port does not implements loopback
+ test mode
Example:
diff --git a/arch/ia64/hp/sim/simserial.c b/arch/ia64/hp/sim/simserial.c
index c34785d..1ce97f4 100644
--- a/arch/ia64/hp/sim/simserial.c
+++ b/arch/ia64/hp/sim/simserial.c
@@ -338,7 +338,7 @@
{
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
}
}
diff --git a/drivers/bluetooth/hci_ath.c b/drivers/bluetooth/hci_ath.c
index 12172a6..0bc8a6a 100644
--- a/drivers/bluetooth/hci_ath.c
+++ b/drivers/bluetooth/hci_ath.c
@@ -58,7 +58,7 @@
return status;
/* Disable Automatic RTSCTS */
- memcpy(&ktermios, tty->termios, sizeof(ktermios));
+ ktermios = tty->termios;
ktermios.c_cflag &= ~CRTSCTS;
tty_set_termios(tty, &ktermios);
diff --git a/drivers/char/mwave/mwavedd.c b/drivers/char/mwave/mwavedd.c
index 1d82d58..164544a 100644
--- a/drivers/char/mwave/mwavedd.c
+++ b/drivers/char/mwave/mwavedd.c
@@ -430,7 +430,7 @@
static int register_serial_portandirq(unsigned int port, int irq)
{
- struct uart_port uart;
+ struct uart_8250_port uart;
switch ( port ) {
case 0x3f8:
@@ -462,14 +462,14 @@
} /* switch */
/* irq is okay */
- memset(&uart, 0, sizeof(struct uart_port));
+ memset(&uart, 0, sizeof(uart));
- uart.uartclk = 1843200;
- uart.iobase = port;
- uart.irq = irq;
- uart.iotype = UPIO_PORT;
- uart.flags = UPF_SHARE_IRQ;
- return serial8250_register_port(&uart);
+ uart.port.uartclk = 1843200;
+ uart.port.iobase = port;
+ uart.port.irq = irq;
+ uart.port.iotype = UPIO_PORT;
+ uart.port.flags = UPF_SHARE_IRQ;
+ return serial8250_register_8250_port(&uart);
}
diff --git a/drivers/char/pcmcia/synclink_cs.c b/drivers/char/pcmcia/synclink_cs.c
index 0a484b4..d0cbd29 100644
--- a/drivers/char/pcmcia/synclink_cs.c
+++ b/drivers/char/pcmcia/synclink_cs.c
@@ -1344,7 +1344,7 @@
/* TODO:disable interrupts instead of reset to preserve signal states */
reset_device(info);
- if (!tty || tty->termios->c_cflag & HUPCL) {
+ if (!tty || tty->termios.c_cflag & HUPCL) {
info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
set_signals(info);
}
@@ -1385,7 +1385,7 @@
port_irq_enable(info, (unsigned char) PVR_DSR | PVR_RI);
get_signals(info);
- if (info->netcount || (tty && (tty->termios->c_cflag & CREAD)))
+ if (info->netcount || (tty && (tty->termios.c_cflag & CREAD)))
rx_start(info);
spin_unlock_irqrestore(&info->lock,flags);
@@ -1398,14 +1398,14 @@
unsigned cflag;
int bits_per_char;
- if (!tty || !tty->termios)
+ if (!tty)
return;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):mgslpc_change_params(%s)\n",
__FILE__,__LINE__, info->device_name );
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
@@ -1728,7 +1728,7 @@
if (I_IXOFF(tty))
mgslpc_send_xchar(tty, STOP_CHAR(tty));
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->serial_signals &= ~SerialSignal_RTS;
set_signals(info);
@@ -1757,7 +1757,7 @@
mgslpc_send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->serial_signals |= SerialSignal_RTS;
set_signals(info);
@@ -2293,8 +2293,8 @@
tty->driver->name );
/* just return if nothing has changed */
- if ((tty->termios->c_cflag == old_termios->c_cflag)
- && (RELEVANT_IFLAG(tty->termios->c_iflag)
+ if ((tty->termios.c_cflag == old_termios->c_cflag)
+ && (RELEVANT_IFLAG(tty->termios.c_iflag)
== RELEVANT_IFLAG(old_termios->c_iflag)))
return;
@@ -2302,7 +2302,7 @@
/* Handle transition to B0 status */
if (old_termios->c_cflag & CBAUD &&
- !(tty->termios->c_cflag & CBAUD)) {
+ !(tty->termios.c_cflag & CBAUD)) {
info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
spin_lock_irqsave(&info->lock,flags);
set_signals(info);
@@ -2311,9 +2311,9 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
- tty->termios->c_cflag & CBAUD) {
+ tty->termios.c_cflag & CBAUD) {
info->serial_signals |= SerialSignal_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
info->serial_signals |= SerialSignal_RTS;
}
@@ -2324,7 +2324,7 @@
/* Handle turning off CRTSCTS */
if (old_termios->c_cflag & CRTSCTS &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
tx_release(tty);
}
diff --git a/drivers/isdn/gigaset/interface.c b/drivers/isdn/gigaset/interface.c
index a6d9fd2..f9aab74 100644
--- a/drivers/isdn/gigaset/interface.c
+++ b/drivers/isdn/gigaset/interface.c
@@ -446,8 +446,8 @@
goto out;
}
- iflag = tty->termios->c_iflag;
- cflag = tty->termios->c_cflag;
+ iflag = tty->termios.c_iflag;
+ cflag = tty->termios.c_cflag;
old_cflag = old ? old->c_cflag : cflag;
gig_dbg(DEBUG_IF, "%u: iflag %x cflag %x old %x",
cs->minor_index, iflag, cflag, old_cflag);
diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c
index 7bc5067..7a61ef6 100644
--- a/drivers/isdn/i4l/isdn_tty.c
+++ b/drivers/isdn/i4l/isdn_tty.c
@@ -1009,15 +1009,15 @@
quot;
int i;
- if (!port->tty || !port->tty->termios)
+ if (!port->tty)
return;
- cflag = port->tty->termios->c_cflag;
+ cflag = port->tty->termios.c_cflag;
quot = i = cflag & CBAUD;
if (i & CBAUDEX) {
i &= ~CBAUDEX;
if (i < 1 || i > 2)
- port->tty->termios->c_cflag &= ~CBAUDEX;
+ port->tty->termios.c_cflag &= ~CBAUDEX;
else
i += 15;
}
@@ -1097,7 +1097,7 @@
#endif
isdn_unlock_drivers();
info->msr &= ~UART_MSR_RI;
- if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
+ if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
info->mcr &= ~(UART_MCR_DTR | UART_MCR_RTS);
if (info->emu.mdmreg[REG_DTRHUP] & BIT_DTRHUP) {
isdn_tty_modem_reset_regs(info, 0);
@@ -1469,13 +1469,13 @@
if (!old_termios)
isdn_tty_change_speed(info);
else {
- if (tty->termios->c_cflag == old_termios->c_cflag &&
- tty->termios->c_ispeed == old_termios->c_ispeed &&
- tty->termios->c_ospeed == old_termios->c_ospeed)
+ if (tty->termios.c_cflag == old_termios->c_cflag &&
+ tty->termios.c_ispeed == old_termios->c_ispeed &&
+ tty->termios.c_ospeed == old_termios->c_ospeed)
return;
isdn_tty_change_speed(info);
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS))
+ !(tty->termios.c_cflag & CRTSCTS))
tty->hw_stopped = 0;
}
}
diff --git a/drivers/misc/ibmasm/uart.c b/drivers/misc/ibmasm/uart.c
index 1dcb9ae..01e2b0d 100644
--- a/drivers/misc/ibmasm/uart.c
+++ b/drivers/misc/ibmasm/uart.c
@@ -33,7 +33,7 @@
void ibmasm_register_uart(struct service_processor *sp)
{
- struct uart_port uport;
+ struct uart_8250_port uart;
void __iomem *iomem_base;
iomem_base = sp->base_address + SCOUT_COM_B_BASE;
@@ -47,14 +47,14 @@
return;
}
- memset(&uport, 0, sizeof(struct uart_port));
- uport.irq = sp->irq;
- uport.uartclk = 3686400;
- uport.flags = UPF_SHARE_IRQ;
- uport.iotype = UPIO_MEM;
- uport.membase = iomem_base;
+ memset(&uart, 0, sizeof(uart));
+ uart.port.irq = sp->irq;
+ uart.port.uartclk = 3686400;
+ uart.port.flags = UPF_SHARE_IRQ;
+ uart.port.iotype = UPIO_MEM;
+ uart.port.membase = iomem_base;
- sp->serial_line = serial8250_register_port(&uport);
+ sp->serial_line = serial8250_register_8250_port(&uart);
if (sp->serial_line < 0) {
dev_err(sp->dev, "Failed to register serial port\n");
return;
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index 5a2cbfa..372c0325 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -518,7 +518,7 @@
if (status & UART_MSR_DCTS) {
port->icount.cts++;
tty = tty_port_tty_get(&port->port);
- if (tty && (tty->termios->c_cflag & CRTSCTS)) {
+ if (tty && (tty->termios.c_cflag & CRTSCTS)) {
int cts = (status & UART_MSR_CTS);
if (tty->hw_stopped) {
if (cts) {
@@ -671,12 +671,12 @@
port->ier = UART_IER_RLSI|UART_IER_RDI|UART_IER_RTOIE|UART_IER_UUE;
port->mctrl = TIOCM_OUT2;
- sdio_uart_change_speed(port, tty->termios, NULL);
+ sdio_uart_change_speed(port, &tty->termios, NULL);
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
sdio_uart_set_mctrl(port, TIOCM_RTS | TIOCM_DTR);
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
if (!(sdio_uart_get_mctrl(port) & TIOCM_CTS))
tty->hw_stopped = 1;
@@ -850,7 +850,7 @@
{
struct sdio_uart_port *port = tty->driver_data;
- if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS))
+ if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS))
return;
if (sdio_uart_claim_func(port) != 0)
@@ -861,7 +861,7 @@
sdio_uart_start_tx(port);
}
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
sdio_uart_clear_mctrl(port, TIOCM_RTS);
sdio_uart_irq(port->func);
@@ -872,7 +872,7 @@
{
struct sdio_uart_port *port = tty->driver_data;
- if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS))
+ if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS))
return;
if (sdio_uart_claim_func(port) != 0)
@@ -887,7 +887,7 @@
}
}
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
sdio_uart_set_mctrl(port, TIOCM_RTS);
sdio_uart_irq(port->func);
@@ -898,12 +898,12 @@
struct ktermios *old_termios)
{
struct sdio_uart_port *port = tty->driver_data;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
if (sdio_uart_claim_func(port) != 0)
return;
- sdio_uart_change_speed(port, tty->termios, old_termios);
+ sdio_uart_change_speed(port, &tty->termios, old_termios);
/* Handle transition to B0 status */
if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD))
diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c
index b5ba308..3e5519a 100644
--- a/drivers/net/ethernet/sgi/ioc3-eth.c
+++ b/drivers/net/ethernet/sgi/ioc3-eth.c
@@ -1147,15 +1147,17 @@
{
#define COSMISC_CONSTANT 6
- struct uart_port port = {
- .irq = 0,
- .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
- .iotype = UPIO_MEM,
- .regshift = 0,
- .uartclk = (22000000 << 1) / COSMISC_CONSTANT,
+ struct uart_8250_port port = {
+ .port = {
+ .irq = 0,
+ .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM,
+ .regshift = 0,
+ .uartclk = (22000000 << 1) / COSMISC_CONSTANT,
- .membase = (unsigned char __iomem *) uart,
- .mapbase = (unsigned long) uart,
+ .membase = (unsigned char __iomem *) uart,
+ .mapbase = (unsigned long) uart,
+ }
};
unsigned char lcr;
@@ -1164,7 +1166,7 @@
uart->iu_scr = COSMISC_CONSTANT,
uart->iu_lcr = lcr;
uart->iu_lcr;
- serial8250_register_port(&port);
+ serial8250_register_8250_port(&port);
}
static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3)
diff --git a/drivers/net/irda/irtty-sir.c b/drivers/net/irda/irtty-sir.c
index 3352b24..30087ca 100644
--- a/drivers/net/irda/irtty-sir.c
+++ b/drivers/net/irda/irtty-sir.c
@@ -124,8 +124,8 @@
tty = priv->tty;
mutex_lock(&tty->termios_mutex);
- old_termios = *(tty->termios);
- cflag = tty->termios->c_cflag;
+ old_termios = tty->termios;
+ cflag = tty->termios.c_cflag;
tty_encode_baud_rate(tty, speed, speed);
if (tty->ops->set_termios)
tty->ops->set_termios(tty, &old_termios);
@@ -281,15 +281,15 @@
int cflag;
mutex_lock(&tty->termios_mutex);
- old_termios = *(tty->termios);
- cflag = tty->termios->c_cflag;
+ old_termios = tty->termios;
+ cflag = tty->termios.c_cflag;
if (stop)
cflag &= ~CREAD;
else
cflag |= CREAD;
- tty->termios->c_cflag = cflag;
+ tty->termios.c_cflag = cflag;
if (tty->ops->set_termios)
tty->ops->set_termios(tty, &old_termios);
mutex_unlock(&tty->termios_mutex);
diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c
index 62f30b4..7736af7 100644
--- a/drivers/net/usb/hso.c
+++ b/drivers/net/usb/hso.c
@@ -1107,7 +1107,6 @@
struct ktermios *old)
{
struct hso_serial *serial = tty->driver_data;
- struct ktermios *termios;
if (!serial) {
printk(KERN_ERR "%s: no tty structures", __func__);
@@ -1119,16 +1118,15 @@
/*
* Fix up unsupported bits
*/
- termios = tty->termios;
- termios->c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */
+ tty->termios.c_iflag &= ~IXON; /* disable enable XON/XOFF flow control */
- termios->c_cflag &=
+ tty->termios.c_cflag &=
~(CSIZE /* no size */
| PARENB /* disable parity bit */
| CBAUD /* clear current baud rate */
| CBAUDEX); /* clear current buad rate */
- termios->c_cflag |= CS8; /* character size 8 bits */
+ tty->termios.c_cflag |= CS8; /* character size 8 bits */
/* baud rate 115200 */
tty_encode_baud_rate(tty, 115200, 115200);
@@ -1425,14 +1423,14 @@
if (old)
D5("Termios called with: cflags new[%d] - old[%d]",
- tty->termios->c_cflag, old->c_cflag);
+ tty->termios.c_cflag, old->c_cflag);
/* the actual setup */
spin_lock_irqsave(&serial->serial_lock, flags);
if (serial->port.count)
_hso_serial_set_termios(tty, old);
else
- tty->termios = old;
+ tty->termios = *old;
spin_unlock_irqrestore(&serial->serial_lock, flags);
/* done */
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
index 6cc4358..0e8441e 100644
--- a/drivers/tty/amiserial.c
+++ b/drivers/tty/amiserial.c
@@ -646,7 +646,7 @@
custom.adkcon = AC_UARTBRK;
mb();
- if (tty->termios->c_cflag & HUPCL)
+ if (tty->termios.c_cflag & HUPCL)
info->MCR &= ~(SER_DTR|SER_RTS);
rtsdtr_ctrl(info->MCR);
@@ -670,7 +670,7 @@
int bits;
unsigned long flags;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
/* Byte size is always 8 bits plus parity bit if requested */
@@ -707,8 +707,8 @@
/* If the quotient is zero refuse the change */
if (!quot && old_termios) {
/* FIXME: Will need updating for new tty in the end */
- tty->termios->c_cflag &= ~CBAUD;
- tty->termios->c_cflag |= (old_termios->c_cflag & CBAUD);
+ tty->termios.c_cflag &= ~CBAUD;
+ tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD);
baud = tty_get_baud_rate(tty);
if (!baud)
baud = 9600;
@@ -984,7 +984,7 @@
if (I_IXOFF(tty))
rs_send_xchar(tty, STOP_CHAR(tty));
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
info->MCR &= ~SER_RTS;
local_irq_save(flags);
@@ -1012,7 +1012,7 @@
else
rs_send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
info->MCR |= SER_RTS;
local_irq_save(flags);
rtsdtr_ctrl(info->MCR);
@@ -1330,7 +1330,7 @@
{
struct serial_state *info = tty->driver_data;
unsigned long flags;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
change_speed(tty, info, old_termios);
@@ -1347,7 +1347,7 @@
if (!(old_termios->c_cflag & CBAUD) &&
(cflag & CBAUD)) {
info->MCR |= SER_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
info->MCR |= SER_RTS;
}
@@ -1358,7 +1358,7 @@
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
rs_start(tty);
}
@@ -1371,7 +1371,7 @@
* or not. Hence, this may change.....
*/
if (!(old_termios->c_cflag & CLOCAL) &&
- (tty->termios->c_cflag & CLOCAL))
+ (tty->termios.c_cflag & CLOCAL))
wake_up_interruptible(&info->open_wait);
#endif
}
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index e61cabd..e77db71 100644
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -1459,7 +1459,7 @@
info->port.xmit_buf = NULL;
free_page((unsigned long)temp);
}
- if (tty->termios->c_cflag & HUPCL)
+ if (tty->termios.c_cflag & HUPCL)
cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR);
cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR);
@@ -1488,7 +1488,7 @@
free_page((unsigned long)temp);
}
- if (tty->termios->c_cflag & HUPCL)
+ if (tty->termios.c_cflag & HUPCL)
tty_port_lower_dtr_rts(&info->port);
set_bit(TTY_IO_ERROR, &tty->flags);
@@ -1999,14 +1999,11 @@
int baud, baud_rate = 0;
int i;
- if (!tty->termios) /* XXX can this happen at all? */
- return;
-
if (info->line == -1)
return;
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
/*
* Set up the tty->alt_speed kludge
@@ -2825,7 +2822,7 @@
cy_set_line_char(info, tty);
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
cy_start(tty);
}
@@ -2837,7 +2834,7 @@
* or not. Hence, this may change.....
*/
if (!(old_termios->c_cflag & CLOCAL) &&
- (tty->termios->c_cflag & CLOCAL))
+ (tty->termios.c_cflag & CLOCAL))
wake_up_interruptible(&info->port.open_wait);
#endif
} /* cy_set_termios */
@@ -2899,7 +2896,7 @@
info->throttle = 1;
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
if (!cy_is_Z(card)) {
spin_lock_irqsave(&card->card_lock, flags);
cyy_change_rts_dtr(info, 0, TIOCM_RTS);
@@ -2938,7 +2935,7 @@
cy_send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
card = info->card;
if (!cy_is_Z(card)) {
spin_lock_irqsave(&card->card_lock, flags);
@@ -3289,6 +3286,7 @@
static int __init cy_detect_isa(void)
{
#ifdef CONFIG_ISA
+ struct cyclades_card *card;
unsigned short cy_isa_irq, nboard;
void __iomem *cy_isa_address;
unsigned short i, j, cy_isa_nchan;
@@ -3349,7 +3347,8 @@
}
/* fill the next cy_card structure available */
for (j = 0; j < NR_CARDS; j++) {
- if (cy_card[j].base_addr == NULL)
+ card = &cy_card[j];
+ if (card->base_addr == NULL)
break;
}
if (j == NR_CARDS) { /* no more cy_cards available */
@@ -3363,7 +3362,7 @@
/* allocate IRQ */
if (request_irq(cy_isa_irq, cyy_interrupt,
- 0, "Cyclom-Y", &cy_card[j])) {
+ 0, "Cyclom-Y", card)) {
printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but "
"could not allocate IRQ#%d.\n",
(unsigned long)cy_isa_address, cy_isa_irq);
@@ -3372,16 +3371,16 @@
}
/* set cy_card */
- cy_card[j].base_addr = cy_isa_address;
- cy_card[j].ctl_addr.p9050 = NULL;
- cy_card[j].irq = (int)cy_isa_irq;
- cy_card[j].bus_index = 0;
- cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
- cy_card[j].nports = cy_isa_nchan;
- if (cy_init_card(&cy_card[j])) {
- cy_card[j].base_addr = NULL;
- free_irq(cy_isa_irq, &cy_card[j]);
+ card->base_addr = cy_isa_address;
+ card->ctl_addr.p9050 = NULL;
+ card->irq = (int)cy_isa_irq;
+ card->bus_index = 0;
+ card->first_line = cy_next_channel;
+ card->num_chips = cy_isa_nchan / CyPORTS_PER_CHIP;
+ card->nports = cy_isa_nchan;
+ if (cy_init_card(card)) {
+ card->base_addr = NULL;
+ free_irq(cy_isa_irq, card);
iounmap(cy_isa_address);
continue;
}
@@ -3695,6 +3694,7 @@
static int __devinit cy_pci_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
+ struct cyclades_card *card;
void __iomem *addr0 = NULL, *addr2 = NULL;
char *card_name = NULL;
u32 uninitialized_var(mailbox);
@@ -3829,7 +3829,8 @@
}
/* fill the next cy_card structure available */
for (card_no = 0; card_no < NR_CARDS; card_no++) {
- if (cy_card[card_no].base_addr == NULL)
+ card = &cy_card[card_no];
+ if (card->base_addr == NULL)
break;
}
if (card_no == NR_CARDS) { /* no more cy_cards available */
@@ -3843,27 +3844,26 @@
device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
/* allocate IRQ */
retval = request_irq(irq, cyy_interrupt,
- IRQF_SHARED, "Cyclom-Y", &cy_card[card_no]);
+ IRQF_SHARED, "Cyclom-Y", card);
if (retval) {
dev_err(&pdev->dev, "could not allocate IRQ\n");
goto err_unmap;
}
- cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP;
+ card->num_chips = nchan / CyPORTS_PER_CHIP;
} else {
struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS;
struct ZFW_CTRL __iomem *zfw_ctrl;
zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff);
- cy_card[card_no].hw_ver = mailbox;
- cy_card[card_no].num_chips = (unsigned int)-1;
- cy_card[card_no].board_ctrl = &zfw_ctrl->board_ctrl;
+ card->hw_ver = mailbox;
+ card->num_chips = (unsigned int)-1;
+ card->board_ctrl = &zfw_ctrl->board_ctrl;
#ifdef CONFIG_CYZ_INTR
/* allocate IRQ only if board has an IRQ */
if (irq != 0 && irq != 255) {
retval = request_irq(irq, cyz_interrupt,
- IRQF_SHARED, "Cyclades-Z",
- &cy_card[card_no]);
+ IRQF_SHARED, "Cyclades-Z", card);
if (retval) {
dev_err(&pdev->dev, "could not allocate IRQ\n");
goto err_unmap;
@@ -3873,17 +3873,17 @@
}
/* set cy_card */
- cy_card[card_no].base_addr = addr2;
- cy_card[card_no].ctl_addr.p9050 = addr0;
- cy_card[card_no].irq = irq;
- cy_card[card_no].bus_index = 1;
- cy_card[card_no].first_line = cy_next_channel;
- cy_card[card_no].nports = nchan;
- retval = cy_init_card(&cy_card[card_no]);
+ card->base_addr = addr2;
+ card->ctl_addr.p9050 = addr0;
+ card->irq = irq;
+ card->bus_index = 1;
+ card->first_line = cy_next_channel;
+ card->nports = nchan;
+ retval = cy_init_card(card);
if (retval)
goto err_null;
- pci_set_drvdata(pdev, &cy_card[card_no]);
+ pci_set_drvdata(pdev, card);
if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
@@ -3915,8 +3915,8 @@
return 0;
err_null:
- cy_card[card_no].base_addr = NULL;
- free_irq(irq, &cy_card[card_no]);
+ card->base_addr = NULL;
+ free_irq(irq, card);
err_unmap:
iounmap(addr0);
if (addr2)
diff --git a/drivers/tty/hvc/hvsi_lib.c b/drivers/tty/hvc/hvsi_lib.c
index 59c135d..3396eb9 100644
--- a/drivers/tty/hvc/hvsi_lib.c
+++ b/drivers/tty/hvc/hvsi_lib.c
@@ -400,7 +400,7 @@
spin_unlock_irqrestore(&hp->lock, flags);
/* Clear our own DTR */
- if (!pv->tty || (pv->tty->termios->c_cflag & HUPCL))
+ if (!pv->tty || (pv->tty->termios.c_cflag & HUPCL))
hvsilib_write_mctrl(pv, 0);
/* Tear down the connection */
diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c
index e1235ac..d593a7d 100644
--- a/drivers/tty/isicom.c
+++ b/drivers/tty/isicom.c
@@ -702,7 +702,7 @@
/* 1,2,3,4 => 57.6, 115.2, 230, 460 kbps resp. */
if (baud < 1 || baud > 4)
- tty->termios->c_cflag &= ~CBAUDEX;
+ tty->termios.c_cflag &= ~CBAUDEX;
else
baud += 15;
}
@@ -1196,8 +1196,8 @@
if (isicom_paranoia_check(port, tty->name, "isicom_set_termios"))
return;
- if (tty->termios->c_cflag == old_termios->c_cflag &&
- tty->termios->c_iflag == old_termios->c_iflag)
+ if (tty->termios.c_cflag == old_termios->c_cflag &&
+ tty->termios.c_iflag == old_termios->c_iflag)
return;
spin_lock_irqsave(&port->card->card_lock, flags);
@@ -1205,7 +1205,7 @@
spin_unlock_irqrestore(&port->card->card_lock, flags);
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
isicom_start(tty);
}
diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c
index 324467d..89cc934 100644
--- a/drivers/tty/moxa.c
+++ b/drivers/tty/moxa.c
@@ -367,10 +367,10 @@
tmp.dcd = 1;
ttyp = tty_port_tty_get(&p->port);
- if (!ttyp || !ttyp->termios)
+ if (!ttyp)
tmp.cflag = p->cflag;
else
- tmp.cflag = ttyp->termios->c_cflag;
+ tmp.cflag = ttyp->termios.c_cflag;
tty_kref_put(ttyp);
copy:
if (copy_to_user(argm, &tmp, sizeof(tmp)))
@@ -1178,7 +1178,7 @@
mutex_lock(&ch->port.mutex);
if (!(ch->port.flags & ASYNC_INITIALIZED)) {
ch->statusflags = 0;
- moxa_set_tty_param(tty, tty->termios);
+ moxa_set_tty_param(tty, &tty->termios);
MoxaPortLineCtrl(ch, 1, 1);
MoxaPortEnable(ch);
MoxaSetFifo(ch, ch->type == PORT_16550A);
@@ -1193,7 +1193,7 @@
static void moxa_close(struct tty_struct *tty, struct file *filp)
{
struct moxa_port *ch = tty->driver_data;
- ch->cflag = tty->termios->c_cflag;
+ ch->cflag = tty->termios.c_cflag;
tty_port_close(&ch->port, tty, filp);
}
@@ -1464,7 +1464,7 @@
static void moxa_set_tty_param(struct tty_struct *tty, struct ktermios *old_termios)
{
- register struct ktermios *ts = tty->termios;
+ register struct ktermios *ts = &tty->termios;
struct moxa_port *ch = tty->driver_data;
int rts, cts, txflow, rxflow, xany, baud;
diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 90cc680..c162ee9 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -643,7 +643,7 @@
int ret = 0;
unsigned char status;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
if (!info->ioaddr)
return ret;
@@ -1520,10 +1520,10 @@
tty = tty_port_tty_get(port);
- if (!tty || !tty->termios)
+ if (!tty)
ms.cflag = ip->normal_termios.c_cflag;
else
- ms.cflag = tty->termios->c_cflag;
+ ms.cflag = tty->termios.c_cflag;
tty_kref_put(tty);
spin_lock_irq(&ip->slock);
status = inb(ip->ioaddr + UART_MSR);
@@ -1589,13 +1589,13 @@
tty = tty_port_tty_get(&ip->port);
- if (!tty || !tty->termios) {
+ if (!tty) {
cflag = ip->normal_termios.c_cflag;
iflag = ip->normal_termios.c_iflag;
me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
} else {
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
me->baudrate[p] = tty_get_baud_rate(tty);
}
tty_kref_put(tty);
@@ -1853,7 +1853,7 @@
}
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
info->MCR &= ~UART_MCR_RTS;
outb(info->MCR, info->ioaddr + UART_MCR);
}
@@ -1890,7 +1890,7 @@
}
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
info->MCR |= UART_MCR_RTS;
outb(info->MCR, info->ioaddr + UART_MCR);
}
@@ -1939,14 +1939,14 @@
spin_unlock_irqrestore(&info->slock, flags);
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
mxser_start(tty);
}
/* Handle sw stopped */
if ((old_termios->c_iflag & IXON) &&
- !(tty->termios->c_iflag & IXON)) {
+ !(tty->termios.c_iflag & IXON)) {
tty->stopped = 0;
if (info->board->chip_flag) {
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index c43b683..7a4bf30 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -1061,7 +1061,7 @@
/* Carrier drop -> hangup */
if (tty) {
if ((mlines & TIOCM_CD) == 0 && (dlci->modem_rx & TIOCM_CD))
- if (!(tty->termios->c_cflag & CLOCAL))
+ if (!(tty->termios.c_cflag & CLOCAL))
tty_hangup(tty);
if (brk & 0x01)
tty_insert_flip_char(tty, 0, TTY_BREAK);
@@ -3043,13 +3043,13 @@
the RPN control message. This however rapidly gets nasty as we
then have to remap modem signals each way according to whether
our virtual cable is null modem etc .. */
- tty_termios_copy_hw(tty->termios, old);
+ tty_termios_copy_hw(&tty->termios, old);
}
static void gsmtty_throttle(struct tty_struct *tty)
{
struct gsm_dlci *dlci = tty->driver_data;
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
dlci->modem_tx &= ~TIOCM_DTR;
dlci->throttled = 1;
/* Send an MSC with DTR cleared */
@@ -3059,7 +3059,7 @@
static void gsmtty_unthrottle(struct tty_struct *tty)
{
struct gsm_dlci *dlci = tty->driver_data;
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
dlci->modem_tx |= TIOCM_DTR;
dlci->throttled = 0;
/* Send an MSC with DTR set */
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index ee1c268..101790c 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -1432,6 +1432,12 @@
*/
if (tty->receive_room < TTY_THRESHOLD_THROTTLE)
tty_throttle(tty);
+
+ /* FIXME: there is a tiny race here if the receive room check runs
+ before the other work executes and empties the buffer (upping
+ the receiving room and unthrottling. We then throttle and get
+ stuck. This has been observed and traced down by Vincent Pillet/
+ We need to address this when we sort out out the rx path locking */
}
int is_ignored(int sig)
@@ -1460,7 +1466,7 @@
BUG_ON(!tty);
if (old)
- canon_change = (old->c_lflag ^ tty->termios->c_lflag) & ICANON;
+ canon_change = (old->c_lflag ^ tty->termios.c_lflag) & ICANON;
if (canon_change) {
memset(&tty->read_flags, 0, sizeof tty->read_flags);
tty->canon_head = tty->read_tail;
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index 5505ffc..d6579a9 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -231,8 +231,8 @@
static void pty_set_termios(struct tty_struct *tty,
struct ktermios *old_termios)
{
- tty->termios->c_cflag &= ~(CSIZE | PARENB);
- tty->termios->c_cflag |= (CS8 | CREAD);
+ tty->termios.c_cflag &= ~(CSIZE | PARENB);
+ tty->termios.c_cflag |= (CS8 | CREAD);
}
/**
@@ -282,60 +282,107 @@
return 0;
}
-/* Traditional BSD devices */
-#ifdef CONFIG_LEGACY_PTYS
-
-static int pty_install(struct tty_driver *driver, struct tty_struct *tty)
+/**
+ * pty_common_install - set up the pty pair
+ * @driver: the pty driver
+ * @tty: the tty being instantiated
+ * @bool: legacy, true if this is BSD style
+ *
+ * Perform the initial set up for the tty/pty pair. Called from the
+ * tty layer when the port is first opened.
+ *
+ * Locking: the caller must hold the tty_mutex
+ */
+static int pty_common_install(struct tty_driver *driver, struct tty_struct *tty,
+ bool legacy)
{
struct tty_struct *o_tty;
+ struct tty_port *ports[2];
int idx = tty->index;
- int retval;
+ int retval = -ENOMEM;
o_tty = alloc_tty_struct();
- if (!o_tty)
- return -ENOMEM;
+ ports[0] = kmalloc(sizeof **ports, GFP_KERNEL);
+ ports[1] = kmalloc(sizeof **ports, GFP_KERNEL);
+ if (!o_tty || !ports[0] || !ports[1])
+ goto err_free_tty;
if (!try_module_get(driver->other->owner)) {
/* This cannot in fact currently happen */
- retval = -ENOMEM;
goto err_free_tty;
}
initialize_tty_struct(o_tty, driver->other, idx);
- /* We always use new tty termios data so we can do this
- the easy way .. */
- retval = tty_init_termios(tty);
- if (retval)
- goto err_deinit_tty;
+ if (legacy) {
+ /* We always use new tty termios data so we can do this
+ the easy way .. */
+ retval = tty_init_termios(tty);
+ if (retval)
+ goto err_deinit_tty;
- retval = tty_init_termios(o_tty);
- if (retval)
- goto err_free_termios;
+ retval = tty_init_termios(o_tty);
+ if (retval)
+ goto err_free_termios;
+
+ driver->other->ttys[idx] = o_tty;
+ driver->ttys[idx] = tty;
+ } else {
+ memset(&tty->termios_locked, 0, sizeof(tty->termios_locked));
+ tty->termios = driver->init_termios;
+ memset(&o_tty->termios_locked, 0, sizeof(tty->termios_locked));
+ o_tty->termios = driver->other->init_termios;
+ }
/*
* Everything allocated ... set up the o_tty structure.
