ath10k: unify tx mode and dispatch
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 87ecc3e..7a21aee 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2522,6 +2522,43 @@
return 0;
}
+static enum ath10k_hw_txrx_mode
+ath10k_tx_h_get_txmode(struct ath10k *ar, struct ieee80211_vif *vif,
+ struct sk_buff *skb)
+{
+ const struct ieee80211_hdr *hdr = (void *)skb->data;
+ __le16 fc = hdr->frame_control;
+
+ if (!vif || vif->type == NL80211_IFTYPE_MONITOR)
+ return ATH10K_HW_TXRX_RAW;
+
+ if (ieee80211_is_mgmt(fc))
+ return ATH10K_HW_TXRX_MGMT;
+
+ /* Workaround:
+ *
+ * NullFunc frames are mostly used to ping if a client or AP are still
+ * reachable and responsive. This implies tx status reports must be
+ * accurate - otherwise either mac80211 or userspace (e.g. hostapd) can
+ * come to a conclusion that the other end disappeared and tear down
+ * BSS connection or it can never disconnect from BSS/client (which is
+ * the case).
+ *
+ * Firmware with HTT older than 3.0 delivers incorrect tx status for
+ * NullFunc frames to driver. However there's a HTT Mgmt Tx command
+ * which seems to deliver correct tx reports for NullFunc frames. The
+ * downside of using it is it ignores client powersave state so it can
+ * end up disconnecting sleeping clients in AP mode. It should fix STA
+ * mode though because AP don't sleep.
+ */
+ if (ar->htt.target_version_major < 3 &&
+ (ieee80211_is_nullfunc(fc) || ieee80211_is_qos_nullfunc(fc)) &&
+ !test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX, ar->fw_features))
+ return ATH10K_HW_TXRX_MGMT;
+
+ return ATH10K_HW_TXRX_NATIVE_WIFI;
+}
+
/* HTT Tx uses Native Wifi tx mode which expects 802.11 frames without QoS
* Control in the header.
*/
@@ -2550,6 +2587,33 @@
hdr->frame_control &= ~__cpu_to_le16(IEEE80211_STYPE_QOS_DATA);
}
+static void ath10k_tx_h_8023(struct sk_buff *skb)
+{
+ struct ieee80211_hdr *hdr;
+ struct rfc1042_hdr *rfc1042;
+ struct ethhdr *eth;
+ size_t hdrlen;
+ u8 da[ETH_ALEN];
+ u8 sa[ETH_ALEN];
+ __be16 type;
+
+ hdr = (void *)skb->data;
+ hdrlen = ieee80211_hdrlen(hdr->frame_control);
+ rfc1042 = (void *)skb->data + hdrlen;
+
+ ether_addr_copy(da, ieee80211_get_DA(hdr));
+ ether_addr_copy(sa, ieee80211_get_SA(hdr));
+ type = rfc1042->snap_type;
+
+ skb_pull(skb, hdrlen + sizeof(*rfc1042));
+ skb_push(skb, sizeof(*eth));
+
+ eth = (void *)skb->data;
+ ether_addr_copy(eth->h_dest, da);
+ ether_addr_copy(eth->h_source, sa);
+ eth->h_proto = type;
+}
+
static void ath10k_tx_h_add_p2p_noa_ie(struct ath10k *ar,
struct ieee80211_vif *vif,
struct sk_buff *skb)
@@ -2586,45 +2650,51 @@
ar->htt.target_version_minor >= 4);
}
-static void ath10k_tx_htt(struct ath10k *ar, struct sk_buff *skb)
+static int ath10k_mac_tx_wmi_mgmt(struct ath10k *ar, struct sk_buff *skb)
{
- struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+ struct sk_buff_head *q = &ar->wmi_mgmt_tx_queue;
int ret = 0;
- if (ar->htt.target_version_major >= 3) {
- /* Since HTT 3.0 there is no separate mgmt tx command */
- ret = ath10k_htt_tx(&ar->htt, skb);
- goto exit;
+ spin_lock_bh(&ar->data_lock);
+
+ if (skb_queue_len(q) == ATH10K_MAX_NUM_MGMT_PENDING) {
+ ath10k_warn(ar, "wmi mgmt tx queue is full\n");
+ ret = -ENOSPC;
+ goto unlock;
}
- if (ieee80211_is_mgmt(hdr->frame_control)) {
