Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 7b4e8a7..1df9d4c 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1269,10 +1269,6 @@
Recommended properties:
- - linux,network-index : This is the intended "index" of this
- network device. This is used by the bootwrapper to interpret
- MAC addresses passed by the firmware when no information other
- than indices is available to associate an address with a device.
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
"tbi", or "rtbi". This property is only really needed if the connection
@@ -1667,10 +1663,6 @@
- phy-handle : The phandle for the PHY connected to this controller.
Recommended properties:
- - linux,network-index : This is the intended "index" of this
- network device. This is used by the bootwrapper to interpret
- MAC addresses passed by the firmware when no information other
- than indices is available to associate an address with a device.
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
@@ -1995,7 +1987,6 @@
interrupts = <20 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY0>;
- linux,network-index = <0>;
fsl,cpm-command = <12000300>;
};
@@ -2217,12 +2208,6 @@
EMAC, that is the content of the current (bogus) "phy-port"
property.
- Recommended properties:
- - linux,network-index : This is the intended "index" of this
- network device. This is used by the bootwrapper to interpret
- MAC addresses passed by the firmware when no information other
- than indices is available to associate an address with a device.
-
Optional properties:
- phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
a search is performed.
@@ -2246,7 +2231,6 @@
Example:
EMAC0: ethernet@40000800 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 3651355..f43d82d 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -501,6 +501,9 @@
bool
select PPC_INDIRECT_PCI
+config 4xx_SOC
+ bool
+
# Yes MCA RS/6000s exist but Linux-PPC does not currently support any
config MCA
bool
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index a5528ab..73f3fd8 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -64,7 +64,7 @@
cuboot-bamboo.c cuboot-mpc7448hpc2.c cuboot-taishan.c \
fixed-head.S ep88xc.c ep405.c \
cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c \
- cuboot-warp.c cuboot-85xx-cpm2.c
+ cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -216,6 +216,7 @@
image-$(CONFIG_TAISHAN) += cuImage.taishan
image-$(CONFIG_KATMAI) += cuImage.katmai
image-$(CONFIG_WARP) += cuImage.warp
+image-$(CONFIG_YOSEMITE) += cuImage.yosemite
# Board ports in arch/powerpc/platform/8xx/Kconfig
image-$(CONFIG_PPC_MPC86XADS) += cuImage.mpc866ads
diff --git a/arch/powerpc/boot/bamboo.c b/arch/powerpc/boot/bamboo.c
index 54b33f1..b82cacb 100644
--- a/arch/powerpc/boot/bamboo.c
+++ b/arch/powerpc/boot/bamboo.c
@@ -33,7 +33,8 @@
ibm440ep_fixup_clocks(sysclk, 11059200, 25000000);
ibm4xx_sdram_fixup_memsize();
ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
- dt_fixup_mac_addresses(bamboo_mac0, bamboo_mac1);
+ dt_fixup_mac_address_by_alias("ethernet0", bamboo_mac0);
+ dt_fixup_mac_address_by_alias("ethernet1", bamboo_mac1);
}
void bamboo_init(void *mac0, void *mac1)
diff --git a/arch/powerpc/boot/cuboot-rainier.c b/arch/powerpc/boot/cuboot-rainier.c
index cf452b6..0a3fdde 100644
--- a/arch/powerpc/boot/cuboot-rainier.c
+++ b/arch/powerpc/boot/cuboot-rainier.c
@@ -42,7 +42,8 @@
ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
ibm4xx_denali_fixup_memsize();
- dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
}
void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
diff --git a/arch/powerpc/boot/cuboot-sequoia.c b/arch/powerpc/boot/cuboot-sequoia.c
index f555575..caf8f2e 100644
--- a/arch/powerpc/boot/cuboot-sequoia.c
+++ b/arch/powerpc/boot/cuboot-sequoia.c
@@ -42,7 +42,8 @@
ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
ibm4xx_denali_fixup_memsize();
- dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
}
void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
diff --git a/arch/powerpc/boot/cuboot-taishan.c b/arch/powerpc/boot/cuboot-taishan.c
index b55b804..9bc906a 100644
--- a/arch/powerpc/boot/cuboot-taishan.c
+++ b/arch/powerpc/boot/cuboot-taishan.c
@@ -40,7 +40,8 @@
ibm4xx_sdram_fixup_memsize();
- dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
}