*/
- driver->other->ttys[idx] = o_tty;
tty_driver_kref_get(driver->other);
if (driver->subtype == PTY_TYPE_MASTER)
o_tty->count++;
/* Establish the links in both directions */
tty->link = o_tty;
o_tty->link = tty;
+ tty_port_init(ports[0]);
+ tty_port_init(ports[1]);
+ o_tty->port = ports[0];
+ tty->port = ports[1];
tty_driver_kref_get(driver);
tty->count++;
- driver->ttys[idx] = tty;
return 0;
err_free_termios:
- tty_free_termios(tty);
+ if (legacy)
+ tty_free_termios(tty);
err_deinit_tty:
deinitialize_tty_struct(o_tty);
module_put(o_tty->driver->owner);
err_free_tty:
+ kfree(ports[0]);
+ kfree(ports[1]);
free_tty_struct(o_tty);
return retval;
}
+static void pty_cleanup(struct tty_struct *tty)
+{
+ kfree(tty->port);
+}
+
+/* Traditional BSD devices */
+#ifdef CONFIG_LEGACY_PTYS
+
+static int pty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+ return pty_common_install(driver, tty, true);
+}
+
+static void pty_remove(struct tty_driver *driver, struct tty_struct *tty)
+{
+ struct tty_struct *pair = tty->link;
+ driver->ttys[tty->index] = NULL;
+ if (pair)
+ pair->driver->ttys[pair->index] = NULL;
+}
+
static int pty_bsd_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg)
{
@@ -366,7 +413,9 @@
.unthrottle = pty_unthrottle,
.set_termios = pty_set_termios,
.ioctl = pty_bsd_ioctl,
- .resize = pty_resize
+ .cleanup = pty_cleanup,
+ .resize = pty_resize,
+ .remove = pty_remove
};
static const struct tty_operations slave_pty_ops_bsd = {
@@ -379,7 +428,9 @@
.chars_in_buffer = pty_chars_in_buffer,
.unthrottle = pty_unthrottle,
.set_termios = pty_set_termios,
- .resize = pty_resize
+ .cleanup = pty_cleanup,
+ .resize = pty_resize,
+ .remove = pty_remove
};
static void __init legacy_pty_init(void)
@@ -497,78 +548,22 @@
return tty;
}
-static void pty_unix98_shutdown(struct tty_struct *tty)
-{
- tty_driver_remove_tty(tty->driver, tty);
- /* We have our own method as we don't use the tty index */
- kfree(tty->termios);
-}
-
/* We have no need to install and remove our tty objects as devpts does all
the work for us */
static int pty_unix98_install(struct tty_driver *driver, struct tty_struct *tty)
{
- struct tty_struct *o_tty;
- int idx = tty->index;
-
- o_tty = alloc_tty_struct();
- if (!o_tty)
- return -ENOMEM;
- if (!try_module_get(driver->other->owner)) {
- /* This cannot in fact currently happen */
- goto err_free_tty;
- }
- initialize_tty_struct(o_tty, driver->other, idx);
-
- tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
- if (tty->termios == NULL)
- goto err_free_mem;
- *tty->termios = driver->init_termios;
- tty->termios_locked = tty->termios + 1;
-
- o_tty->termios = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
- if (o_tty->termios == NULL)
- goto err_free_mem;
- *o_tty->termios = driver->other->init_termios;
- o_tty->termios_locked = o_tty->termios + 1;
-
- tty_driver_kref_get(driver->other);
- if (driver->subtype == PTY_TYPE_MASTER)
- o_tty->count++;
- /* Establish the links in both directions */
- tty->link = o_tty;
- o_tty->link = tty;
- /*
- * All structures have been allocated, so now we install them.
- * Failures after this point use release_tty to clean up, so
- * there's no need to null out the local pointers.
- */
- tty_driver_kref_get(driver);
- tty->count++;
- return 0;
-err_free_mem:
- deinitialize_tty_struct(o_tty);
- kfree(o_tty->termios);
- kfree(tty->termios);
- module_put(o_tty->driver->owner);
-err_free_tty:
- free_tty_struct(o_tty);
- return -ENOMEM;
+ return pty_common_install(driver, tty, false);
}
-static void ptm_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
-{
-}
-
-static void pts_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
+static void pty_unix98_remove(struct tty_driver *driver, struct tty_struct *tty)
{
}
static const struct tty_operations ptm_unix98_ops = {
.lookup = ptm_unix98_lookup,
.install = pty_unix98_install,
- .remove = ptm_unix98_remove,
+ .remove = pty_unix98_remove,
.open = pty_open,
.close = pty_close,
.write = pty_write,
@@ -578,14 +573,14 @@
.unthrottle = pty_unthrottle,
.set_termios = pty_set_termios,
.ioctl = pty_unix98_ioctl,
- .shutdown = pty_unix98_shutdown,
- .resize = pty_resize
+ .resize = pty_resize,
+ .cleanup = pty_cleanup
};
static const struct tty_operations pty_unix98_ops = {
.lookup = pts_unix98_lookup,
.install = pty_unix98_install,
- .remove = pts_unix98_remove,
+ .remove = pty_unix98_remove,
.open = pty_open,
.close = pty_close,
.write = pty_write,
@@ -594,7 +589,7 @@
.chars_in_buffer = pty_chars_in_buffer,
.unthrottle = pty_unthrottle,
.set_termios = pty_set_termios,
- .shutdown = pty_unix98_shutdown
+ .cleanup = pty_cleanup,
};
/**
diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c
index 777d5f9..016984a 100644
--- a/drivers/tty/rocket.c
+++ b/drivers/tty/rocket.c
@@ -720,7 +720,7 @@
unsigned rocketMode;
int bits, baud, divisor;
CHANNEL_t *cp;
- struct ktermios *t = tty->termios;
+ struct ktermios *t = &tty->termios;
cp = &info->channel;
cflag = t->c_cflag;
@@ -978,7 +978,7 @@
tty->alt_speed = 460800;
configure_r_port(tty, info, NULL);
- if (tty->termios->c_cflag & CBAUD) {
+ if (tty->termios.c_cflag & CBAUD) {
sSetDTR(cp);
sSetRTS(cp);
}
@@ -1089,35 +1089,35 @@
if (rocket_paranoia_check(info, "rp_set_termios"))
return;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
/*
* This driver doesn't support CS5 or CS6
*/
if (((cflag & CSIZE) == CS5) || ((cflag & CSIZE) == CS6))
- tty->termios->c_cflag =
+ tty->termios.c_cflag =
((cflag & ~CSIZE) | (old_termios->c_cflag & CSIZE));
/* Or CMSPAR */
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
configure_r_port(tty, info, old_termios);
cp = &info->channel;
/* Handle transition to B0 status */
- if ((old_termios->c_cflag & CBAUD) && !(tty->termios->c_cflag & CBAUD)) {
+ if ((old_termios->c_cflag & CBAUD) && !(tty->termios.c_cflag & CBAUD)) {
sClrDTR(cp);
sClrRTS(cp);
}
/* Handle transition away from B0 status */
- if (!(old_termios->c_cflag & CBAUD) && (tty->termios->c_cflag & CBAUD)) {
- if (!tty->hw_stopped || !(tty->termios->c_cflag & CRTSCTS))
+ if (!(old_termios->c_cflag & CBAUD) && (tty->termios.c_cflag & CBAUD)) {
+ if (!tty->hw_stopped || !(tty->termios.c_cflag & CRTSCTS))
sSetRTS(cp);
sSetDTR(cp);
}
- if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios->c_cflag & CRTSCTS)) {
+ if ((old_termios->c_cflag & CRTSCTS) && !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
rp_start(tty);
}
diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250.c
index 8123f78..44f52c6 100644
--- a/drivers/tty/serial/8250/8250.c
+++ b/drivers/tty/serial/8250/8250.c
@@ -2202,6 +2202,7 @@
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
+ int fifo_bug = 0;
switch (termios->c_cflag & CSIZE) {
case CS5:
@@ -2221,8 +2222,11 @@
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
- if (termios->c_cflag & PARENB)
+ if (termios->c_cflag & PARENB) {
cval |= UART_LCR_PARITY;
+ if (up->bugs & UART_BUG_PARITY)
+ fifo_bug = 1;
+ }
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
#ifdef CMSPAR
@@ -2246,7 +2250,7 @@
if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
fcr = uart_config[port->type].fcr;
- if (baud < 2400) {
+ if (baud < 2400 || fifo_bug) {
fcr &= ~UART_FCR_TRIGGER_MASK;
fcr |= UART_FCR_TRIGGER_1;
}
@@ -2979,36 +2983,36 @@
static int __devinit serial8250_probe(struct platform_device *dev)
{
struct plat_serial8250_port *p = dev->dev.platform_data;
- struct uart_port port;
+ struct uart_8250_port uart;
int ret, i, irqflag = 0;
- memset(&port, 0, sizeof(struct uart_port));
+ memset(&uart, 0, sizeof(uart));
if (share_irqs)
irqflag = IRQF_SHARED;
for (i = 0; p && p->flags != 0; p++, i++) {
- port.iobase = p->iobase;
- port.membase = p->membase;
- port.irq = p->irq;
- port.irqflags = p->irqflags;
- port.uartclk = p->uartclk;
- port.regshift = p->regshift;
- port.iotype = p->iotype;
- port.flags = p->flags;
- port.mapbase = p->mapbase;
- port.hub6 = p->hub6;
- port.private_data = p->private_data;
- port.type = p->type;
- port.serial_in = p->serial_in;
- port.serial_out = p->serial_out;
- port.handle_irq = p->handle_irq;
- port.handle_break = p->handle_break;
- port.set_termios = p->set_termios;
- port.pm = p->pm;
- port.dev = &dev->dev;
- port.irqflags |= irqflag;
- ret = serial8250_register_port(&port);
+ uart.port.iobase = p->iobase;
+ uart.port.membase = p->membase;
+ uart.port.irq = p->irq;
+ uart.port.irqflags = p->irqflags;
+ uart.port.uartclk = p->uartclk;
+ uart.port.regshift = p->regshift;
+ uart.port.iotype = p->iotype;
+ uart.port.flags = p->flags;
+ uart.port.mapbase = p->mapbase;
+ uart.port.hub6 = p->hub6;
+ uart.port.private_data = p->private_data;
+ uart.port.type = p->type;
+ uart.port.serial_in = p->serial_in;
+ uart.port.serial_out = p->serial_out;
+ uart.port.handle_irq = p->handle_irq;
+ uart.port.handle_break = p->handle_break;
+ uart.port.set_termios = p->set_termios;
+ uart.port.pm = p->pm;
+ uart.port.dev = &dev->dev;
+ uart.port.irqflags |= irqflag;
+ ret = serial8250_register_8250_port(&uart);
if (ret < 0) {
dev_err(&dev->dev, "unable to register port at index %d "
"(IO%lx MEM%llx IRQ%d): %d\n", i,
@@ -3081,7 +3085,7 @@
static struct platform_device *serial8250_isa_devs;
/*
- * serial8250_register_port and serial8250_unregister_port allows for
+ * serial8250_register_8250_port and serial8250_unregister_port allows for
* 16x50 serial ports to be configured at run-time, to support PCMCIA
* modems and PCI multiport cards.
*/
@@ -3155,6 +3159,7 @@
uart->port.regshift = up->port.regshift;
uart->port.iotype = up->port.iotype;
uart->port.flags = up->port.flags | UPF_BOOT_AUTOCONF;
+ uart->bugs = up->bugs;
uart->port.mapbase = up->port.mapbase;
uart->port.private_data = up->port.private_data;
if (up->port.dev)
@@ -3198,29 +3203,6 @@
EXPORT_SYMBOL(serial8250_register_8250_port);
/**
- * serial8250_register_port - register a serial port
- * @port: serial port template
- *
- * Configure the serial port specified by the request. If the
- * port exists and is in use, it is hung up and unregistered
- * first.
- *
- * The port is then probed and if necessary the IRQ is autodetected
- * If this fails an error is returned.
- *
- * On success the port is ready to use and the line number is returned.
- */
-int serial8250_register_port(struct uart_port *port)
-{
- struct uart_8250_port up;
-
- memset(&up, 0, sizeof(up));
- memcpy(&up.port, port, sizeof(*port));
- return serial8250_register_8250_port(&up);
-}
-EXPORT_SYMBOL(serial8250_register_port);
-
-/**
* serial8250_unregister_port - remove a 16x50 serial port at runtime
* @line: serial line number
*
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index f9719d1..972b521 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -13,36 +13,6 @@
#include <linux/serial_8250.h>
-struct uart_8250_port {
- struct uart_port port;
- struct timer_list timer; /* "no irq" timer */
- struct list_head list; /* ports on this IRQ */
- unsigned short capabilities; /* port capabilities */
- unsigned short bugs; /* port bugs */
- unsigned int tx_loadsz; /* transmit fifo load size */
- unsigned char acr;
- unsigned char ier;
- unsigned char lcr;
- unsigned char mcr;
- unsigned char mcr_mask; /* mask of user bits */
- unsigned char mcr_force; /* mask of forced bits */
- unsigned char cur_iotype; /* Running I/O type */
-
- /*
- * Some bits in registers are cleared on a read, so they must
- * be saved whenever the register is read but the bits will not
- * be immediately processed.
- */
-#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
- unsigned char lsr_saved_flags;
-#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
- unsigned char msr_saved_flags;
-
- /* 8250 specific callbacks */
- int (*dl_read)(struct uart_8250_port *);
- void (*dl_write)(struct uart_8250_port *, int);
-};
-
struct old_serial_port {
unsigned int uart;
unsigned int baud_base;
@@ -78,6 +48,7 @@
#define UART_BUG_TXEN (1 << 1) /* UART has buggy TX IIR status */
#define UART_BUG_NOMSR (1 << 2) /* UART has buggy MSR status bits (Au1x00) */
#define UART_BUG_THRE (1 << 3) /* UART has buggy THRE reassertion */
+#define UART_BUG_PARITY (1 << 4) /* UART mishandles parity if FIFO enabled */
#define PROBE_RSA (1 << 0)
#define PROBE_ANY (~0)
diff --git a/drivers/tty/serial/8250/8250_acorn.c b/drivers/tty/serial/8250/8250_acorn.c
index b0ce8c5..8574983 100644
--- a/drivers/tty/serial/8250/8250_acorn.c
+++ b/drivers/tty/serial/8250/8250_acorn.c
@@ -43,7 +43,7 @@
{
struct serial_card_info *info;
struct serial_card_type *type = id->data;
- struct uart_port port;
+ struct uart_8250_port uart;
unsigned long bus_addr;
unsigned int i;
@@ -62,19 +62,19 @@
ecard_set_drvdata(ec, info);
- memset(&port, 0, sizeof(struct uart_port));
- port.irq = ec->irq;
- port.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
- port.uartclk = type->uartclk;
- port.iotype = UPIO_MEM;
- port.regshift = 2;
- port.dev = &ec->dev;
+ memset(&uart, 0, sizeof(struct uart_8250_port));
+ uart.port.irq = ec->irq;
+ uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ uart.port.uartclk = type->uartclk;
+ uart.port.iotype = UPIO_MEM;
+ uart.port.regshift = 2;
+ uart.port.dev = &ec->dev;
for (i = 0; i < info->num_ports; i ++) {
- port.membase = info->vaddr + type->offset[i];
- port.mapbase = bus_addr + type->offset[i];
+ uart.port.membase = info->vaddr + type->offset[i];
+ uart.port.mapbase = bus_addr + type->offset[i];
- info->ports[i] = serial8250_register_port(&port);
+ info->ports[i] = serial8250_register_8250_port(&uart);
}
return 0;
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index f574eef..c3b2ec0 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -89,7 +89,7 @@
static int __devinit dw8250_probe(struct platform_device *pdev)
{
- struct uart_port port = {};
+ struct uart_8250_port uart = {};
struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
struct device_node *np = pdev->dev.of_node;
@@ -104,28 +104,28 @@
data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
- port.private_data = data;
+ uart.port.private_data = data;
- spin_lock_init(&port.lock);
- port.mapbase = regs->start;
- port.irq = irq->start;
- port.handle_irq = dw8250_handle_irq;
- port.type = PORT_8250;
- port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP |
+ spin_lock_init(&uart.port.lock);
+ uart.port.mapbase = regs->start;
+ uart.port.irq = irq->start;
+ uart.port.handle_irq = dw8250_handle_irq;
+ uart.port.type = PORT_8250;
+ uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP |
UPF_FIXED_PORT | UPF_FIXED_TYPE;
- port.dev = &pdev->dev;
+ uart.port.dev = &pdev->dev;
- port.iotype = UPIO_MEM;
- port.serial_in = dw8250_serial_in;
- port.serial_out = dw8250_serial_out;
+ uart.port.iotype = UPIO_MEM;
+ uart.port.serial_in = dw8250_serial_in;
+ uart.port.serial_out = dw8250_serial_out;
if (!of_property_read_u32(np, "reg-io-width", &val)) {
switch (val) {
case 1:
break;
case 4:
- port.iotype = UPIO_MEM32;
- port.serial_in = dw8250_serial_in32;
- port.serial_out = dw8250_serial_out32;
+ uart.port.iotype = UPIO_MEM32;
+ uart.port.serial_in = dw8250_serial_in32;
+ uart.port.serial_out = dw8250_serial_out32;
break;
default:
dev_err(&pdev->dev, "unsupported reg-io-width (%u)\n",
@@ -135,15 +135,15 @@
}
if (!of_property_read_u32(np, "reg-shift", &val))
- port.regshift = val;
+ uart.port.regshift = val;
if (of_property_read_u32(np, "clock-frequency", &val)) {
dev_err(&pdev->dev, "no clock-frequency property set\n");
return -EINVAL;
}
- port.uartclk = val;
+ uart.port.uartclk = val;
- data->line = serial8250_register_port(&port);
+ data->line = serial8250_register_8250_port(&uart);
if (data->line < 0)
return data->line;
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index d8c0ffb..097dff9 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -26,7 +26,7 @@
static int __init serial_init_chip(struct parisc_device *dev)
{
- struct uart_port port;
+ struct uart_8250_port uart;
unsigned long address;
int err;
@@ -48,21 +48,21 @@
if (dev->id.sversion != 0x8d)
address += 0x800;
- memset(&port, 0, sizeof(port));
- port.iotype = UPIO_MEM;
+ memset(&uart, 0, sizeof(uart));
+ uart.port.iotype = UPIO_MEM;
/* 7.272727MHz on Lasi. Assumed the same for Dino, Wax and Timi. */
- port.uartclk = 7272727;
- port.mapbase = address;
- port.membase = ioremap_nocache(address, 16);
- port.irq = dev->irq;
- port.flags = UPF_BOOT_AUTOCONF;
- port.dev = &dev->dev;
+ uart.port.uartclk = 7272727;
+ uart.port.mapbase = address;
+ uart.port.membase = ioremap_nocache(address, 16);
+ uart.port.irq = dev->irq;
+ uart.port.flags = UPF_BOOT_AUTOCONF;
+ uart.port.dev = &dev->dev;
- err = serial8250_register_port(&port);
+ err = serial8250_register_8250_port(&uart);
if (err < 0) {
printk(KERN_WARNING
- "serial8250_register_port returned error %d\n", err);
- iounmap(port.membase);
+ "serial8250_register_8250_port returned error %d\n", err);
+ iounmap(uart.port.membase);
return err;
}
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index c13438c9..8f1dd2c 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -171,7 +171,7 @@
return 0;
}
#endif
- memset(&port, 0, sizeof(struct uart_port));
+ memset(&uart, 0, sizeof(uart));
/* Memory mapped I/O */
port.iotype = UPIO_MEM;
@@ -182,7 +182,7 @@
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 1;
port.dev = &d->dev;
- line = serial8250_register_port(&port);
+ line = serial8250_register_8250_port(&uart);
if (line < 0) {
printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
@@ -210,7 +210,7 @@
#ifdef CONFIG_HPAPCI
int line;
unsigned long base;
- struct uart_port uport;
+ struct uart_8250_port uart;
struct hp300_port *port;
int i;
#endif
@@ -248,26 +248,26 @@
if (!port)
return -ENOMEM;
- memset(&uport, 0, sizeof(struct uart_port));
+ memset(&uart, 0, sizeof(uart));
base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
/* Memory mapped I/O */
- uport.iotype = UPIO_MEM;
- uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
+ uart.port.iotype = UPIO_MEM;
+ uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
| UPF_BOOT_AUTOCONF;
/* XXX - no interrupt support yet */
- uport.irq = 0;
- uport.uartclk = HPAPCI_BAUD_BASE * 16;
- uport.mapbase = base;
- uport.membase = (char *)(base + DIO_VIRADDRBASE);
- uport.regshift = 2;
+ uart.port.irq = 0;
+ uart.port.uartclk = HPAPCI_BAUD_BASE * 16;
+ uart.port.mapbase = base;
+ uart.port.membase = (char *)(base + DIO_VIRADDRBASE);
+ uart.port.regshift = 2;
- line = serial8250_register_port(&uport);
+ line = serial8250_register_8250_port(&uart);
if (line < 0) {
printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
- " %d irq %d failed\n", i, uport.irq);
+ " %d irq %d failed\n", i, uart.port.irq);
kfree(port);
continue;
}
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 28e7c7c..62e10fe 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -44,7 +44,7 @@
int (*init)(struct pci_dev *dev);
int (*setup)(struct serial_private *,
const struct pciserial_board *,
- struct uart_port *, int);
+ struct uart_8250_port *, int);
void (*exit)(struct pci_dev *dev);
};
@@ -59,7 +59,7 @@
};
static int pci_default_setup(struct serial_private*,
- const struct pciserial_board*, struct uart_port*, int);
+ const struct pciserial_board*, struct uart_8250_port *, int);
static void moan_device(const char *str, struct pci_dev *dev)
{
@@ -74,7 +74,7 @@
}
static int
-setup_port(struct serial_private *priv, struct uart_port *port,
+setup_port(struct serial_private *priv, struct uart_8250_port *port,
int bar, int offset, int regshift)
{
struct pci_dev *dev = priv->dev;
@@ -93,17 +93,17 @@
if (!priv->remapped_bar[bar])
return -ENOMEM;
- port->iotype = UPIO_MEM;
- port->iobase = 0;
- port->mapbase = base + offset;
- port->membase = priv->remapped_bar[bar] + offset;
- port->regshift = regshift;
+ port->port.iotype = UPIO_MEM;
+ port->port.iobase = 0;
+ port->port.mapbase = base + offset;
+ port->port.membase = priv->remapped_bar[bar] + offset;
+ port->port.regshift = regshift;
} else {
- port->iotype = UPIO_PORT;
- port->iobase = base + offset;
- port->mapbase = 0;
- port->membase = NULL;
- port->regshift = 0;
+ port->port.iotype = UPIO_PORT;
+ port->port.iobase = base + offset;
+ port->port.mapbase = 0;
+ port->port.membase = NULL;
+ port->port.regshift = 0;
}
return 0;
}
@@ -113,7 +113,7 @@
*/
static int addidata_apci7800_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
bar = FL_GET_BASE(board->flags);
@@ -140,7 +140,7 @@
*/
static int
afavlab_setup(struct serial_private *priv, const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -195,7 +195,7 @@
static int
pci_hp_diva_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int offset = board->first_offset;
unsigned int bar = FL_GET_BASE(board->flags);
@@ -370,7 +370,7 @@
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
sbs_setup(struct serial_private *priv, const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -525,7 +525,7 @@
static int pci_siig_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar = FL_GET_BASE(board->flags) + idx, offset = 0;
@@ -619,7 +619,7 @@
static int
pci_timedia_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar = 0, offset = board->first_offset;
@@ -653,7 +653,7 @@
static int
titan_400l_800l_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar, offset = board->first_offset;
@@ -754,7 +754,7 @@
static int
pci_ni8430_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
void __iomem *p;
unsigned long base, len;
@@ -781,7 +781,7 @@
static int pci_netmos_9900_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
unsigned int bar;
@@ -1032,10 +1032,17 @@
return number_uarts;
}
-static int
-pci_default_setup(struct serial_private *priv,
+static int pci_asix_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
+{
+ port->bugs |= UART_BUG_PARITY;
+ return pci_default_setup(priv, board, port, idx);
+}
+
+static int pci_default_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
@@ -1057,15 +1064,15 @@
static int
ce4100_serial_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
int ret;
ret = setup_port(priv, port, 0, 0, board->reg_shift);
- port->iotype = UPIO_MEM32;
- port->type = PORT_XSCALE;
- port->flags = (port->flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
- port->regshift = 2;
+ port->port.iotype = UPIO_MEM32;
+ port->port.type = PORT_XSCALE;
+ port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
+ port->port.regshift = 2;
return ret;
}
@@ -1073,16 +1080,16 @@
static int
pci_omegapci_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
return setup_port(priv, port, 2, idx * 8, 0);
}
static int skip_tx_en_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
- port->flags |= UPF_NO_TXEN_TEST;
+ port->port.flags |= UPF_NO_TXEN_TEST;
printk(KERN_DEBUG "serial8250: skipping TxEn test for device "
"[%04x:%04x] subsystem [%04x:%04x]\n",
priv->dev->vendor,
@@ -1131,11 +1138,11 @@
static int kt_serial_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
- port->flags |= UPF_BUG_THRE;
- port->serial_in = kt_serial_in;
- port->handle_break = kt_handle_break;
+ port->port.flags |= UPF_BUG_THRE;
+ port->port.serial_in = kt_serial_in;
+ port->port.handle_break = kt_handle_break;
return skip_tx_en_setup(priv, board, port, idx);
}
@@ -1151,9 +1158,9 @@
static int
pci_xr17c154_setup(struct serial_private *priv,
const struct pciserial_board *board,
- struct uart_port *port, int idx)
+ struct uart_8250_port *port, int idx)
{
- port->flags |= UPF_EXAR_EFR;
+ port->port.flags |= UPF_EXAR_EFR;
return pci_default_setup(priv, board, port, idx);
}
@@ -1187,6 +1194,7 @@
#define PCIE_DEVICE_ID_NEO_2_OX_IBM 0x00F6
#define PCI_DEVICE_ID_PLX_CRONYX_OMEGA 0xc001
#define PCI_DEVICE_ID_INTEL_PATSBURG_KT 0x1d3d
+#define PCI_VENDOR_ID_ASIX 0x9710
/* Unknown vendors/cards - this should not be in linux/pci_ids.h */
#define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584
@@ -1726,7 +1734,17 @@
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_omegapci_setup,
- },
+ },
+ /*
+ * ASIX devices with FIFO bug
+ */
+ {
+ .vendor = PCI_VENDOR_ID_ASIX,
+ .device = PCI_ANY_ID,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_asix_setup,
+ },
/*
* Default "match everything" terminator entry
*/
@@ -1887,7 +1905,6 @@
pbn_panacom,
pbn_panacom2,
pbn_panacom4,
- pbn_exsys_4055,
pbn_plx_romulus,
pbn_oxsemi,
pbn_oxsemi_1_4000000,
@@ -2393,13 +2410,6 @@
.reg_shift = 7,
},
- [pbn_exsys_4055] = {
- .flags = FL_BASE2,
- .num_ports = 4,
- .base_baud = 115200,
- .uart_offset = 8,
- },
-
/* I think this entry is broken - the first_offset looks wrong --rmk */
[pbn_plx_romulus] = {
.flags = FL_BASE2,
@@ -2728,7 +2738,7 @@
struct serial_private *
pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board)
{
- struct uart_port serial_port;
+ struct uart_8250_port uart;
struct serial_private *priv;
struct pci_serial_quirk *quirk;
int rc, nr_ports, i;
@@ -2768,22 +2778,22 @@
priv->dev = dev;
priv->quirk = quirk;
- memset(&serial_port, 0, sizeof(struct uart_port));
- serial_port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
- serial_port.uartclk = board->base_baud * 16;
- serial_port.irq = get_pci_irq(dev, board);
- serial_port.dev = &dev->dev;
+ memset(&uart, 0, sizeof(uart));
+ uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ uart.port.uartclk = board->base_baud * 16;
+ uart.port.irq = get_pci_irq(dev, board);
+ uart.port.dev = &dev->dev;
for (i = 0; i < nr_ports; i++) {
- if (quirk->setup(priv, board, &serial_port, i))
+ if (quirk->setup(priv, board, &uart, i))
break;
#ifdef SERIAL_DEBUG_PCI
printk(KERN_DEBUG "Setup PCI port: port %lx, irq %d, type %d\n",
- serial_port.iobase, serial_port.irq, serial_port.iotype);
+ uart.port.iobase, uart.port.irq, uart.port.iotype);
#endif
- priv->line[i] = serial8250_register_port(&serial_port);
+ priv->line[i] = serial8250_register_8250_port(&uart);
if (priv->line[i] < 0) {
printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), priv->line[i]);
break;
@@ -3193,7 +3203,7 @@
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_EXSYS,
PCI_SUBDEVICE_ID_EXSYS_4055, 0, 0,
- pbn_exsys_4055 },
+ pbn_b2_4_115200 },
/*
* Megawolf Romulus PCI Serial Card, from Mike Hudson
* (Exoray@isys.ca)
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index a2f2365..fde5aa6 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -424,7 +424,7 @@
static int __devinit
serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
{
- struct uart_port port;
+ struct uart_8250_port uart;
int ret, line, flags = dev_id->driver_data;
if (flags & UNKNOWN_DEV) {
@@ -433,32 +433,32 @@
return ret;
}
- memset(&port, 0, sizeof(struct uart_port));
+ memset(&uart, 0, sizeof(uart));
if (pnp_irq_valid(dev, 0))
- port.irq = pnp_irq(dev, 0);
+ uart.port.irq = pnp_irq(dev, 0);
if (pnp_port_valid(dev, 0)) {
- port.iobase = pnp_port_start(dev, 0);
- port.iotype = UPIO_PORT;
+ uart.port.iobase = pnp_port_start(dev, 0);
+ uart.port.iotype = UPIO_PORT;
} else if (pnp_mem_valid(dev, 0)) {
- port.mapbase = pnp_mem_start(dev, 0);
- port.iotype = UPIO_MEM;
- port.flags = UPF_IOREMAP;
+ uart.port.mapbase = pnp_mem_start(dev, 0);
+ uart.port.iotype = UPIO_MEM;
+ uart.port.flags = UPF_IOREMAP;
} else
return -ENODEV;
#ifdef SERIAL_DEBUG_PNP
printk(KERN_DEBUG
"Setup PNP port: port %x, mem 0x%lx, irq %d, type %d\n",
- port.iobase, port.mapbase, port.irq, port.iotype);
+ uart.port.iobase, uart.port.mapbase, uart.port.irq, uart.port.iotype);
#endif
- port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+ uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
- port.flags |= UPF_SHARE_IRQ;
- port.uartclk = 1843200;
- port.dev = &dev->dev;
+ uart.port.flags |= UPF_SHARE_IRQ;
+ uart.port.uartclk = 1843200;
+ uart.port.dev = &dev->dev;
- line = serial8250_register_port(&port);
+ line = serial8250_register_8250_port(&uart);
if (line < 0)
return -ENODEV;
diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c
index 29b695d..b7d48b3 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -73,7 +73,7 @@
unsigned int prodid;
int multi; /* 1 = multifunction, > 1 = # ports */
void (*config)(struct pcmcia_device *);
- void (*setup)(struct pcmcia_device *, struct uart_port *);
+ void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
void (*wakeup)(struct pcmcia_device *);
int (*post)(struct pcmcia_device *);
};
@@ -105,9 +105,9 @@
* Elan VPU16551 UART with 14.7456MHz oscillator
* manfid 0x015D, 0x4C45
*/
-static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port)
+static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
{
- port->uartclk = 14745600;
+ uart->port.uartclk = 14745600;
}
static int quirk_post_ibm(struct pcmcia_device *link)
@@ -343,25 +343,25 @@
static int setup_serial(struct pcmcia_device *handle, struct serial_info * info,
unsigned int iobase, int irq)
{
- struct uart_port port;
+ struct uart_8250_port uart;
int line;
- memset(&port, 0, sizeof (struct uart_port));
- port.iobase = iobase;
- port.irq = irq;
- port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
- port.uartclk = 1843200;
- port.dev = &handle->dev;
+ memset(&uart, 0, sizeof(uart));
+ uart.port.iobase = iobase;
+ uart.port.irq = irq;
+ uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
+ uart.port.uartclk = 1843200;
+ uart.port.dev = &handle->dev;
if (buggy_uart)
- port.flags |= UPF_BUGGY_UART;
+ uart.port.flags |= UPF_BUGGY_UART;
if (info->quirk && info->quirk->setup)
- info->quirk->setup(handle, &port);
+ info->quirk->setup(handle, &uart);
- line = serial8250_register_port(&port);
+ line = serial8250_register_8250_port(&uart);
if (line < 0) {
- printk(KERN_NOTICE "serial_cs: serial8250_register_port() at "
- "0x%04lx, irq %d failed\n", (u_long)iobase, irq);
+ pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
+ (unsigned long)iobase, irq);
return -EINVAL;
}
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 070b442..0020786 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -704,6 +704,25 @@
If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
and you want to use serial console, say Y. Otherwise, say N.
+config SERIAL_HS_LPC32XX
+ tristate "LPC32XX high speed serial port support"
+ depends on ARCH_LPC32XX && OF
+ select SERIAL_CORE
+ help
+ Support for the LPC32XX high speed serial ports (up to 900kbps).
+ Those are UARTs completely different from the Standard UARTs on the
+ LPC32XX SoC.
+ Choose M or Y here to build this driver.
+
+config SERIAL_HS_LPC32XX_CONSOLE
+ bool "Enable LPC32XX high speed UART serial console"
+ depends on SERIAL_HS_LPC32XX
+ select SERIAL_CORE_CONSOLE
+ help
+ If you would like to be able to use one of the high speed serial
+ ports on the LPC32XX as the console, you can do so by answering
+ Y to this option.
+
config SERIAL_CORE
tristate
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 7257c5d..8a5df38 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -34,6 +34,7 @@
obj-$(CONFIG_SERIAL_68328) += 68328serial.o
obj-$(CONFIG_SERIAL_MCF) += mcf.o
obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
+obj-$(CONFIG_SERIAL_HS_LPC32XX) += lpc32xx_hs.o
obj-$(CONFIG_SERIAL_DZ) += dz.o
obj-$(CONFIG_SERIAL_ZS) += zs.o
obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index d3553b5..92b1ac8 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1215,14 +1215,14 @@
return IRQ_RETVAL(handled);
}
-static unsigned int pl01x_tx_empty(struct uart_port *port)
+static unsigned int pl011_tx_empty(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int status = readw(uap->port.membase + UART01x_FR);
return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
}
-static unsigned int pl01x_get_mctrl(struct uart_port *port)
+static unsigned int pl011_get_mctrl(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int result = 0;
@@ -1285,7 +1285,7 @@
}
#ifdef CONFIG_CONSOLE_POLL
-static int pl010_get_poll_char(struct uart_port *port)
+static int pl011_get_poll_char(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int status;
@@ -1297,7 +1297,7 @@
return readw(uap->port.membase + UART01x_DR);
}
-static void pl010_put_poll_char(struct uart_port *port,
+static void pl011_put_poll_char(struct uart_port *port,
unsigned char ch)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
@@ -1637,7 +1637,7 @@
/*
* Release the memory region(s) being used by 'port'
*/
-static void pl010_release_port(struct uart_port *port)
+static void pl011_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase, SZ_4K);
}
@@ -1645,7 +1645,7 @@
/*
* Request the memory region(s) being used by 'port'
*/
-static int pl010_request_port(struct uart_port *port)
+static int pl011_request_port(struct uart_port *port)
{
return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
!= NULL ? 0 : -EBUSY;
@@ -1654,18 +1654,18 @@
/*
* Configure/autoconfigure the port.
*/
-static void pl010_config_port(struct uart_port *port, int flags)
+static void pl011_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE) {
port->type = PORT_AMBA;
- pl010_request_port(port);
+ pl011_request_port(port);
}
}
/*
* verify the new serial_struct (for TIOCSSERIAL).
