Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (46 commits)
[media] rc: call input_sync after scancode reports
[media] imon: allow either proto on unknown 0xffdc
[media] imon: auto-config ffdc 7e device
[media] saa7134: fix raw IR timeout value
[media] rc: fix ghost keypresses with certain hw
[media] [staging] lirc_serial: allocate irq at init time
[media] lirc_zilog: fix spinning rx thread
[media] keymaps: fix table for pinnacle pctv hd devices
[media] ite-cir: 8709 needs to use pnp resource 2
[media] V4L: mx1-camera: fix uninitialized variable
[media] omap_vout: Added check in reqbuf & mmap for buf_size allocation
[media] OMAP_VOUT: Change hardcoded device node number to -1
[media] OMAP_VOUTLIB: Fix wrong resizer calculation
[media] uvcvideo: Disable the queue when failing to start
[media] uvcvideo: Remove buffers from the queues when freeing
[media] uvcvideo: Ignore entities for terminals with no supported format
[media] v4l: Don't access media entity after is has been destroyed
[media] media: omap3isp: fix a potential NULL deref
[media] media: vb2: fix allocation failure check
[media] media: vb2: reset queued_count value during queue reinitialization
...
Fix up trivial conflict in MAINTAINERS as per Mauro
diff --git a/MAINTAINERS b/MAINTAINERS
index ae563fa..584bdb2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6733,6 +6733,7 @@
VIDEOBUF2 FRAMEWORK
M: Pawel Osciak <pawel@osciak.com>
M: Marek Szyprowski <m.szyprowski@samsung.com>
+M: Kyungmin Park <kyungmin.park@samsung.com>
L: linux-media@vger.kernel.org
S: Maintained
F: drivers/media/video/videobuf2-*
diff --git a/drivers/media/rc/fintek-cir.c b/drivers/media/rc/fintek-cir.c
index 8fa539d..7f7079b 100644
--- a/drivers/media/rc/fintek-cir.c
+++ b/drivers/media/rc/fintek-cir.c
@@ -597,12 +597,17 @@
static int fintek_suspend(struct pnp_dev *pdev, pm_message_t state)
{
struct fintek_dev *fintek = pnp_get_drvdata(pdev);
+ unsigned long flags;
fit_dbg("%s called", __func__);
+ spin_lock_irqsave(&fintek->fintek_lock, flags);
+
/* disable all CIR interrupts */
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
+ spin_unlock_irqrestore(&fintek->fintek_lock, flags);
+
fintek_config_mode_enable(fintek);
/* disable cir logical dev */
diff --git a/drivers/media/rc/imon.c b/drivers/media/rc/imon.c
index 3f3c707..6bc35ee 100644
--- a/drivers/media/rc/imon.c
+++ b/drivers/media/rc/imon.c
@@ -307,6 +307,14 @@
/* 0xffdc iMON MCE VFD */
{ 0x00010000ffffffeell, KEY_VOLUMEUP },
{ 0x01000000ffffffeell, KEY_VOLUMEDOWN },
+ { 0x00000001ffffffeell, KEY_MUTE },
+ { 0x0000000fffffffeell, KEY_MEDIA },
+ { 0x00000012ffffffeell, KEY_UP },
+ { 0x00000013ffffffeell, KEY_DOWN },
+ { 0x00000014ffffffeell, KEY_LEFT },
+ { 0x00000015ffffffeell, KEY_RIGHT },
+ { 0x00000016ffffffeell, KEY_ENTER },
+ { 0x00000017ffffffeell, KEY_ESC },
/* iMON Knob values */
{ 0x000100ffffffffeell, KEY_VOLUMEUP },
{ 0x010000ffffffffeell, KEY_VOLUMEDOWN },
@@ -1582,16 +1590,16 @@
/* Only panel type events left to process now */
spin_lock_irqsave(&ictx->kc_lock, flags);
+ do_gettimeofday(&t);
/* KEY_MUTE repeats from knob need to be suppressed */
if (ictx->kc == KEY_MUTE && ictx->kc == ictx->last_keycode) {
- do_gettimeofday(&t);
msec = tv2int(&t, &prev_time);
- prev_time = t;
if (msec < ictx->idev->rep[REP_DELAY]) {
spin_unlock_irqrestore(&ictx->kc_lock, flags);
return;
}
}
+ prev_time = t;
kc = ictx->kc;
spin_unlock_irqrestore(&ictx->kc_lock, flags);
@@ -1603,7 +1611,9 @@
input_report_key(ictx->idev, kc, 0);
input_sync(ictx->idev);
+ spin_lock_irqsave(&ictx->kc_lock, flags);
ictx->last_keycode = kc;
+ spin_unlock_irqrestore(&ictx->kc_lock, flags);
return;
@@ -1740,6 +1750,8 @@
detected_display_type = IMON_DISPLAY_TYPE_VFD;
break;
/* iMON VFD, MCE IR */
+ case 0x46:
+ case 0x7e:
case 0x9e:
dev_info(ictx->dev, "0xffdc iMON VFD, MCE IR");
detected_display_type = IMON_DISPLAY_TYPE_VFD;
@@ -1755,6 +1767,9 @@
dev_info(ictx->dev, "Unknown 0xffdc device, "
"defaulting to VFD and iMON IR");
detected_display_type = IMON_DISPLAY_TYPE_VFD;
+ /* We don't know which one it is, allow user to set the
+ * RC6 one from userspace if OTHER wasn't correct. */
+ allowed_protos |= RC_TYPE_RC6;
break;
}
diff --git a/drivers/media/rc/ir-raw.c b/drivers/media/rc/ir-raw.c
index 11c19d8..423ed45 100644
--- a/drivers/media/rc/ir-raw.c
+++ b/drivers/media/rc/ir-raw.c
@@ -114,18 +114,20 @@
s64 delta; /* ns */
DEFINE_IR_RAW_EVENT(ev);
int rc = 0;
+ int delay;
if (!dev->raw)
return -EINVAL;
now = ktime_get();
delta = ktime_to_ns(ktime_sub(now, dev->raw->last_event));
+ delay = MS_TO_NS(dev->input_dev->rep[REP_DELAY]);
/* Check for a long duration since last event or if we're
* being called for the first time, note that delta can't
* possibly be negative.
*/
- if (delta > IR_MAX_DURATION || !dev->raw->last_type)
+ if (delta > delay || !dev->raw->last_type)
type |= IR_START_EVENT;
else
ev.duration = delta;
diff --git a/drivers/media/rc/ite-cir.c b/drivers/media/rc/ite-cir.c
index e716b93..ecd3d02 100644
--- a/drivers/media/rc/ite-cir.c
+++ b/drivers/media/rc/ite-cir.c
@@ -1347,6 +1347,7 @@
{ /* 0: ITE8704 */
.model = "ITE8704 CIR transceiver",
.io_region_size = IT87_IOREG_LENGTH,
+ .io_rsrc_no = 0,
.hw_tx_capable = true,
.sample_period = (u32) (1000000000ULL / 115200),
.tx_carrier_freq = 38000,
@@ -1371,6 +1372,7 @@
{ /* 1: ITE8713 */
.model = "ITE8713 CIR transceiver",
.io_region_size = IT87_IOREG_LENGTH,
+ .io_rsrc_no = 0,
.hw_tx_capable = true,
.sample_period = (u32) (1000000000ULL / 115200),
.tx_carrier_freq = 38000,
@@ -1395,6 +1397,7 @@
{ /* 2: ITE8708 */
.model = "ITE8708 CIR transceiver",
.io_region_size = IT8708_IOREG_LENGTH,
+ .io_rsrc_no = 0,
.hw_tx_capable = true,
.sample_period = (u32) (1000000000ULL / 115200),
.tx_carrier_freq = 38000,
@@ -1420,6 +1423,7 @@
{ /* 3: ITE8709 */
.model = "ITE8709 CIR transceiver",
.io_region_size = IT8709_IOREG_LENGTH,
+ .io_rsrc_no = 2,
.hw_tx_capable = true,
.sample_period = (u32) (1000000000ULL / 115200),
.tx_carrier_freq = 38000,
@@ -1461,6 +1465,7 @@
struct rc_dev *rdev = NULL;
int ret = -ENOMEM;
int model_no;
+ int io_rsrc_no;
ite_dbg("%s called", __func__);
@@ -1490,10 +1495,11 @@
/* get the description for the device */
dev_desc = &ite_dev_descs[model_no];
+ io_rsrc_no = dev_desc->io_rsrc_no;
/* validate pnp resources */
- if (!pnp_port_valid(pdev, 0) ||
- pnp_port_len(pdev, 0) != dev_desc->io_region_size) {
+ if (!pnp_port_valid(pdev, io_rsrc_no) ||
+ pnp_port_len(pdev, io_rsrc_no) != dev_desc->io_region_size) {
dev_err(&pdev->dev, "IR PNP Port not valid!\n");
goto failure;
}
@@ -1504,7 +1510,7 @@
}
/* store resource values */
- itdev->cir_addr = pnp_port_start(pdev, 0);
+ itdev->cir_addr = pnp_port_start(pdev, io_rsrc_no);
itdev->cir_irq = pnp_irq(pdev, 0);
/* initialize spinlocks */
diff --git a/drivers/media/rc/ite-cir.h b/drivers/media/rc/ite-cir.h
index 16a19f5..aa899a0 100644
--- a/drivers/media/rc/ite-cir.h
+++ b/drivers/media/rc/ite-cir.h
@@ -57,6 +57,9 @@
/* size of the I/O region */
int io_region_size;
+ /* IR pnp I/O resource number */
+ int io_rsrc_no;
+
/* true if the hardware supports transmission */
bool hw_tx_capable;
diff --git a/drivers/media/rc/keymaps/rc-pinnacle-pctv-hd.c b/drivers/media/rc/keymaps/rc-pinnacle-pctv-hd.c
index bb10ffe..8d558ae 100644
--- a/drivers/media/rc/keymaps/rc-pinnacle-pctv-hd.c
+++ b/drivers/media/rc/keymaps/rc-pinnacle-pctv-hd.c
@@ -15,43 +15,39 @@
/* Pinnacle PCTV HD 800i mini remote */
static struct rc_map_table pinnacle_pctv_hd[] = {
-
- { 0x0f, KEY_1 },
- { 0x15, KEY_2 },
- { 0x10, KEY_3 },
- { 0x18, KEY_4 },
- { 0x1b, KEY_5 },
- { 0x1e, KEY_6 },
- { 0x11, KEY_7 },
- { 0x21, KEY_8 },
- { 0x12, KEY_9 },
- { 0x27, KEY_0 },
-
- { 0x24, KEY_ZOOM },
- { 0x2a, KEY_SUBTITLE },
-
- { 0x00, KEY_MUTE },
- { 0x01, KEY_ENTER }, /* Pinnacle Logo */
- { 0x39, KEY_POWER },
-
- { 0x03, KEY_VOLUMEUP },
