stmmac: initial support to manage pcs modes
This patch adds the minimal support to manage the PCS
modes (RGMII/SGMII) and restart the ANE.
Both TBI and RTBI are not yet supported.
Thanks to Byungho that wrote some part of this code
and tested SGMII too.
The only thing to be fixed is the get/set pause in
ethtool.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
index 479f479..942fdce 100644
--- a/drivers/net/ethernet/stmicro/stmmac/common.h
+++ b/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -144,6 +144,9 @@
unsigned long irq_pcs_ane_n;
unsigned long irq_pcs_link_n;
unsigned long irq_rgmii_n;
+ unsigned long pcs_link;
+ unsigned long pcs_duplex;
+ unsigned long pcs_speed;
};
/* CSR Frequency Access Defines*/
@@ -165,6 +168,12 @@
#define FLOW_TX 2
#define FLOW_AUTO (FLOW_TX | FLOW_RX)
+/* PCS defines */
+#define STMMAC_PCS_RGMII (1 << 0)
+#define STMMAC_PCS_SGMII (1 << 1)
+#define STMMAC_PCS_TBI (1 << 2)
+#define STMMAC_PCS_RTBI (1 << 3)
+
#define SF_DMA_MODE 1 /* DMA STORE-AND-FORWARD Operation Mode */
/* DAM HW feature register fields */
@@ -230,6 +239,16 @@
#define CORE_PCS_LINK_STATUS (1 << 6)
#define CORE_RGMII_IRQ (1 << 7)
+struct rgmii_adv {
+ unsigned int pause;
+ unsigned int duplex;
+ unsigned int lp_pause;
+ unsigned int lp_duplex;
+};
+
+#define STMMAC_PCS_PAUSE 1
+#define STMMAC_PCS_ASYM_PAUSE 2
+
/* DMA HW capabilities */
struct dma_features {
unsigned int mbps_10_100;
@@ -375,6 +394,8 @@
void (*reset_eee_mode) (void __iomem *ioaddr);
void (*set_eee_timer) (void __iomem *ioaddr, int ls, int tw);
void (*set_eee_pls) (void __iomem *ioaddr, int link);
+ void (*ctrl_ane) (void __iomem *ioaddr, bool restart);
+ void (*get_adv) (void __iomem *ioaddr, struct rgmii_adv *adv);
};
struct mac_link {
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
index 6dd689e..57f4e8f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
@@ -98,6 +98,38 @@
#define GMAC_TBI 0x000000d4 /* TBI extend status */
#define GMAC_S_R_GMII 0x000000d8 /* SGMII RGMII status */
+/* AN Configuration defines */
+#define GMAC_AN_CTRL_RAN 0x00000200 /* Restart Auto-Negotiation */
+#define GMAC_AN_CTRL_ANE 0x00001000 /* Auto-Negotiation Enable */
+#define GMAC_AN_CTRL_ELE 0x00004000 /* External Loopback Enable */
+#define GMAC_AN_CTRL_ECD 0x00010000 /* Enable Comma Detect */
+#define GMAC_AN_CTRL_LR 0x00020000 /* Lock to Reference */
+#define GMAC_AN_CTRL_SGMRAL 0x00040000 /* SGMII RAL Control */
+
+/* AN Status defines */
+#define GMAC_AN_STATUS_LS 0x00000004 /* Link Status 0:down 1:up */
+#define GMAC_AN_STATUS_ANA 0x00000008 /* Auto-Negotiation Ability */
+#define GMAC_AN_STATUS_ANC 0x00000020 /* Auto-Negotiation Complete */
+#define GMAC_AN_STATUS_ES 0x00000100 /* Extended Status */
+
+/* Register 54 (SGMII/RGMII status register) */
+#define GMAC_S_R_GMII_LINK 0x8
+#define GMAC_S_R_GMII_SPEED 0x5
+#define GMAC_S_R_GMII_SPEED_SHIFT 0x1
+#define GMAC_S_R_GMII_MODE 0x1
+#define GMAC_S_R_GMII_SPEED_125 2
+#define GMAC_S_R_GMII_SPEED_25 1
+
+/* Common ADV and LPA defines */
+#define GMAC_ANE_FD (1 << 5)
+#define GMAC_ANE_HD (1 << 6)
+#define GMAC_ANE_PSE (3 << 7)