diff --git a/arch/powerpc/boot/cuboot-warp.c b/arch/powerpc/boot/cuboot-warp.c
index 3db93e8..eb108a8 100644
--- a/arch/powerpc/boot/cuboot-warp.c
+++ b/arch/powerpc/boot/cuboot-warp.c
@@ -24,7 +24,7 @@
ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
ibm4xx_sdram_fixup_memsize();
ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
- dt_fixup_mac_addresses(&bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
}
diff --git a/arch/powerpc/boot/cuboot-yosemite.c b/arch/powerpc/boot/cuboot-yosemite.c
new file mode 100644
index 0000000..cc6e338
--- /dev/null
+++ b/arch/powerpc/boot/cuboot-yosemite.c
@@ -0,0 +1,44 @@
+/*
+ * Old U-boot compatibility for Yosemite
+ *
+ * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Copyright 2008 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "4xx.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void yosemite_fixups(void)
+{
+ unsigned long sysclk = 66666666;
+
+ ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
+ ibm4xx_sdram_fixup_memsize();
+ ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+ platform_ops.fixups = yosemite_fixups;
+ platform_ops.exit = ibm44x_dbcr_reset;
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
diff --git a/arch/powerpc/boot/dts/bamboo.dts b/arch/powerpc/boot/dts/bamboo.dts
index 7dc37c9..ba2521b 100644
--- a/arch/powerpc/boot/dts/bamboo.dts
+++ b/arch/powerpc/boot/dts/bamboo.dts
@@ -204,7 +204,6 @@
};
EMAC0: ethernet@ef600e00 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
@@ -225,7 +224,6 @@
};
EMAC1: ethernet@ef600f00 {
- linux,network-index = <1>;
device_type = "network";
compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
diff --git a/arch/powerpc/boot/dts/canyonlands.dts b/arch/powerpc/boot/dts/canyonlands.dts
new file mode 100644
index 0000000..657f2b4
--- /dev/null
+++ b/arch/powerpc/boot/dts/canyonlands.dts
@@ -0,0 +1,391 @@
+/*
+ * Device Tree Source for AMCC Canyonlands (460EX)
+ *
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr@denx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "amcc,canyonlands";
+ compatible = "amcc,canyonlands";
+ dcr-parent = <&/cpus/cpu@0>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,460EX";
+ reg = <0>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ timebase-frequency = <0>; /* Filled in by U-Boot */
+ i-cache-line-size = <20>;
+ d-cache-line-size = <20>;
+ i-cache-size = <8000>;
+ d-cache-size = <8000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0 0>; /* Filled in by U-Boot */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0c0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0d0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <1e 4 1f 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC2: interrupt-controller2 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <2>;
+ dcr-reg = <0e0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <a 4 b 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC3: interrupt-controller3 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <3>;
+ dcr-reg = <0f0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <10 4 11 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-460ex";
+ dcr-reg = <00e 002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-460ex";
+ dcr-reg = <00c 002>;
+ };
+
+ plb {
+ compatible = "ibm,plb-460ex", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-460ex", "ibm,sdram-405gp";
+ dcr-reg = <010 2>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-460ex", "ibm,mcmal2";
+ dcr-reg = <180 62>;
+ num-tx-chans = <2>;
+ num-rx-chans = <10>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-parent = <&UIC2>;
+ interrupts = < /*TXEOB*/ 6 4
+ /*RXEOB*/ 7 4
+ /*SERR*/ 3 4
+ /*TXDE*/ 4 4
+ /*RXDE*/ 5 4>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-460ex", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <b0000000 4 b0000000 50000000>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-460ex", "ibm,ebc";
+ dcr-reg = <012 2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ interrupts = <6 4>;
+ interrupt-parent = <&UIC1>;
+ };
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600300 8>;
+ virtual-reg = <ef600300>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1 4>;
+ };
+
+ UART1: serial@ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600400 8>;
+ virtual-reg = <ef600400>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC0>;