- { 0x09, KEY_VOLUMEDOWN },
- { 0x06, KEY_CHANNELUP },
- { 0x0c, KEY_CHANNELDOWN },
-
- { 0x2d, KEY_REWIND },
- { 0x30, KEY_PLAYPAUSE },
- { 0x33, KEY_FASTFORWARD },
- { 0x3c, KEY_STOP },
- { 0x36, KEY_RECORD },
- { 0x3f, KEY_EPG }, /* Labeled "?" */
+ /* Key codes for the tiny Pinnacle remote*/
+ { 0x0700, KEY_MUTE },
+ { 0x0701, KEY_MENU }, /* Pinnacle logo */
+ { 0x0739, KEY_POWER },
+ { 0x0703, KEY_VOLUMEUP },
+ { 0x0709, KEY_VOLUMEDOWN },
+ { 0x0706, KEY_CHANNELUP },
+ { 0x070c, KEY_CHANNELDOWN },
+ { 0x070f, KEY_1 },
+ { 0x0715, KEY_2 },
+ { 0x0710, KEY_3 },
+ { 0x0718, KEY_4 },
+ { 0x071b, KEY_5 },
+ { 0x071e, KEY_6 },
+ { 0x0711, KEY_7 },
+ { 0x0721, KEY_8 },
+ { 0x0712, KEY_9 },
+ { 0x0727, KEY_0 },
+ { 0x0724, KEY_ZOOM }, /* 'Square' key */
+ { 0x072a, KEY_SUBTITLE }, /* 'T' key */
+ { 0x072d, KEY_REWIND },
+ { 0x0730, KEY_PLAYPAUSE },
+ { 0x0733, KEY_FASTFORWARD },
+ { 0x0736, KEY_RECORD },
+ { 0x073c, KEY_STOP },
+ { 0x073f, KEY_HELP }, /* '?' key */
};
static struct rc_map_list pinnacle_pctv_hd_map = {
.map = {
.scan = pinnacle_pctv_hd,
.size = ARRAY_SIZE(pinnacle_pctv_hd),
- .rc_type = RC_TYPE_UNKNOWN, /* Legacy IR type */
+ .rc_type = RC_TYPE_RC5,
.name = RC_MAP_PINNACLE_PCTV_HD,
}
};
diff --git a/drivers/media/rc/lirc_dev.c b/drivers/media/rc/lirc_dev.c
index fd237ab..27997a9 100644
--- a/drivers/media/rc/lirc_dev.c
+++ b/drivers/media/rc/lirc_dev.c
@@ -55,6 +55,8 @@
struct lirc_buffer *buf;
unsigned int chunk_size;
+ struct cdev *cdev;
+
struct task_struct *task;
long jiffies_to_wait;
};
@@ -62,7 +64,6 @@
static DEFINE_MUTEX(lirc_dev_lock);
static struct irctl *irctls[MAX_IRCTL_DEVICES];
-static struct cdev cdevs[MAX_IRCTL_DEVICES];
/* Only used for sysfs but defined to void otherwise */
static struct class *lirc_class;
@@ -167,9 +168,13 @@
static int lirc_cdev_add(struct irctl *ir)
{
- int retval;
+ int retval = -ENOMEM;
struct lirc_driver *d = &ir->d;
- struct cdev *cdev = &cdevs[d->minor];
+ struct cdev *cdev;
+
+ cdev = kzalloc(sizeof(*cdev), GFP_KERNEL);
+ if (!cdev)
+ goto err_out;
if (d->fops) {
cdev_init(cdev, d->fops);
@@ -180,12 +185,20 @@
}
retval = kobject_set_name(&cdev->kobj, "lirc%d", d->minor);
if (retval)
- return retval;
+ goto err_out;
retval = cdev_add(cdev, MKDEV(MAJOR(lirc_base_dev), d->minor), 1);
- if (retval)
+ if (retval) {
kobject_put(&cdev->kobj);
+ goto err_out;
+ }
+ ir->cdev = cdev;
+
+ return 0;
+
+err_out:
+ kfree(cdev);
return retval;
}
@@ -214,7 +227,7 @@
if (MAX_IRCTL_DEVICES <= d->minor) {
dev_err(d->dev, "lirc_dev: lirc_register_driver: "
"\"minor\" must be between 0 and %d (%d)!\n",
- MAX_IRCTL_DEVICES-1, d->minor);
+ MAX_IRCTL_DEVICES - 1, d->minor);
err = -EBADRQC;
goto out;
}
@@ -369,7 +382,7 @@
if (minor < 0 || minor >= MAX_IRCTL_DEVICES) {
printk(KERN_ERR "lirc_dev: %s: minor (%d) must be between "
- "0 and %d!\n", __func__, minor, MAX_IRCTL_DEVICES-1);
+ "0 and %d!\n", __func__, minor, MAX_IRCTL_DEVICES - 1);
return -EBADRQC;
}
@@ -380,7 +393,7 @@
return -ENOENT;
}
- cdev = &cdevs[minor];
+ cdev = ir->cdev;
mutex_lock(&lirc_dev_lock);
@@ -410,6 +423,7 @@
} else {
lirc_irctl_cleanup(ir);
cdev_del(cdev);
+ kfree(cdev);
kfree(ir);
irctls[minor] = NULL;
}
@@ -453,7 +467,7 @@
goto error;
}
- cdev = &cdevs[iminor(inode)];
+ cdev = ir->cdev;
if (try_module_get(cdev->owner)) {
ir->open++;
retval = ir->d.set_use_inc(ir->d.data);
@@ -484,13 +498,15 @@
int lirc_dev_fop_close(struct inode *inode, struct file *file)
{
struct irctl *ir = irctls[iminor(inode)];
- struct cdev *cdev = &cdevs[iminor(inode)];
+ struct cdev *cdev;
if (!ir) {
printk(KERN_ERR "%s: called with invalid irctl\n", __func__);
return -EINVAL;
}
+ cdev = ir->cdev;
+
dev_dbg(ir->d.dev, LOGHEAD "close called\n", ir->d.name, ir->d.minor);
WARN_ON(mutex_lock_killable(&lirc_dev_lock));
@@ -503,6 +519,7 @@
lirc_irctl_cleanup(ir);
cdev_del(cdev);
irctls[ir->d.minor] = NULL;
+ kfree(cdev);
kfree(ir);
}
diff --git a/drivers/media/rc/mceusb.c b/drivers/media/rc/mceusb.c
index ad927fc..06dfe09 100644
--- a/drivers/media/rc/mceusb.c
+++ b/drivers/media/rc/mceusb.c
@@ -108,6 +108,12 @@
static int debug;
#endif
+#define mce_dbg(dev, fmt, ...) \
+ do { \
+ if (debug) \
+ dev_info(dev, fmt, ## __VA_ARGS__); \
+ } while (0)
+
/* general constants */
#define SEND_FLAG_IN_PROGRESS 1
#define SEND_FLAG_COMPLETE 2
@@ -246,6 +252,9 @@
.driver_info = MCE_GEN2_TX_INV },
/* SMK eHome Infrared Transceiver */
{ USB_DEVICE(VENDOR_SMK, 0x0338) },
+ /* SMK/I-O Data GV-MC7/RCKIT Receiver */
+ { USB_DEVICE(VENDOR_SMK, 0x0353),
+ .driver_info = MCE_GEN2_NO_TX },
/* Tatung eHome Infrared Transceiver */
{ USB_DEVICE(VENDOR_TATUNG, 0x9150) },
/* Shuttle eHome Infrared Transceiver */
@@ -606,12 +615,15 @@
if (ir) {
len = urb->actual_length;
- dev_dbg(ir->dev, "callback called (status=%d len=%d)\n",
+ mce_dbg(ir->dev, "callback called (status=%d len=%d)\n",
urb->status, len);
mceusb_dev_printdata(ir, urb->transfer_buffer, 0, len, true);
}
+ /* the transfer buffer and urb were allocated in mce_request_packet */
+ kfree(urb->transfer_buffer);
+ usb_free_urb(urb);
}
/* request incoming or send outgoing usb packet - used to initialize remote */
@@ -655,17 +667,17 @@
return;
}
- dev_dbg(dev, "receive request called (size=%#x)\n", size);
+ mce_dbg(dev, "receive request called (size=%#x)\n", size);
async_urb->transfer_buffer_length = size;
async_urb->dev = ir->usbdev;
res = usb_submit_urb(async_urb, GFP_ATOMIC);
if (res) {
- dev_dbg(dev, "receive request FAILED! (res=%d)\n", res);
+ mce_dbg(dev, "receive request FAILED! (res=%d)\n", res);
return;
}
- dev_dbg(dev, "receive request complete (res=%d)\n", res);
+ mce_dbg(dev, "receive request complete (res=%d)\n", res);
}
static void mce_async_out(struct mceusb_dev *ir, unsigned char *data, int size)
@@ -673,9 +685,9 @@
mce_request_packet(ir, data, size, MCEUSB_TX);
}
-static void mce_sync_in(struct mceusb_dev *ir, unsigned char *data, int size)
+static void mce_flush_rx_buffer(struct mceusb_dev *ir, int size)
{
- mce_request_packet(ir, data, size, MCEUSB_RX);
+ mce_request_packet(ir, NULL, size, MCEUSB_RX);
}
/* Send data out the IR blaster port(s) */
@@ -794,7 +806,7 @@
ir->carrier = carrier;
cmdbuf[2] = MCE_CMD_SIG_END;
cmdbuf[3] = MCE_IRDATA_TRAILER;
- dev_dbg(ir->dev, "%s: disabling carrier "
+ mce_dbg(ir->dev, "%s: disabling carrier "
"modulation\n", __func__);
mce_async_out(ir, cmdbuf, sizeof(cmdbuf));
return carrier;
@@ -806,7 +818,7 @@
ir->carrier = carrier;
cmdbuf[2] = prescaler;
cmdbuf[3] = divisor;
- dev_dbg(ir->dev, "%s: requesting %u HZ "
+ mce_dbg(ir->dev, "%s: requesting %u HZ "
"carrier\n", __func__, carrier);
/* Transmit new carrier to mce device */
@@ -879,7 +891,7 @@
rawir.duration = (ir->buf_in[i] & MCE_PULSE_MASK)
* US_TO_NS(MCE_TIME_UNIT);
- dev_dbg(ir->dev, "Storing %s with duration %d\n",
+ mce_dbg(ir->dev, "Storing %s with duration %d\n",
rawir.pulse ? "pulse" : "space",
rawir.duration);
@@ -911,7 +923,7 @@
if (ir->parser_state != CMD_HEADER && !ir->rem)
ir->parser_state = CMD_HEADER;
}
- dev_dbg(ir->dev, "processed IR data, calling ir_raw_event_handle\n");
+ mce_dbg(ir->dev, "processed IR data, calling ir_raw_event_handle\n");
ir_raw_event_handle(ir->rc);
}
@@ -933,7 +945,7 @@
if (ir->send_flags == RECV_FLAG_IN_PROGRESS) {
ir->send_flags = SEND_FLAG_COMPLETE;
- dev_dbg(ir->dev, "setup answer received %d bytes\n",
+ mce_dbg(ir->dev, "setup answer received %d bytes\n",
buf_len);
}
@@ -951,7 +963,7 @@
case -EPIPE:
default:
- dev_dbg(ir->dev, "Error: urb status = %d\n", urb->status);
+ mce_dbg(ir->dev, "Error: urb status = %d\n", urb->status);
break;
}
@@ -961,7 +973,6 @@
static void mceusb_gen1_init(struct mceusb_dev *ir)
{
int ret;
- int maxp = ir->len_in;
struct device *dev = ir->dev;
char *data;
@@ -978,8 +989,8 @@
ret = usb_control_msg(ir->usbdev, usb_rcvctrlpipe(ir->usbdev, 0),
USB_REQ_SET_ADDRESS, USB_TYPE_VENDOR, 0, 0,