*/
-static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
+static int pl011_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
@@ -1678,9 +1678,9 @@
}
static struct uart_ops amba_pl011_pops = {
- .tx_empty = pl01x_tx_empty,
+ .tx_empty = pl011_tx_empty,
.set_mctrl = pl011_set_mctrl,
- .get_mctrl = pl01x_get_mctrl,
+ .get_mctrl = pl011_get_mctrl,
.stop_tx = pl011_stop_tx,
.start_tx = pl011_start_tx,
.stop_rx = pl011_stop_rx,
@@ -1691,13 +1691,13 @@
.flush_buffer = pl011_dma_flush_buffer,
.set_termios = pl011_set_termios,
.type = pl011_type,
- .release_port = pl010_release_port,
- .request_port = pl010_request_port,
- .config_port = pl010_config_port,
- .verify_port = pl010_verify_port,
+ .release_port = pl011_release_port,
+ .request_port = pl011_request_port,
+ .config_port = pl011_config_port,
+ .verify_port = pl011_verify_port,
#ifdef CONFIG_CONSOLE_POLL
- .poll_get_char = pl010_get_poll_char,
- .poll_put_char = pl010_put_poll_char,
+ .poll_get_char = pl011_get_poll_char,
+ .poll_put_char = pl011_put_poll_char,
#endif
};
diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index bd97db2..9242d56 100644
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -182,7 +182,7 @@
* To avoid losting RX interrupt, we reset IR function
* before sending data.
*/
- if (tty->termios->c_line == N_IRDA)
+ if (tty->termios.c_line == N_IRDA)
bfin_serial_reset_irda(port);
#ifdef CONFIG_SERIAL_BFIN_DMA
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index 80b6b1b..6b705b2 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -955,7 +955,7 @@
/* Calculate the chartime depending on baudrate, numbor of bits etc. */
static void update_char_time(struct e100_serial * info)
{
- tcflag_t cflags = info->port.tty->termios->c_cflag;
+ tcflag_t cflags = info->port.tty->termios.c_cflag;
int bits;
/* calc. number of bits / data byte */
@@ -1473,7 +1473,7 @@
xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char,
STOP_CHAR(info->port.tty));
xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop);
- if (tty->termios->c_iflag & IXON ) {
+ if (tty->termios.c_iflag & IXON ) {
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
}
@@ -1496,7 +1496,7 @@
info->xmit.tail,SERIAL_XMIT_SIZE)));
xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty));
xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
- if (tty->termios->c_iflag & IXON ) {
+ if (tty->termios.c_iflag & IXON ) {
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
}
@@ -2929,7 +2929,7 @@
descr[i].buf = 0;
}
- if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL)) {
+ if (!info->port.tty || (info->port.tty->termios.c_cflag & HUPCL)) {
/* hang up DTR and RTS if HUPCL is enabled */
e100_dtr(info, 0);
e100_rts(info, 0); /* could check CRTSCTS before doing this */
@@ -2953,12 +2953,12 @@
unsigned long flags;
/* first some safety checks */
- if (!info->port.tty || !info->port.tty->termios)
+ if (!info->port.tty)
return;
if (!info->ioport)
return;
- cflag = info->port.tty->termios->c_cflag;
+ cflag = info->port.tty->termios.c_cflag;
/* possibly, the tx/rx should be disabled first to do this safely */
@@ -3088,7 +3088,7 @@
info->ioport[REG_REC_CTRL] = info->rx_ctrl;
xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty));
xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
- if (info->port.tty->termios->c_iflag & IXON ) {
+ if (info->port.tty->termios.c_iflag & IXON ) {
DFLOW(DEBUG_LOG(info->line, "FLOW XOFF enabled 0x%02X\n",
STOP_CHAR(info->port.tty)));
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
@@ -3355,7 +3355,7 @@
DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty)));
/* Do RTS before XOFF since XOFF might take some time */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
/* Turn off RTS line */
e100_rts(info, 0);
}
@@ -3377,7 +3377,7 @@
DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty)));
DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count));
/* Do RTS before XOFF since XOFF might take some time */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
/* Assert RTS line */
e100_rts(info, 1);
}
@@ -3748,7 +3748,7 @@
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
rs_start(tty);
}
@@ -3815,7 +3815,7 @@
* separate termios for callout and dialin.
*/
if (info->flags & ASYNC_NORMAL_ACTIVE)
- info->normal_termios = *tty->termios;
+ info->normal_termios = tty->termios;
/*
* Now we wait for the transmit buffer to clear; and we notify
* the line discipline to only process XON/XOFF characters.
@@ -3998,7 +3998,7 @@
return 0;
}
- if (tty->termios->c_cflag & CLOCAL) {
+ if (tty->termios.c_cflag & CLOCAL) {
do_clocal = 1;
}
@@ -4219,7 +4219,7 @@
}
if ((info->count == 1) && (info->flags & ASYNC_SPLIT_TERMIOS)) {
- *tty->termios = info->normal_termios;
+ tty->termios = info->normal_termios;
change_speed(info);
}
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index d5c689d6..20e9117 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -206,7 +206,7 @@
unsigned short trcv_delay; /* transceiver delay */
struct clk *clk_ipg;
struct clk *clk_per;
- struct imx_uart_data *devdata;
+ const struct imx_uart_data *devdata;
};
struct imx_port_ucrs {
diff --git a/drivers/tty/serial/ioc4_serial.c b/drivers/tty/serial/ioc4_serial.c
index e16894f..cc5aca7 100644
--- a/drivers/tty/serial/ioc4_serial.c
+++ b/drivers/tty/serial/ioc4_serial.c
@@ -1803,7 +1803,7 @@
ioc4_set_proto(port, the_port->mapbase);
/* set the speed of the serial port */
- ioc4_change_speed(the_port, state->port.tty->termios,
+ ioc4_change_speed(the_port, &state->port.tty->termios,
(struct ktermios *)0);
return 0;
diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c
index 434bd88..7139796 100644
--- a/drivers/tty/serial/jsm/jsm_tty.c
+++ b/drivers/tty/serial/jsm/jsm_tty.c
@@ -161,7 +161,7 @@
struct ktermios *termios;
spin_lock_irqsave(&port->lock, lock_flags);
- termios = port->state->port.tty->termios;
+ termios = &port->state->port.tty->termios;
if (ch == termios->c_cc[VSTART])
channel->ch_bd->bd_ops->send_start_character(channel);
@@ -250,7 +250,7 @@
channel->ch_cached_lsr = 0;
channel->ch_stops_sent = 0;
- termios = port->state->port.tty->termios;
+ termios = &port->state->port.tty->termios;
channel->ch_c_cflag = termios->c_cflag;
channel->ch_c_iflag = termios->c_iflag;
channel->ch_c_oflag = termios->c_oflag;
@@ -283,7 +283,7 @@
jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev, "start\n");
bd = channel->ch_bd;
- ts = port->state->port.tty->termios;
+ ts = &port->state->port.tty->termios;
channel->ch_flags &= ~(CH_STOPI);
@@ -567,7 +567,7 @@
*input data and return immediately.
*/
if (!tp ||
- !(tp->termios->c_cflag & CREAD) ) {
+ !(tp->termios.c_cflag & CREAD) ) {
jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
"input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum);
diff --git a/drivers/tty/serial/lpc32xx_hs.c b/drivers/tty/serial/lpc32xx_hs.c
new file mode 100644
index 0000000..ba3af3b
--- /dev/null
+++ b/drivers/tty/serial/lpc32xx_hs.c
@@ -0,0 +1,823 @@
+/*
+ * High Speed Serial Ports on NXP LPC32xx SoC
+ *
+ * Authors: Kevin Wells <kevin.wells@nxp.com>
+ * Roland Stigge <stigge@antcom.de>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ * Copyright (C) 2012 Roland Stigge
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/nmi.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <mach/platform.h>
+#include <mach/hardware.h>
+
+/*
+ * High Speed UART register offsets
+ */
+#define LPC32XX_HSUART_FIFO(x) ((x) + 0x00)
+#define LPC32XX_HSUART_LEVEL(x) ((x) + 0x04)
+#define LPC32XX_HSUART_IIR(x) ((x) + 0x08)
+#define LPC32XX_HSUART_CTRL(x) ((x) + 0x0C)
+#define LPC32XX_HSUART_RATE(x) ((x) + 0x10)
+
+#define LPC32XX_HSU_BREAK_DATA (1 << 10)
+#define LPC32XX_HSU_ERROR_DATA (1 << 9)
+#define LPC32XX_HSU_RX_EMPTY (1 << 8)
+
+#define LPC32XX_HSU_TX_LEV(n) (((n) >> 8) & 0xFF)
+#define LPC32XX_HSU_RX_LEV(n) ((n) & 0xFF)
+
+#define LPC32XX_HSU_TX_INT_SET (1 << 6)
+#define LPC32XX_HSU_RX_OE_INT (1 << 5)
+#define LPC32XX_HSU_BRK_INT (1 << 4)
+#define LPC32XX_HSU_FE_INT (1 << 3)
+#define LPC32XX_HSU_RX_TIMEOUT_INT (1 << 2)
+#define LPC32XX_HSU_RX_TRIG_INT (1 << 1)
+#define LPC32XX_HSU_TX_INT (1 << 0)
+
+#define LPC32XX_HSU_HRTS_INV (1 << 21)
+#define LPC32XX_HSU_HRTS_TRIG_8B (0x0 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_16B (0x1 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_32B (0x2 << 19)
+#define LPC32XX_HSU_HRTS_TRIG_48B (0x3 << 19)
+#define LPC32XX_HSU_HRTS_EN (1 << 18)
+#define LPC32XX_HSU_TMO_DISABLED (0x0 << 16)
+#define LPC32XX_HSU_TMO_INACT_4B (0x1 << 16)
+#define LPC32XX_HSU_TMO_INACT_8B (0x2 << 16)
+#define LPC32XX_HSU_TMO_INACT_16B (0x3 << 16)
+#define LPC32XX_HSU_HCTS_INV (1 << 15)
+#define LPC32XX_HSU_HCTS_EN (1 << 14)
+#define LPC32XX_HSU_OFFSET(n) ((n) << 9)
+#define LPC32XX_HSU_BREAK (1 << 8)
+#define LPC32XX_HSU_ERR_INT_EN (1 << 7)
+#define LPC32XX_HSU_RX_INT_EN (1 << 6)
+#define LPC32XX_HSU_TX_INT_EN (1 << 5)
+#define LPC32XX_HSU_RX_TL1B (0x0 << 2)
+#define LPC32XX_HSU_RX_TL4B (0x1 << 2)
+#define LPC32XX_HSU_RX_TL8B (0x2 << 2)
+#define LPC32XX_HSU_RX_TL16B (0x3 << 2)
+#define LPC32XX_HSU_RX_TL32B (0x4 << 2)
+#define LPC32XX_HSU_RX_TL48B (0x5 << 2)
+#define LPC32XX_HSU_TX_TLEMPTY (0x0 << 0)
+#define LPC32XX_HSU_TX_TL0B (0x0 << 0)
+#define LPC32XX_HSU_TX_TL4B (0x1 << 0)
+#define LPC32XX_HSU_TX_TL8B (0x2 << 0)
+#define LPC32XX_HSU_TX_TL16B (0x3 << 0)
+
+#define MODNAME "lpc32xx_hsuart"
+
+struct lpc32xx_hsuart_port {
+ struct uart_port port;
+};
+
+#define FIFO_READ_LIMIT 128
+#define MAX_PORTS 3
+#define LPC32XX_TTY_NAME "ttyTX"
+static struct lpc32xx_hsuart_port lpc32xx_hs_ports[MAX_PORTS];
+
+#ifdef CONFIG_SERIAL_HS_LPC32XX_CONSOLE
+static void wait_for_xmit_empty(struct uart_port *port)
+{
+ unsigned int timeout = 10000;
+
+ do {
+ if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(
+ port->membase))) == 0)
+ break;
+ if (--timeout == 0)
+ break;
+ udelay(1);
+ } while (1);
+}
+
+static void wait_for_xmit_ready(struct uart_port *port)
+{
+ unsigned int timeout = 10000;
+
+ while (1) {
+ if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(
+ port->membase))) < 32)
+ break;
+ if (--timeout == 0)
+ break;
+ udelay(1);
+ }
+}
+
+static void lpc32xx_hsuart_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmit_ready(port);
+ writel((u32)ch, LPC32XX_HSUART_FIFO(port->membase));
+}
+
+static void lpc32xx_hsuart_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct lpc32xx_hsuart_port *up = &lpc32xx_hs_ports[co->index];
+ unsigned long flags;
+ int locked = 1;
+
+ touch_nmi_watchdog();
+ local_irq_save(flags);
+ if (up->port.sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock(&up->port.lock);
+ else
+ spin_lock(&up->port.lock);
+
+ uart_console_write(&up->port, s, count, lpc32xx_hsuart_console_putchar);
+ wait_for_xmit_empty(&up->port);
+
+ if (locked)
+ spin_unlock(&up->port.lock);
+ local_irq_restore(flags);
+}
+
+static int __init lpc32xx_hsuart_console_setup(struct console *co,
+ char *options)
+{
+ struct uart_port *port;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index >= MAX_PORTS)
+ co->index = 0;
+
+ port = &lpc32xx_hs_ports[co->index].port;
+ if (!port->membase)
+ return -ENODEV;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver lpc32xx_hsuart_reg;
+static struct console lpc32xx_hsuart_console = {
+ .name = LPC32XX_TTY_NAME,
+ .write = lpc32xx_hsuart_console_write,
+ .device = uart_console_device,
+ .setup = lpc32xx_hsuart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &lpc32xx_hsuart_reg,
+};
+
+static int __init lpc32xx_hsuart_console_init(void)
+{
+ register_console(&lpc32xx_hsuart_console);
+ return 0;
+}
+console_initcall(lpc32xx_hsuart_console_init);
+
+#define LPC32XX_HSUART_CONSOLE (&lpc32xx_hsuart_console)
+#else
+#define LPC32XX_HSUART_CONSOLE NULL
+#endif
+
+static struct uart_driver lpc32xx_hs_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = MODNAME,
+ .dev_name = LPC32XX_TTY_NAME,
+ .nr = MAX_PORTS,
+ .cons = LPC32XX_HSUART_CONSOLE,
+};
+static int uarts_registered;
+
+static unsigned int __serial_get_clock_div(unsigned long uartclk,
+ unsigned long rate)
+{
+ u32 div, goodrate, hsu_rate, l_hsu_rate, comprate;
+ u32 rate_diff;
+
+ /* Find the closest divider to get the desired clock rate */
+ div = uartclk / rate;
+ goodrate = hsu_rate = (div / 14) - 1;
+ if (hsu_rate != 0)
+ hsu_rate--;
+
+ /* Tweak divider */
+ l_hsu_rate = hsu_rate + 3;
+ rate_diff = 0xFFFFFFFF;
+
+ while (hsu_rate < l_hsu_rate) {
+ comprate = uartclk / ((hsu_rate + 1) * 14);
+ if (abs(comprate - rate) < rate_diff) {
+ goodrate = hsu_rate;
+ rate_diff = abs(comprate - rate);
+ }
+
+ hsu_rate++;
+ }
+ if (hsu_rate > 0xFF)
+ hsu_rate = 0xFF;
+
+ return goodrate;
+}
+
+static void __serial_uart_flush(struct uart_port *port)
+{
+ u32 tmp;
+ int cnt = 0;
+
+ while ((readl(LPC32XX_HSUART_LEVEL(port->membase)) > 0) &&
+ (cnt++ < FIFO_READ_LIMIT))
+ tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+}
+
+static void __serial_lpc32xx_rx(struct uart_port *port)
+{
+ unsigned int tmp, flag;
+ struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+
+ if (!tty) {
+ /* Discard data: no tty available */
+ while (!(readl(LPC32XX_HSUART_FIFO(port->membase)) &
+ LPC32XX_HSU_RX_EMPTY))
+ ;
+
+ return;
+ }
+
+ /* Read data from FIFO and push into terminal */
+ tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+ while (!(tmp & LPC32XX_HSU_RX_EMPTY)) {
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (tmp & LPC32XX_HSU_ERROR_DATA) {
+ /* Framing error */
+ writel(LPC32XX_HSU_FE_INT,
+ LPC32XX_HSUART_IIR(port->membase));
+ port->icount.frame++;
+ flag = TTY_FRAME;
+ tty_insert_flip_char(tty, 0, TTY_FRAME);
+ }
+
+ tty_insert_flip_char(tty, (tmp & 0xFF), flag);
+
+ tmp = readl(LPC32XX_HSUART_FIFO(port->membase));
+ }
+ tty_flip_buffer_push(tty);
+ tty_kref_put(tty);
+}
+
+static void __serial_lpc32xx_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+ unsigned int tmp;
+
+ if (port->x_char) {
+ writel((u32)port->x_char, LPC32XX_HSUART_FIFO(port->membase));
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+ goto exit_tx;
+
+ /* Transfer data */
+ while (LPC32XX_HSU_TX_LEV(readl(
+ LPC32XX_HSUART_LEVEL(port->membase))) < 64) {
+ writel((u32) xmit->buf[xmit->tail],
+ LPC32XX_HSUART_FIFO(port->membase));
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+exit_tx:
+ if (uart_circ_empty(xmit)) {
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ tmp &= ~LPC32XX_HSU_TX_INT_EN;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+ }
+}
+
+static irqreturn_t serial_lpc32xx_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port = dev_id;
+ struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+ u32 status;
+
+ spin_lock(&port->lock);
+
+ /* Read UART status and clear latched interrupts */
+ status = readl(LPC32XX_HSUART_IIR(port->membase));
+
+ if (status & LPC32XX_HSU_BRK_INT) {
+ /* Break received */
+ writel(LPC32XX_HSU_BRK_INT, LPC32XX_HSUART_IIR(port->membase));
+ port->icount.brk++;
+ uart_handle_break(port);
+ }
+
+ /* Framing error */
+ if (status & LPC32XX_HSU_FE_INT)
+ writel(LPC32XX_HSU_FE_INT, LPC32XX_HSUART_IIR(port->membase));
+
+ if (status & LPC32XX_HSU_RX_OE_INT) {
+ /* Receive FIFO overrun */
+ writel(LPC32XX_HSU_RX_OE_INT,
+ LPC32XX_HSUART_IIR(port->membase));
+ port->icount.overrun++;
+ if (tty) {
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ tty_schedule_flip(tty);
+ }
+ }
+
+ /* Data received? */
+ if (status & (LPC32XX_HSU_RX_TIMEOUT_INT | LPC32XX_HSU_RX_TRIG_INT)) {
+ __serial_lpc32xx_rx(port);
+ if (tty)
+ tty_flip_buffer_push(tty);
+ }
+
+ /* Transmit data request? */
+ if ((status & LPC32XX_HSU_TX_INT) && (!uart_tx_stopped(port))) {
+ writel(LPC32XX_HSU_TX_INT, LPC32XX_HSUART_IIR(port->membase));
+ __serial_lpc32xx_tx(port);
+ }
+
+ spin_unlock(&port->lock);
+ tty_kref_put(tty);
+
+ return IRQ_HANDLED;
+}
+
+/* port->lock is not held. */
+static unsigned int serial_lpc32xx_tx_empty(struct uart_port *port)
+{
+ unsigned int ret = 0;
+
+ if (LPC32XX_HSU_TX_LEV(readl(LPC32XX_HSUART_LEVEL(port->membase))) == 0)
+ ret = TIOCSER_TEMT;
+
+ return ret;
+}
+
+/* port->lock held by caller. */
+static void serial_lpc32xx_set_mctrl(struct uart_port *port,
+ unsigned int mctrl)
+{
+ /* No signals are supported on HS UARTs */
+}
+
+/* port->lock is held by caller and interrupts are disabled. */
+static unsigned int serial_lpc32xx_get_mctrl(struct uart_port *port)
+{
+ /* No signals are supported on HS UARTs */
+ return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+}
+
+/* port->lock held by caller. */
+static void serial_lpc32xx_stop_tx(struct uart_port *port)
+{
+ u32 tmp;
+
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ tmp &= ~LPC32XX_HSU_TX_INT_EN;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+}
+
+/* port->lock held by caller. */
+static void serial_lpc32xx_start_tx(struct uart_port *port)
+{
+ u32 tmp;
+
+ __serial_lpc32xx_tx(port);
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ tmp |= LPC32XX_HSU_TX_INT_EN;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+}
+
+/* port->lock held by caller. */
+static void serial_lpc32xx_stop_rx(struct uart_port *port)
+{
+ u32 tmp;
+
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN);
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+ writel((LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT |
+ LPC32XX_HSU_FE_INT), LPC32XX_HSUART_IIR(port->membase));
+}
+
+/* port->lock held by caller. */
+static void serial_lpc32xx_enable_ms(struct uart_port *port)
+{
+ /* Modem status is not supported */
+}
+
+/* port->lock is not held. */
+static void serial_lpc32xx_break_ctl(struct uart_port *port,
+ int break_state)
+{
+ unsigned long flags;
+ u32 tmp;
+
+ spin_lock_irqsave(&port->lock, flags);
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ if (break_state != 0)
+ tmp |= LPC32XX_HSU_BREAK;
+ else
+ tmp &= ~LPC32XX_HSU_BREAK;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* LPC3250 Errata HSUART.1: Hang workaround via loopback mode on inactivity */
+static void lpc32xx_loopback_set(resource_size_t mapbase, int state)
+{
+ int bit;
+ u32 tmp;
+
+ switch (mapbase) {
+ case LPC32XX_HS_UART1_BASE:
+ bit = 0;
+ break;
+ case LPC32XX_HS_UART2_BASE:
+ bit = 1;
+ break;
+ case LPC32XX_HS_UART7_BASE:
+ bit = 6;
+ break;
+ default:
+ WARN(1, "lpc32xx_hs: Warning: Unknown port at %08x\n", mapbase);
+ return;
+ }
+
+ tmp = readl(LPC32XX_UARTCTL_CLOOP);
+ if (state)
+ tmp |= (1 << bit);
+ else
+ tmp &= ~(1 << bit);
+ writel(tmp, LPC32XX_UARTCTL_CLOOP);
+}
+
+/* port->lock is not held. */
+static int serial_lpc32xx_startup(struct uart_port *port)
+{
+ int retval;
+ unsigned long flags;
+ u32 tmp;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ __serial_uart_flush(port);
+
+ writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT |
+ LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT),
+ LPC32XX_HSUART_IIR(port->membase));
+
+ writel(0xFF, LPC32XX_HSUART_RATE(port->membase));
+
+ /*
+ * Set receiver timeout, HSU offset of 20, no break, no interrupts,
+ * and default FIFO trigger levels
+ */
+ tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+ LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+ lpc32xx_loopback_set(port->mapbase, 0); /* get out of loopback mode */
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ retval = request_irq(port->irq, serial_lpc32xx_interrupt,
+ 0, MODNAME, port);
+ if (!retval)
+ writel((tmp | LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN),
+ LPC32XX_HSUART_CTRL(port->membase));
+
+ return retval;
+}
+
+/* port->lock is not held. */
+static void serial_lpc32xx_shutdown(struct uart_port *port)
+{
+ u32 tmp;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ tmp = LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+ LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+ lpc32xx_loopback_set(port->mapbase, 1); /* go to loopback mode */
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ free_irq(port->irq, port);
+}
+
+/* port->lock is not held. */
+static void serial_lpc32xx_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned long flags;
+ unsigned int baud, quot;
+ u32 tmp;
+
+ /* Always 8-bit, no parity, 1 stop bit */
+ termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD);
+ termios->c_cflag |= CS8;
+
+ termios->c_cflag &= ~(HUPCL | CMSPAR | CLOCAL | CRTSCTS);
+
+ baud = uart_get_baud_rate(port, termios, old, 0,
+ port->uartclk / 14);
+
+ quot = __serial_get_clock_div(port->uartclk, baud);
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /* Ignore characters? */
+ tmp = readl(LPC32XX_HSUART_CTRL(port->membase));
+ if ((termios->c_cflag & CREAD) == 0)
+ tmp &= ~(LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN);
+ else
+ tmp |= LPC32XX_HSU_RX_INT_EN | LPC32XX_HSU_ERR_INT_EN;
+ writel(tmp, LPC32XX_HSUART_CTRL(port->membase));
+
+ writel(quot, LPC32XX_HSUART_RATE(port->membase));
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ /* Don't rewrite B0 */
+ if (tty_termios_baud_rate(termios))
+ tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static const char *serial_lpc32xx_type(struct uart_port *port)
+{
+ return MODNAME;
+}
+
+static void serial_lpc32xx_release_port(struct uart_port *port)
+{
+ if ((port->iotype == UPIO_MEM32) && (port->mapbase)) {
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
+
+ release_mem_region(port->mapbase, SZ_4K);
+ }
+}
+
+static int serial_lpc32xx_request_port(struct uart_port *port)
+{
+ int ret = -ENODEV;
+
+ if ((port->iotype == UPIO_MEM32) && (port->mapbase)) {
+ ret = 0;
+
+ if (!request_mem_region(port->mapbase, SZ_4K, MODNAME))
+ ret = -EBUSY;
+ else if (port->flags & UPF_IOREMAP) {
+ port->membase = ioremap(port->mapbase, SZ_4K);
+ if (!port->membase) {
+ release_mem_region(port->mapbase, SZ_4K);
+ ret = -ENOMEM;
+ }
+ }
+ }
+
+ return ret;
+}
+
+static void serial_lpc32xx_config_port(struct uart_port *port, int uflags)
+{
+ int ret;
+
+ ret = serial_lpc32xx_request_port(port);
+ if (ret < 0)
+ return;
+ port->type = PORT_UART00;
+ port->fifosize = 64;
+
+ __serial_uart_flush(port);
+
+ writel((LPC32XX_HSU_TX_INT | LPC32XX_HSU_FE_INT |
+ LPC32XX_HSU_BRK_INT | LPC32XX_HSU_RX_OE_INT),
+ LPC32XX_HSUART_IIR(port->membase));
+
+ writel(0xFF, LPC32XX_HSUART_RATE(port->membase));
+
+ /* Set receiver timeout, HSU offset of 20, no break, no interrupts,
+ and default FIFO trigger levels */
+ writel(LPC32XX_HSU_TX_TL8B | LPC32XX_HSU_RX_TL32B |
+ LPC32XX_HSU_OFFSET(20) | LPC32XX_HSU_TMO_INACT_4B,
+ LPC32XX_HSUART_CTRL(port->membase));
+}
+
+static int serial_lpc32xx_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ int ret = 0;
+
+ if (ser->type != PORT_UART00)
+ ret = -EINVAL;
+
+ return ret;
+}
+
+static struct uart_ops serial_lpc32xx_pops = {
+ .tx_empty = serial_lpc32xx_tx_empty,
+ .set_mctrl = serial_lpc32xx_set_mctrl,
+ .get_mctrl = serial_lpc32xx_get_mctrl,
+ .stop_tx = serial_lpc32xx_stop_tx,
+ .start_tx = serial_lpc32xx_start_tx,
+ .stop_rx = serial_lpc32xx_stop_rx,
+ .enable_ms = serial_lpc32xx_enable_ms,
+ .break_ctl = serial_lpc32xx_break_ctl,
+ .startup = serial_lpc32xx_startup,
+ .shutdown = serial_lpc32xx_shutdown,
+ .set_termios = serial_lpc32xx_set_termios,
+ .type = serial_lpc32xx_type,
+ .release_port = serial_lpc32xx_release_port,
+ .request_port = serial_lpc32xx_request_port,
+ .config_port = serial_lpc32xx_config_port,
+ .verify_port = serial_lpc32xx_verify_port,
+};
+
+/*
+ * Register a set of serial devices attached to a platform device
+ */
+static int __devinit serial_hs_lpc32xx_probe(struct platform_device *pdev)
+{
+ struct lpc32xx_hsuart_port *p = &lpc32xx_hs_ports[uarts_registered];
+ int ret = 0;
+ struct resource *res;
+
+ if (uarts_registered >= MAX_PORTS) {
+ dev_err(&pdev->dev,
+ "Error: Number of possible ports exceeded (%d)!\n",
+ uarts_registered + 1);
+ return -ENXIO;
+ }
+
+ memset(p, 0, sizeof(*p));
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev,
+ "Error getting mem resource for HS UART port %d\n",
+ uarts_registered);
+ return -ENXIO;
+ }
+ p->port.mapbase = res->start;
+ p->port.membase = NULL;
+
+ p->port.irq = platform_get_irq(pdev, 0);
+ if (p->port.irq < 0) {
+ dev_err(&pdev->dev, "Error getting irq for HS UART port %d\n",
+ uarts_registered);
+ return p->port.irq;
+ }
+
+ p->port.iotype = UPIO_MEM32;
+ p->port.uartclk = LPC32XX_MAIN_OSC_FREQ;
+ p->port.regshift = 2;
+ p->port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT | UPF_IOREMAP;
+ p->port.dev = &pdev->dev;
+ p->port.ops = &serial_lpc32xx_pops;
+ p->port.line = uarts_registered++;
+ spin_lock_init(&p->port.lock);
+
+ /* send port to loopback mode by default */
+ lpc32xx_loopback_set(p->port.mapbase, 1);
+
+ ret = uart_add_one_port(&lpc32xx_hs_reg, &p->port);
+
+ platform_set_drvdata(pdev, p);
+
+ return ret;
+}
+
+/*
+ * Remove serial ports registered against a platform device.
+ */
+static int __devexit serial_hs_lpc32xx_remove(struct platform_device *pdev)
+{
+ struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+ uart_remove_one_port(&lpc32xx_hs_reg, &p->port);
+
+ return 0;
+}
+
+
+#ifdef CONFIG_PM
+static int serial_hs_lpc32xx_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+ uart_suspend_port(&lpc32xx_hs_reg, &p->port);
+
+ return 0;
+}
+
+static int serial_hs_lpc32xx_resume(struct platform_device *pdev)
+{
+ struct lpc32xx_hsuart_port *p = platform_get_drvdata(pdev);
+
+ uart_resume_port(&lpc32xx_hs_reg, &p->port);
+
+ return 0;
+}
+#else
+#define serial_hs_lpc32xx_suspend NULL
+#define serial_hs_lpc32xx_resume NULL
+#endif
+
+static const struct of_device_id serial_hs_lpc32xx_dt_ids[] = {
+ { .compatible = "nxp,lpc3220-hsuart" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, serial_hs_lpc32xx_dt_ids);
+
+static struct platform_driver serial_hs_lpc32xx_driver = {
+ .probe = serial_hs_lpc32xx_probe,
+ .remove = __devexit_p(serial_hs_lpc32xx_remove),
+ .suspend = serial_hs_lpc32xx_suspend,
+ .resume = serial_hs_lpc32xx_resume,
+ .driver = {
+ .name = MODNAME,
+ .owner = THIS_MODULE,
+ .of_match_table = serial_hs_lpc32xx_dt_ids,
+ },
+};
+
+static int __init lpc32xx_hsuart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&lpc32xx_hs_reg);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&serial_hs_lpc32xx_driver);
+ if (ret)
+ uart_unregister_driver(&lpc32xx_hs_reg);
+
+ return ret;
+}
+
+static void __exit lpc32xx_hsuart_exit(void)
+{
+ platform_driver_unregister(&serial_hs_lpc32xx_driver);
+ uart_unregister_driver(&lpc32xx_hs_reg);
+}
+
+module_init(lpc32xx_hsuart_init);
+module_exit(lpc32xx_hsuart_exit);
+
+MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>");
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_DESCRIPTION("NXP LPC32XX High Speed UART driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c
index 34e7187..df443b9 100644
--- a/drivers/tty/serial/of_serial.c
+++ b/drivers/tty/serial/of_serial.c
@@ -105,6 +105,10 @@
port->uartclk = clk;
port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
| UPF_FIXED_PORT | UPF_FIXED_TYPE;
+
+ if (of_find_property(np, "no-loopback-test", NULL))
+ port->flags |= UPF_SKIP_TEST;
+
port->dev = &ofdev->dev;
if (type == PORT_TEGRA)
@@ -144,8 +148,15 @@
switch (port_type) {
#ifdef CONFIG_SERIAL_8250
case PORT_8250 ... PORT_MAX_8250:
- ret = serial8250_register_port(&port);
+ {
+ /* For now the of bindings don't support the extra
+ 8250 specific bits */
+ struct uart_8250_port port8250;
+ memset(&port8250, 0, sizeof(port8250));
+ port8250.port = port;
+ ret = serial8250_register_8250_port(&port8250);
break;
+ }
#endif
#ifdef CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL
case PORT_NWPSERIAL:
diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c
index 5847a4b..9033fc6 100644
--- a/drivers/tty/serial/pxa.c
+++ b/drivers/tty/serial/pxa.c
@@ -670,9 +670,19 @@
{
struct uart_pxa_port *up = serial_pxa_ports[co->index];
unsigned int ier;
+ unsigned long flags;
+ int locked = 1;
clk_prepare_enable(up->clk);
+ local_irq_save(flags);
+ if (up->port.sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock(&up->port.lock);
+ else
+ spin_lock(&up->port.lock);
+
/*
* First save the IER then disable the interrupts
*/
@@ -688,6 +698,10 @@
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
+ if (locked)
+ spin_unlock(&up->port.lock);
+ local_irq_restore(flags);
+
clk_disable_unprepare(up->clk);
}
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index 02d07bf..5c5e7e0 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -529,7 +529,7 @@
switch (level) {
case 3:
- if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+ if (!IS_ERR(ourport->baudclk))
clk_disable(ourport->baudclk);
clk_disable(ourport->clk);
@@ -538,7 +538,7 @@
case 0:
clk_enable(ourport->clk);
- if (!IS_ERR(ourport->baudclk) && ourport->baudclk != NULL)
+ if (!IS_ERR(ourport->baudclk))
clk_enable(ourport->baudclk);
break;
@@ -604,7 +604,6 @@
char clkname[MAX_CLK_NAME_LENGTH];
int calc_deviation, deviation = (1 << 30) - 1;
- *best_clk = NULL;
clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
ourport->info->def_clk_sel;
for (cnt = 0; cnt < info->num_clks; cnt++) {
@@ -613,7 +612,7 @@
sprintf(clkname, "clk_uart_baud%d", cnt);
clk = clk_get(ourport->port.dev, clkname);
- if (IS_ERR_OR_NULL(clk))
+ if (IS_ERR(clk))
continue;
rate = clk_get_rate(clk);
@@ -684,7 +683,7 @@
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
- struct clk *clk = NULL;
+ struct clk *clk = ERR_PTR(-EINVAL);
unsigned long flags;
unsigned int baud, quot, clk_sel = 0;
unsigned int ulcon;
@@ -705,7 +704,7 @@
quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel);
if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
quot = port->custom_divisor;
- if (!clk)
+ if (IS_ERR(clk))
return;
/* check to see if we need to change clock source */
@@ -713,9 +712,9 @@
if (ourport->baudclk != clk) {
s3c24xx_serial_setsource(port, clk_sel);
- if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
+ if (!IS_ERR(ourport->baudclk)) {
clk_disable(ourport->baudclk);
- ourport->baudclk = NULL;
+ ourport->baudclk = ERR_PTR(-EINVAL);
}
clk_enable(clk);
@@ -1036,7 +1035,7 @@
if (tty == NULL)
goto exit;
- termios = tty->termios;
+ termios = &tty->termios;
if (termios == NULL) {
printk(KERN_WARNING "%s: no termios?\n", __func__);
@@ -1160,7 +1159,11 @@
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
- return snprintf(buf, PAGE_SIZE, "* %s\n", ourport->baudclk->name);
+ if (IS_ERR(ourport->baudclk))
+ return -EINVAL;
+
+ return snprintf(buf, PAGE_SIZE, "* %s\n",
+ ourport->baudclk->name ?: "(null)");
}
static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
@@ -1200,6 +1203,7 @@
return -ENODEV;
}
+ ourport->baudclk = ERR_PTR(-EINVAL);
ourport->info = ourport->drv_data->info;
ourport->cfg = (pdev->dev.platform_data) ?
