[Blackfin] arch: Apply Bluetechnix vendor patch
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 369050d..d1590c7 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -323,7 +323,7 @@
range 1 64
default "22" if BFIN533_EZKIT
default "45" if BFIN533_STAMP
- default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if BFIN537_BLUETECHNIX_CM
default "20" if BFIN561_BLUETECHNIX_CM
@@ -360,7 +360,7 @@
range 1 15
default 5 if BFIN533_EZKIT
default 5 if BFIN533_STAMP
- default 4 if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
+ default 4 if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
default 5 if BFIN533_BLUETECHNIX_CM
default 4 if BFIN537_BLUETECHNIX_CM
default 4 if BFIN561_BLUETECHNIX_CM
@@ -449,10 +449,11 @@
default 128 if BFIN533_STAMP
default 64 if PNAV10
default 32 if H8606_HVSISTEMAS
+ default 64 if BFIN548_BLUETECHNIX_CM
choice
prompt "DDR SDRAM Chip Type"
- depends on BFIN548_EZKIT
+ depends on (BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
default MEM_MT46V32M16_5B
config MEM_MT46V32M16_6T
diff --git a/arch/blackfin/mach-bf548/boards/Kconfig b/arch/blackfin/mach-bf548/boards/Kconfig
index 0571290..d38e526 100644
--- a/arch/blackfin/mach-bf548/boards/Kconfig
+++ b/arch/blackfin/mach-bf548/boards/Kconfig
@@ -8,5 +8,11 @@
bool "BF548-EZKIT"
help
BFIN548-EZKIT board support.
+
+config BFIN548_BLUETECHNIX_CM
+ bool "Bluetechnix CM-BF548"
+ depends on (BF548)
+ help
+ CM-BF548 support for DEV-Board.
endchoice
diff --git a/arch/blackfin/mach-bf548/boards/Makefile b/arch/blackfin/mach-bf548/boards/Makefile
index a444cc7..eed161d 100644
--- a/arch/blackfin/mach-bf548/boards/Makefile
+++ b/arch/blackfin/mach-bf548/boards/Makefile
@@ -3,3 +3,4 @@
#
obj-$(CONFIG_BFIN548_EZKIT) += ezkit.o led.o
+obj-$(CONFIG_BFIN548_BLUETECHNIX_CM) += cm_bf548.o
diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
new file mode 100644
index 0000000..1aa3c1b
--- /dev/null
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -0,0 +1,620 @@
+/*
+ * File: arch/blackfin/mach-bf548/boards/cm_bf548.c
+ * Based on: arch/blackfin/mach-bf537/boards/ezkit.c
+ * Author: Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/cplb.h>
+#include <asm/dma.h>
+#include <asm/gpio.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/mach/bf54x_keys.h>
+#include <linux/input.h>
+#include <linux/spi/ad7877.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM-BF548";
+
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+
+#include <asm/mach/bf54x-lq043.h>
+
+static struct bfin_bf54xfb_mach_info bf54x_lq043_data = {
+ .width = 480,
+ .height = 272,
+ .xres = {480, 480, 480},
+ .yres = {272, 272, 272},
+ .bpp = {24, 24, 24},
+ .disp = GPIO_PE3,
+};
+
+static struct resource bf54x_lq043_resources[] = {
+ {
+ .start = IRQ_EPPI0_ERR,
+ .end = IRQ_EPPI0_ERR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf54x_lq043_device = {
+ .name = "bf54x-lq043",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf54x_lq043_resources),
+ .resource = bf54x_lq043_resources,
+ .dev = {
+ .platform_data = &bf54x_lq043_data,
+ },
+};
+#endif
+
+#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+static unsigned int bf548_keymap[] = {
+ KEYVAL(0, 0, KEY_ENTER),
+ KEYVAL(0, 1, KEY_HELP),
+ KEYVAL(0, 2, KEY_0),
+ KEYVAL(0, 3, KEY_BACKSPACE),
+ KEYVAL(1, 0, KEY_TAB),
+ KEYVAL(1, 1, KEY_9),
+ KEYVAL(1, 2, KEY_8),
+ KEYVAL(1, 3, KEY_7),
+ KEYVAL(2, 0, KEY_DOWN),
+ KEYVAL(2, 1, KEY_6),
+ KEYVAL(2, 2, KEY_5),
+ KEYVAL(2, 3, KEY_4),
+ KEYVAL(3, 0, KEY_UP),
+ KEYVAL(3, 1, KEY_3),
+ KEYVAL(3, 2, KEY_2),
+ KEYVAL(3, 3, KEY_1),
+};
+
+static struct bfin_kpad_platform_data bf54x_kpad_data = {
+ .rows = 4,
+ .cols = 4,
+ .keymap = bf548_keymap,
+ .keymapsize = ARRAY_SIZE(bf548_keymap),
+ .repeat = 0,
+ .debounce_time = 5000, /* ns (5ms) */
+ .coldrive_time = 1000, /* ns (1ms) */
+ .keyup_test_interval = 50, /* ms (50ms) */
+};
+
+static struct resource bf54x_kpad_resources[] = {