+#define GMAC_ANE_PSE_SHIFT 7
+
+ /* GMAC Configuration defines */
+#define GMAC_CONTROL_TC 0x01000000 /* Transmit Conf. in RGMII/SGMII */
+#define GMAC_CONTROL_WD 0x00800000 /* Disable Watchdog on receive */
+
/* GMAC Configuration defines */
#define GMAC_CONTROL_TC 0x01000000 /* Transmit Conf. in RGMII/SGMII */
#define GMAC_CONTROL_WD 0x00800000 /* Disable Watchdog on receive */
@@ -232,5 +264,7 @@
#define GMAC_MMC_TX_INTR 0x108
#define GMAC_MMC_RX_CSUM_OFFLOAD 0x208
+
+
extern const struct stmmac_dma_ops dwmac1000_dma_ops;
#endif /* __DWMAC1000_H__ */
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
index ff4c79e..29138da 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
@@ -28,6 +28,7 @@
#include <linux/crc32.h>
#include <linux/slab.h>
+#include <linux/ethtool.h>
#include <asm/io.h>
#include "dwmac1000.h"
@@ -193,7 +194,6 @@
writel(pmt, ioaddr + GMAC_PMT);
}
-
static int dwmac1000_irq_status(void __iomem *ioaddr,
struct stmmac_extra_stats *x)
{
@@ -252,9 +252,30 @@
x->irq_pcs_ane_n++;
}
if (intr_status & rgmii_irq) {
- CHIP_DBG(KERN_INFO "GMAC RGMII IRQ status\n");
- readl(ioaddr + GMAC_S_R_GMII);
+ u32 status = readl(ioaddr + GMAC_S_R_GMII);
+ CHIP_DBG(KERN_INFO "GMAC RGMII/SGMII interrupt\n");
x->irq_rgmii_n++;
+
+ /* Save and dump the link status. */
+ if (status & GMAC_S_R_GMII_LINK) {
+ int speed_value = (status & GMAC_S_R_GMII_SPEED) >>
+ GMAC_S_R_GMII_SPEED_SHIFT;
+ x->pcs_duplex = (status & GMAC_S_R_GMII_MODE);
+
+ if (speed_value == GMAC_S_R_GMII_SPEED_125)
+ x->pcs_speed = SPEED_1000;
+ else if (speed_value == GMAC_S_R_GMII_SPEED_25)
+ x->pcs_speed = SPEED_100;
+ else
+ x->pcs_speed = SPEED_10;
+
+ x->pcs_link = 1;
+ pr_debug("Link is Up - %d/%s\n", (int) x->pcs_speed,
+ x->pcs_duplex ? "Full" : "Half");
+ } else {
+ x->pcs_link = 0;
+ pr_debug("Link is Down\n");
+ }
}
return ret;
@@ -309,6 +330,41 @@
writel(value, ioaddr + LPI_TIMER_CTRL);
}
+static void dwmac1000_ctrl_ane(void __iomem *ioaddr, bool restart)
+{
+ u32 value;
+
+ value = readl(ioaddr + GMAC_AN_CTRL);
+ /* auto negotiation enable and External Loopback enable */
+ value = GMAC_AN_CTRL_ANE | GMAC_AN_CTRL_ELE;
+
+ if (restart)
+ value |= GMAC_AN_CTRL_RAN;
+
+ writel(value, ioaddr + GMAC_AN_CTRL);
+}
+
+static void dwmac1000_get_adv(void __iomem *ioaddr, struct rgmii_adv *adv)
+{
+ u32 value = readl(ioaddr + GMAC_ANE_ADV);
+
+ if (value & GMAC_ANE_FD)
+ adv->duplex = DUPLEX_FULL;
+ if (value & GMAC_ANE_HD)
+ adv->duplex |= DUPLEX_HALF;
+
+ adv->pause = (value & GMAC_ANE_PSE) >> GMAC_ANE_PSE_SHIFT;
+
+ value = readl(ioaddr + GMAC_ANE_LPA);
+
+ if (value & GMAC_ANE_FD)
+ adv->lp_duplex = DUPLEX_FULL;
+ if (value & GMAC_ANE_HD)
+ adv->lp_duplex = DUPLEX_HALF;
+
+ adv->lp_pause = (value & GMAC_ANE_PSE) >> GMAC_ANE_PSE_SHIFT;
+}
+
static const struct stmmac_ops dwmac1000_ops = {
.core_init = dwmac1000_core_init,
.rx_ipc = dwmac1000_rx_ipc_enable,
@@ -323,6 +379,8 @@
.reset_eee_mode = dwmac1000_reset_eee_mode,
.set_eee_timer = dwmac1000_set_eee_timer,
.set_eee_pls = dwmac1000_set_eee_pls,
+ .ctrl_ane = dwmac1000_ctrl_ane,
+ .get_adv = dwmac1000_get_adv,