data, USB_CTRL_MSG_SZ, HZ * 3);
- dev_dbg(dev, "%s - ret = %d\n", __func__, ret);
- dev_dbg(dev, "%s - data[0] = %d, data[1] = %d\n",
+ mce_dbg(dev, "%s - ret = %d\n", __func__, ret);
+ mce_dbg(dev, "%s - data[0] = %d, data[1] = %d\n",
__func__, data[0], data[1]);
/* set feature: bit rate 38400 bps */
@@ -987,71 +998,56 @@
USB_REQ_SET_FEATURE, USB_TYPE_VENDOR,
0xc04e, 0x0000, NULL, 0, HZ * 3);
- dev_dbg(dev, "%s - ret = %d\n", __func__, ret);
+ mce_dbg(dev, "%s - ret = %d\n", __func__, ret);
/* bRequest 4: set char length to 8 bits */
ret = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0),
4, USB_TYPE_VENDOR,
0x0808, 0x0000, NULL, 0, HZ * 3);
- dev_dbg(dev, "%s - retB = %d\n", __func__, ret);
+ mce_dbg(dev, "%s - retB = %d\n", __func__, ret);
/* bRequest 2: set handshaking to use DTR/DSR */
ret = usb_control_msg(ir->usbdev, usb_sndctrlpipe(ir->usbdev, 0),
2, USB_TYPE_VENDOR,
0x0000, 0x0100, NULL, 0, HZ * 3);
- dev_dbg(dev, "%s - retC = %d\n", __func__, ret);
+ mce_dbg(dev, "%s - retC = %d\n", __func__, ret);
/* device reset */
mce_async_out(ir, DEVICE_RESET, sizeof(DEVICE_RESET));
- mce_sync_in(ir, NULL, maxp);
/* get hw/sw revision? */
mce_async_out(ir, GET_REVISION, sizeof(GET_REVISION));
- mce_sync_in(ir, NULL, maxp);
kfree(data);
};
static void mceusb_gen2_init(struct mceusb_dev *ir)
{
- int maxp = ir->len_in;
-
/* device reset */
mce_async_out(ir, DEVICE_RESET, sizeof(DEVICE_RESET));
- mce_sync_in(ir, NULL, maxp);
/* get hw/sw revision? */
mce_async_out(ir, GET_REVISION, sizeof(GET_REVISION));
- mce_sync_in(ir, NULL, maxp);
/* unknown what the next two actually return... */
mce_async_out(ir, GET_UNKNOWN, sizeof(GET_UNKNOWN));
- mce_sync_in(ir, NULL, maxp);
mce_async_out(ir, GET_UNKNOWN2, sizeof(GET_UNKNOWN2));
- mce_sync_in(ir, NULL, maxp);
}
static void mceusb_get_parameters(struct mceusb_dev *ir)
{
- int maxp = ir->len_in;
-
/* get the carrier and frequency */
mce_async_out(ir, GET_CARRIER_FREQ, sizeof(GET_CARRIER_FREQ));
- mce_sync_in(ir, NULL, maxp);
- if (!ir->flags.no_tx) {
+ if (!ir->flags.no_tx)
/* get the transmitter bitmask */
mce_async_out(ir, GET_TX_BITMASK, sizeof(GET_TX_BITMASK));
- mce_sync_in(ir, NULL, maxp);
- }
/* get receiver timeout value */
mce_async_out(ir, GET_RX_TIMEOUT, sizeof(GET_RX_TIMEOUT));
- mce_sync_in(ir, NULL, maxp);
/* get receiver sensor setting */
mce_async_out(ir, GET_RX_SENSOR, sizeof(GET_RX_SENSOR));
- mce_sync_in(ir, NULL, maxp);
}
static struct rc_dev *mceusb_init_rc_dev(struct mceusb_dev *ir)
@@ -1122,7 +1118,7 @@
bool tx_mask_normal;
int ir_intfnum;
- dev_dbg(&intf->dev, "%s called\n", __func__);
+ mce_dbg(&intf->dev, "%s called\n", __func__);
idesc = intf->cur_altsetting;
@@ -1150,7 +1146,7 @@
ep_in = ep;
ep_in->bmAttributes = USB_ENDPOINT_XFER_INT;
ep_in->bInterval = 1;
- dev_dbg(&intf->dev, "acceptable inbound endpoint "
+ mce_dbg(&intf->dev, "acceptable inbound endpoint "
"found\n");
}
@@ -1165,12 +1161,12 @@
ep_out = ep;
ep_out->bmAttributes = USB_ENDPOINT_XFER_INT;
ep_out->bInterval = 1;
- dev_dbg(&intf->dev, "acceptable outbound endpoint "
+ mce_dbg(&intf->dev, "acceptable outbound endpoint "
"found\n");
}
}
if (ep_in == NULL) {
- dev_dbg(&intf->dev, "inbound and/or endpoint not found\n");
+ mce_dbg(&intf->dev, "inbound and/or endpoint not found\n");
return -ENODEV;
}
@@ -1215,16 +1211,16 @@
if (!ir->rc)
goto rc_dev_fail;
- /* flush buffers on the device */
- mce_sync_in(ir, NULL, maxp);
- mce_sync_in(ir, NULL, maxp);
-
/* wire up inbound data handler */
usb_fill_int_urb(ir->urb_in, dev, pipe, ir->buf_in,
maxp, (usb_complete_t) mceusb_dev_recv, ir, ep_in->bInterval);
ir->urb_in->transfer_dma = ir->dma_in;
ir->urb_in->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+ /* flush buffers on the device */
+ mce_dbg(&intf->dev, "Flushing receive buffers\n");
+ mce_flush_rx_buffer(ir, maxp);
+
/* initialize device */
if (ir->flags.microsoft_gen1)
mceusb_gen1_init(ir);
diff --git a/drivers/media/rc/nuvoton-cir.c b/drivers/media/rc/nuvoton-cir.c
index bf3060e..565f24c 100644
--- a/drivers/media/rc/nuvoton-cir.c
+++ b/drivers/media/rc/nuvoton-cir.c
@@ -991,7 +991,6 @@
unsigned long flags;
spin_lock_irqsave(&nvt->nvt_lock, flags);
- nvt->in_use = true;
nvt_enable_cir(nvt);
spin_unlock_irqrestore(&nvt->nvt_lock, flags);
@@ -1004,7 +1003,6 @@
unsigned long flags;
spin_lock_irqsave(&nvt->nvt_lock, flags);
- nvt->in_use = false;
nvt_disable_cir(nvt);
spin_unlock_irqrestore(&nvt->nvt_lock, flags);
}
diff --git a/drivers/media/rc/nuvoton-cir.h b/drivers/media/rc/nuvoton-cir.h
index 379795d..1241fc8 100644
--- a/drivers/media/rc/nuvoton-cir.h
+++ b/drivers/media/rc/nuvoton-cir.h
@@ -70,7 +70,6 @@
struct ir_raw_event rawir;
spinlock_t nvt_lock;
- bool in_use;
/* for rx */
u8 buf[RX_BUF_LEN];
diff --git a/drivers/media/rc/rc-main.c b/drivers/media/rc/rc-main.c
index f57cd56..3186ac7 100644
--- a/drivers/media/rc/rc-main.c
+++ b/drivers/media/rc/rc-main.c
@@ -522,18 +522,20 @@
/**
* ir_do_keyup() - internal function to signal the release of a keypress
* @dev: the struct rc_dev descriptor of the device
+ * @sync: whether or not to call input_sync
*
* This function is used internally to release a keypress, it must be
* called with keylock held.
*/
-static void ir_do_keyup(struct rc_dev *dev)
+static void ir_do_keyup(struct rc_dev *dev, bool sync)
{
if (!dev->keypressed)
return;
IR_dprintk(1, "keyup key 0x%04x\n", dev->last_keycode);
input_report_key(dev->input_dev, dev->last_keycode, 0);
- input_sync(dev->input_dev);
+ if (sync)
+ input_sync(dev->input_dev);
dev->keypressed = false;
}
@@ -549,7 +551,7 @@
unsigned long flags;
spin_lock_irqsave(&dev->keylock, flags);
- ir_do_keyup(dev);
+ ir_do_keyup(dev, true);
spin_unlock_irqrestore(&dev->keylock, flags);
}
EXPORT_SYMBOL_GPL(rc_keyup);
@@ -578,7 +580,7 @@
*/
spin_lock_irqsave(&dev->keylock, flags);
if (time_is_before_eq_jiffies(dev->keyup_jiffies))
- ir_do_keyup(dev);
+ ir_do_keyup(dev, true);
spin_unlock_irqrestore(&dev->keylock, flags);
}
@@ -597,6 +599,7 @@
spin_lock_irqsave(&dev->keylock, flags);
input_event(dev->input_dev, EV_MSC, MSC_SCAN, dev->last_scancode);
+ input_sync(dev->input_dev);
if (!dev->keypressed)
goto out;
@@ -622,29 +625,28 @@
static void ir_do_keydown(struct rc_dev *dev, int scancode,
u32 keycode, u8 toggle)
{
+ bool new_event = !dev->keypressed ||
+ dev->last_scancode != scancode ||
+ dev->last_toggle != toggle;
+
+ if (new_event && dev->keypressed)
+ ir_do_keyup(dev, false);
+
input_event(dev->input_dev, EV_MSC, MSC_SCAN, scancode);
- /* Repeat event? */
- if (dev->keypressed &&
- dev->last_scancode == scancode &&
- dev->last_toggle == toggle)
- return;
+ if (new_event && keycode != KEY_RESERVED) {
+ /* Register a keypress */
+ dev->keypressed = true;
+ dev->last_scancode = scancode;
+ dev->last_toggle = toggle;
+ dev->last_keycode = keycode;
- /* Release old keypress */
- ir_do_keyup(dev);
+ IR_dprintk(1, "%s: key down event, "
+ "key 0x%04x, scancode 0x%04x\n",
+ dev->input_name, keycode, scancode);
+ input_report_key(dev->input_dev, keycode, 1);
+ }
- dev->last_scancode = scancode;
- dev->last_toggle = toggle;
- dev->last_keycode = keycode;
-
- if (keycode == KEY_RESERVED)
- return;
-
- /* Register a keypress */
- dev->keypressed = true;
- IR_dprintk(1, "%s: key down event, key 0x%04x, scancode 0x%04x\n",
- dev->input_name, keycode, scancode);
- input_report_key(dev->input_dev, dev->last_keycode, 1);
input_sync(dev->input_dev);
}
diff --git a/drivers/media/video/m5mols/m5mols.h b/drivers/media/video/m5mols/m5mols.h
index 10b55c8..89d09a8 100644
--- a/drivers/media/video/m5mols/m5mols.h
+++ b/drivers/media/video/m5mols/m5mols.h
@@ -2,10 +2,10 @@
* Header for M-5MOLS 8M Pixel camera sensor with ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -106,23 +106,23 @@
* The each value according to each scenemode is recommended in the documents.