(struct s3c2410_uartcfg *)pdev->dev.platform_data :
@@ -1387,7 +1391,7 @@
sprintf(clk_name, "clk_uart_baud%d", clk_sel);
clk = clk_get(port->dev, clk_name);
- if (!IS_ERR(clk) && clk != NULL)
+ if (!IS_ERR(clk))
rate = clk_get_rate(clk);
else
rate = 1;
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index a21dc8e..d98b1bd 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -159,7 +159,7 @@
retval = uport->ops->startup(uport);
if (retval == 0) {
if (uart_console(uport) && uport->cons->cflag) {
- tty->termios->c_cflag = uport->cons->cflag;
+ tty->termios.c_cflag = uport->cons->cflag;
uport->cons->cflag = 0;
}
/*
@@ -172,7 +172,7 @@
* Setup the RTS and DTR signals once the
* port is open and ready to respond.
*/
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
}
@@ -240,7 +240,7 @@
/*
* Turn off DTR and RTS early.
*/
- if (!tty || (tty->termios->c_cflag & HUPCL))
+ if (!tty || (tty->termios.c_cflag & HUPCL))
uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
uart_port_shutdown(port);
@@ -440,10 +440,10 @@
* If we have no tty, termios, or the port does not exist,
* then we can't set the parameters for this port.
*/
- if (!tty || !tty->termios || uport->type == PORT_UNKNOWN)
+ if (!tty || uport->type == PORT_UNKNOWN)
return;
- termios = tty->termios;
+ termios = &tty->termios;
/*
* Set flags based on termios cflag
@@ -614,7 +614,7 @@
if (I_IXOFF(tty))
uart_send_xchar(tty, STOP_CHAR(tty));
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
uart_clear_mctrl(state->uart_port, TIOCM_RTS);
}
@@ -630,7 +630,7 @@
uart_send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS)
+ if (tty->termios.c_cflag & CRTSCTS)
uart_set_mctrl(port, TIOCM_RTS);
}
@@ -1187,7 +1187,7 @@
struct uart_port *uport = state->uart_port;
if (uport->ops->set_ldisc)
- uport->ops->set_ldisc(uport, tty->termios->c_line);
+ uport->ops->set_ldisc(uport, tty->termios.c_line);
}
static void uart_set_termios(struct tty_struct *tty,
@@ -1195,7 +1195,7 @@
{
struct uart_state *state = tty->driver_data;
unsigned long flags;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
/*
@@ -1206,9 +1206,9 @@
*/
#define RELEVANT_IFLAG(iflag) ((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
if ((cflag ^ old_termios->c_cflag) == 0 &&
- tty->termios->c_ospeed == old_termios->c_ospeed &&
- tty->termios->c_ispeed == old_termios->c_ispeed &&
- RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) {
+ tty->termios.c_ospeed == old_termios->c_ospeed &&
+ tty->termios.c_ispeed == old_termios->c_ispeed &&
+ RELEVANT_IFLAG(tty->termios.c_iflag ^ old_termios->c_iflag) == 0) {
return;
}
@@ -1960,8 +1960,8 @@
/*
* If that's unset, use the tty termios setting.
*/
- if (port->tty && port->tty->termios && termios.c_cflag == 0)
- termios = *(port->tty->termios);
+ if (port->tty && termios.c_cflag == 0)
+ termios = port->tty->termios;
if (console_suspend_enabled)
uart_change_pm(state, 0);
diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c
index 593d40a..bdeeb31 100644
--- a/drivers/tty/synclink.c
+++ b/drivers/tty/synclink.c
@@ -1840,22 +1840,22 @@
usc_DisableInterrupts(info,RECEIVE_DATA + RECEIVE_STATUS +
TRANSMIT_DATA + TRANSMIT_STATUS + IO_PIN + MISC );
usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE);
-
+
/* Disable DMAEN (Port 7, Bit 14) */
/* This disconnects the DMA request signal from the ISA bus */
/* on the ISA adapter. This has no effect for the PCI adapter */
usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14));
-
+
/* Disable INTEN (Port 6, Bit12) */
/* This disconnects the IRQ request signal to the ISA bus */
/* on the ISA adapter. This has no effect for the PCI adapter */
usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12));
-
- if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+
+ if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
usc_set_serial_signals(info);
}
-
+
spin_unlock_irqrestore(&info->irq_spinlock,flags);
mgsl_release_resources(info);
@@ -1895,7 +1895,7 @@
usc_EnableInterrupts(info, IO_PIN);
usc_get_serial_signals(info);
- if (info->netcount || info->port.tty->termios->c_cflag & CREAD)
+ if (info->netcount || info->port.tty->termios.c_cflag & CREAD)
usc_start_receiver(info);
spin_unlock_irqrestore(&info->irq_spinlock,flags);
@@ -1908,14 +1908,14 @@
unsigned cflag;
int bits_per_char;
- if (!info->port.tty || !info->port.tty->termios)
+ if (!info->port.tty)
return;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):mgsl_change_params(%s)\n",
__FILE__,__LINE__, info->device_name );
- cflag = info->port.tty->termios->c_cflag;
+ cflag = info->port.tty->termios.c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
@@ -2367,8 +2367,8 @@
if (I_IXOFF(tty))
mgsl_send_xchar(tty, STOP_CHAR(tty));
-
- if (tty->termios->c_cflag & CRTSCTS) {
+
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->irq_spinlock,flags);
info->serial_signals &= ~SerialSignal_RTS;
usc_set_serial_signals(info);
@@ -2401,8 +2401,8 @@
else
mgsl_send_xchar(tty, START_CHAR(tty));
}
-
- if (tty->termios->c_cflag & CRTSCTS) {
+
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->irq_spinlock,flags);
info->serial_signals |= SerialSignal_RTS;
usc_set_serial_signals(info);
@@ -3045,7 +3045,7 @@
/* Handle transition to B0 status */
if (old_termios->c_cflag & CBAUD &&
- !(tty->termios->c_cflag & CBAUD)) {
+ !(tty->termios.c_cflag & CBAUD)) {
info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
spin_lock_irqsave(&info->irq_spinlock,flags);
usc_set_serial_signals(info);
@@ -3054,9 +3054,9 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
- tty->termios->c_cflag & CBAUD) {
+ tty->termios.c_cflag & CBAUD) {
info->serial_signals |= SerialSignal_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
info->serial_signals |= SerialSignal_RTS;
}
@@ -3067,7 +3067,7 @@
/* Handle turning off CRTSCTS */
if (old_termios->c_cflag & CRTSCTS &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
mgsl_start(tty);
}
@@ -3287,7 +3287,7 @@
return 0;
}
- if (tty->termios->c_cflag & CLOCAL)
+ if (tty->termios.c_cflag & CLOCAL)
do_clocal = true;
/* Wait for carrier detect and the line to become
@@ -3313,7 +3313,7 @@
port->blocked_open++;
while (1) {
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
diff --git a/drivers/tty/synclink_gt.c b/drivers/tty/synclink_gt.c
index aa1debf..f02d18a 100644
--- a/drivers/tty/synclink_gt.c
+++ b/drivers/tty/synclink_gt.c
@@ -785,7 +785,7 @@
/* Handle transition to B0 status */
if (old_termios->c_cflag & CBAUD &&
- !(tty->termios->c_cflag & CBAUD)) {
+ !(tty->termios.c_cflag & CBAUD)) {
info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
spin_lock_irqsave(&info->lock,flags);
set_signals(info);
@@ -794,9 +794,9 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
- tty->termios->c_cflag & CBAUD) {
+ tty->termios.c_cflag & CBAUD) {
info->signals |= SerialSignal_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
info->signals |= SerialSignal_RTS;
}
@@ -807,7 +807,7 @@
/* Handle turning off CRTSCTS */
if (old_termios->c_cflag & CRTSCTS &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
tx_release(tty);
}
@@ -1372,7 +1372,7 @@
DBGINFO(("%s throttle\n", info->device_name));
if (I_IXOFF(tty))
send_xchar(tty, STOP_CHAR(tty));
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->signals &= ~SerialSignal_RTS;
set_signals(info);
@@ -1397,7 +1397,7 @@
else
send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->signals |= SerialSignal_RTS;
set_signals(info);
@@ -2493,7 +2493,7 @@
slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
- if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+ if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
set_signals(info);
}
@@ -2534,7 +2534,7 @@
get_signals(info);
if (info->netcount ||
- (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
+ (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
rx_start(info);
spin_unlock_irqrestore(&info->lock,flags);
@@ -2548,11 +2548,11 @@
unsigned cflag;
int bits_per_char;
- if (!info->port.tty || !info->port.tty->termios)
+ if (!info->port.tty)
return;
DBGINFO(("%s change_params\n", info->device_name));
- cflag = info->port.tty->termios->c_cflag;
+ cflag = info->port.tty->termios.c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
@@ -3292,7 +3292,7 @@
return 0;
}
- if (tty->termios->c_cflag & CLOCAL)
+ if (tty->termios.c_cflag & CLOCAL)
do_clocal = true;
/* Wait for carrier detect and the line to become
@@ -3314,7 +3314,7 @@
port->blocked_open++;
while (1) {
- if ((tty->termios->c_cflag & CBAUD))
+ if ((tty->termios.c_cflag & CBAUD))
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
diff --git a/drivers/tty/synclinkmp.c b/drivers/tty/synclinkmp.c
index a3dddc1..ae75a3c 100644
--- a/drivers/tty/synclinkmp.c
+++ b/drivers/tty/synclinkmp.c
@@ -873,7 +873,7 @@
/* Handle transition to B0 status */
if (old_termios->c_cflag & CBAUD &&
- !(tty->termios->c_cflag & CBAUD)) {
+ !(tty->termios.c_cflag & CBAUD)) {
info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
spin_lock_irqsave(&info->lock,flags);
set_signals(info);
@@ -882,9 +882,9 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) &&
- tty->termios->c_cflag & CBAUD) {
+ tty->termios.c_cflag & CBAUD) {
info->serial_signals |= SerialSignal_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
info->serial_signals |= SerialSignal_RTS;
}
@@ -895,7 +895,7 @@
/* Handle turning off CRTSCTS */
if (old_termios->c_cflag & CRTSCTS &&
- !(tty->termios->c_cflag & CRTSCTS)) {
+ !(tty->termios.c_cflag & CRTSCTS)) {
tty->hw_stopped = 0;
tx_release(tty);
}
@@ -1473,7 +1473,7 @@
if (I_IXOFF(tty))
send_xchar(tty, STOP_CHAR(tty));
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->serial_signals &= ~SerialSignal_RTS;
set_signals(info);
@@ -1502,7 +1502,7 @@
send_xchar(tty, START_CHAR(tty));
}
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
spin_lock_irqsave(&info->lock,flags);
info->serial_signals |= SerialSignal_RTS;
set_signals(info);
@@ -2708,7 +2708,7 @@
reset_port(info);
- if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
+ if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
set_signals(info);
}
@@ -2749,7 +2749,7 @@
get_signals(info);
- if (info->netcount || (info->port.tty && info->port.tty->termios->c_cflag & CREAD) )
+ if (info->netcount || (info->port.tty && info->port.tty->termios.c_cflag & CREAD) )
rx_start(info);
spin_unlock_irqrestore(&info->lock,flags);
@@ -2762,14 +2762,14 @@
unsigned cflag;
int bits_per_char;
- if (!info->port.tty || !info->port.tty->termios)
+ if (!info->port.tty)
return;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s change_params()\n",
__FILE__,__LINE__, info->device_name );
- cflag = info->port.tty->termios->c_cflag;
+ cflag = info->port.tty->termios.c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
@@ -3306,7 +3306,7 @@
return 0;
}
- if (tty->termios->c_cflag & CLOCAL)
+ if (tty->termios.c_cflag & CLOCAL)
do_clocal = true;
/* Wait for carrier detect and the line to become
@@ -3332,7 +3332,7 @@
port->blocked_open++;
while (1) {
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index b425c79..c6f4d71 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -1249,21 +1249,19 @@
struct ktermios *tp;
int idx = tty->index;
- tp = tty->driver->termios[idx];
- if (tp == NULL) {
- tp = kzalloc(sizeof(struct ktermios[2]), GFP_KERNEL);
- if (tp == NULL)
- return -ENOMEM;
- memcpy(tp, &tty->driver->init_termios,
- sizeof(struct ktermios));
- tty->driver->termios[idx] = tp;
+ if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS)
+ tty->termios = tty->driver->init_termios;
+ else {
+ /* Check for lazy saved data */
+ tp = tty->driver->termios[idx];
+ if (tp != NULL)
+ tty->termios = *tp;
+ else
+ tty->termios = tty->driver->init_termios;
}
- tty->termios = tp;
- tty->termios_locked = tp + 1;
-
/* Compatibility until drivers always set this */
- tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios);
- tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios);
+ tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios);
+ tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios);
return 0;
}
EXPORT_SYMBOL_GPL(tty_init_termios);
@@ -1407,6 +1405,9 @@
if (retval < 0)
goto err_deinit_tty;
+ if (!tty->port)
+ tty->port = driver->ports[idx];
+
/*
* Structures all installed ... call the ldisc open routines.
* If we fail here just call release_tty to clean up. No need
@@ -1436,22 +1437,24 @@
{
struct ktermios *tp;
int idx = tty->index;
- /* Kill this flag and push into drivers for locking etc */
- if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) {
- /* FIXME: Locking on ->termios array */
- tp = tty->termios;
- tty->driver->termios[idx] = NULL;
- kfree(tp);
+
+ /* If the port is going to reset then it has no termios to save */
+ if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS)
+ return;
+
+ /* Stash the termios data */
+ tp = tty->driver->termios[idx];
+ if (tp == NULL) {
+ tp = kmalloc(sizeof(struct ktermios), GFP_KERNEL);
+ if (tp == NULL) {
+ pr_warn("tty: no memory to save termios state.\n");
+ return;
+ }
}
+ *tp = tty->termios;
}
EXPORT_SYMBOL(tty_free_termios);
-void tty_shutdown(struct tty_struct *tty)
-{
- tty_driver_remove_tty(tty->driver, tty);
- tty_free_termios(tty);
-}
-EXPORT_SYMBOL(tty_shutdown);
/**
* release_one_tty - release tty structure memory
@@ -1462,7 +1465,6 @@
* in use. It also gets called when setup of a device fails.
*
* Locking:
- * tty_mutex - sometimes only
* takes the file list lock internally when working on the list
* of ttys that the driver keeps.
*
@@ -1495,11 +1497,6 @@
{
struct tty_struct *tty = container_of(kref, struct tty_struct, kref);
- if (tty->ops->shutdown)
- tty->ops->shutdown(tty);
- else
- tty_shutdown(tty);
-
/* The hangup queue is now free so we can reuse it rather than
waste a chunk of memory for each port */
INIT_WORK(&tty->hangup_work, release_one_tty);
@@ -1528,16 +1525,20 @@
* and decrement the refcount of the backing module.
*
* Locking:
- * tty_mutex - sometimes only
+ * tty_mutex
* takes the file list lock internally when working on the list
* of ttys that the driver keeps.
- * FIXME: should we require tty_mutex is held here ??
*
*/
static void release_tty(struct tty_struct *tty, int idx)
{
/* This should always be true but check for the moment */
WARN_ON(tty->index != idx);
+ WARN_ON(!mutex_is_locked(&tty_mutex));
+ if (tty->ops->shutdown)
+ tty->ops->shutdown(tty);
+ tty_free_termios(tty);
+ tty_driver_remove_tty(tty->driver, tty);
if (tty->link)
tty_kref_put(tty->link);
@@ -1572,22 +1573,12 @@
__func__, idx, tty->name);
return -1;
}
- if (tty->termios != tty->driver->termios[idx]) {
- printk(KERN_DEBUG "%s: driver.termios[%d] not termios for (%s)\n",
- __func__, idx, tty->name);
- return -1;
- }
if (tty->driver->other) {
if (o_tty != tty->driver->other->ttys[idx]) {
printk(KERN_DEBUG "%s: other->table[%d] not o_tty for (%s)\n",
__func__, idx, tty->name);
return -1;
}
- if (o_tty->termios != tty->driver->other->termios[idx]) {
- printk(KERN_DEBUG "%s: other->termios[%d] not o_termios for (%s)\n",
- __func__, idx, tty->name);
- return -1;
- }
if (o_tty->link != tty) {
printk(KERN_DEBUG "%s: bad pty pointers\n", __func__);
return -1;
@@ -1715,6 +1706,9 @@
* The closing flags are now consistent with the open counts on
* both sides, and we've completed the last operation that could
* block, so it's safe to proceed with closing.
+ *
+ * We must *not* drop the tty_mutex until we ensure that a further
+ * entry into tty_open can not pick up this tty.
*/
if (pty_master) {
if (--o_tty->count < 0) {
@@ -1766,12 +1760,13 @@
}
mutex_unlock(&tty_mutex);
+ tty_unlock();
+ /* At this point the TTY_CLOSING flag should ensure a dead tty
+ cannot be re-opened by a racing opener */
/* check whether both sides are closing ... */
- if (!tty_closing || (o_tty && !o_tty_closing)) {
- tty_unlock();
+ if (!tty_closing || (o_tty && !o_tty_closing))
return 0;
- }
#ifdef TTY_DEBUG_HANGUP
printk(KERN_DEBUG "%s: freeing tty structure...\n", __func__);
@@ -1784,12 +1779,14 @@
* The release_tty function takes care of the details of clearing
* the slots and preserving the termios structure.
*/
+ mutex_lock(&tty_mutex);
release_tty(tty, idx);
+ mutex_unlock(&tty_mutex);
/* Make this pty number available for reallocation */
if (devpts)
devpts_kill_index(inode, idx);
- tty_unlock();
+
return 0;
}
@@ -3094,6 +3091,7 @@
kfree(p);
cdev_del(&driver->cdev);
}
+ kfree(driver->ports);
kfree(driver);
}
@@ -3132,6 +3130,18 @@
if (!p)
return -ENOMEM;
}
+ /*
+ * There is too many lines in PTY and we won't need the array there
+ * since it has an ->install hook where it assigns ports properly.
+ */
+ if (driver->type != TTY_DRIVER_TYPE_PTY) {
+ driver->ports = kcalloc(driver->num, sizeof(struct tty_port *),
+ GFP_KERNEL);
+ if (!driver->ports) {
+ error = -ENOMEM;
+ goto err_free_p;
+ }
+ }
if (!driver->major) {
error = alloc_chrdev_region(&dev, driver->minor_start,
@@ -3144,10 +3154,8 @@
dev = MKDEV(driver->major, driver->minor_start);
error = register_chrdev_region(dev, driver->num, driver->name);
}
- if (error < 0) {
- kfree(p);
- return error;
- }
+ if (error < 0)
+ goto err_free_p;
if (p) {
driver->ttys = (struct tty_struct **)p;
@@ -3160,13 +3168,8 @@
cdev_init(&driver->cdev, &tty_fops);
driver->cdev.owner = driver->owner;
error = cdev_add(&driver->cdev, dev, driver->num);
- if (error) {
- unregister_chrdev_region(dev, driver->num);
- driver->ttys = NULL;
- driver->termios = NULL;
- kfree(p);
- return error;
- }
+ if (error)
+ goto err_unreg_char;
mutex_lock(&tty_mutex);
list_add(&driver->tty_drivers, &tty_drivers);
@@ -3193,13 +3196,14 @@
list_del(&driver->tty_drivers);
mutex_unlock(&tty_mutex);
+err_unreg_char:
unregister_chrdev_region(dev, driver->num);
driver->ttys = NULL;
driver->termios = NULL;
+err_free_p: /* destruct_tty_driver will free driver->ports */
kfree(p);
return error;
}
-
EXPORT_SYMBOL(tty_register_driver);
/*
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index a1b9a2f..12b1fa0 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -410,7 +410,7 @@
void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud)
{
- tty_termios_encode_baud_rate(tty->termios, ibaud, obaud);
+ tty_termios_encode_baud_rate(&tty->termios, ibaud, obaud);
}
EXPORT_SYMBOL_GPL(tty_encode_baud_rate);
@@ -427,7 +427,7 @@
speed_t tty_get_baud_rate(struct tty_struct *tty)
{
- speed_t baud = tty_termios_baud_rate(tty->termios);
+ speed_t baud = tty_termios_baud_rate(&tty->termios);
if (baud == 38400 && tty->alt_speed) {
if (!tty->warned) {
@@ -509,14 +509,14 @@
/* FIXME: we need to decide on some locking/ordering semantics
for the set_termios notification eventually */
mutex_lock(&tty->termios_mutex);
- old_termios = *tty->termios;
- *tty->termios = *new_termios;
- unset_locked_termios(tty->termios, &old_termios, tty->termios_locked);
+ old_termios = tty->termios;
+ tty->termios = *new_termios;
+ unset_locked_termios(&tty->termios, &old_termios, &tty->termios_locked);
/* See if packet mode change of state. */
if (tty->link && tty->link->packet) {
int extproc = (old_termios.c_lflag & EXTPROC) |
- (tty->termios->c_lflag & EXTPROC);
+ (tty->termios.c_lflag & EXTPROC);
int old_flow = ((old_termios.c_iflag & IXON) &&
(old_termios.c_cc[VSTOP] == '\023') &&
(old_termios.c_cc[VSTART] == '\021'));
@@ -542,7 +542,7 @@
if (tty->ops->set_termios)
(*tty->ops->set_termios)(tty, &old_termios);
else
- tty_termios_copy_hw(tty->termios, &old_termios);
+ tty_termios_copy_hw(&tty->termios, &old_termios);
ld = tty_ldisc_ref(tty);
if (ld != NULL) {
@@ -578,7 +578,7 @@
return retval;
mutex_lock(&tty->termios_mutex);
- memcpy(&tmp_termios, tty->termios, sizeof(struct ktermios));
+ tmp_termios = tty->termios;
mutex_unlock(&tty->termios_mutex);
if (opt & TERMIOS_TERMIO) {
@@ -632,14 +632,14 @@
static void copy_termios(struct tty_struct *tty, struct ktermios *kterm)
{
mutex_lock(&tty->termios_mutex);
- memcpy(kterm, tty->termios, sizeof(struct ktermios));
+ *kterm = tty->termios;
mutex_unlock(&tty->termios_mutex);
}
static void copy_termios_locked(struct tty_struct *tty, struct ktermios *kterm)
{
mutex_lock(&tty->termios_mutex);
- memcpy(kterm, tty->termios_locked, sizeof(struct ktermios));
+ *kterm = tty->termios_locked;
mutex_unlock(&tty->termios_mutex);
}
@@ -707,16 +707,16 @@
{
int flags = 0;
- if (!(tty->termios->c_lflag & ICANON)) {
- if (tty->termios->c_lflag & ISIG)
+ if (!(tty->termios.c_lflag & ICANON)) {
+ if (tty->termios.c_lflag & ISIG)
flags |= 0x02; /* cbreak */
else
flags |= 0x20; /* raw */
}
- if (tty->termios->c_lflag & ECHO)
+ if (tty->termios.c_lflag & ECHO)
flags |= 0x08; /* echo */
- if (tty->termios->c_oflag & OPOST)
- if (tty->termios->c_oflag & ONLCR)
+ if (tty->termios.c_oflag & OPOST)
+ if (tty->termios.c_oflag & ONLCR)
flags |= 0x10; /* crmod */
return flags;
}
@@ -726,10 +726,10 @@
struct sgttyb tmp;
mutex_lock(&tty->termios_mutex);
- tmp.sg_ispeed = tty->termios->c_ispeed;
- tmp.sg_ospeed = tty->termios->c_ospeed;
- tmp.sg_erase = tty->termios->c_cc[VERASE];
- tmp.sg_kill = tty->termios->c_cc[VKILL];
+ tmp.sg_ispeed = tty->termios.c_ispeed;
+ tmp.sg_ospeed = tty->termios.c_ospeed;
+ tmp.sg_erase = tty->termios.c_cc[VERASE];
+ tmp.sg_kill = tty->termios.c_cc[VKILL];
tmp.sg_flags = get_sgflags(tty);
mutex_unlock(&tty->termios_mutex);
@@ -787,7 +787,7 @@
return -EFAULT;
mutex_lock(&tty->termios_mutex);
- termios = *tty->termios;
+ termios = tty->termios;
termios.c_cc[VERASE] = tmp.sg_erase;
termios.c_cc[VKILL] = tmp.sg_kill;
set_sgflags(&termios, tmp.sg_flags);
@@ -808,12 +808,12 @@
struct tchars tmp;
mutex_lock(&tty->termios_mutex);
- tmp.t_intrc = tty->termios->c_cc[VINTR];
- tmp.t_quitc = tty->termios->c_cc[VQUIT];
- tmp.t_startc = tty->termios->c_cc[VSTART];
- tmp.t_stopc = tty->termios->c_cc[VSTOP];
- tmp.t_eofc = tty->termios->c_cc[VEOF];
- tmp.t_brkc = tty->termios->c_cc[VEOL2]; /* what is brkc anyway? */
+ tmp.t_intrc = tty->termios.c_cc[VINTR];
+ tmp.t_quitc = tty->termios.c_cc[VQUIT];
+ tmp.t_startc = tty->termios.c_cc[VSTART];
+ tmp.t_stopc = tty->termios.c_cc[VSTOP];
+ tmp.t_eofc = tty->termios.c_cc[VEOF];
+ tmp.t_brkc = tty->termios.c_cc[VEOL2]; /* what is brkc anyway? */
mutex_unlock(&tty->termios_mutex);
return copy_to_user(tchars, &tmp, sizeof(tmp)) ? -EFAULT : 0;
}
@@ -825,12 +825,12 @@
if (copy_from_user(&tmp, tchars, sizeof(tmp)))
return -EFAULT;
mutex_lock(&tty->termios_mutex);
- tty->termios->c_cc[VINTR] = tmp.t_intrc;
- tty->termios->c_cc[VQUIT] = tmp.t_quitc;
- tty->termios->c_cc[VSTART] = tmp.t_startc;
- tty->termios->c_cc[VSTOP] = tmp.t_stopc;
- tty->termios->c_cc[VEOF] = tmp.t_eofc;
- tty->termios->c_cc[VEOL2] = tmp.t_brkc; /* what is brkc anyway? */
+ tty->termios.c_cc[VINTR] = tmp.t_intrc;
+ tty->termios.c_cc[VQUIT] = tmp.t_quitc;
+ tty->termios.c_cc[VSTART] = tmp.t_startc;
+ tty->termios.c_cc[VSTOP] = tmp.t_stopc;
+ tty->termios.c_cc[VEOF] = tmp.t_eofc;
+ tty->termios.c_cc[VEOL2] = tmp.t_brkc; /* what is brkc anyway? */
mutex_unlock(&tty->termios_mutex);
return 0;
}
@@ -842,14 +842,14 @@
struct ltchars tmp;
mutex_lock(&tty->termios_mutex);
- tmp.t_suspc = tty->termios->c_cc[VSUSP];
+ tmp.t_suspc = tty->termios.c_cc[VSUSP];
/* what is dsuspc anyway? */
- tmp.t_dsuspc = tty->termios->c_cc[VSUSP];
- tmp.t_rprntc = tty->termios->c_cc[VREPRINT];
+ tmp.t_dsuspc = tty->termios.c_cc[VSUSP];
+ tmp.t_rprntc = tty->termios.c_cc[VREPRINT];
/* what is flushc anyway? */
- tmp.t_flushc = tty->termios->c_cc[VEOL2];
- tmp.t_werasc = tty->termios->c_cc[VWERASE];
- tmp.t_lnextc = tty->termios->c_cc[VLNEXT];
+ tmp.t_flushc = tty->termios.c_cc[VEOL2];
+ tmp.t_werasc = tty->termios.c_cc[VWERASE];
+ tmp.t_lnextc = tty->termios.c_cc[VLNEXT];
mutex_unlock(&tty->termios_mutex);
return copy_to_user(ltchars, &tmp, sizeof(tmp)) ? -EFAULT : 0;
}
@@ -862,14 +862,14 @@
return -EFAULT;
mutex_lock(&tty->termios_mutex);
- tty->termios->c_cc[VSUSP] = tmp.t_suspc;
+ tty->termios.c_cc[VSUSP] = tmp.t_suspc;
/* what is dsuspc anyway? */
- tty->termios->c_cc[VEOL2] = tmp.t_dsuspc;
- tty->termios->c_cc[VREPRINT] = tmp.t_rprntc;
+ tty->termios.c_cc[VEOL2] = tmp.t_dsuspc;
+ tty->termios.c_cc[VREPRINT] = tmp.t_rprntc;
/* what is flushc anyway? */
- tty->termios->c_cc[VEOL2] = tmp.t_flushc;
- tty->termios->c_cc[VWERASE] = tmp.t_werasc;
- tty->termios->c_cc[VLNEXT] = tmp.t_lnextc;
+ tty->termios.c_cc[VEOL2] = tmp.t_flushc;
+ tty->termios.c_cc[VWERASE] = tmp.t_werasc;
+ tty->termios.c_cc[VLNEXT] = tmp.t_lnextc;
mutex_unlock(&tty->termios_mutex);
return 0;
}
@@ -920,12 +920,12 @@
struct ktermios old;
mutex_lock(&tty->termios_mutex);
- old = *tty->termios;
- tty->termios->c_cflag &= ~CLOCAL;
- tty->termios->c_cflag |= bit;
+ old = tty->termios;
+ tty->termios.c_cflag &= ~CLOCAL;
+ tty->termios.c_cflag |= bit;
if (tty->ops->set_termios)
tty->ops->set_termios(tty, &old);
- if ((tty->termios->c_cflag & CLOCAL) != bit)
+ if ((tty->termios.c_cflag & CLOCAL) != bit)
ret = -EINVAL;
mutex_unlock(&tty->termios_mutex);
return ret;
@@ -1031,7 +1031,7 @@
(struct termios __user *) arg))
return -EFAULT;
mutex_lock(&real_tty->termios_mutex);
- memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios));
+ real_tty->termios_locked = kterm;
mutex_unlock(&real_tty->termios_mutex);
return 0;
#else
@@ -1048,7 +1048,7 @@
(struct termios __user *) arg))
return -EFAULT;
mutex_lock(&real_tty->termios_mutex);
- memcpy(real_tty->termios_locked, &kterm, sizeof(struct ktermios));
+ real_tty->termios_locked = kterm;
mutex_unlock(&real_tty->termios_mutex);
return ret;
#endif
diff --git a/drivers/tty/tty_ldisc.c b/drivers/tty/tty_ldisc.c
index 6f99c99..3d06871 100644
--- a/drivers/tty/tty_ldisc.c
+++ b/drivers/tty/tty_ldisc.c
@@ -413,7 +413,7 @@
static void tty_set_termios_ldisc(struct tty_struct *tty, int num)
{
mutex_lock(&tty->termios_mutex);
- tty->termios->c_line = num;
+ tty->termios.c_line = num;
mutex_unlock(&tty->termios_mutex);
}
@@ -722,9 +722,9 @@
static void tty_reset_termios(struct tty_struct *tty)
{
mutex_lock(&tty->termios_mutex);
- *tty->termios = tty->driver->init_termios;
- tty->termios->c_ispeed = tty_termios_input_baud_rate(tty->termios);
- tty->termios->c_ospeed = tty_termios_baud_rate(tty->termios);
+ tty->termios = tty->driver->init_termios;
+ tty->termios.c_ispeed = tty_termios_input_baud_rate(&tty->termios);
+ tty->termios.c_ospeed = tty_termios_baud_rate(&tty->termios);
mutex_unlock(&tty->termios_mutex);
}
@@ -846,7 +846,7 @@
if (reset == 0) {
- if (!tty_ldisc_reinit(tty, tty->termios->c_line))
+ if (!tty_ldisc_reinit(tty, tty->termios.c_line))
err = tty_ldisc_open(tty, tty->ldisc);
else
err = 1;
@@ -912,7 +912,6 @@
* race with the set_ldisc code path.
