| /* |
| * arch/arm/mach-footbridge/include/mach/hardware.h |
| * |
| * Copyright (C) 1998-1999 Russell King. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * This file contains the hardware definitions of the EBSA-285. |
| */ |
| #ifndef __ASM_ARCH_HARDWARE_H |
| #define __ASM_ARCH_HARDWARE_H |
| |
| /* Virtual Physical Size |
| * 0xff800000 0x40000000 1MB X-Bus |
| * 0xff000000 0x7c000000 1MB PCI I/O space |
| * 0xfe000000 0x42000000 1MB CSR |
| * 0xfd000000 0x78000000 1MB Outbound write flush (not supported) |
| * 0xfc000000 0x79000000 1MB PCI IACK/special space |
| * 0xfb000000 0x7a000000 16MB PCI Config type 1 |
| * 0xfa000000 0x7b000000 16MB PCI Config type 0 |
| * 0xf9000000 0x50000000 1MB Cache flush |
| * 0xf0000000 0x80000000 16MB ISA memory |
| */ |
| |
| #ifdef CONFIG_MMU |
| #define MMU_IO(a, b) (a) |
| #else |
| #define MMU_IO(a, b) (b) |
| #endif |
| |
| #define XBUS_SIZE 0x00100000 |
| #define XBUS_BASE MMU_IO(0xff800000, 0x40000000) |
| |
| #define ARMCSR_SIZE 0x00100000 |
| #define ARMCSR_BASE MMU_IO(0xfe000000, 0x42000000) |
| |
| #define WFLUSH_SIZE 0x00100000 |
| #define WFLUSH_BASE MMU_IO(0xfd000000, 0x78000000) |
| |
| #define PCIIACK_SIZE 0x00100000 |
| #define PCIIACK_BASE MMU_IO(0xfc000000, 0x79000000) |
| |
| #define PCICFG1_SIZE 0x01000000 |
| #define PCICFG1_BASE MMU_IO(0xfb000000, 0x7a000000) |
| |
| #define PCICFG0_SIZE 0x01000000 |
| #define PCICFG0_BASE MMU_IO(0xfa000000, 0x7b000000) |
| |
| #define PCIMEM_SIZE 0x01000000 |
| #define PCIMEM_BASE MMU_IO(0xf0000000, 0x80000000) |
| |
| #define XBUS_LEDS ((volatile unsigned char *)(XBUS_BASE + 0x12000)) |
| #define XBUS_LED_AMBER (1 << 0) |
| #define XBUS_LED_GREEN (1 << 1) |
| #define XBUS_LED_RED (1 << 2) |
| #define XBUS_LED_TOGGLE (1 << 8) |
| |
| #define XBUS_SWITCH ((volatile unsigned char *)(XBUS_BASE + 0x12000)) |
| #define XBUS_SWITCH_SWITCH ((*XBUS_SWITCH) & 15) |
| #define XBUS_SWITCH_J17_13 ((*XBUS_SWITCH) & (1 << 4)) |
| #define XBUS_SWITCH_J17_11 ((*XBUS_SWITCH) & (1 << 5)) |
| #define XBUS_SWITCH_J17_9 ((*XBUS_SWITCH) & (1 << 6)) |
| |
| #define UNCACHEABLE_ADDR (ARMCSR_BASE + 0x108) |
| |
| |
| /* PIC irq control */ |
| #define PIC_LO 0x20 |
| #define PIC_MASK_LO 0x21 |
| #define PIC_HI 0xA0 |
| #define PIC_MASK_HI 0xA1 |
| |
| /* GPIO pins */ |
| #define GPIO_CCLK 0x800 |
| #define GPIO_DSCLK 0x400 |
| #define GPIO_E2CLK 0x200 |
| #define GPIO_IOLOAD 0x100 |
| #define GPIO_RED_LED 0x080 |
| #define GPIO_WDTIMER 0x040 |
| #define GPIO_DATA 0x020 |
| #define GPIO_IOCLK 0x010 |
| #define GPIO_DONE 0x008 |
| #define GPIO_FAN 0x004 |
| #define GPIO_GREEN_LED 0x002 |
| #define GPIO_RESET 0x001 |
| |
| /* CPLD pins */ |
| #define CPLD_DS_ENABLE 8 |
| #define CPLD_7111_DISABLE 4 |
| #define CPLD_UNMUTE 2 |
| #define CPLD_FLASH_WR_ENABLE 1 |
| |
| #ifndef __ASSEMBLY__ |
| extern spinlock_t nw_gpio_lock; |
| extern void nw_gpio_modify_op(unsigned int mask, unsigned int set); |
| extern void nw_gpio_modify_io(unsigned int mask, unsigned int in); |
| extern unsigned int nw_gpio_read(void); |
| extern void nw_cpld_modify(unsigned int mask, unsigned int set); |
| #endif |
| |
| #endif |