*/
struct m5mols_scenemode {
- u32 metering;
- u32 ev_bias;
- u32 wb_mode;
- u32 wb_preset;
- u32 chroma_en;
- u32 chroma_lvl;
- u32 edge_en;
- u32 edge_lvl;
- u32 af_range;
- u32 fd_mode;
- u32 mcc;
- u32 light;
- u32 flash;
- u32 tone;
- u32 iso;
- u32 capt_mode;
- u32 wdr;
+ u8 metering;
+ u8 ev_bias;
+ u8 wb_mode;
+ u8 wb_preset;
+ u8 chroma_en;
+ u8 chroma_lvl;
+ u8 edge_en;
+ u8 edge_lvl;
+ u8 af_range;
+ u8 fd_mode;
+ u8 mcc;
+ u8 light;
+ u8 flash;
+ u8 tone;
+ u8 iso;
+ u8 capt_mode;
+ u8 wdr;
};
/**
@@ -154,7 +154,6 @@
u8 str[VERSION_STRING_SIZE];
u8 af;
};
-#define VERSION_SIZE sizeof(struct m5mols_version)
/**
* struct m5mols_info - M-5MOLS driver data structure
@@ -216,9 +215,9 @@
bool lock_ae;
bool lock_awb;
u8 resolution;
- u32 interrupt;
- u32 mode;
- u32 mode_save;
+ u8 interrupt;
+ u8 mode;
+ u8 mode_save;
int (*set_power)(struct device *dev, int on);
};
@@ -256,9 +255,11 @@
* +-------+---+----------+-----+------+------+------+------+
* - d[0..3]: according to size1
*/
-int m5mols_read(struct v4l2_subdev *sd, u32 reg_comb, u32 *val);
+int m5mols_read_u8(struct v4l2_subdev *sd, u32 reg_comb, u8 *val);
+int m5mols_read_u16(struct v4l2_subdev *sd, u32 reg_comb, u16 *val);
+int m5mols_read_u32(struct v4l2_subdev *sd, u32 reg_comb, u32 *val);
int m5mols_write(struct v4l2_subdev *sd, u32 reg_comb, u32 val);
-int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u32 value);
+int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u8 value);
/*
* Mode operation of the M-5MOLS
@@ -280,12 +281,12 @@
* The available executing order between each modes are as follows:
* PARAMETER <---> MONITOR <---> CAPTURE
*/
-int m5mols_mode(struct m5mols_info *info, u32 mode);
+int m5mols_mode(struct m5mols_info *info, u8 mode);
-int m5mols_enable_interrupt(struct v4l2_subdev *sd, u32 reg);
+int m5mols_enable_interrupt(struct v4l2_subdev *sd, u8 reg);
int m5mols_sync_controls(struct m5mols_info *info);
int m5mols_start_capture(struct m5mols_info *info);
-int m5mols_do_scenemode(struct m5mols_info *info, u32 mode);
+int m5mols_do_scenemode(struct m5mols_info *info, u8 mode);
int m5mols_lock_3a(struct m5mols_info *info, bool lock);
int m5mols_set_ctrl(struct v4l2_ctrl *ctrl);
diff --git a/drivers/media/video/m5mols/m5mols_capture.c b/drivers/media/video/m5mols/m5mols_capture.c
index d71a390..d947192 100644
--- a/drivers/media/video/m5mols/m5mols_capture.c
+++ b/drivers/media/video/m5mols/m5mols_capture.c
@@ -2,10 +2,10 @@
* The Capture code for Fujitsu M-5MOLS ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -58,9 +58,9 @@
{
u32 num, den;
- int ret = m5mols_read(sd, addr_num, &num);
+ int ret = m5mols_read_u32(sd, addr_num, &num);
if (!ret)
- ret = m5mols_read(sd, addr_den, &den);
+ ret = m5mols_read_u32(sd, addr_den, &den);
if (ret)
return ret;
*val = den == 0 ? 0 : num / den;
@@ -99,20 +99,20 @@
if (ret)
return ret;
- ret = m5mols_read(sd, EXIF_INFO_ISO, (u32 *)&exif->iso_speed);
+ ret = m5mols_read_u16(sd, EXIF_INFO_ISO, &exif->iso_speed);
if (!ret)
- ret = m5mols_read(sd, EXIF_INFO_FLASH, (u32 *)&exif->flash);
+ ret = m5mols_read_u16(sd, EXIF_INFO_FLASH, &exif->flash);
if (!ret)
- ret = m5mols_read(sd, EXIF_INFO_SDR, (u32 *)&exif->sdr);
+ ret = m5mols_read_u16(sd, EXIF_INFO_SDR, &exif->sdr);
if (!ret)
- ret = m5mols_read(sd, EXIF_INFO_QVAL, (u32 *)&exif->qval);
+ ret = m5mols_read_u16(sd, EXIF_INFO_QVAL, &exif->qval);
if (ret)
return ret;
if (!ret)
- ret = m5mols_read(sd, CAPC_IMAGE_SIZE, &info->cap.main);
+ ret = m5mols_read_u32(sd, CAPC_IMAGE_SIZE, &info->cap.main);
if (!ret)
- ret = m5mols_read(sd, CAPC_THUMB_SIZE, &info->cap.thumb);
+ ret = m5mols_read_u32(sd, CAPC_THUMB_SIZE, &info->cap.thumb);
if (!ret)
info->cap.total = info->cap.main + info->cap.thumb;
@@ -122,7 +122,7 @@
int m5mols_start_capture(struct m5mols_info *info)
{
struct v4l2_subdev *sd = &info->sd;
- u32 resolution = info->resolution;
+ u8 resolution = info->resolution;
int timeout;
int ret;
diff --git a/drivers/media/video/m5mols/m5mols_controls.c b/drivers/media/video/m5mols/m5mols_controls.c
index 817c16f..d135d20 100644
--- a/drivers/media/video/m5mols/m5mols_controls.c
+++ b/drivers/media/video/m5mols/m5mols_controls.c
@@ -2,10 +2,10 @@
* Controls for M-5MOLS 8M Pixel camera sensor with ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -130,7 +130,7 @@
*
* WARNING: The execution order is important. Do not change the order.
*/
-int m5mols_do_scenemode(struct m5mols_info *info, u32 mode)
+int m5mols_do_scenemode(struct m5mols_info *info, u8 mode)
{
struct v4l2_subdev *sd = &info->sd;
struct m5mols_scenemode scenemode = m5mols_default_scenemode[mode];
diff --git a/drivers/media/video/m5mols/m5mols_core.c b/drivers/media/video/m5mols/m5mols_core.c
index 76eac26..43c68f5 100644
--- a/drivers/media/video/m5mols/m5mols_core.c
+++ b/drivers/media/video/m5mols/m5mols_core.c
@@ -2,10 +2,10 @@
* Driver for M-5MOLS 8M Pixel camera sensor with ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -133,13 +133,13 @@
/**
* m5mols_read - I2C read function
* @reg: combination of size, category and command for the I2C packet
+ * @size: desired size of I2C packet
* @val: read value
*/
-int m5mols_read(struct v4l2_subdev *sd, u32 reg, u32 *val)
+static int m5mols_read(struct v4l2_subdev *sd, u32 size, u32 reg, u32 *val)
{
struct i2c_client *client = v4l2_get_subdevdata(sd);
u8 rbuf[M5MOLS_I2C_MAX_SIZE + 1];
- u8 size = I2C_SIZE(reg);
u8 category = I2C_CATEGORY(reg);
u8 cmd = I2C_COMMAND(reg);
struct i2c_msg msg[2];
@@ -149,11 +149,6 @@
if (!client->adapter)
return -ENODEV;
- if (size != 1 && size != 2 && size != 4) {
- v4l2_err(sd, "Wrong data size\n");
- return -EINVAL;
- }
-
msg[0].addr = client->addr;
msg[0].flags = 0;
msg[0].len = 5;
@@ -184,6 +179,52 @@
return 0;
}
+int m5mols_read_u8(struct v4l2_subdev *sd, u32 reg, u8 *val)
+{
+ u32 val_32;
+ int ret;
+
+ if (I2C_SIZE(reg) != 1) {
+ v4l2_err(sd, "Wrong data size\n");
+ return -EINVAL;
+ }
+
+ ret = m5mols_read(sd, I2C_SIZE(reg), reg, &val_32);
+ if (ret)
+ return ret;
+
+ *val = (u8)val_32;
+ return ret;
+}
+
+int m5mols_read_u16(struct v4l2_subdev *sd, u32 reg, u16 *val)
+{
+ u32 val_32;
+ int ret;
+
+ if (I2C_SIZE(reg) != 2) {
+ v4l2_err(sd, "Wrong data size\n");
+ return -EINVAL;
+ }
+
+ ret = m5mols_read(sd, I2C_SIZE(reg), reg, &val_32);
+ if (ret)
+ return ret;
+
+ *val = (u16)val_32;
+ return ret;
+}
+
+int m5mols_read_u32(struct v4l2_subdev *sd, u32 reg, u32 *val)
+{
+ if (I2C_SIZE(reg) != 4) {
+ v4l2_err(sd, "Wrong data size\n");
+ return -EINVAL;
+ }
+
+ return m5mols_read(sd, I2C_SIZE(reg), reg, val);
+}
+
/**
* m5mols_write - I2C command write function
* @reg: combination of size, category and command for the I2C packet
@@ -231,13 +272,14 @@
return 0;
}
-int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u32 mask)
+int m5mols_busy(struct v4l2_subdev *sd, u8 category, u8 cmd, u8 mask)
{
- u32 busy, i;
+ u8 busy;
+ int i;
int ret;
for (i = 0; i < M5MOLS_I2C_CHECK_RETRY; i++) {
- ret = m5mols_read(sd, I2C_REG(category, cmd, 1), &busy);
+ ret = m5mols_read_u8(sd, I2C_REG(category, cmd, 1), &busy);
if (ret < 0)
return ret;
if ((busy & mask) == mask)
@@ -252,14 +294,14 @@
* Before writing desired interrupt value the INT_FACTOR register should
* be read to clear pending interrupts.
*/
-int m5mols_enable_interrupt(struct v4l2_subdev *sd, u32 reg)
+int m5mols_enable_interrupt(struct v4l2_subdev *sd, u8 reg)
{
struct m5mols_info *info = to_m5mols(sd);
- u32 mask = is_available_af(info) ? REG_INT_AF : 0;
- u32 dummy;
+ u8 mask = is_available_af(info) ? REG_INT_AF : 0;
+ u8 dummy;
int ret;
- ret = m5mols_read(sd, SYSTEM_INT_FACTOR, &dummy);
+ ret = m5mols_read_u8(sd, SYSTEM_INT_FACTOR, &dummy);
if (!ret)
ret = m5mols_write(sd, SYSTEM_INT_ENABLE, reg & ~mask);
return ret;
@@ -271,7 +313,7 @@
* It always accompanies a little delay changing the M-5MOLS mode, so it is
* needed checking current busy status to guarantee right mode.
*/
-static int m5mols_reg_mode(struct v4l2_subdev *sd, u32 mode)
+static int m5mols_reg_mode(struct v4l2_subdev *sd, u8 mode)
{
int ret = m5mols_write(sd, SYSTEM_SYSMODE, mode);
@@ -286,16 +328,16 @@
* can be guaranteed only when the sensor is operating in mode which which
* a command belongs to.
*/
-int m5mols_mode(struct m5mols_info *info, u32 mode)
+int m5mols_mode(struct m5mols_info *info, u8 mode)
{
struct v4l2_subdev *sd = &info->sd;
int ret = -EINVAL;
- u32 reg;
+ u8 reg;
if (mode < REG_PARAMETER && mode > REG_CAPTURE)
return ret;
- ret = m5mols_read(sd, SYSTEM_SYSMODE, ®);
+ ret = m5mols_read_u8(sd, SYSTEM_SYSMODE, ®);
if ((!ret && reg == mode) || ret)
return ret;
@@ -344,41 +386,37 @@
static int m5mols_get_version(struct v4l2_subdev *sd)
{
struct m5mols_info *info = to_m5mols(sd);
- union {
- struct m5mols_version ver;
- u8 bytes[VERSION_SIZE];
- } version;
- u32 *value;
- u8 cmd = CAT0_VER_CUSTOMER;
+ struct m5mols_version *ver = &info->ver;
+ u8 *str = ver->str;
+ int i;
int ret;
- do {
- value = (u32 *)&version.bytes[cmd];
- ret = m5mols_read(sd, SYSTEM_CMD(cmd), value);
- if (ret)
- return ret;
- } while (cmd++ != CAT0_VER_AWB);
-
- do {
- value = (u32 *)&version.bytes[cmd];
- ret = m5mols_read(sd, SYSTEM_VER_STRING, value);
- if (ret)
- return ret;
- if (cmd >= VERSION_SIZE - 1)
- return -EINVAL;
- } while (version.bytes[cmd++]);
-
- value = (u32 *)&version.bytes[cmd];
- ret = m5mols_read(sd, AF_VERSION, value);
+ ret = m5mols_read_u8(sd, SYSTEM_VER_CUSTOMER, &ver->customer);
+ if (!ret)
+ ret = m5mols_read_u8(sd, SYSTEM_VER_PROJECT, &ver->project);
+ if (!ret)
+ ret = m5mols_read_u16(sd, SYSTEM_VER_FIRMWARE, &ver->fw);
+ if (!ret)
+ ret = m5mols_read_u16(sd, SYSTEM_VER_HARDWARE, &ver->hw);
+ if (!ret)
+ ret = m5mols_read_u16(sd, SYSTEM_VER_PARAMETER, &ver->param);
+ if (!ret)
+ ret = m5mols_read_u16(sd, SYSTEM_VER_AWB, &ver->awb);
+ if (!ret)
+ ret = m5mols_read_u8(sd, AF_VERSION, &ver->af);
if (ret)
return ret;
- /* store version information swapped for being readable */
- info->ver = version.ver;
- info->ver.fw = be16_to_cpu(info->ver.fw);
- info->ver.hw = be16_to_cpu(info->ver.hw);
- info->ver.param = be16_to_cpu(info->ver.param);
- info->ver.awb = be16_to_cpu(info->ver.awb);
+ for (i = 0; i < VERSION_STRING_SIZE; i++) {
+ ret = m5mols_read_u8(sd, SYSTEM_VER_STRING, &str[i]);
+ if (ret)
+ return ret;
+ }
+
+ ver->fw = be16_to_cpu(ver->fw);
+ ver->hw = be16_to_cpu(ver->hw);
+ ver->param = be16_to_cpu(ver->param);
+ ver->awb = be16_to_cpu(ver->awb);
v4l2_info(sd, "Manufacturer\t[%s]\n",
is_manufacturer(info, REG_SAMSUNG_ELECTRO) ?