};
struct mac_device_info *dwmac1000_setup(void __iomem *ioaddr)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 9637d3e..182a838 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -97,6 +97,7 @@
u32 rx_riwt;
unsigned int mode;
int extend_desc;
+ int pcs;
};
extern int phyaddr;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 1793628..54e15db 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -246,6 +246,70 @@
struct stmmac_priv *priv = netdev_priv(dev);
struct phy_device *phy = priv->phydev;
int rc;
+
+ if ((priv->pcs & STMMAC_PCS_RGMII) || (priv->pcs & STMMAC_PCS_SGMII)) {
+ struct rgmii_adv adv;
+
+ if (!priv->xstats.pcs_link) {
+ ethtool_cmd_speed_set(cmd, SPEED_UNKNOWN);
+ cmd->duplex = DUPLEX_UNKNOWN;
+ return 0;
+ }
+ cmd->duplex = priv->xstats.pcs_duplex;
+
+ ethtool_cmd_speed_set(cmd, priv->xstats.pcs_speed);
+
+ /* Get and convert ADV/LP_ADV from the HW AN registers */
+ if (priv->hw->mac->get_adv)
+ priv->hw->mac->get_adv(priv->ioaddr, &adv);
+ else
+ return -EOPNOTSUPP; /* should never happen indeed */
+
+ /* Encoding of PSE bits is defined in 802.3z, 37.2.1.4 */
+
+ if (adv.pause & STMMAC_PCS_PAUSE)
+ cmd->advertising |= ADVERTISED_Pause;
+ if (adv.pause & STMMAC_PCS_ASYM_PAUSE)
+ cmd->advertising |= ADVERTISED_Asym_Pause;
+ if (adv.lp_pause & STMMAC_PCS_PAUSE)
+ cmd->lp_advertising |= ADVERTISED_Pause;
+ if (adv.lp_pause & STMMAC_PCS_ASYM_PAUSE)
+ cmd->lp_advertising |= ADVERTISED_Asym_Pause;
+
+ /* Reg49[3] always set because ANE is always supported */
+ cmd->autoneg = ADVERTISED_Autoneg;
+ cmd->supported |= SUPPORTED_Autoneg;
+ cmd->advertising |= ADVERTISED_Autoneg;
+ cmd->lp_advertising |= ADVERTISED_Autoneg;
+
+ if (adv.duplex) {
+ cmd->supported |= (SUPPORTED_1000baseT_Full |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_10baseT_Full);
+ cmd->advertising |= (ADVERTISED_1000baseT_Full |
+ ADVERTISED_100baseT_Full |
+ ADVERTISED_10baseT_Full);
+ } else {
+ cmd->supported |= (SUPPORTED_1000baseT_Half |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_10baseT_Half);
+ cmd->advertising |= (ADVERTISED_1000baseT_Half |
+ ADVERTISED_100baseT_Half |
+ ADVERTISED_10baseT_Half);
+ }
+ if (adv.lp_duplex)
+ cmd->lp_advertising |= (ADVERTISED_1000baseT_Full |
+ ADVERTISED_100baseT_Full |
+ ADVERTISED_10baseT_Full);
+ else
+ cmd->lp_advertising |= (ADVERTISED_1000baseT_Half |
+ ADVERTISED_100baseT_Half |
+ ADVERTISED_10baseT_Half);
+ cmd->port = PORT_OTHER;
+
+ return 0;
+ }
+
if (phy == NULL) {
pr_err("%s: %s: PHY is not registered\n",
__func__, dev->name);
@@ -270,6 +334,30 @@
struct phy_device *phy = priv->phydev;
int rc;
+ if ((priv->pcs & STMMAC_PCS_RGMII) || (priv->pcs & STMMAC_PCS_SGMII)) {
+ u32 mask = ADVERTISED_Autoneg | ADVERTISED_Pause;
+
+ /* Only support ANE */
+ if (cmd->autoneg != AUTONEG_ENABLE)
+ return -EINVAL;
+
+ if (cmd->autoneg == AUTONEG_ENABLE) {
+ mask &= (ADVERTISED_1000baseT_Half |
+ ADVERTISED_1000baseT_Full |
+ ADVERTISED_100baseT_Half |
+ ADVERTISED_100baseT_Full |
+ ADVERTISED_10baseT_Half |
+ ADVERTISED_10baseT_Full);
+
+ spin_lock(&priv->lock);
+ if (priv->hw->mac->ctrl_ane)