+ {
+ .start = IRQ_KEY,
+ .end = IRQ_KEY,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf54x_kpad_device = {
+ .name = "bf54x-keys",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bf54x_kpad_resources),
+ .resource = bf54x_kpad_resources,
+ .dev = {
+ .platform_data = &bf54x_kpad_data,
+ },
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART2
+ {
+ .start = 0xFFC02100,
+ .end = 0xFFC021FF,
+ .flags = IORESOURCE_MEM,
+ },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART3
+ {
+ .start = 0xFFC03100,
+ .end = 0xFFC031FF,
+ },
+#endif
+};
+
+static struct platform_device bfin_uart_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart_resources),
+ .resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+static struct resource smsc911x_resources[] = {
+ {
+ .name = "smsc911x-memory",
+ .start = 0x24000000,
+ .end = 0x24000000 + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_PE6,
+ .end = IRQ_PE6,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+ },
+};
+static struct platform_device smsc911x_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+ [0] = {
+ .start = 0xFFC03C00,
+ .end = 0xFFC040FF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* general IRQ */
+ .start = IRQ_USB_INT0,
+ .end = IRQ_USB_INT0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+ [2] = { /* DMA IRQ */
+ .start = IRQ_USB_DMA,
+ .end = IRQ_USB_DMA,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+ .mode = MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+ .mode = MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+ .mode = MUSB_PERIPHERAL,
+#endif
+ .multipoint = 0,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+ .name = "musb_hdrc",
+ .id = 0,
+ .dev = {
+ .dma_mask = &musb_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = &musb_plat,
+ },
+ .num_resources = ARRAY_SIZE(musb_resources),
+ .resource = musb_resources,
+};
+#endif
+
+#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+static struct resource bfin_atapi_resources[] = {
+ {
+ .start = 0xFFC03800,
+ .end = 0xFFC0386F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_ATAPI_ERR,
+ .end = IRQ_ATAPI_ERR,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_atapi_device = {
+ .name = "pata-bf54x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_atapi_resources),
+ .resource = bfin_atapi_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+ {
+ .name = "Linux Kernel",
+ .offset = 0,
+ .size = 4 * SIZE_1M,
+ },
+ {
+ .name = "File System",
+ .offset = 4 * SIZE_1M,
+ .size = (256 - 4) * SIZE_1M,
+ },
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+ .page_size = NFC_PG_SIZE_256,
+ .data_width = NFC_NWIDTH_8,
+ .partitions = partition_info,
+ .nr_partitions = ARRAY_SIZE(partition_info),
+ .rd_dly = 3,
+ .wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+ {
+ .start = 0xFFC03B00,
+ .end = 0xFFC03B4F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = CH_NFC,
+ .end = CH_NFC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bf5xx_nand_device = {
+ .name = "bf5xx-nand",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+ .resource = bf5xx_nand_resources,
+ .dev = {
+ .platform_data = &bf5xx_nand_platform,
+ },
+};
+#endif
+
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+static struct platform_device bf54x_sdh_device = {
+ .name = "bfin-sdh",
+ .id = 0,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+/* SPI flash chip (m25p16) */
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel",
+ .size = 0x1c0000,
+ .offset = 0x40000
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p16",
+};
+
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+ .cs_change_per_word = 0,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+ .cs_change_per_word = 0,
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+ .model = 7877,
+ .vref_delay_usecs = 50, /* internal, no capacitor */
+ .x_plate_ohms = 419,