@@ -722,7 +760,7 @@
int ret;
/* Determine value's range & step of controls for various FW version */
- ret = m5mols_read(sd, AE_MAX_GAIN_MON, (u32 *)&max_exposure);
+ ret = m5mols_read_u16(sd, AE_MAX_GAIN_MON, &max_exposure);
if (!ret)
step_zoom = is_manufacturer(info, REG_SAMSUNG_OPTICS) ? 31 : 1;
if (ret)
@@ -842,18 +880,18 @@
struct m5mols_info *info =
container_of(work, struct m5mols_info, work_irq);
struct v4l2_subdev *sd = &info->sd;
- u32 reg;
+ u8 reg;
int ret;
if (!is_powered(info) ||
- m5mols_read(sd, SYSTEM_INT_FACTOR, &info->interrupt))
+ m5mols_read_u8(sd, SYSTEM_INT_FACTOR, &info->interrupt))
return;
switch (info->interrupt & REG_INT_MASK) {
case REG_INT_AF:
if (!is_available_af(info))
break;
- ret = m5mols_read(sd, AF_STATUS, ®);
+ ret = m5mols_read_u8(sd, AF_STATUS, ®);
v4l2_dbg(2, m5mols_debug, sd, "AF %s\n",
reg == REG_AF_FAIL ? "Failed" :
reg == REG_AF_SUCCESS ? "Success" :
diff --git a/drivers/media/video/m5mols/m5mols_reg.h b/drivers/media/video/m5mols/m5mols_reg.h
index b83e36f..c755bd6 100644
--- a/drivers/media/video/m5mols/m5mols_reg.h
+++ b/drivers/media/video/m5mols/m5mols_reg.h
@@ -2,10 +2,10 @@
* Register map for M-5MOLS 8M Pixel camera sensor with ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -56,13 +56,24 @@
* more specific contents, see definition if file m5mols.h.
*/
#define CAT0_VER_CUSTOMER 0x00 /* customer version */
-#define CAT0_VER_AWB 0x09 /* Auto WB version */
+#define CAT0_VER_PROJECT 0x01 /* project version */
+#define CAT0_VER_FIRMWARE 0x02 /* Firmware version */
+#define CAT0_VER_HARDWARE 0x04 /* Hardware version */
+#define CAT0_VER_PARAMETER 0x06 /* Parameter version */
+#define CAT0_VER_AWB 0x08 /* Auto WB version */
#define CAT0_VER_STRING 0x0a /* string including M-5MOLS */
#define CAT0_SYSMODE 0x0b /* SYSTEM mode register */
#define CAT0_STATUS 0x0c /* SYSTEM mode status register */
#define CAT0_INT_FACTOR 0x10 /* interrupt pending register */
#define CAT0_INT_ENABLE 0x11 /* interrupt enable register */
+#define SYSTEM_VER_CUSTOMER I2C_REG(CAT_SYSTEM, CAT0_VER_CUSTOMER, 1)
+#define SYSTEM_VER_PROJECT I2C_REG(CAT_SYSTEM, CAT0_VER_PROJECT, 1)
+#define SYSTEM_VER_FIRMWARE I2C_REG(CAT_SYSTEM, CAT0_VER_FIRMWARE, 2)
+#define SYSTEM_VER_HARDWARE I2C_REG(CAT_SYSTEM, CAT0_VER_HARDWARE, 2)
+#define SYSTEM_VER_PARAMETER I2C_REG(CAT_SYSTEM, CAT0_VER_PARAMETER, 2)
+#define SYSTEM_VER_AWB I2C_REG(CAT_SYSTEM, CAT0_VER_AWB, 2)
+
#define SYSTEM_SYSMODE I2C_REG(CAT_SYSTEM, CAT0_SYSMODE, 1)
#define REG_SYSINIT 0x00 /* SYSTEM mode */
#define REG_PARAMETER 0x01 /* PARAMETER mode */
@@ -382,8 +393,8 @@
#define REG_CAP_START_MAIN 0x01
#define REG_CAP_START_THUMB 0x03
-#define CAPC_IMAGE_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_IMAGE_SIZE, 1)
-#define CAPC_THUMB_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_THUMB_SIZE, 1)
+#define CAPC_IMAGE_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_IMAGE_SIZE, 4)
+#define CAPC_THUMB_SIZE I2C_REG(CAT_CAPT_CTRL, CATC_CAP_THUMB_SIZE, 4)
/*
* Category F - Flash
diff --git a/drivers/media/video/mx1_camera.c b/drivers/media/video/mx1_camera.c
index bc0c23a..63f8a0c 100644
--- a/drivers/media/video/mx1_camera.c
+++ b/drivers/media/video/mx1_camera.c
@@ -444,12 +444,9 @@
{
struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
struct mx1_camera_dev *pcdev = ici->priv;
- int ret;
- if (pcdev->icd) {
- ret = -EBUSY;
- goto ebusy;
- }
+ if (pcdev->icd)
+ return -EBUSY;
dev_info(icd->dev.parent, "MX1 Camera driver attached to camera %d\n",
icd->devnum);
@@ -458,8 +455,7 @@
pcdev->icd = icd;
-ebusy:
- return ret;
+ return 0;
}
static void mx1_camera_remove_device(struct soc_camera_device *icd)
diff --git a/drivers/media/video/omap/omap_vout.c b/drivers/media/video/omap/omap_vout.c
index 4ada9be..4d07c58 100644
--- a/drivers/media/video/omap/omap_vout.c
+++ b/drivers/media/video/omap/omap_vout.c
@@ -982,6 +982,14 @@
startindex = (vout->vid == OMAP_VIDEO1) ?
video1_numbuffers : video2_numbuffers;
+ /* Check the size of the buffer */
+ if (*size > vout->buffer_size) {
+ v4l2_err(&vout->vid_dev->v4l2_dev,
+ "buffer allocation mismatch [%u] [%u]\n",
+ *size, vout->buffer_size);
+ return -ENOMEM;
+ }
+
for (i = startindex; i < *count; i++) {
vout->buffer_size = *size;
@@ -1228,6 +1236,14 @@
(vma->vm_pgoff << PAGE_SHIFT));
return -EINVAL;
}
+ /* Check the size of the buffer */
+ if (size > vout->buffer_size) {
+ v4l2_err(&vout->vid_dev->v4l2_dev,
+ "insufficient memory [%lu] [%u]\n",
+ size, vout->buffer_size);
+ return -ENOMEM;
+ }
+
q->bufs[i]->baddr = vma->vm_start;
vma->vm_flags |= VM_RESERVED;
@@ -2391,7 +2407,7 @@
/* Register the Video device with V4L2
*/
vfd = vout->vfd;
- if (video_register_device(vfd, VFL_TYPE_GRABBER, k + 1) < 0) {
+ if (video_register_device(vfd, VFL_TYPE_GRABBER, -1) < 0) {
dev_err(&pdev->dev, ": Could not register "
"Video for Linux device\n");
vfd->minor = -1;
diff --git a/drivers/media/video/omap/omap_voutlib.c b/drivers/media/video/omap/omap_voutlib.c
index 2aa6a76..8ae7481 100644
--- a/drivers/media/video/omap/omap_voutlib.c
+++ b/drivers/media/video/omap/omap_voutlib.c
@@ -193,7 +193,7 @@
return -EINVAL;
if (cpu_is_omap24xx()) {
- if (crop->height != win->w.height) {
+ if (try_crop.height != win->w.height) {
/* If we're resizing vertically, we can't support a
* crop width wider than 768 pixels.
*/
@@ -202,7 +202,7 @@
}
}
/* vertical resizing */
- vresize = (1024 * crop->height) / win->w.height;
+ vresize = (1024 * try_crop.height) / win->w.height;
if (cpu_is_omap24xx() && (vresize > 2048))
vresize = 2048;
else if (cpu_is_omap34xx() && (vresize > 4096))
@@ -221,7 +221,7 @@
try_crop.height = 2;
}
/* horizontal resizing */
- hresize = (1024 * crop->width) / win->w.width;
+ hresize = (1024 * try_crop.width) / win->w.width;
if (cpu_is_omap24xx() && (hresize > 2048))
hresize = 2048;
else if (cpu_is_omap34xx() && (hresize > 4096))
diff --git a/drivers/media/video/omap3isp/isp.c b/drivers/media/video/omap3isp/isp.c
index c9fd04e..94b6ed8 100644
--- a/drivers/media/video/omap3isp/isp.c
+++ b/drivers/media/video/omap3isp/isp.c
@@ -1748,7 +1748,7 @@
goto done;
/* Register external entities */
- for (subdevs = pdata->subdevs; subdevs->subdevs; ++subdevs) {
+ for (subdevs = pdata->subdevs; subdevs && subdevs->subdevs; ++subdevs) {
struct v4l2_subdev *sensor;
struct media_entity *input;
unsigned int flags;
diff --git a/drivers/media/video/pwc/pwc-ctrl.c b/drivers/media/video/pwc/pwc-ctrl.c
index 1593f8d..760b4de 100644
--- a/drivers/media/video/pwc/pwc-ctrl.c
+++ b/drivers/media/video/pwc/pwc-ctrl.c
@@ -1414,7 +1414,7 @@
{
ARG_DEF(struct pwc_probe, probe)
- strcpy(ARGR(probe).name, pdev->vdev->name);
+ strcpy(ARGR(probe).name, pdev->vdev.name);
ARGR(probe).type = pdev->type;
ARG_OUT(probe)
break;
diff --git a/drivers/media/video/pwc/pwc-if.c b/drivers/media/video/pwc/pwc-if.c
index 356cd42..b0bde5a 100644
--- a/drivers/media/video/pwc/pwc-if.c
+++ b/drivers/media/video/pwc/pwc-if.c
@@ -40,7 +40,7 @@
Oh yes, convention: to disctinguish between all the various pointers to
device-structures, I use these names for the pointer variables:
udev: struct usb_device *
- vdev: struct video_device *
+ vdev: struct video_device (member of pwc_dev)
pdev: struct pwc_devive *
*/
@@ -152,6 +152,7 @@
size_t count, loff_t *ppos);
static unsigned int pwc_video_poll(struct file *file, poll_table *wait);
static int pwc_video_mmap(struct file *file, struct vm_area_struct *vma);
+static void pwc_video_release(struct video_device *vfd);
static const struct v4l2_file_operations pwc_fops = {
.owner = THIS_MODULE,
@@ -164,42 +165,12 @@
};
static struct video_device pwc_template = {
.name = "Philips Webcam", /* Filled in later */
- .release = video_device_release,
+ .release = pwc_video_release,
.fops = &pwc_fops,
+ .ioctl_ops = &pwc_ioctl_ops,
};
/***************************************************************************/
-
-/* Okay, this is some magic that I worked out and the reasoning behind it...
-
- The biggest problem with any USB device is of course: "what to do
- when the user unplugs the device while it is in use by an application?"
- We have several options:
- 1) Curse them with the 7 plagues when they do (requires divine intervention)
- 2) Tell them not to (won't work: they'll do it anyway)
- 3) Oops the kernel (this will have a negative effect on a user's uptime)
- 4) Do something sensible.
-
- Of course, we go for option 4.
-
- It happens that this device will be linked to two times, once from
- usb_device and once from the video_device in their respective 'private'
- pointers. This is done when the device is probed() and all initialization
- succeeded. The pwc_device struct links back to both structures.
-
- When a device is unplugged while in use it will be removed from the
- list of known USB devices; I also de-register it as a V4L device, but
- unfortunately I can't free the memory since the struct is still in use
- by the file descriptor. This free-ing is then deferend until the first
- opportunity. Crude, but it works.