+ priv->hw->mac->ctrl_ane(priv->ioaddr, 1);
+ spin_unlock(&priv->lock);
+ }
+
+ return 0;
+ }
+
spin_lock(&priv->lock);
rc = phy_ethtool_sset(phy, cmd);
spin_unlock(&priv->lock);
@@ -339,6 +427,9 @@
{
struct stmmac_priv *priv = netdev_priv(netdev);
+ if (priv->pcs) /* FIXME */
+ return;
+
spin_lock(&priv->lock);
pause->rx_pause = 0;
@@ -362,6 +453,9 @@
int new_pause = FLOW_OFF;
int ret = 0;
+ if (priv->pcs) /* FIXME */
+ return -EOPNOTSUPP;
+
spin_lock(&priv->lock);
if (pause->rx_pause)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index ca3e95a..ac166be 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -405,6 +405,24 @@
DBG(probe, DEBUG, "stmmac_adjust_link: exiting\n");
}
+static void stmmac_check_pcs_mode(struct stmmac_priv *priv)
+{
+ int interface = priv->plat->interface;
+
+ if (priv->dma_cap.pcs) {
+ if ((interface & PHY_INTERFACE_MODE_RGMII) ||
+ (interface & PHY_INTERFACE_MODE_RGMII_ID) ||
+ (interface & PHY_INTERFACE_MODE_RGMII_RXID) ||
+ (interface & PHY_INTERFACE_MODE_RGMII_TXID)) {
+ pr_debug("STMMAC: PCS RGMII support enable\n");
+ priv->pcs = STMMAC_PCS_RGMII;
+ } else if (interface & PHY_INTERFACE_MODE_SGMII) {
+ pr_debug("STMMAC: PCS SGMII support enable\n");
+ priv->pcs = STMMAC_PCS_SGMII;
+ }
+ }
+}
+
/**
* stmmac_init_phy - PHY initialization
* @dev: net device structure
@@ -1141,10 +1159,13 @@
stmmac_check_ether_addr(priv);
- ret = stmmac_init_phy(dev);
- if (unlikely(ret)) {
- pr_err("%s: Cannot attach to PHY (error: %d)\n", __func__, ret);
- goto open_error;
+ if (!priv->pcs) {
+ ret = stmmac_init_phy(dev);
+ if (ret) {
+ pr_err("%s: Cannot attach to PHY (error: %d)\n",
+ __func__, ret);
+ goto open_error;
+ }
}
/* Create and initialize the TX/RX descriptors chains. */
@@ -1233,7 +1254,12 @@
phy_start(priv->phydev);
priv->tx_lpi_timer = STMMAC_DEFAULT_TWT_LS_TIMER;
- priv->eee_enabled = stmmac_eee_init(priv);
+
+ /* Using PCS we cannot dial with the phy registers at this stage
+ * so we do not support extra feature like EEE.
+ */
+ if (!priv->pcs)
+ priv->eee_enabled = stmmac_eee_init(priv);
stmmac_init_tx_coalesce(priv);
@@ -1242,6 +1268,9 @@
priv->hw->dma->rx_watchdog(priv->ioaddr, MAX_DMA_RIWT);
}
+ if (priv->pcs && priv->hw->mac->ctrl_ane)
+ priv->hw->mac->ctrl_ane(priv->ioaddr, 0);
+
napi_enable(&priv->napi);
netif_start_queue(dev);
@@ -2225,12 +2254,16 @@
else
priv->clk_csr = priv->plat->clk_csr;
- /* MDIO bus Registration */
- ret = stmmac_mdio_register(ndev);
- if (ret < 0) {
- pr_debug("%s: MDIO bus (id: %d) registration failed",
- __func__, priv->plat->bus_id);
- goto error_mdio_register;
+ stmmac_check_pcs_mode(priv);
+
+ if (!priv->pcs) {
+ /* MDIO bus Registration */
+ ret = stmmac_mdio_register(ndev);
+ if (ret < 0) {
+ pr_debug("%s: MDIO bus (id: %d) registration failed",
+ __func__, priv->plat->bus_id);
+ goto error_mdio_register;
+ }
}
return priv;
@@ -2263,7 +2296,8 @@
priv->hw->dma->stop_tx(priv->ioaddr);
stmmac_set_mac(priv->ioaddr, false);
- stmmac_mdio_unregister(ndev);
+ if (!priv->pcs)
+ stmmac_mdio_unregister(ndev);
netif_carrier_off(ndev);
unregister_netdev(ndev);
free_netdev(ndev);