+ interrupts = <1 4>;
+ };
+
+ UART2: serial@ef600500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600500 8>;
+ virtual-reg = <ef600500>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1d 4>;
+ };
+
+ UART3: serial@ef600600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600600 8>;
+ virtual-reg = <ef600600>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1e 4>;
+ };
+
+ IIC0: i2c@ef600700 {
+ compatible = "ibm,iic-460ex", "ibm,iic";
+ reg = <ef600700 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <2 4>;
+ };
+
+ IIC1: i2c@ef600800 {
+ compatible = "ibm,iic-460ex", "ibm,iic";
+ reg = <ef600800 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <3 4>;
+ };
+
+ ZMII0: emac-zmii@ef600d00 {
+ compatible = "ibm,zmii-460ex", "ibm,zmii";
+ reg = <ef600d00 c>;
+ };
+
+ RGMII0: emac-rgmii@ef601500 {
+ compatible = "ibm,rgmii-460ex", "ibm,rgmii";
+ reg = <ef601500 8>;
+ has-mdio;
+ };
+
+ EMAC0: ethernet@ef600e00 {
+ device_type = "network";
+ compatible = "ibm,emac-460ex", "ibm,emac4";
+ interrupt-parent = <&EMAC0>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 10 4
+ /*Wake*/ 1 &UIC2 14 4>;
+ reg = <ef600e00 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <0>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ EMAC1: ethernet@ef600f00 {
+ device_type = "network";
+ compatible = "ibm,emac-460ex", "ibm,emac4";
+ interrupt-parent = <&EMAC1>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 11 4
+ /*Wake*/ 1 &UIC2 15 4>;
+ reg = <ef600f00 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <1>;
+ mal-rx-channel = <8>;
+ cell-index = <1>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <1>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <1>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+ };
+
+ PCIX0: pci@c0ec00000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pcix-460ex", "ibm,plb-pcix";
+ primary;
+ large-inbound-windows;
+ enable-msi-hole;
+ reg = <c 0ec00000 8 /* Config space access */
+ 0 0 0 /* no IACK cycles */
+ c 0ed00000 4 /* Special cycles */
+ c 0ec80000 100 /* Internal registers */
+ c 0ec80100 fc>; /* Internal messaging registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000d 80000000 0 80000000
+ 01000000 0 00000000 0000000c 08000000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 0 to 0x3f */
+ bus-range = <0 3f>;
+
+ /* All PCI interrupts are routed to ext IRQ 2 -> UIC1-0 */
+ interrupt-map-mask = <0000 0 0 0>;
+ interrupt-map = < 0000 0 0 0 &UIC1 0 8 >;
+ };
+
+ PCIE0: pciex@d00000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
+ primary;
+ port = <0>; /* port number */
+ reg = <d 00000000 20000000 /* Config space access */
+ c 08010000 00001000>; /* Registers */
+ dcr-reg = <100 020>;
+ sdr-base = <300>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 00000000 0 80000000
+ 01000000 0 00000000 0000000f 80000000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 40 to 0x7f */
+ bus-range = <40 7f>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 1 &UIC3 c 4 /* swizzled int A */
+ 0000 0 0 2 &UIC3 d 4 /* swizzled int B */
+ 0000 0 0 3 &UIC3 e 4 /* swizzled int C */
+ 0000 0 0 4 &UIC3 f 4 /* swizzled int D */>;
+ };
+
+ PCIE1: pciex@d20000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
+ primary;
+ port = <1>; /* port number */
+ reg = <d 20000000 20000000 /* Config space access */
+ c 08011000 00001000>; /* Registers */
+ dcr-reg = <120 020>;
+ sdr-base = <340>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 80000000 0 80000000
+ 01000000 0 00000000 0000000f 80010000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 80 to 0xbf */
+ bus-range = <80 bf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 1 &UIC3 10 4 /* swizzled int A */
+ 0000 0 0 2 &UIC3 11 4 /* swizzled int B */
+ 0000 0 0 3 &UIC3 12 4 /* swizzled int C */
+ 0000 0 0 4 &UIC3 13 4 /* swizzled int D */>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/ebony.dts b/arch/powerpc/boot/dts/ebony.dts
index 0b000cb..5079dc8 100644
--- a/arch/powerpc/boot/dts/ebony.dts
+++ b/arch/powerpc/boot/dts/ebony.dts
@@ -241,7 +241,6 @@
};
EMAC0: ethernet@40000800 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
@@ -261,7 +260,6 @@
zmii-channel = <0>;
};
EMAC1: ethernet@40000900 {
- linux,network-index = <1>;
device_type = "network";