*/
- tty_unlock();
tty_ldisc_halt(tty);
tty_ldisc_flush_works(tty);
tty_lock();
@@ -930,6 +929,8 @@
tty_set_termios_ldisc(tty, N_TTY);
mutex_unlock(&tty->ldisc_mutex);
+ tty_unlock();
+
/* This will need doing differently if we need to lock */
if (o_tty)
tty_ldisc_release(o_tty, NULL);
diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index bf6e238..edcb827 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -33,6 +33,15 @@
}
EXPORT_SYMBOL(tty_port_init);
+struct device *tty_port_register_device(struct tty_port *port,
+ struct tty_driver *driver, unsigned index,
+ struct device *device)
+{
+ driver->ports[index] = port;
+ return tty_register_device(driver, index, device);
+}
+EXPORT_SYMBOL_GPL(tty_port_register_device);
+
int tty_port_alloc_xmit_buf(struct tty_port *port)
{
/* We may sleep in get_zeroed_page() */
@@ -246,7 +255,7 @@
}
if (filp->f_flags & O_NONBLOCK) {
/* Indicate we are open */
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
tty_port_raise_dtr_rts(port);
port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
@@ -270,7 +279,7 @@
while (1) {
/* Indicate we are open */
- if (tty->termios->c_cflag & CBAUD)
+ if (tty->termios.c_cflag & CBAUD)
tty_port_raise_dtr_rts(port);
prepare_to_wait(&port->open_wait, &wait, TASK_INTERRUPTIBLE);
@@ -369,7 +378,7 @@
/* Drop DTR/RTS if HUPCL is set. This causes any attached modem to
hang up the line */
- if (tty->termios->c_cflag & HUPCL)
+ if (tty->termios.c_cflag & HUPCL)
tty_port_lower_dtr_rts(port);
/* Don't call port->drop for the last reference. Callers will want
@@ -413,6 +422,14 @@
}
EXPORT_SYMBOL(tty_port_close);
+int tty_port_install(struct tty_port *port, struct tty_driver *driver,
+ struct tty_struct *tty)
+{
+ tty->port = port;
+ return tty_standard_install(driver, tty);
+}
+EXPORT_SYMBOL_GPL(tty_port_install);
+
int tty_port_open(struct tty_port *port, struct tty_struct *tty,
struct file *filp)
{
diff --git a/drivers/tty/vt/keyboard.c b/drivers/tty/vt/keyboard.c
index 48cc6f2..681765b 100644
--- a/drivers/tty/vt/keyboard.c
+++ b/drivers/tty/vt/keyboard.c
@@ -119,6 +119,7 @@
static struct input_handler kbd_handler;
static DEFINE_SPINLOCK(kbd_event_lock);
+static DEFINE_SPINLOCK(led_lock);
static unsigned long key_down[BITS_TO_LONGS(KEY_CNT)]; /* keyboard key bitmap */
static unsigned char shift_down[NR_SHIFT]; /* shift state counters.. */
static bool dead_key_next;
@@ -310,7 +311,7 @@
if (tty) {
tty_insert_flip_char(tty, ch, 0);
- con_schedule_flip(tty);
+ tty_schedule_flip(tty);
}
}
@@ -325,7 +326,7 @@
tty_insert_flip_char(tty, *cp, 0);
cp++;
}
- con_schedule_flip(tty);
+ tty_schedule_flip(tty);
}
static void applkey(struct vc_data *vc, int key, char mode)
@@ -586,7 +587,7 @@
if (!tty)
return;
tty_insert_flip_char(tty, 0, TTY_BREAK);
- con_schedule_flip(tty);
+ tty_schedule_flip(tty);
}
static void fn_scroll_forw(struct vc_data *vc)
@@ -984,7 +985,7 @@
* or (ii) whatever pattern of lights people want to show using KDSETLED,
* or (iii) specified bits of specified words in kernel memory.
*/
-unsigned char getledstate(void)
+static unsigned char getledstate(void)
{
return ledstate;
}
@@ -992,7 +993,7 @@
void setledstate(struct kbd_struct *kbd, unsigned int led)
{
unsigned long flags;
- spin_lock_irqsave(&kbd_event_lock, flags);
+ spin_lock_irqsave(&led_lock, flags);
if (!(led & ~7)) {
ledioctl = led;
kbd->ledmode = LED_SHOW_IOCTL;
@@ -1000,7 +1001,7 @@
kbd->ledmode = LED_SHOW_FLAGS;
set_leds();
- spin_unlock_irqrestore(&kbd_event_lock, flags);
+ spin_unlock_irqrestore(&led_lock, flags);
}
static inline unsigned char getleds(void)
@@ -1049,13 +1050,13 @@
*/
int vt_get_leds(int console, int flag)
{
- unsigned long flags;
struct kbd_struct * kbd = kbd_table + console;
int ret;
+ unsigned long flags;
- spin_lock_irqsave(&kbd_event_lock, flags);
+ spin_lock_irqsave(&led_lock, flags);
ret = vc_kbd_led(kbd, flag);
- spin_unlock_irqrestore(&kbd_event_lock, flags);
+ spin_unlock_irqrestore(&led_lock, flags);
return ret;
}
@@ -1091,11 +1092,11 @@
void vt_kbd_con_start(int console)
{
struct kbd_struct * kbd = kbd_table + console;
-/* unsigned long flags; */
-/* spin_lock_irqsave(&kbd_event_lock, flags); */
+ unsigned long flags;
+ spin_lock_irqsave(&led_lock, flags);
clr_vc_kbd_led(kbd, VC_SCROLLOCK);
set_leds();
-/* spin_unlock_irqrestore(&kbd_event_lock, flags); */
+ spin_unlock_irqrestore(&led_lock, flags);
}
/**
@@ -1104,21 +1105,15 @@
*
* Handle console stop. This is a wrapper for the VT layer
* so that we can keep kbd knowledge internal
- *
- * FIXME: We eventually need to hold the kbd lock here to protect
- * the LED updating. We can't do it yet because fn_hold calls stop_tty
- * and start_tty under the kbd_event_lock, while normal tty paths
- * don't hold the lock. We probably need to split out an LED lock
- * but not during an -rc release!
*/
void vt_kbd_con_stop(int console)
{
struct kbd_struct * kbd = kbd_table + console;
-/* unsigned long flags; */
-/* spin_lock_irqsave(&kbd_event_lock, flags); */
+ unsigned long flags;
+ spin_lock_irqsave(&led_lock, flags);
set_vc_kbd_led(kbd, VC_SCROLLOCK);
set_leds();
-/* spin_unlock_irqrestore(&kbd_event_lock, flags); */
+ spin_unlock_irqrestore(&led_lock, flags);
}
/*
@@ -1130,7 +1125,12 @@
*/
static void kbd_bh(unsigned long dummy)
{
- unsigned char leds = getleds();
+ unsigned char leds;
+ unsigned long flags;
+
+ spin_lock_irqsave(&led_lock, flags);
+ leds = getleds();
+ spin_unlock_irqrestore(&led_lock, flags);
if (leds != ledstate) {
input_handler_for_each_handle(&kbd_handler, &leds,
@@ -2035,11 +2035,11 @@
return -EPERM;
if (arg & ~0x77)
return -EINVAL;
- spin_lock_irqsave(&kbd_event_lock, flags);
+ spin_lock_irqsave(&led_lock, flags);
kbd->ledflagstate = (arg & 7);
kbd->default_ledflagstate = ((arg >> 4) & 7);
set_leds();
- spin_unlock_irqrestore(&kbd_event_lock, flags);
+ spin_unlock_irqrestore(&led_lock, flags);
return 0;
/* the ioctls below only set the lights, not the functions */
@@ -2134,8 +2134,10 @@
clr_vc_kbd_mode(kbd, VC_CRLF);
kbd->lockstate = 0;
kbd->slockstate = 0;
+ spin_lock(&led_lock);
kbd->ledmode = LED_SHOW_FLAGS;
kbd->ledflagstate = kbd->default_ledflagstate;
+ spin_unlock(&led_lock);
/* do not do set_leds here because this causes an endless tasklet loop
when the keyboard hasn't been initialized yet */
spin_unlock_irqrestore(&kbd_event_lock, flags);
diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c
index 84cbf29..e07ded3 100644
--- a/drivers/tty/vt/vt.c
+++ b/drivers/tty/vt/vt.c
@@ -1380,7 +1380,7 @@
tty_insert_flip_char(tty, *p, 0);
p++;
}
- con_schedule_flip(tty);
+ tty_schedule_flip(tty);
}
static void cursor_report(struct vc_data *vc, struct tty_struct *tty)
@@ -2792,41 +2792,52 @@
/*
* Allocate the console screen memory.
*/
-static int con_open(struct tty_struct *tty, struct file *filp)
+static int con_install(struct tty_driver *driver, struct tty_struct *tty)
{
unsigned int currcons = tty->index;
- int ret = 0;
+ struct vc_data *vc;
+ int ret;
console_lock();
- if (tty->driver_data == NULL) {
- ret = vc_allocate(currcons);
- if (ret == 0) {
- struct vc_data *vc = vc_cons[currcons].d;
+ ret = vc_allocate(currcons);
+ if (ret)
+ goto unlock;
- /* Still being freed */
- if (vc->port.tty) {
- console_unlock();
- return -ERESTARTSYS;
- }
- tty->driver_data = vc;
- vc->port.tty = tty;
+ vc = vc_cons[currcons].d;
- if (!tty->winsize.ws_row && !tty->winsize.ws_col) {
- tty->winsize.ws_row = vc_cons[currcons].d->vc_rows;
- tty->winsize.ws_col = vc_cons[currcons].d->vc_cols;
- }
- if (vc->vc_utf)
- tty->termios->c_iflag |= IUTF8;
- else
- tty->termios->c_iflag &= ~IUTF8;
- console_unlock();
- return ret;
- }
+ /* Still being freed */
+ if (vc->port.tty) {
+ ret = -ERESTARTSYS;
+ goto unlock;
}
+
+ ret = tty_port_install(&vc->port, driver, tty);
+ if (ret)
+ goto unlock;
+
+ tty->driver_data = vc;
+ vc->port.tty = tty;
+
+ if (!tty->winsize.ws_row && !tty->winsize.ws_col) {
+ tty->winsize.ws_row = vc_cons[currcons].d->vc_rows;
+ tty->winsize.ws_col = vc_cons[currcons].d->vc_cols;
+ }
+ if (vc->vc_utf)
+ tty->termios.c_iflag |= IUTF8;
+ else
+ tty->termios.c_iflag &= ~IUTF8;
+unlock:
console_unlock();
return ret;
}
+static int con_open(struct tty_struct *tty, struct file *filp)
+{
+ /* everything done in install */
+ return 0;
+}
+
+
static void con_close(struct tty_struct *tty, struct file *filp)
{
/* Nothing to do - we defer to shutdown */
@@ -2839,7 +2850,6 @@
console_lock();
vc->port.tty = NULL;
console_unlock();
- tty_shutdown(tty);
}
static int default_italic_color = 2; // green (ASCII)
@@ -2947,6 +2957,7 @@
console_initcall(con_init);
static const struct tty_operations con_ops = {
+ .install = con_install,
.open = con_open,
.close = con_close,
.write = con_write,
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index 56d6bf6..18f4e62 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -826,7 +826,7 @@
struct ktermios *termios_old)
{
struct acm *acm = tty->driver_data;
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
struct usb_cdc_line_coding newline;
int newctrl = acm->ctrlout;
diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
index f8ce97d..3b98fb7 100644
--- a/drivers/usb/serial/ark3116.c
+++ b/drivers/usb/serial/ark3116.c
@@ -215,7 +215,7 @@
static void ark3116_init_termios(struct tty_struct *tty)
{
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
*termios = tty_std_termios;
termios->c_cflag = B9600 | CS8
| CREAD | HUPCL | CLOCAL;
@@ -229,7 +229,7 @@
{
struct usb_serial *serial = port->serial;
struct ark3116_private *priv = usb_get_serial_port_data(port);
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
unsigned int cflag = termios->c_cflag;
int bps = tty_get_baud_rate(tty);
int quot;
diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c
index 6b73656..a46df73 100644
--- a/drivers/usb/serial/belkin_sa.c
+++ b/drivers/usb/serial/belkin_sa.c
@@ -307,7 +307,7 @@
unsigned long control_state;
int bad_flow_control;
speed_t baud;
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
iflag = termios->c_iflag;
cflag = termios->c_cflag;
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index 1e71079..ba5e07e1 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -469,7 +469,7 @@
if (tty) {
cp210x_get_termios_port(tty->driver_data,
- &tty->termios->c_cflag, &baud);
+ &tty->termios.c_cflag, &baud);
tty_encode_baud_rate(tty, baud, baud);
}
@@ -631,7 +631,7 @@
{
u32 baud;
- baud = tty->termios->c_ospeed;
+ baud = tty->termios.c_ospeed;
/* This maps the requested rate to a rate valid on cp2102 or cp2103,
* or to an arbitrary rate in [1M,2M].
@@ -665,10 +665,10 @@
if (!tty)
return;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
old_cflag = old_termios->c_cflag;
- if (tty->termios->c_ospeed != old_termios->c_ospeed)
+ if (tty->termios.c_ospeed != old_termios->c_ospeed)
cp210x_change_speed(tty, port, old_termios);
/* If the number of data bits is to be updated */
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index b78c34e..be34f15 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -922,38 +922,38 @@
early enough */
if (!priv->termios_initialized) {
if (priv->chiptype == CT_EARTHMATE) {
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = B4800 | CS8 | CREAD | HUPCL |
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = B4800 | CS8 | CREAD | HUPCL |
CLOCAL;
- tty->termios->c_ispeed = 4800;
- tty->termios->c_ospeed = 4800;
+ tty->termios.c_ispeed = 4800;
+ tty->termios.c_ospeed = 4800;
} else if (priv->chiptype == CT_CYPHIDCOM) {
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
CLOCAL;
- tty->termios->c_ispeed = 9600;
- tty->termios->c_ospeed = 9600;
+ tty->termios.c_ispeed = 9600;
+ tty->termios.c_ospeed = 9600;
} else if (priv->chiptype == CT_CA42V2) {
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL |
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = B9600 | CS8 | CREAD | HUPCL |
CLOCAL;
- tty->termios->c_ispeed = 9600;
- tty->termios->c_ospeed = 9600;
+ tty->termios.c_ispeed = 9600;
+ tty->termios.c_ospeed = 9600;
}
priv->termios_initialized = 1;
}
spin_unlock_irqrestore(&priv->lock, flags);
/* Unsupported features need clearing */
- tty->termios->c_cflag &= ~(CMSPAR|CRTSCTS);
+ tty->termios.c_cflag &= ~(CMSPAR|CRTSCTS);
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
/* check if there are new settings */
if (old_termios) {
spin_lock_irqsave(&priv->lock, flags);
- priv->tmp_termios = *(tty->termios);
+ priv->tmp_termios = tty->termios;
spin_unlock_irqrestore(&priv->lock, flags);
}
@@ -1021,7 +1021,7 @@
"4800bps.");
/* define custom termios settings for NMEA protocol */
- tty->termios->c_iflag /* input modes - */
+ tty->termios.c_iflag /* input modes - */
&= ~(IGNBRK /* disable ignore break */
| BRKINT /* disable break causes interrupt */
| PARMRK /* disable mark parity errors */
@@ -1031,10 +1031,10 @@
| ICRNL /* disable translate CR to NL */
| IXON); /* disable enable XON/XOFF flow control */
- tty->termios->c_oflag /* output modes */
+ tty->termios.c_oflag /* output modes */
&= ~OPOST; /* disable postprocess output char */
- tty->termios->c_lflag /* line discipline modes */
+ tty->termios.c_lflag /* line discipline modes */
&= ~(ECHO /* disable echo input characters */
| ECHONL /* disable echo new line */
| ICANON /* disable erase, kill, werase, and rprnt
@@ -1200,7 +1200,7 @@
/* hangup, as defined in acm.c... this might be a bad place for it
* though */
- if (tty && !(tty->termios->c_cflag & CLOCAL) &&
+ if (tty && !(tty->termios.c_cflag & CLOCAL) &&
!(priv->current_status & UART_CD)) {
dbg("%s - calling hangup", __func__);
tty_hangup(tty);
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index b5cd838..afd9d2e 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -687,8 +687,8 @@
struct usb_serial_port *port, struct ktermios *old_termios)
{
struct digi_port *priv = usb_get_serial_port_data(port);
- unsigned int iflag = tty->termios->c_iflag;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int iflag = tty->termios.c_iflag;
+ unsigned int cflag = tty->termios.c_cflag;
unsigned int old_iflag = old_termios->c_iflag;
unsigned int old_cflag = old_termios->c_cflag;
unsigned char buf[32];
@@ -709,7 +709,7 @@
/* don't set RTS if using hardware flow control */
/* and throttling input */
modem_signals = TIOCM_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags))
modem_signals |= TIOCM_RTS;
digi_set_modem_signals(port, modem_signals, 1);
@@ -748,7 +748,7 @@
}
}
/* set parity */
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) {
if (cflag&PARENB) {
@@ -1124,8 +1124,8 @@
/* set termios settings */
if (tty) {
- not_termios.c_cflag = ~tty->termios->c_cflag;
- not_termios.c_iflag = ~tty->termios->c_iflag;
+ not_termios.c_cflag = ~tty->termios.c_cflag;
+ not_termios.c_iflag = ~tty->termios.c_iflag;
digi_set_termios(tty, port, ¬_termios);
}
return 0;
@@ -1500,7 +1500,7 @@
rts = 0;
if (tty)
- rts = tty->termios->c_cflag & CRTSCTS;
+ rts = tty->termios.c_cflag & CRTSCTS;
if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) {
spin_lock(&priv->dp_port_lock);
diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c
index cdf61dd..34e8638 100644
--- a/drivers/usb/serial/empeg.c
+++ b/drivers/usb/serial/empeg.c
@@ -87,7 +87,7 @@
static void empeg_init_termios(struct tty_struct *tty)
{
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
/*
* The empeg-car player wants these particular tty settings.
diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 499b15fd..79451ee 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -173,10 +173,11 @@
/* FIXME - Stubbed out for now */
/* Don't change anything if nothing has changed */
- if (!tty_termios_hw_change(tty->termios, old_termios))
+ if (!tty_termios_hw_change(&tty->termios, old_termios))
return;
/* Do the real work here... */
+ tty_termios_copy_hw(&tty->termios, old_termios);
}
static int f81232_tiocmget(struct tty_struct *tty)
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index bc912e5..4b8b41a 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -2081,7 +2081,7 @@
{
struct usb_device *dev = port->serial->dev;
struct ftdi_private *priv = usb_get_serial_port_data(port);
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
unsigned int cflag = termios->c_cflag;
__u16 urb_value; /* will hold the new flags */
diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c
index e1f5ccd..f435575 100644
--- a/drivers/usb/serial/io_edgeport.c
+++ b/drivers/usb/serial/io_edgeport.c
@@ -1458,7 +1458,7 @@
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
edge_port->shadowMCR &= ~MCR_RTS;
status = send_cmd_write_uart_register(edge_port, MCR,
edge_port->shadowMCR);
@@ -1497,7 +1497,7 @@
return;
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
edge_port->shadowMCR |= MCR_RTS;
send_cmd_write_uart_register(edge_port, MCR,
edge_port->shadowMCR);
@@ -1516,9 +1516,9 @@
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned int cflag;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
dbg("%s - clfag %08x iflag %08x", __func__,
- tty->termios->c_cflag, tty->termios->c_iflag);
+ tty->termios.c_cflag, tty->termios.c_iflag);
dbg("%s - old clfag %08x old iflag %08x", __func__,
old_termios->c_cflag, old_termios->c_iflag);
@@ -1987,7 +1987,7 @@
tty = tty_port_tty_get(&edge_port->port->port);
if (tty) {
change_port_settings(tty,
- edge_port, tty->termios);
+ edge_port, &tty->termios);
tty_kref_put(tty);
}
@@ -2570,7 +2570,7 @@
return;
}
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
switch (cflag & CSIZE) {
case CS5:
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index 3936904..765978a 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -1870,7 +1870,7 @@
/* set up the port settings */
if (tty)
- edge_set_termios(tty, port, tty->termios);
+ edge_set_termios(tty, port, &tty->termios);
/* open up the port */
@@ -2272,13 +2272,13 @@
config = kmalloc (sizeof (*config), GFP_KERNEL);
if (!config) {
- *tty->termios = *old_termios;
+ tty->termios = *old_termios;
dev_err(&edge_port->port->dev, "%s - out of memory\n",
__func__);
return;
}
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
config->wFlags = 0;
@@ -2362,7 +2362,7 @@
} else
dbg("%s - OUTBOUND XON/XOFF is disabled", __func__);
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
/* Round the baud rate */
baud = tty_get_baud_rate(tty);
@@ -2408,10 +2408,10 @@
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned int cflag;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
dbg("%s - clfag %08x iflag %08x", __func__,
- tty->termios->c_cflag, tty->termios->c_iflag);
+ tty->termios.c_cflag, tty->termios.c_iflag);
dbg("%s - old clfag %08x old iflag %08x", __func__,
old_termios->c_cflag, old_termios->c_iflag);
dbg("%s - port %d", __func__, port->number);
diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c
index fc09414..5a96692 100644
--- a/drivers/usb/serial/ir-usb.c
+++ b/drivers/usb/serial/ir-usb.c
@@ -381,7 +381,7 @@
ir_xbof = ir_xbof_change(xbof) ;
/* Only speed changes are supported */
- tty_termios_copy_hw(tty->termios, old_termios);
+ tty_termios_copy_hw(&tty->termios, old_termios);
tty_encode_baud_rate(tty, baud, baud);
/*
diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c
index 22b1eb5..bf38640 100644
--- a/drivers/usb/serial/iuu_phoenix.c
+++ b/drivers/usb/serial/iuu_phoenix.c
@@ -921,7 +921,7 @@
{
const u32 supported_mask = CMSPAR|PARENB|PARODD;
struct iuu_private *priv = usb_get_serial_port_data(port);
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
int status;
u32 actual;
u32 parity;
@@ -930,7 +930,7 @@
u32 newval = cflag & supported_mask;
/* Just use the ospeed. ispeed should be the same. */
- baud = tty->termios->c_ospeed;
+ baud = tty->termios.c_ospeed;
dbg("%s - enter c_ospeed or baud=%d", __func__, baud);
@@ -961,13 +961,13 @@
* settings back over and then adjust them
*/
if (old_termios)
- tty_termios_copy_hw(tty->termios, old_termios);
+ tty_termios_copy_hw(&tty->termios, old_termios);
if (status != 0) /* Set failed - return old bits */
return;
/* Re-encode speed, parity and csize */
tty_encode_baud_rate(tty, baud, baud);
- tty->termios->c_cflag &= ~(supported_mask|CSIZE);
- tty->termios->c_cflag |= newval | csize;
+ tty->termios.c_cflag &= ~(supported_mask|CSIZE);
+ tty->termios.c_cflag |= newval | csize;
}
static void iuu_close(struct usb_serial_port *port)
@@ -993,14 +993,14 @@
static void iuu_init_termios(struct tty_struct *tty)
{
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = CLOCAL | CREAD | CS8 | B9600
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = CLOCAL | CREAD | CS8 | B9600
| TIOCM_CTS | CSTOPB | PARENB;
- tty->termios->c_ispeed = 9600;
- tty->termios->c_ospeed = 9600;
- tty->termios->c_lflag = 0;
- tty->termios->c_oflag = 0;
- tty->termios->c_iflag = 0;
+ tty->termios.c_ispeed = 9600;
+ tty->termios.c_ospeed = 9600;
+ tty->termios.c_lflag = 0;
+ tty->termios.c_oflag = 0;
+ tty->termios.c_iflag = 0;
}
static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port)
@@ -1012,8 +1012,8 @@
u32 actual;
struct iuu_private *priv = usb_get_serial_port_data(port);
- baud = tty->termios->c_ospeed;
- tty->termios->c_ispeed = baud;
+ baud = tty->termios.c_ospeed;
+ tty->termios.c_ispeed = baud;
/* Re-encode speed */
tty_encode_baud_rate(tty, baud, baud);
diff --git a/drivers/usb/serial/keyspan.c b/drivers/usb/serial/keyspan.c
index af0b70e..7bcbb47 100644
--- a/drivers/usb/serial/keyspan.c
+++ b/drivers/usb/serial/keyspan.c
@@ -158,7 +158,7 @@
p_priv = usb_get_serial_port_data(port);
d_details = p_priv->device_details;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
device_port = port->number - port->serial->minor;
/* Baud rate calculation takes baud rate as an integer
@@ -179,7 +179,7 @@
p_priv->flow_control = (cflag & CRTSCTS) ? flow_cts : flow_none;
/* Mark/Space not supported */
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
keyspan_send_setup(port, 0);
}
@@ -1086,7 +1086,7 @@
device_port = port->number - port->serial->minor;
if (tty) {
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
/* Baud rate calculation takes baud rate as an integer
so other rates can be generated if desired. */
baud_rate = tty_get_baud_rate(tty);
diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c
index a4ac3cf..dcada86 100644
--- a/drivers/usb/serial/keyspan_pda.c
+++ b/drivers/usb/serial/keyspan_pda.c
@@ -338,7 +338,7 @@
7[EOMS]1: 10 bit, b0/b7 is parity
7[EOMS]2: 11 bit, b0/b7 is parity, extra bit always (mark?)
- HW flow control is dictated by the tty->termios->c_cflags & CRTSCTS
+ HW flow control is dictated by the tty->termios.c_cflags & CRTSCTS
bit.
For now, just do baud. */
@@ -353,7 +353,7 @@
}
/* Only speed can change so copy the old h/w parameters
then encode the new speed */
- tty_termios_copy_hw(tty->termios, old_termios);
+ tty_termios_copy_hw(&tty->termios, old_termios);
tty_encode_baud_rate(tty, speed, speed);
}
diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c
index 5bed59c..def9ad2 100644
--- a/drivers/usb/serial/kl5kusb105.c
+++ b/drivers/usb/serial/kl5kusb105.c
@@ -311,12 +311,12 @@
/* set up termios structure */
spin_lock_irqsave(&priv->lock, flags);
- priv->termios.c_iflag = tty->termios->c_iflag;
- priv->termios.c_oflag = tty->termios->c_oflag;
- priv->termios.c_cflag = tty->termios->c_cflag;
- priv->termios.c_lflag = tty->termios->c_lflag;
+ priv->termios.c_iflag = tty->termios.c_iflag;
+ priv->termios.c_oflag = tty->termios.c_oflag;
+ priv->termios.c_cflag = tty->termios.c_cflag;
+ priv->termios.c_lflag = tty->termios.c_lflag;
for (i = 0; i < NCCS; i++)
- priv->termios.c_cc[i] = tty->termios->c_cc[i];
+ priv->termios.c_cc[i] = tty->termios.c_cc[i];
priv->cfg.pktlen = cfg->pktlen;
priv->cfg.baudrate = cfg->baudrate;
priv->cfg.databits = cfg->databits;
@@ -445,9 +445,9 @@
struct ktermios *old_termios)
{
struct klsi_105_private *priv = usb_get_serial_port_data(port);
- unsigned int iflag = tty->termios->c_iflag;
+ unsigned int iflag = tty->termios.c_iflag;
unsigned int old_iflag = old_termios->c_iflag;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
unsigned int old_cflag = old_termios->c_cflag;
struct klsi_105_port_settings *cfg;
unsigned long flags;
@@ -560,7 +560,7 @@
if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))
|| (cflag & CSTOPB) != (old_cflag & CSTOPB)) {
/* Not currently supported */
- tty->termios->c_cflag &= ~(PARENB|PARODD|CSTOPB);
+ tty->termios.c_cflag &= ~(PARENB|PARODD|CSTOPB);
#if 0
priv->last_lcr = 0;
@@ -587,7 +587,7 @@
|| (iflag & IXON) != (old_iflag & IXON)
|| (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
/* Not currently supported */
- tty->termios->c_cflag &= ~CRTSCTS;
+ tty->termios.c_cflag &= ~CRTSCTS;
/* Drop DTR/RTS if no flow control otherwise assert */
#if 0
if ((iflag & IXOFF) || (iflag & IXON) || (cflag & CRTSCTS))
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index fafeabb..bf5c749 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -191,11 +191,11 @@
static void kobil_init_termios(struct tty_struct *tty)
{
/* Default to echo off and other sane device settings */
- tty->termios->c_lflag = 0;
- tty->termios->c_lflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE);
- tty->termios->c_iflag = IGNBRK | IGNPAR | IXOFF;
+ tty->termios.c_lflag = 0;
+ tty->termios.c_iflag &= ~(ISIG | ICANON | ECHO | IEXTEN | XCASE);
+ tty->termios.c_iflag |= IGNBRK | IGNPAR | IXOFF;
/* do NOT translate CR to CR-NL (0x0A -> 0x0A 0x0D) */
- tty->termios->c_oflag &= ~ONLCR;
+ tty->termios.c_oflag &= ~ONLCR;
}
static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port)
@@ -581,14 +581,14 @@
struct kobil_private *priv;
int result;
unsigned short urb_val = 0;
- int c_cflag = tty->termios->c_cflag;
+ int c_cflag = tty->termios.c_cflag;
speed_t speed;
priv = usb_get_serial_port_data(port);
if (priv->device_type == KOBIL_USBTWIN_PRODUCT_ID ||
priv->device_type == KOBIL_KAAN_SIM_PRODUCT_ID) {
/* This device doesn't support ioctl calls */
- *tty->termios = *old;
+ tty_termios_copy_hw(&tty->termios, old);
return;
}
@@ -612,7 +612,7 @@
urb_val |= SUSBCR_SPASB_EvenParity;
} else
urb_val |= SUSBCR_SPASB_NoParity;
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
tty_encode_baud_rate(tty, speed, speed);
result = usb_control_msg(port->serial->dev,
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index a71fa0a..df98cff 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -454,7 +454,7 @@
* either.
*/
spin_lock_irqsave(&priv->lock, flags);
- if (tty && (tty->termios->c_cflag & CBAUD))
+ if (tty && (tty->termios.c_cflag & CBAUD))
priv->control_state = TIOCM_DTR | TIOCM_RTS;
else
priv->control_state = 0;
@@ -634,7 +634,7 @@
{
struct usb_serial *serial = port->serial;
struct mct_u232_private *priv = usb_get_serial_port_data(port);
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
unsigned int cflag = termios->c_cflag;
unsigned int old_cflag = old_termios->c_cflag;
unsigned long flags;
diff --git a/drivers/usb/serial/metro-usb.c b/drivers/usb/serial/metro-usb.c
index d47eb06..7ae9af6 100644
--- a/drivers/usb/serial/metro-usb.c
+++ b/drivers/usb/serial/metro-usb.c
@@ -130,20 +130,14 @@
/* Set the data read from the usb port into the serial port buffer. */
tty = tty_port_tty_get(&port->port);
- if (!tty) {
- dev_err(&port->dev, "%s - bad tty pointer - exiting\n",
- __func__);
- return;
- }
-
if (tty && urb->actual_length) {
/* Loop through the data copying each byte to the tty layer. */
tty_insert_flip_string(tty, data, urb->actual_length);
/* Force the data to the tty layer. */
tty_flip_buffer_push(tty);
+ tty_kref_put(tty);
}
- tty_kref_put(tty);
/* Set any port variables. */
spin_lock_irqsave(&metro_priv->lock, flags);
diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c
index a07dd3c..012f67b 100644
--- a/drivers/usb/serial/mos7720.c
+++ b/drivers/usb/serial/mos7720.c
@@ -1349,7 +1349,7 @@
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
mos7720_port->shadowMCR &= ~UART_MCR_RTS;
write_mos_reg(port->serial, port->number - port->serial->minor,
MCR, mos7720_port->shadowMCR);
@@ -1383,7 +1383,7 @@
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
mos7720_port->shadowMCR |= UART_MCR_RTS;
write_mos_reg(port->serial, port->number - port->serial->minor,
MCR, mos7720_port->shadowMCR);
@@ -1604,8 +1604,8 @@
lStop = 0x00; /* 1 stop bit */
lParity = 0x00; /* No parity */
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
/* Change the number of bits */
switch (cflag & CSIZE) {
@@ -1753,11 +1753,11 @@
dbg("%s\n", "setting termios - ASPIRE");
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
dbg("%s - cflag %08x iflag %08x", __func__,
- tty->termios->c_cflag,
- RELEVANT_IFLAG(tty->termios->c_iflag));
+ tty->termios.c_cflag,
+ RELEVANT_IFLAG(tty->termios.c_iflag));
dbg("%s - old cflag %08x old iflag %08x", __func__,
old_termios->c_cflag,
diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index 57eca24..d2f2b5d 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -1649,7 +1649,7 @@
return;
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
mos7840_port->shadowMCR &= ~MCR_RTS;
status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
mos7840_port->shadowMCR);
@@ -1692,7 +1692,7 @@
}
/* if we are implementing RTS/CTS, toggle that line */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
mos7840_port->shadowMCR |= MCR_RTS;
status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
mos7840_port->shadowMCR);
@@ -1998,8 +1998,8 @@
lStop = LCR_STOP_1;
lParity = LCR_PAR_NONE;
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
/* Change the number of bits */
if (cflag & CSIZE) {
@@ -2159,10 +2159,10 @@
dbg("%s", "setting termios - ");
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
dbg("%s - clfag %08x iflag %08x", __func__,
- tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
+ tty->termios.c_cflag, RELEVANT_IFLAG(tty->termios.c_iflag));
dbg("%s - old clfag %08x old iflag %08x", __func__,
old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
dbg("%s - port %d", __func__, port->number);
diff --git a/drivers/usb/serial/oti6858.c b/drivers/usb/serial/oti6858.c
index 5976b65..9f55556 100644
--- a/drivers/usb/serial/oti6858.c
+++ b/drivers/usb/serial/oti6858.c
@@ -404,10 +404,10 @@
static void oti6858_init_termios(struct tty_struct *tty)
{
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL;
- tty->termios->c_ispeed = 38400;
- tty->termios->c_ospeed = 38400;
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = B38400 | CS8 | CREAD | HUPCL | CLOCAL;
+ tty->termios.c_ispeed = 38400;
+ tty->termios.c_ospeed = 38400;
}
static void oti6858_set_termios(struct tty_struct *tty,
@@ -425,7 +425,7 @@
return;
}
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
spin_lock_irqsave(&priv->lock, flags);
divisor = priv->pending_setup.divisor;
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 13b8dd6..2b9108a 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -260,16 +260,16 @@
serial settings even to the same values as before. Thus
we actually need to filter in this specific case */
- if (!tty_termios_hw_change(tty->termios, old_termios))
+ if (!tty_termios_hw_change(&tty->termios, old_termios))
return;
- cflag = tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
buf = kzalloc(7, GFP_KERNEL);
if (!buf) {
dev_err(&port->dev, "%s - out of memory.\n", __func__);
/* Report back no change occurred */
- *tty->termios = *old_termios;
+ tty->termios = *old_termios;
return;
}
diff --git a/drivers/usb/serial/quatech2.c b/drivers/usb/serial/quatech2.c
index 151670b..7df9cdb 100644
--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -275,7 +275,7 @@
{
struct usb_device *dev = port->serial->dev;
struct qt2_port_private *port_priv;
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
u16 baud;
unsigned int cflag = termios->c_cflag;
u16 new_lcr = 0;
@@ -406,7 +406,7 @@
port_priv->device_port = (u8) device_port;
if (tty)
- qt2_set_termios(tty, port, tty->termios);
+ qt2_set_termios(tty, port, &tty->termios);
return 0;
diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c
index 0274710..b14ebbd 100644
--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -382,7 +382,7 @@
static void sierra_set_termios(struct tty_struct *tty,
struct usb_serial_port *port, struct ktermios *old_termios)
{
- tty_termios_copy_hw(tty->termios, old_termios);
+ tty_termios_copy_hw(&tty->termios, old_termios);
sierra_send_setup(port);
}
diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c
index cad6089..ab68a4d 100644
--- a/drivers/usb/serial/spcp8x5.c
+++ b/drivers/usb/serial/spcp8x5.c
@@ -316,10 +316,10 @@
static void spcp8x5_init_termios(struct tty_struct *tty)
{
/* for the 1st time call this function */
- *(tty->termios) = tty_std_termios;
- tty->termios->c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
- tty->termios->c_ispeed = 115200;
- tty->termios->c_ospeed = 115200;
+ tty->termios = tty_std_termios;
+ tty->termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
+ tty->termios.c_ispeed = 115200;
+ tty->termios.c_ospeed = 115200;
}
/* set the serial param for transfer. we should check if we really need to
@@ -330,7 +330,7 @@
struct usb_serial *serial = port->serial;
struct spcp8x5_private *priv = usb_get_serial_port_data(port);
unsigned long flags;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
unsigned int old_cflag = old_termios->c_cflag;
unsigned short uartdata;
unsigned char buf[2] = {0, 0};
@@ -340,7 +340,7 @@
/* check that they really want us to change something */
- if (!tty_termios_hw_change(tty->termios, old_termios))
+ if (!tty_termios_hw_change(&tty->termios, old_termios))
return;
/* set DTR/RTS active */
diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c
index 3fee23b..cf2d30c 100644
--- a/drivers/usb/serial/ssu100.c
+++ b/drivers/usb/serial/ssu100.c
@@ -216,7 +216,7 @@
struct ktermios *old_termios)
{
struct usb_device *dev = port->serial->dev;
- struct ktermios *termios = tty->termios;
+ struct ktermios *termios = &tty->termios;
u16 baud, divisor, remainder;
unsigned int cflag = termios->c_cflag;
u16 urb_value = 0; /* will hold the new flags */
@@ -322,7 +322,7 @@
dbg("%s - set uart failed", __func__);
if (tty)
- ssu100_set_termios(tty, port, tty->termios);
+ ssu100_set_termios(tty, port, &tty->termios);
return usb_serial_generic_open(tty, port);
}
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index a4404f5..f502a16 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -520,7 +520,7 @@
}
if (tty)
- ti_set_termios(tty, port, tty->termios);
+ ti_set_termios(tty, port, &tty->termios);
dbg("%s - sending TI_OPEN_PORT", __func__);
status = ti_command_out_sync(tdev, TI_OPEN_PORT,
@@ -562,7 +562,7 @@
usb_clear_halt(dev, port->read_urb->pipe);
if (tty)
- ti_set_termios(tty, port, tty->termios);
+ ti_set_termios(tty, port, &tty->termios);
dbg("%s - sending TI_OPEN_PORT (2)", __func__);
status = ti_command_out_sync(tdev, TI_OPEN_PORT,
@@ -831,8 +831,8 @@
int port_number = port->number - port->serial->minor;
unsigned int mcr;
- cflag = tty->termios->c_cflag;
- iflag = tty->termios->c_iflag;
+ cflag = tty->termios.c_cflag;
+ iflag = tty->termios.c_iflag;
dbg("%s - cflag %08x, iflag %08x", __func__, cflag, iflag);
dbg("%s - old clfag %08x, old iflag %08x", __func__,
@@ -871,7 +871,7 @@
}
/* CMSPAR isn't supported by this driver */
- tty->termios->c_cflag &= ~CMSPAR;
+ tty->termios.c_cflag &= ~CMSPAR;
if (cflag & PARENB) {
if (cflag & PARODD) {
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 27483f9..aa4b0d7 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -207,7 +207,7 @@
if (retval)
goto error_get_interface;
- retval = tty_standard_install(driver, tty);
+ retval = tty_port_install(&port->port, driver, tty);
if (retval)
goto error_init_termios;
@@ -305,8 +305,7 @@
* Do the resource freeing and refcount dropping for the port.
