ath9k: move ath9k_beacon_config_sta to common-beacon
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/beacon.c b/drivers/net/wireless/ath/ath9k/beacon.c
index 6372671..9333fa1 100644
--- a/drivers/net/wireless/ath/ath9k/beacon.c
+++ b/drivers/net/wireless/ath/ath9k/beacon.c
@@ -505,87 +505,13 @@
ath9k_beacon_init(sc, nexttbtt, intval, false);
}
-/*
- * This sets up the beacon timers according to the timestamp of the last
- * received beacon and the current TSF, configures PCF and DTIM
- * handling, programs the sleep registers so the hardware will wakeup in
- * time to receive beacons, and configures the beacon miss handling so
- * we'll receive a BMISS interrupt when we stop seeing beacons from the AP
- * we've associated with.
- */
-static void ath9k_beacon_config_sta(struct ath_softc *sc,
+static void ath9k_beacon_config_sta(struct ath_hw *ah,
struct ath_beacon_config *conf)
{
- struct ath_hw *ah = sc->sc_ah;
- struct ath_common *common = ath9k_hw_common(ah);
struct ath9k_beacon_state bs;
- int dtim_intval;
- u32 nexttbtt = 0, intval;
- u64 tsf;
- /* No need to configure beacon if we are not associated */
- if (!test_bit(ATH_OP_PRIM_STA_VIF, &common->op_flags)) {
- ath_dbg(common, BEACON,
- "STA is not yet associated..skipping beacon config\n");
+ if (ath9k_cmn_beacon_config_sta(ah, conf, &bs) == -EPERM)
return;
- }
-
- memset(&bs, 0, sizeof(bs));
- intval = conf->beacon_interval;
-
- /*
- * Setup dtim parameters according to
- * last beacon we received (which may be none).
- */
- dtim_intval = intval * conf->dtim_period;
-
- /*
- * Pull nexttbtt forward to reflect the current
- * TSF and calculate dtim state for the result.
- */
- tsf = ath9k_hw_gettsf64(ah);
- nexttbtt = ath9k_get_next_tbtt(sc, tsf, intval);
-
- bs.bs_intval = TU_TO_USEC(intval);
- bs.bs_dtimperiod = conf->dtim_period * bs.bs_intval;
- bs.bs_nexttbtt = nexttbtt;
- bs.bs_nextdtim = nexttbtt;
- if (conf->dtim_period > 1)
- bs.bs_nextdtim = ath9k_get_next_tbtt(sc, tsf, dtim_intval);
-
- /*
- * Calculate the number of consecutive beacons to miss* before taking
- * a BMISS interrupt. The configuration is specified in TU so we only
- * need calculate based on the beacon interval. Note that we clamp the
- * result to at most 15 beacons.
- */
- bs.bs_bmissthreshold = DIV_ROUND_UP(conf->bmiss_timeout, intval);
- if (bs.bs_bmissthreshold > 15)
- bs.bs_bmissthreshold = 15;
- else if (bs.bs_bmissthreshold <= 0)
- bs.bs_bmissthreshold = 1;
-
- /*
- * Calculate sleep duration. The configuration is given in ms.
- * We ensure a multiple of the beacon period is used. Also, if the sleep
- * duration is greater than the DTIM period then it makes senses
- * to make it a multiple of that.
- *
- * XXX fixed at 100ms
- */
-
- bs.bs_sleepduration = TU_TO_USEC(roundup(IEEE80211_MS_TO_TU(100),
- intval));
- if (bs.bs_sleepduration > bs.bs_dtimperiod)
- bs.bs_sleepduration = bs.bs_dtimperiod;
-
- /* TSF out of range threshold fixed at 1 second */
- bs.bs_tsfoor_threshold = ATH9K_TSFOOR_THRESHOLD;
-
- ath_dbg(common, BEACON, "bmiss: %u sleep: %u\n",
- bs.bs_bmissthreshold, bs.bs_sleepduration);
-
- /* Set the computed STA beacon timers */
ath9k_hw_disable_interrupts(ah);
ath9k_hw_set_sta_beacon_timers(ah, &bs);
@@ -777,7 +703,7 @@
ath9k_beacon_config_adhoc(sc, cur_conf);
break;
case NL80211_IFTYPE_STATION:
- ath9k_beacon_config_sta(sc, cur_conf);
+ ath9k_beacon_config_sta(sc->sc_ah, cur_conf);
break;
default:
ath_dbg(common, CONFIG, "Unsupported beaconing mode\n");