-
- A small 'advantage' is that if a user unplugs the cam and plugs it back
- in, it should get assigned the same video device minor, but unfortunately
- it's non-trivial to re-link the cam back to the video device... (that
- would surely be magic! :))
-*/
-
-/***************************************************************************/
/* Private functions */
/* Here we want the physical address of the memory.
@@ -1016,16 +987,15 @@
static DEVICE_ATTR(button, S_IRUGO | S_IWUSR, show_snapshot_button_status,
NULL);
-static int pwc_create_sysfs_files(struct video_device *vdev)
+static int pwc_create_sysfs_files(struct pwc_device *pdev)
{
- struct pwc_device *pdev = video_get_drvdata(vdev);
int rc;
- rc = device_create_file(&vdev->dev, &dev_attr_button);
+ rc = device_create_file(&pdev->vdev.dev, &dev_attr_button);
if (rc)
goto err;
if (pdev->features & FEATURE_MOTOR_PANTILT) {
- rc = device_create_file(&vdev->dev, &dev_attr_pan_tilt);
+ rc = device_create_file(&pdev->vdev.dev, &dev_attr_pan_tilt);
if (rc)
goto err_button;
}
@@ -1033,19 +1003,17 @@
return 0;
err_button:
- device_remove_file(&vdev->dev, &dev_attr_button);
+ device_remove_file(&pdev->vdev.dev, &dev_attr_button);
err:
PWC_ERROR("Could not create sysfs files.\n");
return rc;
}
-static void pwc_remove_sysfs_files(struct video_device *vdev)
+static void pwc_remove_sysfs_files(struct pwc_device *pdev)
{
- struct pwc_device *pdev = video_get_drvdata(vdev);
-
if (pdev->features & FEATURE_MOTOR_PANTILT)
- device_remove_file(&vdev->dev, &dev_attr_pan_tilt);
- device_remove_file(&vdev->dev, &dev_attr_button);
+ device_remove_file(&pdev->vdev.dev, &dev_attr_pan_tilt);
+ device_remove_file(&pdev->vdev.dev, &dev_attr_button);
}
#ifdef CONFIG_USB_PWC_DEBUG
@@ -1106,7 +1074,7 @@
if (ret >= 0)
{
PWC_DEBUG_OPEN("This %s camera is equipped with a %s (%d).\n",
- pdev->vdev->name,
+ pdev->vdev.name,
pwc_sensor_type_to_string(i), i);
}
}
@@ -1180,16 +1148,15 @@
return 0;
}
-
-static void pwc_cleanup(struct pwc_device *pdev)
+static void pwc_video_release(struct video_device *vfd)
{
- pwc_remove_sysfs_files(pdev->vdev);
- video_unregister_device(pdev->vdev);
+ struct pwc_device *pdev = container_of(vfd, struct pwc_device, vdev);
+ int hint;
-#ifdef CONFIG_USB_PWC_INPUT_EVDEV
- if (pdev->button_dev)
- input_unregister_device(pdev->button_dev);
-#endif
+ /* search device_hint[] table if we occupy a slot, by any chance */
+ for (hint = 0; hint < MAX_DEV_HINTS; hint++)
+ if (device_hint[hint].pdev == pdev)
+ device_hint[hint].pdev = NULL;
kfree(pdev);
}
@@ -1199,7 +1166,7 @@
{
struct video_device *vdev = file->private_data;
struct pwc_device *pdev;
- int i, hint;
+ int i;
PWC_DEBUG_OPEN(">> video_close called(vdev = 0x%p).\n", vdev);
@@ -1234,12 +1201,6 @@
}
pdev->vopen--;
PWC_DEBUG_OPEN("<< video_close() vopen=%d\n", pdev->vopen);
- } else {
- pwc_cleanup(pdev);
- /* search device_hint[] table if we occupy a slot, by any chance */
- for (hint = 0; hint < MAX_DEV_HINTS; hint++)
- if (device_hint[hint].pdev == pdev)
- device_hint[hint].pdev = NULL;
}
return 0;
@@ -1715,19 +1676,12 @@
init_waitqueue_head(&pdev->frameq);
pdev->vcompression = pwc_preferred_compression;
- /* Allocate video_device structure */
- pdev->vdev = video_device_alloc();
- if (!pdev->vdev) {
- PWC_ERROR("Err, cannot allocate video_device struture. Failing probe.");
- rc = -ENOMEM;
- goto err_free_mem;
- }
- memcpy(pdev->vdev, &pwc_template, sizeof(pwc_template));
- pdev->vdev->parent = &intf->dev;
- pdev->vdev->lock = &pdev->modlock;
- pdev->vdev->ioctl_ops = &pwc_ioctl_ops;
- strcpy(pdev->vdev->name, name);
- video_set_drvdata(pdev->vdev, pdev);
+ /* Init video_device structure */
+ memcpy(&pdev->vdev, &pwc_template, sizeof(pwc_template));
+ pdev->vdev.parent = &intf->dev;
+ pdev->vdev.lock = &pdev->modlock;
+ strcpy(pdev->vdev.name, name);
+ video_set_drvdata(&pdev->vdev, pdev);
pdev->release = le16_to_cpu(udev->descriptor.bcdDevice);
PWC_DEBUG_PROBE("Release: %04x\n", pdev->release);
@@ -1746,8 +1700,6 @@
}
}
- pdev->vdev->release = video_device_release;
-
/* occupy slot */
if (hint < MAX_DEV_HINTS)
device_hint[hint].pdev = pdev;
@@ -1759,16 +1711,16 @@
pwc_set_leds(pdev, 0, 0);
pwc_camera_power(pdev, 0);
- rc = video_register_device(pdev->vdev, VFL_TYPE_GRABBER, video_nr);
+ rc = video_register_device(&pdev->vdev, VFL_TYPE_GRABBER, video_nr);
if (rc < 0) {
PWC_ERROR("Failed to register as video device (%d).\n", rc);
- goto err_video_release;
+ goto err_free_mem;
}
- rc = pwc_create_sysfs_files(pdev->vdev);
+ rc = pwc_create_sysfs_files(pdev);
if (rc)
goto err_video_unreg;
- PWC_INFO("Registered as %s.\n", video_device_node_name(pdev->vdev));
+ PWC_INFO("Registered as %s.\n", video_device_node_name(&pdev->vdev));
#ifdef CONFIG_USB_PWC_INPUT_EVDEV
/* register webcam snapshot button input device */
@@ -1776,7 +1728,7 @@
if (!pdev->button_dev) {
PWC_ERROR("Err, insufficient memory for webcam snapshot button device.");
rc = -ENOMEM;
- pwc_remove_sysfs_files(pdev->vdev);
+ pwc_remove_sysfs_files(pdev);
goto err_video_unreg;
}
@@ -1794,7 +1746,7 @@
if (rc) {
input_free_device(pdev->button_dev);
pdev->button_dev = NULL;
- pwc_remove_sysfs_files(pdev->vdev);
+ pwc_remove_sysfs_files(pdev);
goto err_video_unreg;
}
#endif
@@ -1804,10 +1756,7 @@
err_video_unreg:
if (hint < MAX_DEV_HINTS)
device_hint[hint].pdev = NULL;
- video_unregister_device(pdev->vdev);
- pdev->vdev = NULL; /* So we don't try to release it below */
-err_video_release:
- video_device_release(pdev->vdev);
+ video_unregister_device(&pdev->vdev);
err_free_mem:
kfree(pdev);
return rc;
@@ -1816,10 +1765,8 @@
/* The user yanked out the cable... */
static void usb_pwc_disconnect(struct usb_interface *intf)
{
- struct pwc_device *pdev;
- int hint;
+ struct pwc_device *pdev = usb_get_intfdata(intf);
- pdev = usb_get_intfdata (intf);
mutex_lock(&pdev->modlock);
usb_set_intfdata (intf, NULL);
if (pdev == NULL) {
@@ -1836,30 +1783,25 @@
}
/* We got unplugged; this is signalled by an EPIPE error code */
- if (pdev->vopen) {
- PWC_INFO("Disconnected while webcam is in use!\n");
- pdev->error_status = EPIPE;
- }
+ pdev->error_status = EPIPE;
+ pdev->unplugged = 1;
/* Alert waiting processes */
wake_up_interruptible(&pdev->frameq);
- /* Wait until device is closed */
- if (pdev->vopen) {
- pdev->unplugged = 1;
- pwc_iso_stop(pdev);
- } else {
- /* Device is closed, so we can safely unregister it */
- PWC_DEBUG_PROBE("Unregistering video device in disconnect().\n");
+
+ /* No need to keep the urbs around after disconnection */
+ pwc_isoc_cleanup(pdev);
disconnect_out:
- /* search device_hint[] table if we occupy a slot, by any chance */
- for (hint = 0; hint < MAX_DEV_HINTS; hint++)
- if (device_hint[hint].pdev == pdev)
- device_hint[hint].pdev = NULL;
- }
-
mutex_unlock(&pdev->modlock);
- pwc_cleanup(pdev);
+
+ pwc_remove_sysfs_files(pdev);
+ video_unregister_device(&pdev->vdev);
+
+#ifdef CONFIG_USB_PWC_INPUT_EVDEV
+ if (pdev->button_dev)
+ input_unregister_device(pdev->button_dev);
+#endif
}
diff --git a/drivers/media/video/pwc/pwc.h b/drivers/media/video/pwc/pwc.h
index e947766..083f8b1 100644
--- a/drivers/media/video/pwc/pwc.h
+++ b/drivers/media/video/pwc/pwc.h
@@ -162,9 +162,9 @@
struct pwc_device
{
- struct video_device *vdev;
+ struct video_device vdev;
- /* Pointer to our usb_device */
+ /* Pointer to our usb_device, may be NULL after unplug */
struct usb_device *udev;
int type; /* type of cam (645, 646, 675, 680, 690, 720, 730, 740, 750) */
diff --git a/drivers/media/video/s5p-fimc/fimc-capture.c b/drivers/media/video/s5p-fimc/fimc-capture.c
index d142b40..81b4a82 100644
--- a/drivers/media/video/s5p-fimc/fimc-capture.c
+++ b/drivers/media/video/s5p-fimc/fimc-capture.c
@@ -1,7 +1,7 @@
/*
- * Samsung S5P SoC series camera interface (camera capture) driver
+ * Samsung S5P/EXYNOS4 SoC series camera interface (camera capture) driver
*
- * Copyright (c) 2010 Samsung Electronics Co., Ltd
+ * Copyright (C) 2010 - 2011 Samsung Electronics Co., Ltd.
* Author: Sylwester Nawrocki, <s.nawrocki@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
@@ -262,12 +262,7 @@
{
if (!fr || plane >= fr->fmt->memplanes)
return 0;
-
- dbg("%s: w: %d. h: %d. depth[%d]: %d",
- __func__, fr->width, fr->height, plane, fr->fmt->depth[plane]);
-
return fr->f_width * fr->f_height * fr->fmt->depth[plane] / 8;
-
}
static int queue_setup(struct vb2_queue *vq, unsigned int *num_buffers,
@@ -283,24 +278,14 @@
*num_planes = fmt->memplanes;
- dbg("%s, buffer count=%d, plane count=%d",
- __func__, *num_buffers, *num_planes);
-
for (i = 0; i < fmt->memplanes; i++) {
sizes[i] = get_plane_size(&ctx->d_frame, i);
- dbg("plane: %u, plane_size: %lu", i, sizes[i]);
allocators[i] = ctx->fimc_dev->alloc_ctx;
}
return 0;
}
-static int buffer_init(struct vb2_buffer *vb)
-{
- /* TODO: */
- return 0;
-}
-
static int buffer_prepare(struct vb2_buffer *vb)
{
struct vb2_queue *vq = vb->vb2_queue;
@@ -380,7 +365,6 @@
.queue_setup = queue_setup,
.buf_prepare = buffer_prepare,
.buf_queue = buffer_queue,
- .buf_init = buffer_init,
.wait_prepare = fimc_unlock,
.wait_finish = fimc_lock,
.start_streaming = start_streaming,
@@ -903,6 +887,7 @@
err_v4l2_reg:
v4l2_device_unregister(v4l2_dev);
err_info:
+ kfree(ctx);
dev_err(&fimc->pdev->dev, "failed to install\n");
return ret;
}
diff --git a/drivers/media/video/s5p-fimc/fimc-core.c b/drivers/media/video/s5p-fimc/fimc-core.c
index dc91a85..bdf19ad 100644
--- a/drivers/media/video/s5p-fimc/fimc-core.c
+++ b/drivers/media/video/s5p-fimc/fimc-core.c
@@ -1,9 +1,8 @@
/*
- * S5P camera interface (video postprocessor) driver
+ * Samsung S5P/EXYNOS4 SoC series camera interface (video postprocessor) driver
*
- * Copyright (c) 2010 Samsung Electronics Co., Ltd
- *
- * Sylwester Nawrocki, <s.nawrocki@samsung.com>
+ * Copyright (C) 2010-2011 Samsung Electronics Co., Ltd.