* Avoid freeing the console.
*
- * Called asynchronously after the last tty kref is dropped,
- * and the tty layer has already done the tty_shutdown(tty);
+ * Called asynchronously after the last tty kref is dropped.
*/
static void serial_cleanup(struct tty_struct *tty)
{
@@ -423,7 +422,7 @@
if (port->serial->type->set_termios)
port->serial->type->set_termios(tty, port, old);
else
- tty_termios_copy_hw(tty->termios, old);
+ tty_termios_copy_hw(&tty->termios, old);
}
static int serial_break(struct tty_struct *tty, int break_state)
diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c
index f35971d..7c3db9e 100644
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -67,7 +67,7 @@
struct usb_wwan_intf_private *intfdata = port->serial->private;
/* Doesn't support option setting */
- tty_termios_copy_hw(tty->termios, old_termios);
+ tty_termios_copy_hw(&tty->termios, old_termios);
if (intfdata->send_setup)
intfdata->send_setup(port);
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index 473635e..b36077d 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -724,7 +724,7 @@
{
struct usb_serial_port *port = tty->driver_data;
struct whiteheat_port_settings port_settings;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
port_settings.port = port->number + 1;
diff --git a/include/linux/Kbuild b/include/linux/Kbuild
index d9a7544..28ea2b4 100644
--- a/include/linux/Kbuild
+++ b/include/linux/Kbuild
@@ -84,7 +84,6 @@
header-y += capi.h
header-y += cciss_defs.h
header-y += cciss_ioctl.h
-header-y += cdk.h
header-y += cdrom.h
header-y += cgroupstats.h
header-y += chio.h
@@ -93,7 +92,6 @@
header-y += coda.h
header-y += coda_psdev.h
header-y += coff.h
-header-y += comstats.h
header-y += connector.h
header-y += const.h
header-y += cramfs_fs.h
@@ -140,7 +138,6 @@
header-y += futex.h
header-y += gameport.h
header-y += gen_stats.h
-header-y += generic_serial.h
header-y += genetlink.h
header-y += gfs2_ondisk.h
header-y += gigaset_dev.h
diff --git a/include/linux/cd1400.h b/include/linux/cd1400.h
deleted file mode 100644
index 1dc3ab0..0000000
--- a/include/linux/cd1400.h
+++ /dev/null
@@ -1,292 +0,0 @@
-/*****************************************************************************/
-
-/*
- * cd1400.h -- cd1400 UART hardware info.
- *
- * Copyright (C) 1996-1998 Stallion Technologies
- * Copyright (C) 1994-1996 Greg Ungerer.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _CD1400_H
-#define _CD1400_H
-/*****************************************************************************/
-
-/*
- * Define the number of async ports per cd1400 uart chip.
- */
-#define CD1400_PORTS 4
-
-/*
- * Define the cd1400 uarts internal FIFO sizes.
- */
-#define CD1400_TXFIFOSIZE 12
-#define CD1400_RXFIFOSIZE 12
-
-/*
- * Local RX FIFO thresh hold level. Also define the RTS thresh hold
- * based on the RX thresh hold.
- */
-#define FIFO_RXTHRESHOLD 6
-#define FIFO_RTSTHRESHOLD 7
-
-/*****************************************************************************/
-
-/*
- * Define the cd1400 register addresses. These are all the valid
- * registers with the cd1400. Some are global, some virtual, some
- * per port.
- */
-#define GFRCR 0x40
-#define CAR 0x68
-#define GCR 0x4b
-#define SVRR 0x67
-#define RICR 0x44
-#define TICR 0x45
-#define MICR 0x46
-#define RIR 0x6b
-#define TIR 0x6a
-#define MIR 0x69
-#define PPR 0x7e
-
-#define RIVR 0x43
-#define TIVR 0x42
-#define MIVR 0x41
-#define TDR 0x63
-#define RDSR 0x62
-#define MISR 0x4c
-#define EOSRR 0x60
-
-#define LIVR 0x18
-#define CCR 0x05
-#define SRER 0x06
-#define COR1 0x08
-#define COR2 0x09
-#define COR3 0x0a
-#define COR4 0x1e
-#define COR5 0x1f
-#define CCSR 0x0b
-#define RDCR 0x0e
-#define SCHR1 0x1a
-#define SCHR2 0x1b
-#define SCHR3 0x1c
-#define SCHR4 0x1d
-#define SCRL 0x22
-#define SCRH 0x23
-#define LNC 0x24
-#define MCOR1 0x15
-#define MCOR2 0x16
-#define RTPR 0x21
-#define MSVR1 0x6c
-#define MSVR2 0x6d
-#define PSVR 0x6f
-#define RBPR 0x78
-#define RCOR 0x7c
-#define TBPR 0x72
-#define TCOR 0x76
-
-/*****************************************************************************/
-
-/*
- * Define the set of baud rate clock divisors.
- */
-#define CD1400_CLK0 8
-#define CD1400_CLK1 32
-#define CD1400_CLK2 128
-#define CD1400_CLK3 512
-#define CD1400_CLK4 2048
-
-#define CD1400_NUMCLKS 5
-
-/*****************************************************************************/
-
-/*
- * Define the clock pre-scalar value to be a 5 ms clock. This should be
- * OK for now. It would probably be better to make it 10 ms, but we
- * can't fit that divisor into 8 bits!
- */
-#define PPR_SCALAR 244
-
-/*****************************************************************************/
-
-/*
- * Define values used to set character size options.
- */
-#define COR1_CHL5 0x00
-#define COR1_CHL6 0x01
-#define COR1_CHL7 0x02
-#define COR1_CHL8 0x03
-
-/*
- * Define values used to set the number of stop bits.
- */
-#define COR1_STOP1 0x00
-#define COR1_STOP15 0x04
-#define COR1_STOP2 0x08
-
-/*
- * Define values used to set the parity scheme in use.
- */
-#define COR1_PARNONE 0x00
-#define COR1_PARFORCE 0x20
-#define COR1_PARENB 0x40
-#define COR1_PARIGNORE 0x10
-
-#define COR1_PARODD 0x80
-#define COR1_PAREVEN 0x00
-
-#define COR2_IXM 0x80
-#define COR2_TXIBE 0x40
-#define COR2_ETC 0x20
-#define COR2_LLM 0x10
-#define COR2_RLM 0x08
-#define COR2_RTSAO 0x04
-#define COR2_CTSAE 0x02
-
-#define COR3_SCDRNG 0x80
-#define COR3_SCD34 0x40
-#define COR3_FCT 0x20
-#define COR3_SCD12 0x10
-
-/*
- * Define values used by COR4.
- */
-#define COR4_BRKINT 0x08
-#define COR4_IGNBRK 0x18
-
-/*****************************************************************************/
-
-/*
- * Define the modem control register values.
- * Note that the actual hardware is a little different to the conventional
- * pin names on the cd1400.
- */
-#define MSVR1_DTR 0x01
-#define MSVR1_DSR 0x10
-#define MSVR1_RI 0x20
-#define MSVR1_CTS 0x40
-#define MSVR1_DCD 0x80
-
-#define MSVR2_RTS 0x02
-#define MSVR2_DSR 0x10
-#define MSVR2_RI 0x20
-#define MSVR2_CTS 0x40
-#define MSVR2_DCD 0x80
-
-#define MCOR1_DCD 0x80
-#define MCOR1_CTS 0x40
-#define MCOR1_RI 0x20
-#define MCOR1_DSR 0x10
-
-#define MCOR2_DCD 0x80
-#define MCOR2_CTS 0x40
-#define MCOR2_RI 0x20
-#define MCOR2_DSR 0x10
-
-/*****************************************************************************/
-
-/*
- * Define the bits used with the service (interrupt) enable register.
- */
-#define SRER_NNDT 0x01
-#define SRER_TXEMPTY 0x02
-#define SRER_TXDATA 0x04
-#define SRER_RXDATA 0x10
-#define SRER_MODEM 0x80
-
-/*****************************************************************************/
-
-/*
- * Define operational commands for the command register.
- */
-#define CCR_RESET 0x80
-#define CCR_CORCHANGE 0x4e
-#define CCR_SENDCH 0x20
-#define CCR_CHANCTRL 0x10
-
-#define CCR_TXENABLE (CCR_CHANCTRL | 0x08)
-#define CCR_TXDISABLE (CCR_CHANCTRL | 0x04)
-#define CCR_RXENABLE (CCR_CHANCTRL | 0x02)
-#define CCR_RXDISABLE (CCR_CHANCTRL | 0x01)
-
-#define CCR_SENDSCHR1 (CCR_SENDCH | 0x01)
-#define CCR_SENDSCHR2 (CCR_SENDCH | 0x02)
-#define CCR_SENDSCHR3 (CCR_SENDCH | 0x03)
-#define CCR_SENDSCHR4 (CCR_SENDCH | 0x04)
-
-#define CCR_RESETCHAN (CCR_RESET | 0x00)
-#define CCR_RESETFULL (CCR_RESET | 0x01)
-#define CCR_TXFLUSHFIFO (CCR_RESET | 0x02)
-
-#define CCR_MAXWAIT 10000
-
-/*****************************************************************************/
-
-/*
- * Define the valid acknowledgement types (for hw ack cycle).
- */
-#define ACK_TYPMASK 0x07
-#define ACK_TYPTX 0x02
-#define ACK_TYPMDM 0x01
-#define ACK_TYPRXGOOD 0x03
-#define ACK_TYPRXBAD 0x07
-
-#define SVRR_RX 0x01
-#define SVRR_TX 0x02
-#define SVRR_MDM 0x04
-
-#define ST_OVERRUN 0x01
-#define ST_FRAMING 0x02
-#define ST_PARITY 0x04
-#define ST_BREAK 0x08
-#define ST_SCHAR1 0x10
-#define ST_SCHAR2 0x20
-#define ST_SCHAR3 0x30
-#define ST_SCHAR4 0x40
-#define ST_RANGE 0x70
-#define ST_SCHARMASK 0x70
-#define ST_TIMEOUT 0x80
-
-#define MISR_DCD 0x80
-#define MISR_CTS 0x40
-#define MISR_RI 0x20
-#define MISR_DSR 0x10
-
-/*****************************************************************************/
-
-/*
- * Defines for the CCSR status register.
- */
-#define CCSR_RXENABLED 0x80
-#define CCSR_RXFLOWON 0x40
-#define CCSR_RXFLOWOFF 0x20
-#define CCSR_TXENABLED 0x08
-#define CCSR_TXFLOWON 0x04
-#define CCSR_TXFLOWOFF 0x02
-
-/*****************************************************************************/
-
-/*
- * Define the embedded commands.
- */
-#define ETC_CMD 0x00
-#define ETC_STARTBREAK 0x81
-#define ETC_DELAY 0x82
-#define ETC_STOPBREAK 0x83
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/cdk.h b/include/linux/cdk.h
deleted file mode 100644
index 80093a8..0000000
--- a/include/linux/cdk.h
+++ /dev/null
@@ -1,486 +0,0 @@
-/*****************************************************************************/
-
-/*
- * cdk.h -- CDK interface definitions.
- *
- * Copyright (C) 1996-1998 Stallion Technologies
- * Copyright (C) 1994-1996 Greg Ungerer.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _CDK_H
-#define _CDK_H
-/*****************************************************************************/
-
-#pragma pack(2)
-
-/*
- * The following set of definitions is used to communicate with the
- * shared memory interface of the Stallion intelligent multiport serial
- * boards. The definitions in this file are taken directly from the
- * document titled "Generic Stackable Interface, Downloader and
- * Communications Development Kit".
- */
-
-/*
- * Define the set of important shared memory addresses. These are
- * required to initialize the board and get things started. All of these
- * addresses are relative to the start of the shared memory.
- */
-#define CDK_SIGADDR 0x200
-#define CDK_FEATADDR 0x280
-#define CDK_CDKADDR 0x300
-#define CDK_RDYADDR 0x262
-
-#define CDK_ALIVEMARKER 13
-
-/*
- * On hardware power up the ROMs located on the EasyConnection 8/64 will
- * fill out the following signature information into shared memory. This
- * way the host system can quickly determine that the board is present
- * and is operational.
- */
-typedef struct cdkecpsig {
- unsigned long magic;
- unsigned short romver;
- unsigned short cputype;
- unsigned char panelid[8];
-} cdkecpsig_t;
-
-#define ECP_MAGIC 0x21504345
-
-/*
- * On hardware power up the ROMs located on the ONboard, Stallion and
- * Brumbys will fill out the following signature information into shared
- * memory. This way the host system can quickly determine that the board
- * is present and is operational.
- */
-typedef struct cdkonbsig {
- unsigned short magic0;
- unsigned short magic1;
- unsigned short magic2;
- unsigned short magic3;
- unsigned short romver;
- unsigned short memoff;
- unsigned short memseg;
- unsigned short amask0;
- unsigned short pic;
- unsigned short status;
- unsigned short btype;
- unsigned short clkticks;
- unsigned short clkspeed;
- unsigned short amask1;
- unsigned short amask2;
-} cdkonbsig_t;
-
-#define ONB_MAGIC0 0xf2a7
-#define ONB_MAGIC1 0xa149
-#define ONB_MAGIC2 0x6352
-#define ONB_MAGIC3 0xf121
-
-/*
- * Define the feature area structure. The feature area is the set of
- * startup parameters used by the slave image when it starts executing.
- * They allow for the specification of buffer sizes, debug trace, etc.
- */
-typedef struct cdkfeature {
- unsigned long debug;
- unsigned long banner;
- unsigned long etype;
- unsigned long nrdevs;
- unsigned long brdspec;
- unsigned long txrqsize;
- unsigned long rxrqsize;
- unsigned long flags;
-} cdkfeature_t;
-
-#define ETYP_DDK 0
-#define ETYP_CDK 1
-
-/*
- * Define the CDK header structure. This is the info that the slave
- * environment sets up after it has been downloaded and started. It
- * essentially provides a memory map for the shared memory interface.
- */
-typedef struct cdkhdr {
- unsigned short command;
- unsigned short status;
- unsigned short port;
- unsigned short mode;
- unsigned long cmd_buf[14];
- unsigned short alive_cnt;
- unsigned short intrpt_mode;
- unsigned char intrpt_id[8];
- unsigned char ver_release;
- unsigned char ver_modification;
- unsigned char ver_fix;
- unsigned char deadman_restart;
- unsigned short deadman;
- unsigned short nrdevs;
- unsigned long memp;
- unsigned long hostp;
- unsigned long slavep;
- unsigned char hostreq;
- unsigned char slavereq;
- unsigned char cmd_reserved[30];
-} cdkhdr_t;
-
-#define MODE_DDK 0
-#define MODE_CDK 1
-
-#define IMD_INTR 0x0
-#define IMD_PPINTR 0x1
-#define IMD_POLL 0xff
-
-/*
- * Define the memory mapping structure. This structure is pointed to by
- * the memp field in the stlcdkhdr struct. As many as these structures
- * as required are laid out in shared memory to define how the rest of
- * shared memory is divided up. There will be one for each port.
- */
-typedef struct cdkmem {
- unsigned short dtype;
- unsigned long offset;
-} cdkmem_t;
-
-#define TYP_UNDEFINED 0x0
-#define TYP_ASYNCTRL 0x1
-#define TYP_ASYNC 0x20
-#define TYP_PARALLEL 0x40
-#define TYP_SYNCX21 0x60
-
-/*****************************************************************************/
-
-/*
- * Following is a set of defines and structures used to actually deal
- * with the serial ports on the board. Firstly is the set of commands
- * that can be applied to ports.
- */
-#define ASYCMD (((unsigned long) 'a') << 8)
-
-#define A_NULL (ASYCMD | 0)
-#define A_FLUSH (ASYCMD | 1)
-#define A_BREAK (ASYCMD | 2)
-#define A_GETPORT (ASYCMD | 3)
-#define A_SETPORT (ASYCMD | 4)
-#define A_SETPORTF (ASYCMD | 5)
-#define A_SETPORTFTX (ASYCMD | 6)
-#define A_SETPORTFRX (ASYCMD | 7)
-#define A_GETSIGNALS (ASYCMD | 8)
-#define A_SETSIGNALS (ASYCMD | 9)
-#define A_SETSIGNALSF (ASYCMD | 10)
-#define A_SETSIGNALSFTX (ASYCMD | 11)
-#define A_SETSIGNALSFRX (ASYCMD | 12)
-#define A_GETNOTIFY (ASYCMD | 13)
-#define A_SETNOTIFY (ASYCMD | 14)
-#define A_NOTIFY (ASYCMD | 15)
-#define A_PORTCTRL (ASYCMD | 16)
-#define A_GETSTATS (ASYCMD | 17)
-#define A_RQSTATE (ASYCMD | 18)
-#define A_FLOWSTATE (ASYCMD | 19)
-#define A_CLEARSTATS (ASYCMD | 20)
-
-/*
- * Define those arguments used for simple commands.
- */
-#define FLUSHRX 0x1
-#define FLUSHTX 0x2
-
-#define BREAKON -1
-#define BREAKOFF -2
-
-/*
- * Define the port setting structure, and all those defines that go along
- * with it. Basically this structure defines the characteristics of this
- * port: baud rate, chars, parity, input/output char cooking etc.
- */
-typedef struct asyport {
- unsigned long baudout;
- unsigned long baudin;
- unsigned long iflag;
- unsigned long oflag;
- unsigned long lflag;
- unsigned long pflag;
- unsigned long flow;
- unsigned long spare1;
- unsigned short vtime;
- unsigned short vmin;
- unsigned short txlo;
- unsigned short txhi;
- unsigned short rxlo;
- unsigned short rxhi;
- unsigned short rxhog;
- unsigned short spare2;
- unsigned char csize;
- unsigned char stopbs;
- unsigned char parity;
- unsigned char stopin;
- unsigned char startin;
- unsigned char stopout;
- unsigned char startout;
- unsigned char parmark;
- unsigned char brkmark;
- unsigned char cc[11];
-} asyport_t;
-
-#define PT_STOP1 0x0
-#define PT_STOP15 0x1
-#define PT_STOP2 0x2
-
-#define PT_NOPARITY 0x0
-#define PT_ODDPARITY 0x1
-#define PT_EVENPARITY 0x2
-#define PT_MARKPARITY 0x3
-#define PT_SPACEPARITY 0x4
-
-#define F_NONE 0x0
-#define F_IXON 0x1
-#define F_IXOFF 0x2
-#define F_IXANY 0x4
-#define F_IOXANY 0x8
-#define F_RTSFLOW 0x10
-#define F_CTSFLOW 0x20
-#define F_DTRFLOW 0x40
-#define F_DCDFLOW 0x80
-#define F_DSROFLOW 0x100
-#define F_DSRIFLOW 0x200
-
-#define FI_NORX 0x1
-#define FI_RAW 0x2
-#define FI_ISTRIP 0x4
-#define FI_UCLC 0x8
-#define FI_INLCR 0x10
-#define FI_ICRNL 0x20
-#define FI_IGNCR 0x40
-#define FI_IGNBREAK 0x80
-#define FI_DSCRDBREAK 0x100
-#define FI_1MARKBREAK 0x200
-#define FI_2MARKBREAK 0x400
-#define FI_XCHNGBREAK 0x800
-#define FI_IGNRXERRS 0x1000
-#define FI_DSCDRXERRS 0x2000
-#define FI_1MARKRXERRS 0x4000
-#define FI_2MARKRXERRS 0x8000
-#define FI_XCHNGRXERRS 0x10000
-#define FI_DSCRDNULL 0x20000
-
-#define FO_OLCUC 0x1
-#define FO_ONLCR 0x2
-#define FO_OOCRNL 0x4
-#define FO_ONOCR 0x8
-#define FO_ONLRET 0x10
-#define FO_ONL 0x20
-#define FO_OBS 0x40
-#define FO_OVT 0x80
-#define FO_OFF 0x100
-#define FO_OTAB1 0x200
-#define FO_OTAB2 0x400
-#define FO_OTAB3 0x800
-#define FO_OCR1 0x1000
-#define FO_OCR2 0x2000
-#define FO_OCR3 0x4000
-#define FO_OFILL 0x8000
-#define FO_ODELL 0x10000
-
-#define P_RTSLOCK 0x1
-#define P_CTSLOCK 0x2
-#define P_MAPRTS 0x4
-#define P_MAPCTS 0x8
-#define P_LOOPBACK 0x10
-#define P_DTRFOLLOW 0x20
-#define P_FAKEDCD 0x40
-
-#define P_RXIMIN 0x10000
-#define P_RXITIME 0x20000
-#define P_RXTHOLD 0x40000
-
-/*
- * Define a structure to communicate serial port signal and data state
- * information.
- */
-typedef struct asysigs {
- unsigned long data;
- unsigned long signal;
- unsigned long sigvalue;
-} asysigs_t;
-
-#define DT_TXBUSY 0x1
-#define DT_TXEMPTY 0x2
-#define DT_TXLOW 0x4
-#define DT_TXHIGH 0x8
-#define DT_TXFULL 0x10
-#define DT_TXHOG 0x20
-#define DT_TXFLOWED 0x40
-#define DT_TXBREAK 0x80
-
-#define DT_RXBUSY 0x100
-#define DT_RXEMPTY 0x200
-#define DT_RXLOW 0x400
-#define DT_RXHIGH 0x800
-#define DT_RXFULL 0x1000
-#define DT_RXHOG 0x2000
-#define DT_RXFLOWED 0x4000
-#define DT_RXBREAK 0x8000
-
-#define SG_DTR 0x1
-#define SG_DCD 0x2
-#define SG_RTS 0x4
-#define SG_CTS 0x8
-#define SG_DSR 0x10
-#define SG_RI 0x20
-
-/*
- * Define the notification setting structure. This is used to tell the
- * port what events we want to be informed about. Fields here use the
- * same defines as for the asysigs structure above.
- */
-typedef struct asynotify {
- unsigned long ctrl;
- unsigned long data;
- unsigned long signal;
- unsigned long sigvalue;
-} asynotify_t;
-
-/*
- * Define the port control structure. It is used to do fine grain
- * control operations on the port.
- */
-typedef struct {
- unsigned long rxctrl;
- unsigned long txctrl;
- char rximdch;
- char tximdch;
- char spare1;
- char spare2;
-} asyctrl_t;
-
-#define CT_ENABLE 0x1
-#define CT_DISABLE 0x2
-#define CT_STOP 0x4
-#define CT_START 0x8
-#define CT_STARTFLOW 0x10
-#define CT_STOPFLOW 0x20
-#define CT_SENDCHR 0x40
-
-/*
- * Define the stats structure kept for each port. This is a useful set
- * of data collected for each port on the slave. The A_GETSTATS command
- * is used to retrieve this data from the slave.
- */
-typedef struct asystats {
- unsigned long opens;
- unsigned long txchars;
- unsigned long rxchars;
- unsigned long txringq;
- unsigned long rxringq;
- unsigned long txmsgs;
- unsigned long rxmsgs;
- unsigned long txflushes;
- unsigned long rxflushes;
- unsigned long overruns;
- unsigned long framing;
- unsigned long parity;
- unsigned long ringover;
- unsigned long lost;
- unsigned long rxstart;
- unsigned long rxstop;
- unsigned long txstart;
- unsigned long txstop;
- unsigned long dcdcnt;
- unsigned long dtrcnt;
- unsigned long ctscnt;
- unsigned long rtscnt;
- unsigned long dsrcnt;
- unsigned long ricnt;
- unsigned long txbreaks;
- unsigned long rxbreaks;
- unsigned long signals;
- unsigned long state;
- unsigned long hwid;
-} asystats_t;
-
-/*****************************************************************************/
-
-/*
- * All command and control communication with a device on the slave is
- * via a control block in shared memory. Each device has its own control
- * block, defined by the following structure. The control block allows
- * the host to open, close and control the device on the slave.
- */
-typedef struct cdkctrl {
- unsigned char open;
- unsigned char close;
- unsigned long openarg;
- unsigned long closearg;
- unsigned long cmd;
- unsigned long status;
- unsigned long args[32];
-} cdkctrl_t;
-
-/*
- * Each device on the slave passes data to and from the host via a ring
- * queue in shared memory. Define a ring queue structure to hold the
- * vital information about each ring queue. Two ring queues will be
- * allocated for each port, one for receive data and one for transmit
- * data.
- */
-typedef struct cdkasyrq {
- unsigned long offset;
- unsigned short size;
- unsigned short head;
- unsigned short tail;
-} cdkasyrq_t;
-
-/*
- * Each asynchronous port is defined in shared memory by the following
- * structure. It contains a control block to command a device, and also
- * the necessary data channel information as well.
- */
-typedef struct cdkasy {
- cdkctrl_t ctrl;
- unsigned short notify;
- asynotify_t changed;
- unsigned short receive;
- cdkasyrq_t rxq;
- unsigned short transmit;
- cdkasyrq_t txq;
-} cdkasy_t;
-
-#pragma pack()
-
-/*****************************************************************************/
-
-/*
- * Define the set of ioctls used by the driver to do special things
- * to the board. These include interrupting it, and initializing
- * the driver after board startup and shutdown.
- */
-#include <linux/ioctl.h>
-
-#define STL_BINTR _IO('s',20)
-#define STL_BSTART _IO('s',21)
-#define STL_BSTOP _IO('s',22)
-#define STL_BRESET _IO('s',23)
-
-/*
- * Define a set of ioctl extensions, used to get at special stuff.
- */
-#define STL_GETPFLAG _IO('s',80)
-#define STL_SETPFLAG _IO('s',81)
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/comstats.h b/include/linux/comstats.h
deleted file mode 100644
index 3f5ea8e..0000000
--- a/include/linux/comstats.h
+++ /dev/null
@@ -1,119 +0,0 @@
-/*****************************************************************************/
-
-/*
- * comstats.h -- Serial Port Stats.
- *
- * Copyright (C) 1996-1998 Stallion Technologies
- * Copyright (C) 1994-1996 Greg Ungerer.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _COMSTATS_H
-#define _COMSTATS_H
-/*****************************************************************************/
-
-/*
- * Serial port stats structure. The structure itself is UART
- * independent, but some fields may be UART/driver specific (for
- * example state).
- */
-
-typedef struct {
- unsigned long brd;
- unsigned long panel;
- unsigned long port;
- unsigned long hwid;
- unsigned long type;
- unsigned long txtotal;
- unsigned long rxtotal;
- unsigned long txbuffered;
- unsigned long rxbuffered;
- unsigned long rxoverrun;
- unsigned long rxparity;
- unsigned long rxframing;
- unsigned long rxlost;
- unsigned long txbreaks;
- unsigned long rxbreaks;
- unsigned long txxon;
- unsigned long txxoff;
- unsigned long rxxon;
- unsigned long rxxoff;
- unsigned long txctson;
- unsigned long txctsoff;
- unsigned long rxrtson;
- unsigned long rxrtsoff;
- unsigned long modem;
- unsigned long state;
- unsigned long flags;
- unsigned long ttystate;
- unsigned long cflags;
- unsigned long iflags;
- unsigned long oflags;
- unsigned long lflags;
- unsigned long signals;
-} comstats_t;
-
-
-/*
- * Board stats structure. Returns useful info about the board.
- */
-
-#define COM_MAXPANELS 8
-
-typedef struct {
- unsigned long panel;
- unsigned long type;
- unsigned long hwid;
- unsigned long nrports;
-} companel_t;
-
-typedef struct {
- unsigned long brd;
- unsigned long type;
- unsigned long hwid;
- unsigned long state;
- unsigned long ioaddr;
- unsigned long ioaddr2;
- unsigned long memaddr;
- unsigned long irq;
- unsigned long nrpanels;
- unsigned long nrports;
- companel_t panels[COM_MAXPANELS];
-} combrd_t;
-
-
-/*
- * Define the ioctl operations for stats stuff.
- */
-#include <linux/ioctl.h>
-
-#define COM_GETPORTSTATS _IO('c',30)
-#define COM_CLRPORTSTATS _IO('c',31)
-#define COM_GETBRDSTATS _IO('c',32)
-
-
-/*
- * Define the set of ioctls that give user level access to the
- * private port, panel and board structures. The argument required
- * will be driver dependent!
- */
-#define COM_READPORT _IO('c',40)
-#define COM_READBOARD _IO('c',41)
-#define COM_READPANEL _IO('c',42)
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/generic_serial.h b/include/linux/generic_serial.h
deleted file mode 100644
index 79b3eb3..0000000
--- a/include/linux/generic_serial.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * generic_serial.h
- *
- * Copyright (C) 1998 R.E.Wolff@BitWizard.nl
- *
- * written for the SX serial driver.
- *
- * Version 0.1 -- December, 1998.
- */
-
-#ifndef GENERIC_SERIAL_H
-#define GENERIC_SERIAL_H
-
-#warning Use of this header is deprecated.
-#warning Since nobody sets the constants defined here for you, you should not, in any case, use them. Including the header is thus pointless.
-
-/* Flags */
-/* Warning: serial.h defines some ASYNC_ flags, they say they are "only"
- used in serial.c, but they are also used in all other serial drivers.
- Make sure they don't clash with these here... */
-#define GS_TX_INTEN 0x00800000
-#define GS_RX_INTEN 0x00400000
-#define GS_ACTIVE 0x00200000
-
-#define GS_TYPE_NORMAL 1
-
-#define GS_DEBUG_FLUSH 0x00000001
-#define GS_DEBUG_BTR 0x00000002
-#define GS_DEBUG_TERMIOS 0x00000004
-#define GS_DEBUG_STUFF 0x00000008
-#define GS_DEBUG_CLOSE 0x00000010
-#define GS_DEBUG_FLOW 0x00000020
-#define GS_DEBUG_WRITE 0x00000040
-
-#endif
diff --git a/include/linux/istallion.h b/include/linux/istallion.h
deleted file mode 100644
index ad700a6..0000000
--- a/include/linux/istallion.h
+++ /dev/null
@@ -1,123 +0,0 @@
-/*****************************************************************************/
-
-/*
- * istallion.h -- stallion intelligent multiport serial driver.
- *
- * Copyright (C) 1996-1998 Stallion Technologies
- * Copyright (C) 1994-1996 Greg Ungerer.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _ISTALLION_H
-#define _ISTALLION_H
-/*****************************************************************************/
-
-/*
- * Define important driver constants here.
- */
-#define STL_MAXBRDS 4
-#define STL_MAXPANELS 4
-#define STL_MAXPORTS 64
-#define STL_MAXCHANS (STL_MAXPORTS + 1)
-#define STL_MAXDEVS (STL_MAXBRDS * STL_MAXPORTS)
-
-
-/*
- * Define a set of structures to hold all the board/panel/port info
- * for our ports. These will be dynamically allocated as required at
- * driver initialization time.
- */
-
-/*
- * Port and board structures to hold status info about each object.
- * The board structure contains pointers to structures for each port
- * connected to it. Panels are not distinguished here, since
- * communication with the slave board will always be on a per port
- * basis.