compatible = "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
diff --git a/arch/powerpc/boot/dts/glacier.dts b/arch/powerpc/boot/dts/glacier.dts
new file mode 100644
index 0000000..7a7c9bf
--- /dev/null
+++ b/arch/powerpc/boot/dts/glacier.dts
@@ -0,0 +1,464 @@
+/*
+ * Device Tree Source for AMCC Glacier (460GT)
+ *
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr@denx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "amcc,glacier";
+ compatible = "amcc,glacier", "amcc,canyonlands";
+ dcr-parent = <&/cpus/cpu@0>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ ethernet2 = &EMAC2;
+ ethernet3 = &EMAC3;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,460GT";
+ reg = <0>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ timebase-frequency = <0>; /* Filled in by U-Boot */
+ i-cache-line-size = <20>;
+ d-cache-line-size = <20>;
+ i-cache-size = <8000>;
+ d-cache-size = <8000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0 0>; /* Filled in by U-Boot */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-460gt","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0c0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-460gt","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0d0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <1e 4 1f 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC2: interrupt-controller2 {
+ compatible = "ibm,uic-460gt","ibm,uic";
+ interrupt-controller;
+ cell-index = <2>;
+ dcr-reg = <0e0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <a 4 b 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC3: interrupt-controller3 {
+ compatible = "ibm,uic-460gt","ibm,uic";
+ interrupt-controller;
+ cell-index = <3>;
+ dcr-reg = <0f0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <10 4 11 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-460gt";
+ dcr-reg = <00e 002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-460gt";
+ dcr-reg = <00c 002>;
+ };
+
+ plb {
+ compatible = "ibm,plb-460gt", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-460gt", "ibm,sdram-405gp";
+ dcr-reg = <010 2>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-460gt", "ibm,mcmal2";
+ dcr-reg = <180 62>;
+ num-tx-chans = <4>;
+ num-rx-chans = <20>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-parent = <&UIC2>;
+ interrupts = < /*TXEOB*/ 6 4
+ /*RXEOB*/ 7 4
+ /*SERR*/ 3 4
+ /*TXDE*/ 4 4
+ /*RXDE*/ 5 4>;
+ desc-base-addr-high = <8>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-460gt", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <b0000000 4 b0000000 50000000>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-460gt", "ibm,ebc";
+ dcr-reg = <012 2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ interrupts = <6 4>;
+ interrupt-parent = <&UIC1>;
+ };
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600300 8>;
+ virtual-reg = <ef600300>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1 4>;
+ };
+
+ UART1: serial@ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600400 8>;
+ virtual-reg = <ef600400>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC0>;
+ interrupts = <1 4>;
+ };
+
+ UART2: serial@ef600500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600500 8>;
+ virtual-reg = <ef600500>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1d 4>;
+ };
+
+ UART3: serial@ef600600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600600 8>;
+ virtual-reg = <ef600600>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <1e 4>;
+ };
+
+ IIC0: i2c@ef600700 {
+ compatible = "ibm,iic-460gt", "ibm,iic";
+ reg = <ef600700 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <2 4>;
+ };
+
+ IIC1: i2c@ef600800 {
+ compatible = "ibm,iic-460gt", "ibm,iic";
+ reg = <ef600800 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <3 4>;
+ };
+
+ ZMII0: emac-zmii@ef600d00 {
+ compatible = "ibm,zmii-460gt", "ibm,zmii";
+ reg = <ef600d00 c>;
+ };
+
+ RGMII0: emac-rgmii@ef601500 {
+ compatible = "ibm,rgmii-460gt", "ibm,rgmii";
+ reg = <ef601500 8>;
+ has-mdio;
+ };
+
+ RGMII1: emac-rgmii@ef601600 {
+ compatible = "ibm,rgmii-460gt", "ibm,rgmii";
+ reg = <ef601600 8>;
+ has-mdio;
+ };
+
+ TAH0: emac-tah@ef601350 {
+ compatible = "ibm,tah-460gt", "ibm,tah";
+ reg = <ef601350 30>;
+ };
+
+ TAH1: emac-tah@ef601450 {
+ compatible = "ibm,tah-460gt", "ibm,tah";
+ reg = <ef601450 30>;
