rt2x00: configure different txdesc parameters for non HT channel
This is needed when we are concted to non 11n AP.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h
index 471f87ca..8de9bfc 100644
--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -692,6 +692,7 @@
*/
CONFIG_CHANNEL_HT40,
CONFIG_POWERSAVING,
+ CONFIG_HT_DISABLED,
/*
* Mark we currently are sequentially reading TX_STA_FIFO register
diff --git a/drivers/net/wireless/rt2x00/rt2x00config.c b/drivers/net/wireless/rt2x00/rt2x00config.c
index 293676b..e7361d9 100644
--- a/drivers/net/wireless/rt2x00/rt2x00config.c
+++ b/drivers/net/wireless/rt2x00/rt2x00config.c
@@ -217,6 +217,11 @@
libconf.conf = conf;
if (ieee80211_flags & IEEE80211_CONF_CHANGE_CHANNEL) {
+ if (!conf_is_ht(conf))
+ set_bit(CONFIG_HT_DISABLED, &rt2x00dev->flags);
+ else
+ clear_bit(CONFIG_HT_DISABLED, &rt2x00dev->flags);
+
if (conf_is_ht40(conf)) {
set_bit(CONFIG_CHANNEL_HT40, &rt2x00dev->flags);
hw_value = rt2x00ht_center_channel(rt2x00dev, conf);
diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c
index 9b1b2b7..acd0133 100644
--- a/drivers/net/wireless/rt2x00/rt2x00queue.c
+++ b/drivers/net/wireless/rt2x00/rt2x00queue.c
@@ -320,14 +320,6 @@
txdesc->u.ht.wcid = sta_priv->wcid;
}
- txdesc->u.ht.ba_size = 7; /* FIXME: What value is needed? */
-
- /*
- * Only one STBC stream is supported for now.
- */
- if (tx_info->flags & IEEE80211_TX_CTL_STBC)
- txdesc->u.ht.stbc = 1;
-
/*
* If IEEE80211_TX_RC_MCS is set txrate->idx just contains the
* mcs rate to be used
@@ -351,6 +343,24 @@
txdesc->u.ht.mcs |= 0x08;
}
+ if (test_bit(CONFIG_HT_DISABLED, &rt2x00dev->flags)) {
+ if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT))
+ txdesc->u.ht.txop = TXOP_SIFS;
+ else
+ txdesc->u.ht.txop = TXOP_BACKOFF;
+
+ /* Left zero on all other settings. */
+ return;
+ }
+
+ txdesc->u.ht.ba_size = 7; /* FIXME: What value is needed? */
+
+ /*
+ * Only one STBC stream is supported for now.
+ */
+ if (tx_info->flags & IEEE80211_TX_CTL_STBC)
+ txdesc->u.ht.stbc = 1;
+
/*
* This frame is eligible for an AMPDU, however, don't aggregate
* frames that are intended to probe a specific tx rate.