- */
-struct stliport {
- unsigned long magic;
- struct tty_port port;
- unsigned int portnr;
- unsigned int panelnr;
- unsigned int brdnr;
- unsigned long state;
- unsigned int devnr;
- int baud_base;
- int custom_divisor;
- int closing_wait;
- int rc;
- int argsize;
- void *argp;
- unsigned int rxmarkmsk;
- wait_queue_head_t raw_wait;
- struct asysigs asig;
- unsigned long addr;
- unsigned long rxoffset;
- unsigned long txoffset;
- unsigned long sigs;
- unsigned long pflag;
- unsigned int rxsize;
- unsigned int txsize;
- unsigned char reqbit;
- unsigned char portidx;
- unsigned char portbit;
-};
-
-/*
- * Use a structure of function pointers to do board level operations.
- * These include, enable/disable, paging shared memory, interrupting, etc.
- */
-struct stlibrd {
- unsigned long magic;
- unsigned int brdnr;
- unsigned int brdtype;
- unsigned long state;
- unsigned int nrpanels;
- unsigned int nrports;
- unsigned int nrdevs;
- unsigned int iobase;
- int iosize;
- unsigned long memaddr;
- void __iomem *membase;
- unsigned long memsize;
- int pagesize;
- int hostoffset;
- int slaveoffset;
- int bitsize;
- int enabval;
- unsigned int panels[STL_MAXPANELS];
- int panelids[STL_MAXPANELS];
- void (*init)(struct stlibrd *brdp);
- void (*enable)(struct stlibrd *brdp);
- void (*reenable)(struct stlibrd *brdp);
- void (*disable)(struct stlibrd *brdp);
- void __iomem *(*getmemptr)(struct stlibrd *brdp, unsigned long offset, int line);
- void (*intr)(struct stlibrd *brdp);
- void (*reset)(struct stlibrd *brdp);
- struct stliport *ports[STL_MAXPORTS];
-};
-
-
-/*
- * Define MAGIC numbers used for above structures.
- */
-#define STLI_PORTMAGIC 0xe671c7a1
-#define STLI_BOARDMAGIC 0x4bc6c825
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/kbd_kern.h b/include/linux/kbd_kern.h
index daf4a3a..b7c8cdc 100644
--- a/include/linux/kbd_kern.h
+++ b/include/linux/kbd_kern.h
@@ -65,7 +65,6 @@
extern int kbd_init(void);
-extern unsigned char getledstate(void);
extern void setledstate(struct kbd_struct *kbd, unsigned int led);
extern int do_poke_blanked_console;
@@ -145,16 +144,4 @@
extern unsigned int keymap_count;
-/* console.c */
-
-static inline void con_schedule_flip(struct tty_struct *t)
-{
- unsigned long flags;
- spin_lock_irqsave(&t->buf.lock, flags);
- if (t->buf.tail != NULL)
- t->buf.tail->commit = t->buf.tail->used;
- spin_unlock_irqrestore(&t->buf.lock, flags);
- schedule_work(&t->buf.work);
-}
-
#endif
diff --git a/include/linux/sc26198.h b/include/linux/sc26198.h
deleted file mode 100644
index 7ca35ab..0000000
--- a/include/linux/sc26198.h
+++ /dev/null
@@ -1,533 +0,0 @@
-/*****************************************************************************/
-
-/*
- * sc26198.h -- SC26198 UART hardware info.
- *
- * Copyright (C) 1995-1998 Stallion Technologies
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _SC26198_H
-#define _SC26198_H
-/*****************************************************************************/
-
-/*
- * Define the number of async ports per sc26198 uart device.
- */
-#define SC26198_PORTS 8
-
-/*
- * Baud rate timing clocks. All derived from a master 14.7456 MHz clock.
- */
-#define SC26198_MASTERCLOCK 14745600L
-#define SC26198_DCLK (SC26198_MASTERCLOCK)
-#define SC26198_CCLK (SC26198_MASTERCLOCK / 2)
-#define SC26198_BCLK (SC26198_MASTERCLOCK / 4)
-
-/*
- * Define internal FIFO sizes for the 26198 ports.
- */
-#define SC26198_TXFIFOSIZE 16
-#define SC26198_RXFIFOSIZE 16
-
-/*****************************************************************************/
-
-/*
- * Global register definitions. These registers are global to each 26198
- * device, not specific ports on it.
- */
-#define TSTR 0x0d
-#define GCCR 0x0f
-#define ICR 0x1b
-#define WDTRCR 0x1d
-#define IVR 0x1f
-#define BRGTRUA 0x84
-#define GPOSR 0x87
-#define GPOC 0x8b
-#define UCIR 0x8c
-#define CIR 0x8c
-#define BRGTRUB 0x8d
-#define GRXFIFO 0x8e
-#define GTXFIFO 0x8e
-#define GCCR2 0x8f
-#define BRGTRLA 0x94
-#define GPOR 0x97
-#define GPOD 0x9b
-#define BRGTCR 0x9c
-#define GICR 0x9c
-#define BRGTRLB 0x9d
-#define GIBCR 0x9d
-#define GITR 0x9f
-
-/*
- * Per port channel registers. These are the register offsets within
- * the port address space, so need to have the port address (0 to 7)
- * inserted in bit positions 4:6.
- */
-#define MR0 0x00
-#define MR1 0x01
-#define IOPCR 0x02
-#define BCRBRK 0x03
-#define BCRCOS 0x04
-#define BCRX 0x06
-#define BCRA 0x07
-#define XONCR 0x08
-#define XOFFCR 0x09
-#define ARCR 0x0a
-#define RXCSR 0x0c
-#define TXCSR 0x0e
-#define MR2 0x80
-#define SR 0x81
-#define SCCR 0x81
-#define ISR 0x82
-#define IMR 0x82
-#define TXFIFO 0x83
-#define RXFIFO 0x83
-#define IPR 0x84
-#define IOPIOR 0x85
-#define XISR 0x86
-
-/*
- * For any given port calculate the address to use to access a specified
- * register. This is only used for unusual access, mostly this is done
- * through the assembler access routines.
- */
-#define SC26198_PORTREG(port,reg) ((((port) & 0x07) << 4) | (reg))
-
-/*****************************************************************************/
-
-/*
- * Global configuration control register bit definitions.
- */
-#define GCCR_NOACK 0x00
-#define GCCR_IVRACK 0x02
-#define GCCR_IVRCHANACK 0x04
-#define GCCR_IVRTYPCHANACK 0x06
-#define GCCR_ASYNCCYCLE 0x00
-#define GCCR_SYNCCYCLE 0x40
-
-/*****************************************************************************/
-
-/*
- * Mode register 0 bit definitions.
- */
-#define MR0_ADDRNONE 0x00
-#define MR0_AUTOWAKE 0x01
-#define MR0_AUTODOZE 0x02
-#define MR0_AUTOWAKEDOZE 0x03
-#define MR0_SWFNONE 0x00
-#define MR0_SWFTX 0x04
-#define MR0_SWFRX 0x08
-#define MR0_SWFRXTX 0x0c
-#define MR0_TXMASK 0x30
-#define MR0_TXEMPTY 0x00
-#define MR0_TXHIGH 0x10
-#define MR0_TXHALF 0x20
-#define MR0_TXRDY 0x00
-#define MR0_ADDRNT 0x00
-#define MR0_ADDRT 0x40
-#define MR0_SWFNT 0x00
-#define MR0_SWFT 0x80
-
-/*
- * Mode register 1 bit definitions.
- */
-#define MR1_CS5 0x00
-#define MR1_CS6 0x01
-#define MR1_CS7 0x02
-#define MR1_CS8 0x03
-#define MR1_PAREVEN 0x00
-#define MR1_PARODD 0x04
-#define MR1_PARENB 0x00
-#define MR1_PARFORCE 0x08
-#define MR1_PARNONE 0x10
-#define MR1_PARSPECIAL 0x18
-#define MR1_ERRCHAR 0x00
-#define MR1_ERRBLOCK 0x20
-#define MR1_ISRUNMASKED 0x00
-#define MR1_ISRMASKED 0x40
-#define MR1_AUTORTS 0x80
-
-/*
- * Mode register 2 bit definitions.
- */
-#define MR2_STOP1 0x00
-#define MR2_STOP15 0x01
-#define MR2_STOP2 0x02
-#define MR2_STOP916 0x03
-#define MR2_RXFIFORDY 0x00
-#define MR2_RXFIFOHALF 0x04
-#define MR2_RXFIFOHIGH 0x08
-#define MR2_RXFIFOFULL 0x0c
-#define MR2_AUTOCTS 0x10
-#define MR2_TXRTS 0x20
-#define MR2_MODENORM 0x00
-#define MR2_MODEAUTOECHO 0x40
-#define MR2_MODELOOP 0x80
-#define MR2_MODEREMECHO 0xc0
-
-/*****************************************************************************/
-
-/*
- * Baud Rate Generator (BRG) selector values.
- */
-#define BRG_50 0x00
-#define BRG_75 0x01
-#define BRG_150 0x02
-#define BRG_200 0x03
-#define BRG_300 0x04
-#define BRG_450 0x05
-#define BRG_600 0x06
-#define BRG_900 0x07
-#define BRG_1200 0x08
-#define BRG_1800 0x09
-#define BRG_2400 0x0a
-#define BRG_3600 0x0b
-#define BRG_4800 0x0c
-#define BRG_7200 0x0d
-#define BRG_9600 0x0e
-#define BRG_14400 0x0f
-#define BRG_19200 0x10
-#define BRG_28200 0x11
-#define BRG_38400 0x12
-#define BRG_57600 0x13
-#define BRG_115200 0x14
-#define BRG_230400 0x15
-#define BRG_GIN0 0x16
-#define BRG_GIN1 0x17
-#define BRG_CT0 0x18
-#define BRG_CT1 0x19
-#define BRG_RX2TX316 0x1b
-#define BRG_RX2TX31 0x1c
-
-#define SC26198_MAXBAUD 921600
-
-/*****************************************************************************/
-
-/*
- * Command register command definitions.
- */
-#define CR_NULL 0x04
-#define CR_ADDRNORMAL 0x0c
-#define CR_RXRESET 0x14
-#define CR_TXRESET 0x1c
-#define CR_CLEARRXERR 0x24
-#define CR_BREAKRESET 0x2c
-#define CR_TXSTARTBREAK 0x34
-#define CR_TXSTOPBREAK 0x3c
-#define CR_RTSON 0x44
-#define CR_RTSOFF 0x4c
-#define CR_ADDRINIT 0x5c
-#define CR_RXERRBLOCK 0x6c
-#define CR_TXSENDXON 0x84
-#define CR_TXSENDXOFF 0x8c
-#define CR_GANGXONSET 0x94
-#define CR_GANGXOFFSET 0x9c
-#define CR_GANGXONINIT 0xa4
-#define CR_GANGXOFFINIT 0xac
-#define CR_HOSTXON 0xb4
-#define CR_HOSTXOFF 0xbc
-#define CR_CANCELXOFF 0xc4
-#define CR_ADDRRESET 0xdc
-#define CR_RESETALLPORTS 0xf4
-#define CR_RESETALL 0xfc
-
-#define CR_RXENABLE 0x01
-#define CR_TXENABLE 0x02
-
-/*****************************************************************************/
-
-/*
- * Channel status register.
- */
-#define SR_RXRDY 0x01
-#define SR_RXFULL 0x02
-#define SR_TXRDY 0x04
-#define SR_TXEMPTY 0x08
-#define SR_RXOVERRUN 0x10
-#define SR_RXPARITY 0x20
-#define SR_RXFRAMING 0x40
-#define SR_RXBREAK 0x80
-
-#define SR_RXERRS (SR_RXPARITY | SR_RXFRAMING | SR_RXOVERRUN)
-
-/*****************************************************************************/
-
-/*
- * Interrupt status register and interrupt mask register bit definitions.
- */
-#define IR_TXRDY 0x01
-#define IR_RXRDY 0x02
-#define IR_RXBREAK 0x04
-#define IR_XONXOFF 0x10
-#define IR_ADDRRECOG 0x20
-#define IR_RXWATCHDOG 0x40
-#define IR_IOPORT 0x80
-
-/*****************************************************************************/
-
-/*
- * Interrupt vector register field definitions.
- */
-#define IVR_CHANMASK 0x07
-#define IVR_TYPEMASK 0x18
-#define IVR_CONSTMASK 0xc0
-
-#define IVR_RXDATA 0x10
-#define IVR_RXBADDATA 0x18
-#define IVR_TXDATA 0x08
-#define IVR_OTHER 0x00
-
-/*****************************************************************************/
-
-/*
- * BRG timer control register bit definitions.
- */
-#define BRGCTCR_DISABCLK0 0x00
-#define BRGCTCR_ENABCLK0 0x08
-#define BRGCTCR_DISABCLK1 0x00
-#define BRGCTCR_ENABCLK1 0x80
-
-#define BRGCTCR_0SCLK16 0x00
-#define BRGCTCR_0SCLK32 0x01
-#define BRGCTCR_0SCLK64 0x02
-#define BRGCTCR_0SCLK128 0x03
-#define BRGCTCR_0X1 0x04
-#define BRGCTCR_0X12 0x05
-#define BRGCTCR_0IO1A 0x06
-#define BRGCTCR_0GIN0 0x07
-
-#define BRGCTCR_1SCLK16 0x00
-#define BRGCTCR_1SCLK32 0x10
-#define BRGCTCR_1SCLK64 0x20
-#define BRGCTCR_1SCLK128 0x30
-#define BRGCTCR_1X1 0x40
-#define BRGCTCR_1X12 0x50
-#define BRGCTCR_1IO1B 0x60
-#define BRGCTCR_1GIN1 0x70
-
-/*****************************************************************************/
-
-/*
- * Watch dog timer enable register.
- */
-#define WDTRCR_ENABALL 0xff
-
-/*****************************************************************************/
-
-/*
- * XON/XOFF interrupt status register.
- */
-#define XISR_TXCHARMASK 0x03
-#define XISR_TXCHARNORMAL 0x00
-#define XISR_TXWAIT 0x01
-#define XISR_TXXOFFPEND 0x02
-#define XISR_TXXONPEND 0x03
-
-#define XISR_TXFLOWMASK 0x0c
-#define XISR_TXNORMAL 0x00
-#define XISR_TXSTOPPEND 0x04
-#define XISR_TXSTARTED 0x08
-#define XISR_TXSTOPPED 0x0c
-
-#define XISR_RXFLOWMASK 0x30
-#define XISR_RXFLOWNONE 0x00
-#define XISR_RXXONSENT 0x10
-#define XISR_RXXOFFSENT 0x20
-
-#define XISR_RXXONGOT 0x40
-#define XISR_RXXOFFGOT 0x80
-
-/*****************************************************************************/
-
-/*
- * Current interrupt register.
- */
-#define CIR_TYPEMASK 0xc0
-#define CIR_TYPEOTHER 0x00
-#define CIR_TYPETX 0x40
-#define CIR_TYPERXGOOD 0x80
-#define CIR_TYPERXBAD 0xc0
-
-#define CIR_RXDATA 0x80
-#define CIR_RXBADDATA 0x40
-#define CIR_TXDATA 0x40
-
-#define CIR_CHANMASK 0x07
-#define CIR_CNTMASK 0x38
-
-#define CIR_SUBTYPEMASK 0x38
-#define CIR_SUBNONE 0x00
-#define CIR_SUBCOS 0x08
-#define CIR_SUBADDR 0x10
-#define CIR_SUBXONXOFF 0x18
-#define CIR_SUBBREAK 0x28
-
-/*****************************************************************************/
-
-/*
- * Global interrupting channel register.
- */
-#define GICR_CHANMASK 0x07
-
-/*****************************************************************************/
-
-/*
- * Global interrupting byte count register.
- */
-#define GICR_COUNTMASK 0x0f
-
-/*****************************************************************************/
-
-/*
- * Global interrupting type register.
- */
-#define GITR_RXMASK 0xc0
-#define GITR_RXNONE 0x00
-#define GITR_RXBADDATA 0x80
-#define GITR_RXGOODDATA 0xc0
-#define GITR_TXDATA 0x20
-
-#define GITR_SUBTYPEMASK 0x07
-#define GITR_SUBNONE 0x00
-#define GITR_SUBCOS 0x01
-#define GITR_SUBADDR 0x02
-#define GITR_SUBXONXOFF 0x03
-#define GITR_SUBBREAK 0x05
-
-/*****************************************************************************/
-
-/*
- * Input port change register.
- */
-#define IPR_CTS 0x01
-#define IPR_DTR 0x02
-#define IPR_RTS 0x04
-#define IPR_DCD 0x08
-#define IPR_CTSCHANGE 0x10
-#define IPR_DTRCHANGE 0x20
-#define IPR_RTSCHANGE 0x40
-#define IPR_DCDCHANGE 0x80
-
-#define IPR_CHANGEMASK 0xf0
-
-/*****************************************************************************/
-
-/*
- * IO port interrupt and output register.
- */
-#define IOPR_CTS 0x01
-#define IOPR_DTR 0x02
-#define IOPR_RTS 0x04
-#define IOPR_DCD 0x08
-#define IOPR_CTSCOS 0x10
-#define IOPR_DTRCOS 0x20
-#define IOPR_RTSCOS 0x40
-#define IOPR_DCDCOS 0x80
-
-/*****************************************************************************/
-
-/*
- * IO port configuration register.
- */
-#define IOPCR_SETCTS 0x00
-#define IOPCR_SETDTR 0x04
-#define IOPCR_SETRTS 0x10
-#define IOPCR_SETDCD 0x00
-
-#define IOPCR_SETSIGS (IOPCR_SETRTS | IOPCR_SETRTS | IOPCR_SETDTR | IOPCR_SETDCD)
-
-/*****************************************************************************/
-
-/*
- * General purpose output select register.
- */
-#define GPORS_TXC1XA 0x08
-#define GPORS_TXC16XA 0x09
-#define GPORS_RXC16XA 0x0a
-#define GPORS_TXC16XB 0x0b
-#define GPORS_GPOR3 0x0c
-#define GPORS_GPOR2 0x0d
-#define GPORS_GPOR1 0x0e
-#define GPORS_GPOR0 0x0f
-
-/*****************************************************************************/
-
-/*
- * General purpose output register.
- */
-#define GPOR_0 0x01
-#define GPOR_1 0x02
-#define GPOR_2 0x04
-#define GPOR_3 0x08
-
-/*****************************************************************************/
-
-/*
- * General purpose output clock register.
- */
-#define GPORC_0NONE 0x00
-#define GPORC_0GIN0 0x01
-#define GPORC_0GIN1 0x02
-#define GPORC_0IO3A 0x02
-
-#define GPORC_1NONE 0x00
-#define GPORC_1GIN0 0x04
-#define GPORC_1GIN1 0x08
-#define GPORC_1IO3C 0x0c
-
-#define GPORC_2NONE 0x00
-#define GPORC_2GIN0 0x10
-#define GPORC_2GIN1 0x20
-#define GPORC_2IO3E 0x20
-
-#define GPORC_3NONE 0x00
-#define GPORC_3GIN0 0x40
-#define GPORC_3GIN1 0x80
-#define GPORC_3IO3G 0xc0
-
-/*****************************************************************************/
-
-/*
- * General purpose output data register.
- */
-#define GPOD_0MASK 0x03
-#define GPOD_0SET1 0x00
-#define GPOD_0SET0 0x01
-#define GPOD_0SETR0 0x02
-#define GPOD_0SETIO3B 0x03
-
-#define GPOD_1MASK 0x0c
-#define GPOD_1SET1 0x00
-#define GPOD_1SET0 0x04
-#define GPOD_1SETR0 0x08
-#define GPOD_1SETIO3D 0x0c
-
-#define GPOD_2MASK 0x30
-#define GPOD_2SET1 0x00
-#define GPOD_2SET0 0x10
-#define GPOD_2SETR0 0x20
-#define GPOD_2SETIO3F 0x30
-
-#define GPOD_3MASK 0xc0
-#define GPOD_3SET1 0x00
-#define GPOD_3SET0 0x40
-#define GPOD_3SETR0 0x80
-#define GPOD_3SETIO3H 0xc0
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/serial167.h b/include/linux/serial167.h
deleted file mode 100644
index 59c81b7..0000000
--- a/include/linux/serial167.h
+++ /dev/null
@@ -1,157 +0,0 @@
-/*
- * serial167.h
- *
- * Richard Hirst [richard@sleepie.demon.co.uk]
- *
- * Based on cyclades.h
- */
-
-struct cyclades_monitor {
- unsigned long int_count;
- unsigned long char_count;
- unsigned long char_max;
- unsigned long char_last;
-};
-
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct cyclades_port {
- int magic;
- int type;
- int card;
- int line;
- int flags; /* defined in tty.h */
- struct tty_struct *tty;
- int read_status_mask;
- int timeout;
- int xmit_fifo_size;
- int cor1,cor2,cor3,cor4,cor5,cor6,cor7;
- int tbpr,tco,rbpr,rco;
- int ignore_status_mask;
- int close_delay;
- int IER; /* Interrupt Enable Register */
- unsigned long last_active;
- int count; /* # of fd on device */
- int x_char; /* to be pushed out ASAP */
- int x_break;
- int blocked_open; /* # of blocked opens */
- unsigned char *xmit_buf;
- int xmit_head;
- int xmit_tail;
- int xmit_cnt;
- int default_threshold;
- int default_timeout;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
- struct cyclades_monitor mon;
-};
-
-#define CYCLADES_MAGIC 0x4359
-
-#define CYGETMON 0x435901
-#define CYGETTHRESH 0x435902
-#define CYSETTHRESH 0x435903
-#define CYGETDEFTHRESH 0x435904
-#define CYSETDEFTHRESH 0x435905
-#define CYGETTIMEOUT 0x435906
-#define CYSETTIMEOUT 0x435907
-#define CYGETDEFTIMEOUT 0x435908
-#define CYSETDEFTIMEOUT 0x435909
-
-#define CyMaxChipsPerCard 1
-
-/**** cd2401 registers ****/
-
-#define CyGFRCR (0x81)
-#define CyCCR (0x13)
-#define CyCLR_CHAN (0x40)
-#define CyINIT_CHAN (0x20)
-#define CyCHIP_RESET (0x10)
-#define CyENB_XMTR (0x08)
-#define CyDIS_XMTR (0x04)
-#define CyENB_RCVR (0x02)
-#define CyDIS_RCVR (0x01)
-#define CyCAR (0xee)
-#define CyIER (0x11)
-#define CyMdmCh (0x80)
-#define CyRxExc (0x20)
-#define CyRxData (0x08)
-#define CyTxMpty (0x02)
-#define CyTxRdy (0x01)
-#define CyLICR (0x26)
-#define CyRISR (0x89)
-#define CyTIMEOUT (0x80)
-#define CySPECHAR (0x70)
-#define CyOVERRUN (0x08)
-#define CyPARITY (0x04)
-#define CyFRAME (0x02)
-#define CyBREAK (0x01)
-#define CyREOIR (0x84)
-#define CyTEOIR (0x85)
-#define CyMEOIR (0x86)
-#define CyNOTRANS (0x08)
-#define CyRFOC (0x30)
-#define CyRDR (0xf8)
-#define CyTDR (0xf8)
-#define CyMISR (0x8b)
-#define CyRISR (0x89)
-#define CyTISR (0x8a)
-#define CyMSVR1 (0xde)
-#define CyMSVR2 (0xdf)
-#define CyDSR (0x80)
-#define CyDCD (0x40)
-#define CyCTS (0x20)
-#define CyDTR (0x02)
-#define CyRTS (0x01)
-#define CyRTPRL (0x25)
-#define CyRTPRH (0x24)
-#define CyCOR1 (0x10)
-#define CyPARITY_NONE (0x00)
-#define CyPARITY_E (0x40)
-#define CyPARITY_O (0xC0)
-#define Cy_5_BITS (0x04)
-#define Cy_6_BITS (0x05)
-#define Cy_7_BITS (0x06)
-#define Cy_8_BITS (0x07)
-#define CyCOR2 (0x17)
-#define CyETC (0x20)
-#define CyCtsAE (0x02)
-#define CyCOR3 (0x16)
-#define Cy_1_STOP (0x02)
-#define Cy_2_STOP (0x04)
-#define CyCOR4 (0x15)
-#define CyREC_FIFO (0x0F) /* Receive FIFO threshold */
-#define CyCOR5 (0x14)
-#define CyCOR6 (0x18)
-#define CyCOR7 (0x07)
-#define CyRBPR (0xcb)
-#define CyRCOR (0xc8)
-#define CyTBPR (0xc3)
-#define CyTCOR (0xc0)
-#define CySCHR1 (0x1f)
-#define CySCHR2 (0x1e)
-#define CyTPR (0xda)
-#define CyPILR1 (0xe3)
-#define CyPILR2 (0xe0)
-#define CyPILR3 (0xe1)
-#define CyCMR (0x1b)
-#define CyASYNC (0x02)
-#define CyLICR (0x26)
-#define CyLIVR (0x09)
-#define CySCRL (0x23)
-#define CySCRH (0x22)
-#define CyTFTC (0x80)
-
-
-/* max number of chars in the FIFO */
-
-#define CyMAX_CHAR_FIFO 12
-
-/***************************************************************************/
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index a416e92..c174c90 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -65,11 +65,38 @@
* platform device. Using these will make your driver
* dependent on the 8250 driver.
*/
-struct uart_port;
-struct uart_8250_port;
+
+struct uart_8250_port {
+ struct uart_port port;
+ struct timer_list timer; /* "no irq" timer */
+ struct list_head list; /* ports on this IRQ */
+ unsigned short capabilities; /* port capabilities */
+ unsigned short bugs; /* port bugs */
+ unsigned int tx_loadsz; /* transmit fifo load size */
+ unsigned char acr;
+ unsigned char ier;
+ unsigned char lcr;
+ unsigned char mcr;
+ unsigned char mcr_mask; /* mask of user bits */
+ unsigned char mcr_force; /* mask of forced bits */
+ unsigned char cur_iotype; /* Running I/O type */
+
+ /*
+ * Some bits in registers are cleared on a read, so they must
+ * be saved whenever the register is read but the bits will not
+ * be immediately processed.
+ */
+#define LSR_SAVE_FLAGS UART_LSR_BRK_ERROR_BITS
+ unsigned char lsr_saved_flags;
+#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
+ unsigned char msr_saved_flags;
+
+ /* 8250 specific callbacks */
+ int (*dl_read)(struct uart_8250_port *);
+ void (*dl_write)(struct uart_8250_port *, int);
+};
int serial8250_register_8250_port(struct uart_8250_port *);
-int serial8250_register_port(struct uart_port *);
void serial8250_unregister_port(int line);
void serial8250_suspend_port(int line);
void serial8250_resume_port(int line);
diff --git a/include/linux/stallion.h b/include/linux/stallion.h
deleted file mode 100644
index 336af33c..0000000
--- a/include/linux/stallion.h
+++ /dev/null
@@ -1,147 +0,0 @@
-/*****************************************************************************/
-
-/*
- * stallion.h -- stallion multiport serial driver.
- *
- * Copyright (C) 1996-1998 Stallion Technologies
- * Copyright (C) 1994-1996 Greg Ungerer.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*****************************************************************************/
-#ifndef _STALLION_H
-#define _STALLION_H
-/*****************************************************************************/
-
-/*
- * Define important driver constants here.
- */
-#define STL_MAXBRDS 4
-#define STL_MAXPANELS 4
-#define STL_MAXBANKS 8
-#define STL_PORTSPERPANEL 16
-#define STL_MAXPORTS 64
-#define STL_MAXDEVS (STL_MAXBRDS * STL_MAXPORTS)
-
-
-/*
- * Define a set of structures to hold all the board/panel/port info
- * for our ports. These will be dynamically allocated as required.
- */
-
-/*
- * Define a ring queue structure for each port. This will hold the
- * TX data waiting to be output. Characters are fed into this buffer
- * from the line discipline (or even direct from user space!) and
- * then fed into the UARTs during interrupts. Will use a classic ring
- * queue here for this. The good thing about this type of ring queue
- * is that the head and tail pointers can be updated without interrupt
- * protection - since "write" code only needs to change the head, and
- * interrupt code only needs to change the tail.
- */
-struct stlrq {
- char *buf;
- char *head;
- char *tail;
-};
-
-/*
- * Port, panel and board structures to hold status info about each.
- * The board structure contains pointers to structures for each panel
- * connected to it, and in turn each panel structure contains pointers
- * for each port structure for each port on that panel. Note that
- * the port structure also contains the board and panel number that it
- * is associated with, this makes it (fairly) easy to get back to the
- * board/panel info for a port.
- */
-struct stlport {
- unsigned long magic;
- struct tty_port port;
- unsigned int portnr;
- unsigned int panelnr;
- unsigned int brdnr;
- int ioaddr;
- int uartaddr;
- unsigned int pagenr;
- unsigned long istate;
- int baud_base;
- int custom_divisor;
- int close_delay;
- int closing_wait;
- int openwaitcnt;
- int brklen;
- unsigned int sigs;
- unsigned int rxignoremsk;
- unsigned int rxmarkmsk;
- unsigned int imr;
- unsigned int crenable;
- unsigned long clk;
- unsigned long hwid;
- void *uartp;
- comstats_t stats;
- struct stlrq tx;
-};
-
-struct stlpanel {
- unsigned long magic;
- unsigned int panelnr;
- unsigned int brdnr;
- unsigned int pagenr;
- unsigned int nrports;
- int iobase;
- void *uartp;
- void (*isr)(struct stlpanel *panelp, unsigned int iobase);
- unsigned int hwid;
- unsigned int ackmask;
- struct stlport *ports[STL_PORTSPERPANEL];
-};
-
-struct stlbrd {
- unsigned long magic;
- unsigned int brdnr;
- unsigned int brdtype;
- unsigned int state;
- unsigned int nrpanels;
- unsigned int nrports;
- unsigned int nrbnks;
- int irq;
- int irqtype;
- int (*isr)(struct stlbrd *brdp);
- unsigned int ioaddr1;
- unsigned int ioaddr2;
- unsigned int iosize1;
- unsigned int iosize2;
- unsigned int iostatus;
- unsigned int ioctrl;
- unsigned int ioctrlval;
- unsigned int hwid;
- unsigned long clk;
- unsigned int bnkpageaddr[STL_MAXBANKS];
- unsigned int bnkstataddr[STL_MAXBANKS];
- struct stlpanel *bnk2panel[STL_MAXBANKS];
- struct stlpanel *panels[STL_MAXPANELS];
-};
-
-
-/*
- * Define MAGIC numbers used for above structures.
- */
-#define STL_PORTMAGIC 0x5a7182c9
-#define STL_PANELMAGIC 0x7ef621a1
-#define STL_BOARDMAGIC 0xa2267f52
-
-/*****************************************************************************/
-#endif
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 9f47ab5..a39e723 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -103,28 +103,28 @@
#define TTY_PARITY 3
#define TTY_OVERRUN 4
-#define INTR_CHAR(tty) ((tty)->termios->c_cc[VINTR])
-#define QUIT_CHAR(tty) ((tty)->termios->c_cc[VQUIT])
-#define ERASE_CHAR(tty) ((tty)->termios->c_cc[VERASE])
-#define KILL_CHAR(tty) ((tty)->termios->c_cc[VKILL])
-#define EOF_CHAR(tty) ((tty)->termios->c_cc[VEOF])
-#define TIME_CHAR(tty) ((tty)->termios->c_cc[VTIME])
-#define MIN_CHAR(tty) ((tty)->termios->c_cc[VMIN])
-#define SWTC_CHAR(tty) ((tty)->termios->c_cc[VSWTC])
-#define START_CHAR(tty) ((tty)->termios->c_cc[VSTART])
-#define STOP_CHAR(tty) ((tty)->termios->c_cc[VSTOP])
-#define SUSP_CHAR(tty) ((tty)->termios->c_cc[VSUSP])
-#define EOL_CHAR(tty) ((tty)->termios->c_cc[VEOL])
-#define REPRINT_CHAR(tty) ((tty)->termios->c_cc[VREPRINT])
-#define DISCARD_CHAR(tty) ((tty)->termios->c_cc[VDISCARD])
-#define WERASE_CHAR(tty) ((tty)->termios->c_cc[VWERASE])
-#define LNEXT_CHAR(tty) ((tty)->termios->c_cc[VLNEXT])
-#define EOL2_CHAR(tty) ((tty)->termios->c_cc[VEOL2])
+#define INTR_CHAR(tty) ((tty)->termios.c_cc[VINTR])
+#define QUIT_CHAR(tty) ((tty)->termios.c_cc[VQUIT])
+#define ERASE_CHAR(tty) ((tty)->termios.c_cc[VERASE])
+#define KILL_CHAR(tty) ((tty)->termios.c_cc[VKILL])
+#define EOF_CHAR(tty) ((tty)->termios.c_cc[VEOF])
+#define TIME_CHAR(tty) ((tty)->termios.c_cc[VTIME])
+#define MIN_CHAR(tty) ((tty)->termios.c_cc[VMIN])
+#define SWTC_CHAR(tty) ((tty)->termios.c_cc[VSWTC])
+#define START_CHAR(tty) ((tty)->termios.c_cc[VSTART])
+#define STOP_CHAR(tty) ((tty)->termios.c_cc[VSTOP])
+#define SUSP_CHAR(tty) ((tty)->termios.c_cc[VSUSP])
+#define EOL_CHAR(tty) ((tty)->termios.c_cc[VEOL])
+#define REPRINT_CHAR(tty) ((tty)->termios.c_cc[VREPRINT])
+#define DISCARD_CHAR(tty) ((tty)->termios.c_cc[VDISCARD])
+#define WERASE_CHAR(tty) ((tty)->termios.c_cc[VWERASE])
+#define LNEXT_CHAR(tty) ((tty)->termios.c_cc[VLNEXT])
+#define EOL2_CHAR(tty) ((tty)->termios.c_cc[VEOL2])
-#define _I_FLAG(tty, f) ((tty)->termios->c_iflag & (f))
-#define _O_FLAG(tty, f) ((tty)->termios->c_oflag & (f))
-#define _C_FLAG(tty, f) ((tty)->termios->c_cflag & (f))
-#define _L_FLAG(tty, f) ((tty)->termios->c_lflag & (f))
+#define _I_FLAG(tty, f) ((tty)->termios.c_iflag & (f))
+#define _O_FLAG(tty, f) ((tty)->termios.c_oflag & (f))
+#define _C_FLAG(tty, f) ((tty)->termios.c_cflag & (f))
+#define _L_FLAG(tty, f) ((tty)->termios.c_lflag & (f))
#define I_IGNBRK(tty) _I_FLAG((tty), IGNBRK)
#define I_BRKINT(tty) _I_FLAG((tty), BRKINT)
@@ -271,7 +271,7 @@
struct mutex termios_mutex;
spinlock_t ctrl_lock;
/* Termios values are protected by the termios mutex */
- struct ktermios *termios, *termios_locked;
+ struct ktermios termios, termios_locked;
struct termiox *termiox; /* May be NULL for unsupported */
char name[64];
struct pid *pgrp; /* Protected by ctrl lock */
@@ -423,7 +423,6 @@
extern int tty_do_resize(struct tty_struct *tty, struct winsize *ws);
extern void tty_driver_remove_tty(struct tty_driver *driver,
struct tty_struct *tty);
-extern void tty_shutdown(struct tty_struct *tty);
extern void tty_free_termios(struct tty_struct *tty);
extern int is_current_pgrp_orphaned(void);
extern struct pid *tty_get_pgrp(struct tty_struct *tty);
@@ -497,6 +496,9 @@
#define tty_is_writelocked(tty) (mutex_is_locked(&tty->atomic_write_lock))
extern void tty_port_init(struct tty_port *port);
+extern struct device *tty_port_register_device(struct tty_port *port,
+ struct tty_driver *driver, unsigned index,
+ struct device *device);
extern int tty_port_alloc_xmit_buf(struct tty_port *port);
extern void tty_port_free_xmit_buf(struct tty_port *port);
extern void tty_port_put(struct tty_port *port);
@@ -521,6 +523,8 @@
extern void tty_port_close_end(struct tty_port *port, struct tty_struct *tty);
extern void tty_port_close(struct tty_port *port,
struct tty_struct *tty, struct file *filp);
+extern int tty_port_install(struct tty_port *port, struct tty_driver *driver,
+ struct tty_struct *tty);
extern int tty_port_open(struct tty_port *port,
struct tty_struct *tty, struct file *filp);
static inline int tty_port_users(struct tty_port *port)
diff --git a/include/linux/tty_driver.h b/include/linux/tty_driver.h
index 6e6dbb7..80e72dc 100644
--- a/include/linux/tty_driver.h
+++ b/include/linux/tty_driver.h
@@ -45,14 +45,9 @@
*
* void (*shutdown)(struct tty_struct * tty);
*
- * This routine is called synchronously when a particular tty device
- * is closed for the last time freeing up the resources.
