tpm tis: Do not print timeout messages twice
The tis driver does a tpm_get_timeouts out side of tpm_chip_register,
and tpm_get_timeouts can print a message, resulting in two prints, eg:
tpm tpm0: [Hardware Error]: Adjusting reported timeouts: A 10000->750000us B 10000->2000000us C 10000->750000us D 10000->750000us
Keep track and prevent tpm_get_timeouts from running a second time, and
clarify the purpose of the call in tpm_tis_core to only be connected to
irq testing.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
diff --git a/drivers/char/tpm/tpm-interface.c b/drivers/char/tpm/tpm-interface.c
index ffdae1d..ef0fcdb 100644
--- a/drivers/char/tpm/tpm-interface.c
+++ b/drivers/char/tpm/tpm-interface.c
@@ -501,6 +501,9 @@
unsigned long old_timeout[4];
ssize_t rc;
+ if (chip->flags & TPM_CHIP_FLAG_HAVE_TIMEOUTS)
+ return 0;
+
if (chip->flags & TPM_CHIP_FLAG_TPM2) {
/* Fixed timeouts for TPM2 */
chip->timeout_a = msecs_to_jiffies(TPM2_TIMEOUT_A);
@@ -513,6 +516,8 @@
msecs_to_jiffies(TPM2_DURATION_MEDIUM);
chip->duration[TPM_LONG] =
msecs_to_jiffies(TPM2_DURATION_LONG);
+
+ chip->flags |= TPM_CHIP_FLAG_HAVE_TIMEOUTS;
return 0;
}
@@ -596,6 +601,8 @@
chip->duration_adjusted = true;
dev_info(&chip->dev, "Adjusting TPM timeout parameters.");
}
+
+ chip->flags |= TPM_CHIP_FLAG_HAVE_TIMEOUTS;
return 0;
}
EXPORT_SYMBOL_GPL(tpm_get_timeouts);
diff --git a/drivers/char/tpm/tpm.h b/drivers/char/tpm/tpm.h
index 1864932..21c3dbe 100644
--- a/drivers/char/tpm/tpm.h
+++ b/drivers/char/tpm/tpm.h
@@ -143,6 +143,7 @@
TPM_CHIP_FLAG_TPM2 = BIT(1),
TPM_CHIP_FLAG_IRQ = BIT(2),
TPM_CHIP_FLAG_VIRTUAL = BIT(3),
+ TPM_CHIP_FLAG_HAVE_TIMEOUTS = BIT(4),
};
struct tpm_chip {
diff --git a/drivers/char/tpm/tpm_tis_core.c b/drivers/char/tpm/tpm_tis_core.c
index 2d1e451..7993678 100644
--- a/drivers/char/tpm/tpm_tis_core.c
+++ b/drivers/char/tpm/tpm_tis_core.c
@@ -777,20 +777,20 @@
if (intfcaps & TPM_INTF_DATA_AVAIL_INT)
dev_dbg(dev, "\tData Avail Int Support\n");
- /* Very early on issue a command to the TPM in polling mode to make
- * sure it works. May as well use that command to set the proper
- * timeouts for the driver.
- */
- if (tpm_get_timeouts(chip)) {
- dev_err(dev, "Could not get TPM timeouts and durations\n");
- rc = -ENODEV;
- goto out_err;
- }
-
/* INTERRUPT Setup */
init_waitqueue_head(&priv->read_queue);
init_waitqueue_head(&priv->int_queue);
if (irq != -1) {
+ /* Before doing irq testing issue a command to the TPM in polling mode
+ * to make sure it works. May as well use that command to set the
+ * proper timeouts for the driver.
+ */
+ if (tpm_get_timeouts(chip)) {
+ dev_err(dev, "Could not get TPM timeouts and durations\n");
+ rc = -ENODEV;
+ goto out_err;
+ }
+
if (irq) {
tpm_tis_probe_irq_single(chip, intmask, IRQF_SHARED,
irq);