+ .y_plate_ohms = 486,
+ .pressure_max = 1000,
+ .pressure_min = 0,
+ .stopacq_polarity = 1,
+ .first_conversion_delay = 3,
+ .acquisition_time = 1,
+ .averaging = 1,
+ .pen_down_acc_interval = 1,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bf54x_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+ || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* SPI_SSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+{
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PJ11,
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_ad7877_chip_info,
+},
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &spidev_chip_info,
+ },
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI0,
+ .end = CH_SPI0,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+/* SPI (1) */
+static struct resource bfin_spi1_resource[] = {
+ [0] = {
+ .start = SPI1_REGBASE,
+ .end = SPI1_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI1,
+ .end = CH_SPI1,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bf54x_spi_master0 = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bf54x_spi_master_info0, /* Passed to driver */
+ },
+};
+
+static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
+};
+
+static struct platform_device bf54x_spi_master1 = {
+ .name = "bfin-spi",
+ .id = 1, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi1_resource),
+ .resource = bfin_spi1_resource,
+ .dev = {
+ .platform_data = &bf54x_spi_master_info1, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI0,
+ .end = IRQ_TWI0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi0_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+
+#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
+static struct resource bfin_twi1_resource[] = {
+ [0] = {
+ .start = TWI1_REGBASE,
+ .end = TWI1_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI1,
+ .end = IRQ_TWI1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi1_device = {
+ .name = "i2c-bfin-twi",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_twi1_resource),
+ .resource = bfin_twi1_resource,
+};
+#endif
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#include <linux/gpio_keys.h>
+
+static struct gpio_keys_button bfin_gpio_keys_table[] = {
+ {BTN_0, GPIO_PH7, 1, "gpio-keys: BTN0"},
+};
+
+static struct gpio_keys_platform_data bfin_gpio_keys_data = {
+ .buttons = bfin_gpio_keys_table,
+ .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
+};
+
+static struct platform_device bfin_device_gpiokeys = {
+ .name = "gpio-keys",
+ .dev = {
+ .platform_data = &bfin_gpio_keys_data,
+ },
+};
+#endif
+
+static struct platform_device *cm_bf548_devices[] __initdata = {
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+ &bfin_uart_device,
+#endif
+
+#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
+ &bf54x_lq043_device,
+#endif
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+ &smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+ &musb_device,
+#endif
+
+#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
+ &bfin_atapi_device,
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+ &bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+ &bf54x_sdh_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bf54x_spi_master0,
+ &bf54x_spi_master1,
+#endif
+
+#if defined(CONFIG_KEYBOARD_BFIN) || defined(CONFIG_KEYBOARD_BFIN_MODULE)
+ &bf54x_kpad_device,
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+/* &i2c_bfin_twi0_device, */
+#if !defined(CONFIG_BF542)
+ &i2c_bfin_twi1_device,
+#endif
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+ &bfin_device_gpiokeys,
+#endif
+};
+
+static int __init cm_bf548_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ platform_add_devices(cm_bf548_devices, ARRAY_SIZE(cm_bf548_devices));
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bf54x_spi_board_info,
+ ARRAY_SIZE(bf54x_spi_board_info));
+#endif
+
+ return 0;
+}
+
+arch_initcall(cm_bf548_init);