- * Note that tty_shutdown() is not called if ops->shutdown is defined.
- * This means one is responsible to take care of calling ops->remove (e.g.
- * via tty_driver_remove_tty) and releasing tty->termios.
- * Note that this hook may be called from *all* the contexts where one
- * uses tty refcounting (e.g. tty_port_tty_get).
- *
+ * This routine is called under the tty lock when a particular tty device
+ * is closed for the last time. It executes before the tty resources
+ * are freed so may execute while another function holds a tty kref.
*
* void (*cleanup)(struct tty_struct * tty);
*
@@ -313,6 +308,7 @@
* Pointer to the tty data structures
*/
struct tty_struct **ttys;
+ struct tty_port **ports;
struct ktermios **termios;
void *driver_state;
diff --git a/include/net/irda/ircomm_tty.h b/include/net/irda/ircomm_tty.h
index 59ba38bc..80ffde3 100644
--- a/include/net/irda/ircomm_tty.h
+++ b/include/net/irda/ircomm_tty.h
@@ -52,21 +52,16 @@
/* Same for payload size. See qos.c for the smallest max data size */
#define IRCOMM_TTY_DATA_UNINITIALISED (64 - IRCOMM_TTY_HDR_UNINITIALISED)
-/* Those are really defined in include/linux/serial.h - Jean II */
-#define ASYNC_B_INITIALIZED 31 /* Serial port was initialized */
-#define ASYNC_B_NORMAL_ACTIVE 29 /* Normal device is active */
-#define ASYNC_B_CLOSING 27 /* Serial port is closing */
-
/*
* IrCOMM TTY driver state
*/
struct ircomm_tty_cb {
irda_queue_t queue; /* Must be first */
+ struct tty_port port;
magic_t magic;
int state; /* Connect state */
- struct tty_struct *tty;
struct ircomm_cb *ircomm; /* IrCOMM layer instance */
struct sk_buff *tx_skb; /* Transmit buffer */
@@ -80,7 +75,6 @@
LOCAL_FLOW flow; /* IrTTP flow status */
int line;
- unsigned long flags;
__u8 dlsap_sel;
__u8 slsap_sel;
@@ -97,19 +91,10 @@
void *skey;
void *ckey;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
struct timer_list watchdog_timer;
struct work_struct tqueue;
- unsigned short close_delay;
- unsigned short closing_wait; /* time to wait before closing */
-
- int open_count;
- int blocked_open; /* # of blocked opens */
-
/* Protect concurent access to :
- * o self->open_count
* o self->ctrl_skb
* o self->tx_skb
* Maybe other things may gain to be protected as well...
diff --git a/net/bluetooth/rfcomm/tty.c b/net/bluetooth/rfcomm/tty.c
index cb96077..87ddd05 100644
--- a/net/bluetooth/rfcomm/tty.c
+++ b/net/bluetooth/rfcomm/tty.c
@@ -861,7 +861,7 @@
static void rfcomm_tty_set_termios(struct tty_struct *tty, struct ktermios *old)
{
- struct ktermios *new = tty->termios;
+ struct ktermios *new = &tty->termios;
int old_baud_rate = tty_termios_baud_rate(old);
int new_baud_rate = tty_termios_baud_rate(new);
diff --git a/net/irda/ircomm/ircomm_param.c b/net/irda/ircomm/ircomm_param.c
index 8b915f3..3089391 100644
--- a/net/irda/ircomm/ircomm_param.c
+++ b/net/irda/ircomm/ircomm_param.c
@@ -99,7 +99,6 @@
*/
int ircomm_param_request(struct ircomm_tty_cb *self, __u8 pi, int flush)
{
- struct tty_struct *tty;
unsigned long flags;
struct sk_buff *skb;
int count;
@@ -109,10 +108,6 @@
IRDA_ASSERT(self != NULL, return -1;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
- tty = self->tty;
- if (!tty)
- return 0;
-
/* Make sure we don't send parameters for raw mode */
if (self->service_type == IRCOMM_3_WIRE_RAW)
return 0;
diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c
index 6b9d5a0..7a0d611 100644
--- a/net/irda/ircomm/ircomm_tty.c
+++ b/net/irda/ircomm/ircomm_tty.c
@@ -104,6 +104,35 @@
#endif /* CONFIG_PROC_FS */
};
+static void ircomm_port_raise_dtr_rts(struct tty_port *port, int raise)
+{
+ struct ircomm_tty_cb *self = container_of(port, struct ircomm_tty_cb,
+ port);
+ /*
+ * Here, we use to lock those two guys, but as ircomm_param_request()
+ * does it itself, I don't see the point (and I see the deadlock).
+ * Jean II
+ */
+ if (raise)
+ self->settings.dte |= IRCOMM_RTS | IRCOMM_DTR;
+ else
+ self->settings.dte &= ~(IRCOMM_RTS | IRCOMM_DTR);
+
+ ircomm_param_request(self, IRCOMM_DTE, TRUE);
+}
+
+static int ircomm_port_carrier_raised(struct tty_port *port)
+{
+ struct ircomm_tty_cb *self = container_of(port, struct ircomm_tty_cb,
+ port);
+ return self->settings.dce & IRCOMM_CD;
+}
+
+static const struct tty_port_operations ircomm_port_ops = {
+ .dtr_rts = ircomm_port_raise_dtr_rts,
+ .carrier_raised = ircomm_port_carrier_raised,
+};
+
/*
* Function ircomm_tty_init()
*
@@ -194,7 +223,7 @@
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
/* Check if already open */
- if (test_and_set_bit(ASYNC_B_INITIALIZED, &self->flags)) {
+ if (test_and_set_bit(ASYNCB_INITIALIZED, &self->port.flags)) {
IRDA_DEBUG(2, "%s(), already open so break out!\n", __func__ );
return 0;
}
@@ -231,7 +260,7 @@
return 0;
err:
- clear_bit(ASYNC_B_INITIALIZED, &self->flags);
+ clear_bit(ASYNCB_INITIALIZED, &self->port.flags);
return ret;
}
@@ -242,72 +271,62 @@
*
*/
static int ircomm_tty_block_til_ready(struct ircomm_tty_cb *self,
- struct file *filp)
+ struct tty_struct *tty, struct file *filp)
{
+ struct tty_port *port = &self->port;
DECLARE_WAITQUEUE(wait, current);
int retval;
int do_clocal = 0, extra_count = 0;
unsigned long flags;
- struct tty_struct *tty;
IRDA_DEBUG(2, "%s()\n", __func__ );
- tty = self->tty;
-
/*
* If non-blocking mode is set, or the port is not enabled,
* then make the check up front and then exit.
*/
if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
/* nonblock mode is set or port is not enabled */
- self->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
IRDA_DEBUG(1, "%s(), O_NONBLOCK requested!\n", __func__ );
return 0;
}
- if (tty->termios->c_cflag & CLOCAL) {
+ if (tty->termios.c_cflag & CLOCAL) {
IRDA_DEBUG(1, "%s(), doing CLOCAL!\n", __func__ );
do_clocal = 1;
}
/* Wait for carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
- * this loop, self->open_count is dropped by one, so that
+ * this loop, port->count is dropped by one, so that
* mgsl_close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
- add_wait_queue(&self->open_wait, &wait);
+ add_wait_queue(&port->open_wait, &wait);
IRDA_DEBUG(2, "%s(%d):block_til_ready before block on %s open_count=%d\n",
- __FILE__,__LINE__, tty->driver->name, self->open_count );
+ __FILE__, __LINE__, tty->driver->name, port->count);
- /* As far as I can see, we protect open_count - Jean II */
- spin_lock_irqsave(&self->spinlock, flags);
+ spin_lock_irqsave(&port->lock, flags);
if (!tty_hung_up_p(filp)) {
extra_count = 1;
- self->open_count--;
+ port->count--;
}
- spin_unlock_irqrestore(&self->spinlock, flags);
- self->blocked_open++;
+ spin_unlock_irqrestore(&port->lock, flags);
+ port->blocked_open++;
while (1) {
- if (tty->termios->c_cflag & CBAUD) {
- /* Here, we use to lock those two guys, but
- * as ircomm_param_request() does it itself,
- * I don't see the point (and I see the deadlock).
- * Jean II */
- self->settings.dte |= IRCOMM_RTS + IRCOMM_DTR;
-
- ircomm_param_request(self, IRCOMM_DTE, TRUE);
- }
+ if (tty->termios.c_cflag & CBAUD)
+ tty_port_raise_dtr_rts(port);
current->state = TASK_INTERRUPTIBLE;
if (tty_hung_up_p(filp) ||
- !test_bit(ASYNC_B_INITIALIZED, &self->flags)) {
- retval = (self->flags & ASYNC_HUP_NOTIFY) ?
+ !test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
}
@@ -317,8 +336,8 @@
* specified, we cannot return before the IrCOMM link is
* ready
*/
- if (!test_bit(ASYNC_B_CLOSING, &self->flags) &&
- (do_clocal || (self->settings.dce & IRCOMM_CD)) &&
+ if (!test_bit(ASYNCB_CLOSING, &port->flags) &&
+ (do_clocal || tty_port_carrier_raised(port)) &&
self->state == IRCOMM_TTY_READY)
{
break;
@@ -330,27 +349,27 @@
}
IRDA_DEBUG(1, "%s(%d):block_til_ready blocking on %s open_count=%d\n",
- __FILE__,__LINE__, tty->driver->name, self->open_count );
+ __FILE__, __LINE__, tty->driver->name, port->count);
schedule();
}
__set_current_state(TASK_RUNNING);
- remove_wait_queue(&self->open_wait, &wait);
+ remove_wait_queue(&port->open_wait, &wait);
if (extra_count) {
/* ++ is not atomic, so this should be protected - Jean II */
- spin_lock_irqsave(&self->spinlock, flags);
- self->open_count++;
- spin_unlock_irqrestore(&self->spinlock, flags);
+ spin_lock_irqsave(&port->lock, flags);
+ port->count++;
+ spin_unlock_irqrestore(&port->lock, flags);
}
- self->blocked_open--;
+ port->blocked_open--;
IRDA_DEBUG(1, "%s(%d):block_til_ready after blocking on %s open_count=%d\n",
- __FILE__,__LINE__, tty->driver->name, self->open_count);
+ __FILE__, __LINE__, tty->driver->name, port->count);
if (!retval)
- self->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
return retval;
}
@@ -381,6 +400,8 @@
return -ENOMEM;
}
+ tty_port_init(&self->port);
+ self->port.ops = &ircomm_port_ops;
self->magic = IRCOMM_TTY_MAGIC;
self->flow = FLOW_STOP;
@@ -388,13 +409,9 @@
INIT_WORK(&self->tqueue, ircomm_tty_do_softint);
self->max_header_size = IRCOMM_TTY_HDR_UNINITIALISED;
self->max_data_size = IRCOMM_TTY_DATA_UNINITIALISED;
- self->close_delay = 5*HZ/10;
- self->closing_wait = 30*HZ;
/* Init some important stuff */
init_timer(&self->watchdog_timer);
- init_waitqueue_head(&self->open_wait);
- init_waitqueue_head(&self->close_wait);
spin_lock_init(&self->spinlock);
/*
@@ -404,31 +421,32 @@
*
* Note this is completely usafe and doesn't work properly
*/
- tty->termios->c_iflag = 0;
- tty->termios->c_oflag = 0;
+ tty->termios.c_iflag = 0;
+ tty->termios.c_oflag = 0;
/* Insert into hash */
+ /* FIXME there is a window from find to here */
hashbin_insert(ircomm_tty, (irda_queue_t *) self, line, NULL);
}
/* ++ is not atomic, so this should be protected - Jean II */
- spin_lock_irqsave(&self->spinlock, flags);
- self->open_count++;
+ spin_lock_irqsave(&self->port.lock, flags);
+ self->port.count++;
tty->driver_data = self;
- self->tty = tty;
- spin_unlock_irqrestore(&self->spinlock, flags);
+ spin_unlock_irqrestore(&self->port.lock, flags);
+ tty_port_tty_set(&self->port, tty);
IRDA_DEBUG(1, "%s(), %s%d, count = %d\n", __func__ , tty->driver->name,
- self->line, self->open_count);
+ self->line, self->port.count);
/* Not really used by us, but lets do it anyway */
- self->tty->low_latency = (self->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ tty->low_latency = (self->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
/*
* If the port is the middle of closing, bail out now
*/
if (tty_hung_up_p(filp) ||
- test_bit(ASYNC_B_CLOSING, &self->flags)) {
+ test_bit(ASYNCB_CLOSING, &self->port.flags)) {
/* Hm, why are we blocking on ASYNC_CLOSING if we
* do return -EAGAIN/-ERESTARTSYS below anyway?
@@ -438,14 +456,15 @@
* probably better sleep uninterruptible?
*/
- if (wait_event_interruptible(self->close_wait, !test_bit(ASYNC_B_CLOSING, &self->flags))) {
+ if (wait_event_interruptible(self->port.close_wait,
+ !test_bit(ASYNCB_CLOSING, &self->port.flags))) {
IRDA_WARNING("%s - got signal while blocking on ASYNC_CLOSING!\n",
__func__);
return -ERESTARTSYS;
}
#ifdef SERIAL_DO_RESTART
- return (self->flags & ASYNC_HUP_NOTIFY) ?
+ return (self->port.flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
#else
return -EAGAIN;
@@ -469,7 +488,7 @@
if (ret)
return ret;
- ret = ircomm_tty_block_til_ready(self, filp);
+ ret = ircomm_tty_block_til_ready(self, tty, filp);
if (ret) {
IRDA_DEBUG(2,
"%s(), returning after block_til_ready with %d\n", __func__ ,
@@ -489,81 +508,22 @@
static void ircomm_tty_close(struct tty_struct *tty, struct file *filp)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
- unsigned long flags;
+ struct tty_port *port = &self->port;
IRDA_DEBUG(0, "%s()\n", __func__ );
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- spin_lock_irqsave(&self->spinlock, flags);
-
- if (tty_hung_up_p(filp)) {
- spin_unlock_irqrestore(&self->spinlock, flags);
-
- IRDA_DEBUG(0, "%s(), returning 1\n", __func__ );
+ if (tty_port_close_start(port, tty, filp) == 0)
return;
- }
-
- if ((tty->count == 1) && (self->open_count != 1)) {
- /*
- * Uh, oh. tty->count is 1, which means that the tty
- * structure will be freed. state->count should always
- * be one in these conditions. If it's greater than
- * one, we've got real problems, since it means the
- * serial port won't be shutdown.
- */
- IRDA_DEBUG(0, "%s(), bad serial port count; "
- "tty->count is 1, state->count is %d\n", __func__ ,
- self->open_count);
- self->open_count = 1;
- }
-
- if (--self->open_count < 0) {
- IRDA_ERROR("%s(), bad serial port count for ttys%d: %d\n",
- __func__, self->line, self->open_count);
- self->open_count = 0;
- }
- if (self->open_count) {
- spin_unlock_irqrestore(&self->spinlock, flags);
-
- IRDA_DEBUG(0, "%s(), open count > 0\n", __func__ );
- return;
- }
-
- /* Hum... Should be test_and_set_bit ??? - Jean II */
- set_bit(ASYNC_B_CLOSING, &self->flags);
-
- /* We need to unlock here (we were unlocking at the end of this
- * function), because tty_wait_until_sent() may schedule.
- * I don't know if the rest should be protected somehow,
- * so someone should check. - Jean II */
- spin_unlock_irqrestore(&self->spinlock, flags);
-
- /*
- * Now we wait for the transmit buffer to clear; and we notify
- * the line discipline to only process XON/XOFF characters.
- */
- tty->closing = 1;
- if (self->closing_wait != ASYNC_CLOSING_WAIT_NONE)
- tty_wait_until_sent_from_close(tty, self->closing_wait);
ircomm_tty_shutdown(self);
tty_driver_flush_buffer(tty);
- tty_ldisc_flush(tty);
- tty->closing = 0;
- self->tty = NULL;
-
- if (self->blocked_open) {
- if (self->close_delay)
- schedule_timeout_interruptible(self->close_delay);
- wake_up_interruptible(&self->open_wait);
- }
-
- self->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
- wake_up_interruptible(&self->close_wait);
+ tty_port_close_end(port, tty);
+ tty_port_tty_set(port, NULL);
}
/*
@@ -606,7 +566,7 @@
if (!self || self->magic != IRCOMM_TTY_MAGIC)
return;
- tty = self->tty;
+ tty = tty_port_tty_get(&self->port);
if (!tty)
return;
@@ -627,7 +587,7 @@
}
if (tty->hw_stopped)
- return;
+ goto put;
/* Unlink transmit buffer */
spin_lock_irqsave(&self->spinlock, flags);
@@ -646,6 +606,8 @@
/* Check if user (still) wants to be waken up */
tty_wakeup(tty);
+put:
+ tty_kref_put(tty);
}
/*
@@ -880,7 +842,7 @@
ircomm_tty_send_xchar(tty, STOP_CHAR(tty));
/* Hardware flow control? */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
self->settings.dte &= ~IRCOMM_RTS;
self->settings.dte |= IRCOMM_DELTA_RTS;
@@ -912,7 +874,7 @@
}
/* Using hardware flow control? */
- if (tty->termios->c_cflag & CRTSCTS) {
+ if (tty->termios.c_cflag & CRTSCTS) {
self->settings.dte |= (IRCOMM_RTS|IRCOMM_DELTA_RTS);
ircomm_param_request(self, IRCOMM_DTE, TRUE);
@@ -955,7 +917,7 @@
IRDA_DEBUG(0, "%s()\n", __func__ );
- if (!test_and_clear_bit(ASYNC_B_INITIALIZED, &self->flags))
+ if (!test_and_clear_bit(ASYNCB_INITIALIZED, &self->port.flags))
return;
ircomm_tty_detach_cable(self);
@@ -994,6 +956,7 @@
static void ircomm_tty_hangup(struct tty_struct *tty)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
+ struct tty_port *port = &self->port;
unsigned long flags;
IRDA_DEBUG(0, "%s()\n", __func__ );
@@ -1004,14 +967,17 @@
/* ircomm_tty_flush_buffer(tty); */
ircomm_tty_shutdown(self);
- /* I guess we need to lock here - Jean II */
- spin_lock_irqsave(&self->spinlock, flags);
- self->flags &= ~ASYNC_NORMAL_ACTIVE;
- self->tty = NULL;
- self->open_count = 0;
- spin_unlock_irqrestore(&self->spinlock, flags);
+ spin_lock_irqsave(&port->lock, flags);
+ port->flags &= ~ASYNC_NORMAL_ACTIVE;
+ if (port->tty) {
+ set_bit(TTY_IO_ERROR, &port->tty->flags);
+ tty_kref_put(port->tty);
+ }
+ port->tty = NULL;
+ port->count = 0;
+ spin_unlock_irqrestore(&port->lock, flags);
- wake_up_interruptible(&self->open_wait);
+ wake_up_interruptible(&port->open_wait);
}
/*
@@ -1071,20 +1037,20 @@
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- tty = self->tty;
+ tty = tty_port_tty_get(&self->port);
status = self->settings.dce;
if (status & IRCOMM_DCE_DELTA_ANY) {
/*wake_up_interruptible(&self->delta_msr_wait);*/
}
- if ((self->flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
+ if ((self->port.flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
IRDA_DEBUG(2,
"%s(), ircomm%d CD now %s...\n", __func__ , self->line,
(status & IRCOMM_CD) ? "on" : "off");
if (status & IRCOMM_CD) {
- wake_up_interruptible(&self->open_wait);
+ wake_up_interruptible(&self->port.open_wait);
} else {
IRDA_DEBUG(2,
"%s(), Doing serial hangup..\n", __func__ );
@@ -1092,10 +1058,10 @@
tty_hangup(tty);
/* Hangup will remote the tty, so better break out */
- return;
+ goto put;
}
}
- if (self->flags & ASYNC_CTS_FLOW) {
+ if (tty && self->port.flags & ASYNC_CTS_FLOW) {
if (tty->hw_stopped) {
if (status & IRCOMM_CTS) {
IRDA_DEBUG(2,
@@ -1103,10 +1069,10 @@
tty->hw_stopped = 0;
/* Wake up processes blocked on open */
- wake_up_interruptible(&self->open_wait);
+ wake_up_interruptible(&self->port.open_wait);
schedule_work(&self->tqueue);
- return;
+ goto put;
}
} else {
if (!(status & IRCOMM_CTS)) {
@@ -1116,6 +1082,8 @@
}
}
}
+put:
+ tty_kref_put(tty);
}
/*
@@ -1128,6 +1096,7 @@
struct sk_buff *skb)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) instance;
+ struct tty_struct *tty;
IRDA_DEBUG(2, "%s()\n", __func__ );
@@ -1135,7 +1104,8 @@
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
IRDA_ASSERT(skb != NULL, return -1;);
- if (!self->tty) {
+ tty = tty_port_tty_get(&self->port);
+ if (!tty) {
IRDA_DEBUG(0, "%s(), no tty!\n", __func__ );
return 0;
}
@@ -1146,7 +1116,7 @@
* Devices like WinCE can do this, and since they don't send any
* params, we can just as well declare the hardware for running.
*/
- if (self->tty->hw_stopped && (self->flow == FLOW_START)) {
+ if (tty->hw_stopped && (self->flow == FLOW_START)) {
IRDA_DEBUG(0, "%s(), polling for line settings!\n", __func__ );
ircomm_param_request(self, IRCOMM_POLL, TRUE);
@@ -1159,8 +1129,9 @@
* Use flip buffer functions since the code may be called from interrupt
* context
*/
- tty_insert_flip_string(self->tty, skb->data, skb->len);
- tty_flip_buffer_push(self->tty);
+ tty_insert_flip_string(tty, skb->data, skb->len);
+ tty_flip_buffer_push(tty);
+ tty_kref_put(tty);
/* No need to kfree_skb - see ircomm_ttp_data_indication() */
@@ -1211,12 +1182,13 @@
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- tty = self->tty;
+ tty = tty_port_tty_get(&self->port);
switch (cmd) {
case FLOW_START:
IRDA_DEBUG(2, "%s(), hw start!\n", __func__ );
- tty->hw_stopped = 0;
+ if (tty)
+ tty->hw_stopped = 0;
/* ircomm_tty_do_softint will take care of the rest */
schedule_work(&self->tqueue);
@@ -1224,15 +1196,19 @@
default: /* If we get here, something is very wrong, better stop */
case FLOW_STOP:
IRDA_DEBUG(2, "%s(), hw stopped!\n", __func__ );
- tty->hw_stopped = 1;
+ if (tty)
+ tty->hw_stopped = 1;
break;
}
+
+ tty_kref_put(tty);
self->flow = cmd;
}
#ifdef CONFIG_PROC_FS
static void ircomm_tty_line_info(struct ircomm_tty_cb *self, struct seq_file *m)
{
+ struct tty_struct *tty;
char sep;
seq_printf(m, "State: %s\n", ircomm_tty_state[self->state]);
@@ -1328,40 +1304,43 @@
seq_puts(m, "Flags:");
sep = ' ';
- if (self->flags & ASYNC_CTS_FLOW) {
+ if (self->port.flags & ASYNC_CTS_FLOW) {
seq_printf(m, "%cASYNC_CTS_FLOW", sep);
sep = '|';
}
- if (self->flags & ASYNC_CHECK_CD) {
+ if (self->port.flags & ASYNC_CHECK_CD) {
seq_printf(m, "%cASYNC_CHECK_CD", sep);
sep = '|';
}
- if (self->flags & ASYNC_INITIALIZED) {
+ if (self->port.flags & ASYNC_INITIALIZED) {
seq_printf(m, "%cASYNC_INITIALIZED", sep);
sep = '|';
}
- if (self->flags & ASYNC_LOW_LATENCY) {
+ if (self->port.flags & ASYNC_LOW_LATENCY) {
seq_printf(m, "%cASYNC_LOW_LATENCY", sep);
sep = '|';
}
- if (self->flags & ASYNC_CLOSING) {
+ if (self->port.flags & ASYNC_CLOSING) {
seq_printf(m, "%cASYNC_CLOSING", sep);
sep = '|';
}
- if (self->flags & ASYNC_NORMAL_ACTIVE) {
+ if (self->port.flags & ASYNC_NORMAL_ACTIVE) {
seq_printf(m, "%cASYNC_NORMAL_ACTIVE", sep);
sep = '|';
}
seq_putc(m, '\n');
seq_printf(m, "Role: %s\n", self->client ? "client" : "server");
- seq_printf(m, "Open count: %d\n", self->open_count);
+ seq_printf(m, "Open count: %d\n", self->port.count);
seq_printf(m, "Max data size: %d\n", self->max_data_size);
seq_printf(m, "Max header size: %d\n", self->max_header_size);
- if (self->tty)
+ tty = tty_port_tty_get(&self->port);
+ if (tty) {
seq_printf(m, "Hardware: %s\n",
- self->tty->hw_stopped ? "Stopped" : "Running");
+ tty->hw_stopped ? "Stopped" : "Running");
+ tty_kref_put(tty);
+ }
}
static int ircomm_tty_proc_show(struct seq_file *m, void *v)
diff --git a/net/irda/ircomm/ircomm_tty_attach.c b/net/irda/ircomm/ircomm_tty_attach.c
index b65d66e..3ab70e7 100644
--- a/net/irda/ircomm/ircomm_tty_attach.c
+++ b/net/irda/ircomm/ircomm_tty_attach.c
@@ -130,6 +130,8 @@
*/
int ircomm_tty_attach_cable(struct ircomm_tty_cb *self)
{
+ struct tty_struct *tty;
+
IRDA_DEBUG(0, "%s()\n", __func__ );
IRDA_ASSERT(self != NULL, return -1;);
@@ -142,7 +144,11 @@
}
/* Make sure nobody tries to write before the link is up */
- self->tty->hw_stopped = 1;
+ tty = tty_port_tty_get(&self->port);
+ if (tty) {
+ tty->hw_stopped = 1;
+ tty_kref_put(tty);
+ }
ircomm_tty_ias_register(self);
@@ -398,23 +404,26 @@
struct sk_buff *skb)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) instance;
+ struct tty_struct *tty;
IRDA_DEBUG(2, "%s()\n", __func__ );
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- if (!self->tty)
+ tty = tty_port_tty_get(&self->port);
+ if (!tty)
return;
/* This will stop control data transfers */
self->flow = FLOW_STOP;
/* Stop data transfers */
- self->tty->hw_stopped = 1;
+ tty->hw_stopped = 1;
ircomm_tty_do_event(self, IRCOMM_TTY_DISCONNECT_INDICATION, NULL,
NULL);
+ tty_kref_put(tty);
}
/*
@@ -550,12 +559,15 @@
*/
void ircomm_tty_link_established(struct ircomm_tty_cb *self)
{
+ struct tty_struct *tty;
+
IRDA_DEBUG(2, "%s()\n", __func__ );
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- if (!self->tty)
+ tty = tty_port_tty_get(&self->port);
+ if (!tty)
return;
del_timer(&self->watchdog_timer);
@@ -566,19 +578,22 @@
* will have to wait for the peer device (DCE) to raise the CTS
* line.
*/
- if ((self->flags & ASYNC_CTS_FLOW) && ((self->settings.dce & IRCOMM_CTS) == 0)) {
+ if ((self->port.flags & ASYNC_CTS_FLOW) &&
+ ((self->settings.dce & IRCOMM_CTS) == 0)) {
IRDA_DEBUG(0, "%s(), waiting for CTS ...\n", __func__ );
- return;
+ goto put;
} else {
IRDA_DEBUG(1, "%s(), starting hardware!\n", __func__ );
- self->tty->hw_stopped = 0;
+ tty->hw_stopped = 0;
/* Wake up processes blocked on open */
- wake_up_interruptible(&self->open_wait);
+ wake_up_interruptible(&self->port.open_wait);
}
schedule_work(&self->tqueue);
+put:
+ tty_kref_put(tty);
}
/*
@@ -977,14 +992,17 @@
ircomm_tty_next_state(self, IRCOMM_TTY_SEARCH);
ircomm_tty_start_watchdog_timer(self, 3*HZ);
- if (self->flags & ASYNC_CHECK_CD) {
+ if (self->port.flags & ASYNC_CHECK_CD) {
/* Drop carrier */
self->settings.dce = IRCOMM_DELTA_CD;
ircomm_tty_check_modem_status(self);
} else {
+ struct tty_struct *tty = tty_port_tty_get(&self->port);
IRDA_DEBUG(0, "%s(), hanging up!\n", __func__ );
- if (self->tty)
- tty_hangup(self->tty);
+ if (tty) {
+ tty_hangup(tty);
+ tty_kref_put(tty);
+ }
}
break;
default:
diff --git a/net/irda/ircomm/ircomm_tty_ioctl.c b/net/irda/ircomm/ircomm_tty_ioctl.c
index d0667d6..b343f50 100644
--- a/net/irda/ircomm/ircomm_tty_ioctl.c
+++ b/net/irda/ircomm/ircomm_tty_ioctl.c
@@ -52,17 +52,18 @@
* Change speed of the driver. If the remote device is a DCE, then this
* should make it change the speed of its serial port
*/
-static void ircomm_tty_change_speed(struct ircomm_tty_cb *self)
+static void ircomm_tty_change_speed(struct ircomm_tty_cb *self,
+ struct tty_struct *tty)
{
unsigned int cflag, cval;
int baud;
IRDA_DEBUG(2, "%s()\n", __func__ );
- if (!self->tty || !self->tty->termios || !self->ircomm)
+ if (!self->ircomm)
return;
- cflag = self->tty->termios->c_cflag;
+ cflag = tty->termios.c_cflag;
/* byte size and parity */
switch (cflag & CSIZE) {
@@ -81,7 +82,7 @@
cval |= IRCOMM_PARITY_EVEN;
/* Determine divisor based on baud rate */
- baud = tty_get_baud_rate(self->tty);
+ baud = tty_get_baud_rate(tty);
if (!baud)
baud = 9600; /* B0 transition handled in rs_set_termios */
@@ -90,19 +91,19 @@
/* CTS flow control flag and modem status interrupts */
if (cflag & CRTSCTS) {
- self->flags |= ASYNC_CTS_FLOW;
+ self->port.flags |= ASYNC_CTS_FLOW;
self->settings.flow_control |= IRCOMM_RTS_CTS_IN;
/* This got me. Bummer. Jean II */
if (self->service_type == IRCOMM_3_WIRE_RAW)
IRDA_WARNING("%s(), enabling RTS/CTS on link that doesn't support it (3-wire-raw)\n", __func__);
} else {
- self->flags &= ~ASYNC_CTS_FLOW;
+ self->port.flags &= ~ASYNC_CTS_FLOW;
self->settings.flow_control &= ~IRCOMM_RTS_CTS_IN;
}
if (cflag & CLOCAL)
- self->flags &= ~ASYNC_CHECK_CD;
+ self->port.flags &= ~ASYNC_CHECK_CD;
else
- self->flags |= ASYNC_CHECK_CD;
+ self->port.flags |= ASYNC_CHECK_CD;
#if 0
/*
* Set up parity check flag
@@ -148,18 +149,18 @@
struct ktermios *old_termios)
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
- unsigned int cflag = tty->termios->c_cflag;
+ unsigned int cflag = tty->termios.c_cflag;
IRDA_DEBUG(2, "%s()\n", __func__ );
if ((cflag == old_termios->c_cflag) &&
- (RELEVANT_IFLAG(tty->termios->c_iflag) ==
+ (RELEVANT_IFLAG(tty->termios.c_iflag) ==
RELEVANT_IFLAG(old_termios->c_iflag)))
{
return;
}
- ircomm_tty_change_speed(self);
+ ircomm_tty_change_speed(self, tty);
/* Handle transition to B0 status */
if ((old_termios->c_cflag & CBAUD) &&
@@ -172,7 +173,7 @@
if (!(old_termios->c_cflag & CBAUD) &&
(cflag & CBAUD)) {
self->settings.dte |= IRCOMM_DTR;
- if (!(tty->termios->c_cflag & CRTSCTS) ||
+ if (!(tty->termios.c_cflag & CRTSCTS) ||
!test_bit(TTY_THROTTLED, &tty->flags)) {
self->settings.dte |= IRCOMM_RTS;
}
@@ -181,7 +182,7 @@
/* Handle turning off CRTSCTS */
if ((old_termios->c_cflag & CRTSCTS) &&
- !(tty->termios->c_cflag & CRTSCTS))
+ !(tty->termios.c_cflag & CRTSCTS))
{
tty->hw_stopped = 0;
ircomm_tty_start(tty);
@@ -270,10 +271,10 @@
memset(&info, 0, sizeof(info));
info.line = self->line;
- info.flags = self->flags;
+ info.flags = self->port.flags;
info.baud_base = self->settings.data_rate;
- info.close_delay = self->close_delay;
- info.closing_wait = self->closing_wait;
+ info.close_delay = self->port.close_delay;
+ info.closing_wait = self->port.closing_wait;
/* For compatibility */
info.type = PORT_16550A;