[POWERPC] 8xx: Add mpc885ads support and common mpc8xx files
This adds the core 8xx stuff and specifically mpc885ads board-specific
bits to arch/powerpc. Respective Kconfig has been cleaned up from the stuff
not yet ported over to avoid confusion. Updated and cleaned version.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
diff --git a/arch/powerpc/platforms/8xx/mpc885ads.h b/arch/powerpc/platforms/8xx/mpc885ads.h
new file mode 100644
index 0000000..30cbebf
--- /dev/null
+++ b/arch/powerpc/platforms/8xx/mpc885ads.h
@@ -0,0 +1,95 @@
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Freescale MPC885ADS board.
+ * Copied from the FADS stuff.
+ *
+ * Author: MontaVista Software, Inc.
+ * source@mvista.com
+ *
+ * 2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_MPC885ADS_H__
+#define __ASM_MPC885ADS_H__
+
+#include <asm/ppcboot.h>
+#include <sysdev/fsl_soc.h>
+
+/* U-Boot maps BCSR to 0xff080000 */
+#define BCSR_ADDR ((uint)0xff080000)
+#define BCSR_SIZE ((uint)32)
+#define BCSR0 ((uint)(BCSR_ADDR + 0x00))
+#define BCSR1 ((uint)(BCSR_ADDR + 0x04))
+#define BCSR2 ((uint)(BCSR_ADDR + 0x08))
+#define BCSR3 ((uint)(BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint)(BCSR_ADDR + 0x10))
+
+#define CFG_PHYDEV_ADDR ((uint)0xff0a0000)
+#define BCSR5 ((uint)(CFG_PHYDEV_ADDR + 0x300))
+
+#define IMAP_ADDR (get_immrbase())
+#define IMAP_SIZE ((uint)(64 * 1024))
+
+#define MPC8xx_CPM_OFFSET (0x9c0)
+#define CPM_MAP_ADDR (get_immrbase() + MPC8xx_CPM_OFFSET)
+#define CPM_IRQ_OFFSET 16 // for compability with cpm_uart driver
+
+#define PCMCIA_MEM_ADDR (uint)0xff020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+/* Bits of interest in the BCSRs.
+ */
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDAEN ((uint)0x10000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVPP0 ((uint)0x00200000)
+#define BCSR1_PCCVPP1 ((uint)0x00100000)
+#define BCSR1_PCCVPP_MASK (BCSR1_PCCVPP0 | BCSR1_PCCVPP1)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+#define BCSR1_PCCVCC_MASK (BCSR1_PCCVCC0 | BCSR1_PCCVCC1)
+
+#define BCSR4_ETH10_RST ((uint)0x80000000) /* 10Base-T PHY reset*/
+#define BCSR4_USB_LO_SPD ((uint)0x04000000)
+#define BCSR4_USB_VCC ((uint)0x02000000)
+#define BCSR4_USB_FULL_SPD ((uint)0x00040000)
+#define BCSR4_USB_EN ((uint)0x00020000)
+
+#define BCSR5_MII2_EN 0x40
+#define BCSR5_MII2_RST 0x20
+#define BCSR5_T1_RST 0x10
+#define BCSR5_ATM155_RST 0x08
+#define BCSR5_ATM25_RST 0x04
+#define BCSR5_MII1_EN 0x02
+#define BCSR5_MII1_RST 0x01
+
+/* Interrupt level assignments */
+#define PHY_INTERRUPT SIU_IRQ7 /* PHY link change interrupt */
+#define SIU_INT_FEC1 SIU_LEVEL1 /* FEC1 interrupt */
+#define SIU_INT_FEC2 SIU_LEVEL3 /* FEC2 interrupt */
+#define FEC_INTERRUPT SIU_INT_FEC1 /* FEC interrupt */
+
+/* We don't use the 8259 */
+#define NR_8259_INTS 0
+
+/* CPM Ethernet through SCC3 */
+#define PA_ENET_RXD ((ushort)0x0040)
+#define PA_ENET_TXD ((ushort)0x0080)
+#define PE_ENET_TCLK ((uint)0x00004000)
+#define PE_ENET_RCLK ((uint)0x00008000)
+#define PE_ENET_TENA ((uint)0x00000010)
+#define PC_ENET_CLSN ((ushort)0x0400)
+#define PC_ENET_RENA ((ushort)0x0800)
+
+/* Control bits in the SICR to route TCLK (CLK5) and RCLK (CLK6) to
+ * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero */
+#define SICR_ENET_MASK ((uint)0x00ff0000)
+#define SICR_ENET_CLKRT ((uint)0x002c0000)
+
+#endif /* __ASM_MPC885ADS_H__ */
+#endif /* __KERNEL__ */