+ * Contact: Sylwester Nawrocki, <s.nawrocki@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published
@@ -42,7 +41,6 @@
.color = S5P_FIMC_RGB565,
.memplanes = 1,
.colplanes = 1,
- .mbus_code = V4L2_MBUS_FMT_RGB565_2X8_BE,
.flags = FMT_FLAGS_M2M,
}, {
.name = "BGR666",
@@ -232,11 +230,7 @@
return 0;
}
}
-
*shift = 0, *ratio = 1;
-
- dbg("s: %d, t: %d, shift: %d, ratio: %d",
- src, tar, *shift, *ratio);
return 0;
}
@@ -268,10 +262,8 @@
err("invalid source size: %d x %d", sx, sy);
return -EINVAL;
}
-
sc->real_width = sx;
sc->real_height = sy;
- dbg("sx= %d, sy= %d, tx= %d, ty= %d", sx, sy, tx, ty);
ret = fimc_get_scaler_factor(sx, tx, &sc->pre_hratio, &sc->hfactor);
if (ret)
@@ -711,22 +703,18 @@
f = ctx_get_frame(ctx, vq->type);
if (IS_ERR(f))
return PTR_ERR(f);
-
/*
* Return number of non-contigous planes (plane buffers)
* depending on the configured color format.
*/
- if (f->fmt)
- *num_planes = f->fmt->memplanes;
+ if (!f->fmt)
+ return -EINVAL;
+ *num_planes = f->fmt->memplanes;
for (i = 0; i < f->fmt->memplanes; i++) {
- sizes[i] = (f->width * f->height * f->fmt->depth[i]) >> 3;
+ sizes[i] = (f->f_width * f->f_height * f->fmt->depth[i]) / 8;
allocators[i] = ctx->fimc_dev->alloc_ctx;
}
-
- if (*num_buffers == 0)
- *num_buffers = 1;
-
return 0;
}
@@ -852,7 +840,7 @@
for (i = 0; i < ARRAY_SIZE(fimc_formats); ++i) {
fmt = &fimc_formats[i];
- if (fmt->fourcc == f->fmt.pix.pixelformat &&
+ if (fmt->fourcc == f->fmt.pix_mp.pixelformat &&
(fmt->flags & mask))
break;
}
diff --git a/drivers/media/video/s5p-fimc/fimc-core.h b/drivers/media/video/s5p-fimc/fimc-core.h
index 3beb1e5..1f70772 100644
--- a/drivers/media/video/s5p-fimc/fimc-core.h
+++ b/drivers/media/video/s5p-fimc/fimc-core.h
@@ -1,7 +1,5 @@
/*
- * Copyright (c) 2010 Samsung Electronics
- *
- * Sylwester Nawrocki, <s.nawrocki@samsung.com>
+ * Copyright (C) 2010 - 2011 Samsung Electronics Co., Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -135,9 +133,10 @@
* @name: format description
* @fourcc: the fourcc code for this format, 0 if not applicable
* @color: the corresponding fimc_color_fmt
- * @depth: per plane driver's private 'number of bits per pixel'
* @memplanes: number of physically non-contiguous data planes
* @colplanes: number of physically contiguous data planes
+ * @depth: per plane driver's private 'number of bits per pixel'
+ * @flags: flags indicating which operation mode format applies to
*/
struct fimc_fmt {
enum v4l2_mbus_pixelcode mbus_code;
@@ -171,7 +170,7 @@
};
/**
- * struct fimc_effect - the configuration data for the "Arbitrary" image effect
+ * struct fimc_effect - color effect information
* @type: effect type
* @pat_cb: cr value when type is "arbitrary"
* @pat_cr: cr value when type is "arbitrary"
@@ -184,7 +183,6 @@
/**
* struct fimc_scaler - the configuration data for FIMC inetrnal scaler
- *
* @scaleup_h: flag indicating scaling up horizontally
* @scaleup_v: flag indicating scaling up vertically
* @copy_mode: flag indicating transparent DMA transfer (no scaling
@@ -220,7 +218,6 @@
/**
* struct fimc_addr - the FIMC physical address set for DMA
- *
* @y: luminance plane physical address
* @cb: Cb plane physical address
* @cr: Cr plane physical address
@@ -234,6 +231,7 @@
/**
* struct fimc_vid_buffer - the driver's video buffer
* @vb: v4l videobuf buffer
+ * @list: linked list structure for buffer queue
* @paddr: precalculated physical address set
* @index: buffer index for the output DMA engine
*/
@@ -254,11 +252,10 @@
* @offs_v: image vertical pixel offset
* @width: image pixel width
* @height: image pixel weight
- * @paddr: image frame buffer physical addresses
- * @buf_cnt: number of buffers depending on a color format
* @payload: image size in bytes (w x h x bpp)
- * @color: color format
+ * @paddr: image frame buffer physical addresses
* @dma_offset: DMA offset in bytes
+ * @fmt: fimc color format pointer
*/
struct fimc_frame {
u32 f_width;
@@ -390,21 +387,22 @@
/**
* struct fimc_dev - abstraction for FIMC entity
- *
* @slock: the spinlock protecting this data structure
* @lock: the mutex protecting this data structure
* @pdev: pointer to the FIMC platform device
* @pdata: pointer to the device platform data
+ * @variant: the IP variant information
* @id: FIMC device index (0..FIMC_MAX_DEVS)
* @num_clocks: the number of clocks managed by this device instance
- * @clock[]: the clocks required for FIMC operation
+ * @clock: clocks required for FIMC operation
* @regs: the mapped hardware registers
* @regs_res: the resource claimed for IO registers
- * @irq: interrupt number of the FIMC subdevice
- * @irq_queue:
+ * @irq: FIMC interrupt number
+ * @irq_queue: interrupt handler waitqueue
* @m2m: memory-to-memory V4L2 device information
* @vid_cap: camera capture device information
* @state: flags used to synchronize m2m and capture mode operation
+ * @alloc_ctx: videobuf2 memory allocator context
*/
struct fimc_dev {
spinlock_t slock;
@@ -427,8 +425,7 @@
/**
* fimc_ctx - the device context data
- *
- * @lock: mutex protecting this data structure
+ * @slock: spinlock protecting this data structure
* @s_frame: source frame properties
* @d_frame: destination frame properties
* @out_order_1p: output 1-plane YCBCR order
diff --git a/drivers/media/video/saa7134/saa7134-input.c b/drivers/media/video/saa7134/saa7134-input.c
index ff6c0e9..d4ee24b 100644
--- a/drivers/media/video/saa7134/saa7134-input.c
+++ b/drivers/media/video/saa7134/saa7134-input.c
@@ -963,7 +963,7 @@
* to work with other protocols.
*/
if (!ir->active) {
- timeout = jiffies + jiffies_to_msecs(15);
+ timeout = jiffies + msecs_to_jiffies(15);
mod_timer(&ir->timer, timeout);
ir->active = true;
}
diff --git a/drivers/media/video/uvc/uvc_entity.c b/drivers/media/video/uvc/uvc_entity.c
index c3ab0c8..48fea37 100644
--- a/drivers/media/video/uvc/uvc_entity.c
+++ b/drivers/media/video/uvc/uvc_entity.c
@@ -27,14 +27,20 @@
struct uvc_entity *entity)
{
const u32 flags = MEDIA_LNK_FL_ENABLED | MEDIA_LNK_FL_IMMUTABLE;
- struct uvc_entity *remote;
+ struct media_entity *sink;
unsigned int i;
- u8 remote_pad;
- int ret = 0;
+ int ret;
+
+ sink = (UVC_ENTITY_TYPE(entity) == UVC_TT_STREAMING)
+ ? (entity->vdev ? &entity->vdev->entity : NULL)
+ : &entity->subdev.entity;
+ if (sink == NULL)
+ return 0;
for (i = 0; i < entity->num_pads; ++i) {
struct media_entity *source;
- struct media_entity *sink;
+ struct uvc_entity *remote;
+ u8 remote_pad;
if (!(entity->pads[i].flags & MEDIA_PAD_FL_SINK))
continue;
@@ -43,10 +49,11 @@
if (remote == NULL)
return -EINVAL;
- source = (UVC_ENTITY_TYPE(remote) == UVC_TT_STREAMING)
- ? &remote->vdev->entity : &remote->subdev.entity;
- sink = (UVC_ENTITY_TYPE(entity) == UVC_TT_STREAMING)
- ? &entity->vdev->entity : &entity->subdev.entity;
+ source = (UVC_ENTITY_TYPE(remote) != UVC_TT_STREAMING)
+ ? (remote->vdev ? &remote->vdev->entity : NULL)
+ : &remote->subdev.entity;
+ if (source == NULL)
+ continue;
remote_pad = remote->num_pads - 1;
ret = media_entity_create_link(source, remote_pad,
@@ -55,11 +62,10 @@
return ret;
}
- if (UVC_ENTITY_TYPE(entity) != UVC_TT_STREAMING)
- ret = v4l2_device_register_subdev(&chain->dev->vdev,
- &entity->subdev);
+ if (UVC_ENTITY_TYPE(entity) == UVC_TT_STREAMING)
+ return 0;
- return ret;
+ return v4l2_device_register_subdev(&chain->dev->vdev, &entity->subdev);
}
static struct v4l2_subdev_ops uvc_subdev_ops = {
@@ -84,9 +90,11 @@
ret = media_entity_init(&entity->subdev.entity,
entity->num_pads, entity->pads, 0);
- } else
+ } else if (entity->vdev != NULL) {
ret = media_entity_init(&entity->vdev->entity,
entity->num_pads, entity->pads, 0);
+ } else
+ ret = 0;
return ret;
}
diff --git a/drivers/media/video/uvc/uvc_queue.c b/drivers/media/video/uvc/uvc_queue.c
index 109a063..f90ce9f 100644
--- a/drivers/media/video/uvc/uvc_queue.c
+++ b/drivers/media/video/uvc/uvc_queue.c
@@ -104,6 +104,8 @@
}
if (queue->count) {
+ uvc_queue_cancel(queue, 0);
+ INIT_LIST_HEAD(&queue->mainqueue);
vfree(queue->mem);
queue->count = 0;
}
diff --git a/drivers/media/video/uvc/uvc_video.c b/drivers/media/video/uvc/uvc_video.c
index fc766b9..4999479 100644
--- a/drivers/media/video/uvc/uvc_video.c
+++ b/drivers/media/video/uvc/uvc_video.c
@@ -1255,8 +1255,10 @@
/* Commit the streaming parameters. */
ret = uvc_commit_video(stream, &stream->ctrl);
- if (ret < 0)
+ if (ret < 0) {
+ uvc_queue_enable(&stream->queue, 0);
return ret;
+ }
return uvc_init_video(stream, GFP_KERNEL);
}
diff --git a/drivers/media/video/v4l2-dev.c b/drivers/media/video/v4l2-dev.c
index 19d5ae2..06f1400 100644
--- a/drivers/media/video/v4l2-dev.c
+++ b/drivers/media/video/v4l2-dev.c
@@ -167,6 +167,12 @@
mutex_unlock(&videodev_lock);
+#if defined(CONFIG_MEDIA_CONTROLLER)
+ if (vdev->v4l2_dev && vdev->v4l2_dev->mdev &&
+ vdev->vfl_type != VFL_TYPE_SUBDEV)
+ media_device_unregister_entity(&vdev->entity);
+#endif
+
/* Release video_device and perform other
cleanups as needed. */
vdev->release(vdev);
@@ -389,9 +395,6 @@
static int v4l2_open(struct inode *inode, struct file *filp)
{
struct video_device *vdev;
-#if defined(CONFIG_MEDIA_CONTROLLER)
- struct media_entity *entity = NULL;
-#endif
int ret = 0;
/* Check if the video device is available */
@@ -405,17 +408,6 @@
/* and increase the device refcount */
video_get(vdev);
mutex_unlock(&videodev_lock);
-#if defined(CONFIG_MEDIA_CONTROLLER)
- if (vdev->v4l2_dev && vdev->v4l2_dev->mdev &&
- vdev->vfl_type != VFL_TYPE_SUBDEV) {
- entity = media_entity_get(&vdev->entity);
- if (!entity) {
- ret = -EBUSY;
- video_put(vdev);
- return ret;
- }
- }
-#endif
if (vdev->fops->open) {
if (vdev->lock && mutex_lock_interruptible(vdev->lock)) {
ret = -ERESTARTSYS;
@@ -431,14 +423,8 @@
err:
/* decrease the refcount in case of an error */
- if (ret) {
-#if defined(CONFIG_MEDIA_CONTROLLER)
- if (vdev->v4l2_dev && vdev->v4l2_dev->mdev &&
- vdev->vfl_type != VFL_TYPE_SUBDEV)
- media_entity_put(entity);
-#endif
+ if (ret)
video_put(vdev);
- }
return ret;
}
@@ -455,11 +441,6 @@
if (vdev->lock)
mutex_unlock(vdev->lock);
}
-#if defined(CONFIG_MEDIA_CONTROLLER)
- if (vdev->v4l2_dev && vdev->v4l2_dev->mdev &&
- vdev->vfl_type != VFL_TYPE_SUBDEV)
- media_entity_put(&vdev->entity);
-#endif
/* decrease the refcount unconditionally since the release()
return value is ignored. */
video_put(vdev);
@@ -754,12 +735,6 @@
if (!vdev || !video_is_registered(vdev))
return;
-#if defined(CONFIG_MEDIA_CONTROLLER)
- if (vdev->v4l2_dev && vdev->v4l2_dev->mdev &&
- vdev->vfl_type != VFL_TYPE_SUBDEV)
- media_device_unregister_entity(&vdev->entity);
-#endif
-
mutex_lock(&videodev_lock);
/* This must be in a critical section to prevent a race with v4l2_open.