+ __skb_queue_tail(q, skb);
+ ieee80211_queue_work(ar->hw, &ar->wmi_mgmt_tx_work);
+
+unlock:
+ spin_unlock_bh(&ar->data_lock);
+
+ return ret;
+}
+
+static void ath10k_mac_tx(struct ath10k *ar, struct sk_buff *skb)
+{
+ struct ath10k_skb_cb *cb = ATH10K_SKB_CB(skb);
+ struct ath10k_htt *htt = &ar->htt;
+ int ret = 0;
+
+ switch (cb->txmode) {
+ case ATH10K_HW_TXRX_RAW:
+ case ATH10K_HW_TXRX_NATIVE_WIFI:
+ case ATH10K_HW_TXRX_ETHERNET:
+ ret = ath10k_htt_tx(htt, skb);
+ break;
+ case ATH10K_HW_TXRX_MGMT:
if (test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX,
- ar->fw_features)) {
- if (skb_queue_len(&ar->wmi_mgmt_tx_queue) >=
- ATH10K_MAX_NUM_MGMT_PENDING) {
- ath10k_warn(ar, "reached WMI management transmit queue limit\n");
- ret = -EBUSY;
- goto exit;
- }
-
- skb_queue_tail(&ar->wmi_mgmt_tx_queue, skb);
- ieee80211_queue_work(ar->hw, &ar->wmi_mgmt_tx_work);
- } else {
- ret = ath10k_htt_mgmt_tx(&ar->htt, skb);
- }
- } else if (!test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX,
- ar->fw_features) &&
- ieee80211_is_nullfunc(hdr->frame_control)) {
- /* FW does not report tx status properly for NullFunc frames
- * unless they are sent through mgmt tx path. mac80211 sends
- * those frames when it detects link/beacon loss and depends
- * on the tx status to be correct. */
- ret = ath10k_htt_mgmt_tx(&ar->htt, skb);
- } else {
- ret = ath10k_htt_tx(&ar->htt, skb);
+ ar->fw_features))
+ ret = ath10k_mac_tx_wmi_mgmt(ar, skb);
+ else if (ar->htt.target_version_major >= 3)
+ ret = ath10k_htt_tx(htt, skb);
+ else
+ ret = ath10k_htt_mgmt_tx(htt, skb);
+ break;
}
-exit:
if (ret) {
ath10k_warn(ar, "failed to transmit packet, dropping: %d\n",
ret);
@@ -2697,7 +2767,7 @@
ar->offchan_tx_skb = skb;
spin_unlock_bh(&ar->data_lock);
- ath10k_tx_htt(ar, skb);
+ ath10k_mac_tx(ar, skb);
ret = wait_for_completion_timeout(&ar->offchan_tx_completed,
3 * HZ);
@@ -2922,6 +2992,7 @@
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct ieee80211_vif *vif = info->control.vif;
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+ __le16 fc = hdr->frame_control;
/* We should disable CCK RATE due to P2P */
if (info->flags & IEEE80211_TX_CTL_NO_CCK_RATE)
@@ -2931,12 +3002,26 @@
ATH10K_SKB_CB(skb)->htt.freq = 0;
ATH10K_SKB_CB(skb)->htt.tid = ath10k_tx_h_get_tid(hdr);
ATH10K_SKB_CB(skb)->vdev_id = ath10k_tx_h_get_vdev_id(ar, vif);
+ ATH10K_SKB_CB(skb)->txmode = ath10k_tx_h_get_txmode(ar, vif, skb);
+ ATH10K_SKB_CB(skb)->is_protected = ieee80211_has_protected(fc);
- /* it makes no sense to process injected frames like that */
- if (vif && vif->type != NL80211_IFTYPE_MONITOR) {
+ switch (ATH10K_SKB_CB(skb)->txmode) {
+ case ATH10K_HW_TXRX_MGMT:
+ case ATH10K_HW_TXRX_NATIVE_WIFI:
ath10k_tx_h_nwifi(hw, skb);
ath10k_tx_h_add_p2p_noa_ie(ar, vif, skb);
ath10k_tx_h_seq_no(vif, skb);
+ break;
+ case ATH10K_HW_TXRX_ETHERNET:
+ ath10k_tx_h_8023(skb);
+ break;
+ case ATH10K_HW_TXRX_RAW:
+ /* FIXME: Packet injection isn't implemented. It should be
+ * doable with firmware 10.2 on qca988x.
+ */
+ WARN_ON_ONCE(1);
+ ieee80211_free_txskb(hw, skb);
+ return;
}
if (info->flags & IEEE80211_TX_CTL_TX_OFFCHAN) {
@@ -2958,7 +3043,7 @@
}
}
- ath10k_tx_htt(ar, skb);
+ ath10k_mac_tx(ar, skb);
}
/* Must not be called with conf_mutex held as workers can use that also. */