net: convert unicast addr list

This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c
index 0cc3c47..6f79409 100644
--- a/drivers/net/ixgbe/ixgbe_common.c
+++ b/drivers/net/ixgbe/ixgbe_common.c
@@ -28,6 +28,8 @@
 #include <linux/pci.h>
 #include <linux/delay.h>
 #include <linux/sched.h>
+#include <linux/list.h>
+#include <linux/netdevice.h>
 
 #include "ixgbe.h"
 #include "ixgbe_common.h"
@@ -1356,15 +1358,14 @@
  *  Drivers using secondary unicast addresses must set user_set_promisc when
  *  manually putting the device into promiscuous mode.
  **/
-s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw, u8 *addr_list,
-                              u32 addr_count, ixgbe_mc_addr_itr next)
+s32 ixgbe_update_uc_addr_list_generic(struct ixgbe_hw *hw,
+				      struct list_head *uc_list)
 {
-	u8 *addr;
 	u32 i;
 	u32 old_promisc_setting = hw->addr_ctrl.overflow_promisc;
 	u32 uc_addr_in_use;
 	u32 fctrl;
-	u32 vmdq;
+	struct netdev_hw_addr *ha;
 
 	/*
 	 * Clear accounting of old secondary address list,
@@ -1382,10 +1383,9 @@
 	}
 
 	/* Add the new addresses */
-	for (i = 0; i < addr_count; i++) {
+	list_for_each_entry(ha, uc_list, list) {
 		hw_dbg(hw, " Adding the secondary addresses:\n");
-		addr = next(hw, &addr_list, &vmdq);
-		ixgbe_add_uc_addr(hw, addr, vmdq);
+		ixgbe_add_uc_addr(hw, ha->addr, 0);
 	}
 
 	if (hw->addr_ctrl.overflow_promisc) {