* Once this bit has been cleared video_get may never be called again.
diff --git a/drivers/media/video/videobuf2-core.c b/drivers/media/video/videobuf2-core.c
index 6ba1461..3015e600 100644
--- a/drivers/media/video/videobuf2-core.c
+++ b/drivers/media/video/videobuf2-core.c
@@ -492,13 +492,6 @@
return -EINVAL;
}
- /*
- * If the same number of buffers and memory access method is requested
- * then return immediately.
- */
- if (q->memory == req->memory && req->count == q->num_buffers)
- return 0;
-
if (req->count == 0 || q->num_buffers != 0 || q->memory != req->memory) {
/*
* We already have buffers allocated, so first check if they
@@ -539,9 +532,9 @@
/* Finally, allocate buffers and video memory */
ret = __vb2_queue_alloc(q, req->memory, num_buffers, num_planes,
plane_sizes);
- if (ret < 0) {
- dprintk(1, "Memory allocation failed with error: %d\n", ret);
- return ret;
+ if (ret == 0) {
+ dprintk(1, "Memory allocation failed\n");
+ return -ENOMEM;
}
/*
@@ -1196,6 +1189,7 @@
* has not already dequeued before initiating cancel.
*/
INIT_LIST_HEAD(&q->done_list);
+ atomic_set(&q->queued_count, 0);
wake_up_all(&q->done_wq);
/*
diff --git a/drivers/media/video/videobuf2-dma-sg.c b/drivers/media/video/videobuf2-dma-sg.c
index b2d9485..10a20d9 100644
--- a/drivers/media/video/videobuf2-dma-sg.c
+++ b/drivers/media/video/videobuf2-dma-sg.c
@@ -62,7 +62,7 @@
goto fail_pages_array_alloc;
for (i = 0; i < buf->sg_desc.num_pages; ++i) {
- buf->pages[i] = alloc_page(GFP_KERNEL | __GFP_ZERO);
+ buf->pages[i] = alloc_page(GFP_KERNEL | __GFP_ZERO | __GFP_NOWARN);
if (NULL == buf->pages[i])
goto fail_pages_alloc;
sg_set_page(&buf->sg_desc.sglist[i],
diff --git a/drivers/staging/lirc/lirc_imon.c b/drivers/staging/lirc/lirc_imon.c
index 4039eda..4a9e563 100644
--- a/drivers/staging/lirc/lirc_imon.c
+++ b/drivers/staging/lirc/lirc_imon.c
@@ -672,8 +672,6 @@
static void usb_rx_callback(struct urb *urb)
{
struct imon_context *context;
- unsigned char *buf;
- int len;
int intfnum = 0;
if (!urb)
@@ -683,9 +681,6 @@
if (!context)
return;
- buf = urb->transfer_buffer;
- len = urb->actual_length;
-
switch (urb->status) {
case -ENOENT: /* usbcore unlink successful! */
return;
@@ -728,7 +723,6 @@
int ir_ep_found = 0;
int alloc_status = 0;
int vfd_proto_6p = 0;
- int code_length;
struct imon_context *context = NULL;
int i;
u16 vendor, product;
@@ -749,8 +743,6 @@
else
context->display = 1;
- code_length = BUF_CHUNK_SIZE * 8;
-
usbdev = usb_get_dev(interface_to_usbdev(interface));
iface_desc = interface->cur_altsetting;
num_endpts = iface_desc->desc.bNumEndpoints;
@@ -856,7 +848,7 @@
strcpy(driver->name, MOD_NAME);
driver->minor = -1;
- driver->code_length = sizeof(int) * 8;
+ driver->code_length = BUF_CHUNK_SIZE * 8;
driver->sample_rate = 0;
driver->features = LIRC_CAN_REC_MODE2;
driver->data = context;
diff --git a/drivers/staging/lirc/lirc_serial.c b/drivers/staging/lirc/lirc_serial.c
index 4a3cca0..805df91 100644
--- a/drivers/staging/lirc/lirc_serial.c
+++ b/drivers/staging/lirc/lirc_serial.c
@@ -838,7 +838,23 @@
static int init_port(void)
{
- int i, nlow, nhigh;
+ int i, nlow, nhigh, result;
+
+ result = request_irq(irq, irq_handler,
+ IRQF_DISABLED | (share_irq ? IRQF_SHARED : 0),
+ LIRC_DRIVER_NAME, (void *)&hardware);
+
+ switch (result) {
+ case -EBUSY:
+ printk(KERN_ERR LIRC_DRIVER_NAME ": IRQ %d busy\n", irq);
+ return -EBUSY;
+ case -EINVAL:
+ printk(KERN_ERR LIRC_DRIVER_NAME
+ ": Bad irq number or handler\n");
+ return -EINVAL;
+ default:
+ break;
+ };
/* Reserve io region. */
/*
@@ -893,34 +909,17 @@
printk(KERN_INFO LIRC_DRIVER_NAME ": Manually using active "
"%s receiver\n", sense ? "low" : "high");
+ dprintk("Interrupt %d, port %04x obtained\n", irq, io);
return 0;
}
static int set_use_inc(void *data)
{
- int result;
unsigned long flags;
/* initialize timestamp */
do_gettimeofday(&lasttv);
- result = request_irq(irq, irq_handler,
- IRQF_DISABLED | (share_irq ? IRQF_SHARED : 0),
- LIRC_DRIVER_NAME, (void *)&hardware);
-
- switch (result) {
- case -EBUSY:
- printk(KERN_ERR LIRC_DRIVER_NAME ": IRQ %d busy\n", irq);
- return -EBUSY;
- case -EINVAL:
- printk(KERN_ERR LIRC_DRIVER_NAME
- ": Bad irq number or handler\n");
- return -EINVAL;
- default:
- dprintk("Interrupt %d, port %04x obtained\n", irq, io);
- break;
- }
-
spin_lock_irqsave(&hardware[type].lock, flags);
/* Set DLAB 0. */
@@ -945,10 +944,6 @@
soutp(UART_IER, sinp(UART_IER) &
(~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI)));
spin_unlock_irqrestore(&hardware[type].lock, flags);
-
- free_irq(irq, (void *)&hardware);
-
- dprintk("freed IRQ %d\n", irq);
}
static ssize_t lirc_write(struct file *file, const char *buf,
@@ -1256,6 +1251,9 @@
static void __exit lirc_serial_exit_module(void)
{
lirc_serial_exit();
+
+ free_irq(irq, (void *)&hardware);
+
if (iommap != 0)
release_mem_region(iommap, 8 << ioshift);
else
diff --git a/drivers/staging/lirc/lirc_sir.c b/drivers/staging/lirc/lirc_sir.c
index a7b46f2..0d38645 100644
--- a/drivers/staging/lirc/lirc_sir.c
+++ b/drivers/staging/lirc/lirc_sir.c
@@ -739,23 +739,16 @@
static void send_pulse(unsigned long len)
{
long bytes_out = len / TIME_CONST;
- long time_left;
- time_left = (long)len - (long)bytes_out * (long)TIME_CONST;
- if (bytes_out == 0) {
+ if (bytes_out == 0)
bytes_out++;
- time_left = 0;
- }
+
while (bytes_out--) {
outb(PULSE, io + UART_TX);
/* FIXME treba seriozne cakanie z char/serial.c */
while (!(inb(io + UART_LSR) & UART_LSR_THRE))
;
}
-#if 0
- if (time_left > 0)
- safe_udelay(time_left);
-#endif
}
#endif
diff --git a/drivers/staging/lirc/lirc_zilog.c b/drivers/staging/lirc/lirc_zilog.c
index dd6a57c..4e051f6 100644
--- a/drivers/staging/lirc/lirc_zilog.c
+++ b/drivers/staging/lirc/lirc_zilog.c
@@ -475,14 +475,14 @@
dprintk("poll thread started\n");
while (!kthread_should_stop()) {
+ set_current_state(TASK_INTERRUPTIBLE);
+
/* if device not opened, we can sleep half a second */
if (atomic_read(&ir->open_count) == 0) {
schedule_timeout(HZ/2);
continue;
}
- set_current_state(TASK_INTERRUPTIBLE);
-
/*
* This is ~113*2 + 24 + jitter (2*repeat gap + code length).
* We use this interval as the chip resets every time you poll
diff --git a/include/media/lirc_dev.h b/include/media/lirc_dev.h
index 630e702..168dd0b 100644
--- a/include/media/lirc_dev.h
+++ b/include/media/lirc_dev.h
@@ -9,7 +9,7 @@
#ifndef _LINUX_LIRC_DEV_H
#define _LINUX_LIRC_DEV_H
-#define MAX_IRCTL_DEVICES 4
+#define MAX_IRCTL_DEVICES 8
#define BUFLEN 16
#define mod(n, div) ((n) % (div))
diff --git a/include/media/m5mols.h b/include/media/m5mols.h
index 2d7e7ca..aac2c0e 100644
--- a/include/media/m5mols.h
+++ b/include/media/m5mols.h
@@ -2,10 +2,10 @@
* Driver header for M-5MOLS 8M Pixel camera sensor with ISP
*
* Copyright (C) 2011 Samsung Electronics Co., Ltd.
- * Author: HeungJun Kim, riverful.kim@samsung.com
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
*
* Copyright (C) 2009 Samsung Electronics Co., Ltd.
- * Author: Dongsoo Nathaniel Kim, dongsoo45.kim@samsung.com
+ * Author: Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by