+ };
+
+ EMAC0: ethernet@ef600e00 {
+ device_type = "network";
+ compatible = "ibm,emac-460gt", "ibm,emac4";
+ interrupt-parent = <&EMAC0>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 10 4
+ /*Wake*/ 1 &UIC2 14 4>;
+ reg = <ef600e00 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ EMAC1: ethernet@ef600f00 {
+ device_type = "network";
+ compatible = "ibm,emac-460gt", "ibm,emac4";
+ interrupt-parent = <&EMAC1>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 11 4
+ /*Wake*/ 1 &UIC2 15 4>;
+ reg = <ef600f00 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <1>;
+ mal-rx-channel = <8>;
+ cell-index = <1>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <1>;
+ tah-device = <&TAH1>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ EMAC2: ethernet@ef601100 {
+ device_type = "network";
+ compatible = "ibm,emac-460gt", "ibm,emac4";
+ interrupt-parent = <&EMAC2>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 12 4
+ /*Wake*/ 1 &UIC2 16 4>;
+ reg = <ef601100 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <2>;
+ mal-rx-channel = <10>;
+ cell-index = <2>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ rgmii-device = <&RGMII1>;
+ rgmii-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+
+ EMAC3: ethernet@ef601200 {
+ device_type = "network";
+ compatible = "ibm,emac-460gt", "ibm,emac4";
+ interrupt-parent = <&EMAC3>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0 &UIC2 13 4
+ /*Wake*/ 1 &UIC2 17 4>;
+ reg = <ef601200 70>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <3>;
+ mal-rx-channel = <18>;
+ cell-index = <3>;
+ max-frame-size = <2328>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rgmii";
+ phy-map = <00000000>;
+ rgmii-device = <&RGMII1>;
+ rgmii-channel = <1>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+ };
+
+ PCIX0: pci@c0ec00000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pcix-460gt", "ibm,plb-pcix";
+ primary;
+ large-inbound-windows;
+ enable-msi-hole;
+ reg = <c 0ec00000 8 /* Config space access */
+ 0 0 0 /* no IACK cycles */
+ c 0ed00000 4 /* Special cycles */
+ c 0ec80000 100 /* Internal registers */
+ c 0ec80100 fc>; /* Internal messaging registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000d 80000000 0 80000000
+ 01000000 0 00000000 0000000c 08000000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 0 to 0x3f */
+ bus-range = <0 3f>;
+
+ /* All PCI interrupts are routed to ext IRQ 2 -> UIC1-0 */
+ interrupt-map-mask = <0000 0 0 0>;
+ interrupt-map = < 0000 0 0 0 &UIC1 0 8 >;
+ };
+
+ PCIE0: pciex@d00000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
+ primary;
+ port = <0>; /* port number */
+ reg = <d 00000000 20000000 /* Config space access */
+ c 08010000 00001000>; /* Registers */
+ dcr-reg = <100 020>;
+ sdr-base = <300>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 00000000 0 80000000
+ 01000000 0 00000000 0000000f 80000000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 40 to 0x7f */
+ bus-range = <40 7f>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 1 &UIC3 c 4 /* swizzled int A */
+ 0000 0 0 2 &UIC3 d 4 /* swizzled int B */
+ 0000 0 0 3 &UIC3 e 4 /* swizzled int C */
+ 0000 0 0 4 &UIC3 f 4 /* swizzled int D */>;
+ };
+
+ PCIE1: pciex@d20000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
+ primary;
+ port = <1>; /* port number */
+ reg = <d 20000000 20000000 /* Config space access */
+ c 08011000 00001000>; /* Registers */
+ dcr-reg = <120 020>;
+ sdr-base = <340>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 80000000 0 80000000
+ 01000000 0 00000000 0000000f 80010000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 80 to 0xbf */
+ bus-range = <80 bf>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 1 &UIC3 10 4 /* swizzled int A */
+ 0000 0 0 2 &UIC3 11 4 /* swizzled int B */
+ 0000 0 0 3 &UIC3 12 4 /* swizzled int C */
+ 0000 0 0 4 &UIC3 13 4 /* swizzled int D */>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/haleakala.dts b/arch/powerpc/boot/dts/haleakala.dts
index ae68fef..02e4ba3 100644
--- a/arch/powerpc/boot/dts/haleakala.dts
+++ b/arch/powerpc/boot/dts/haleakala.dts
@@ -12,7 +12,7 @@
#address-cells = <1>;
#size-cells = <1>;
model = "amcc,haleakala";
- compatible = "amcc,kilauea";
+ compatible = "amcc,haleakala", "amcc,kilauea";
dcr-parent = <&/cpus/cpu@0>;
aliases {
diff --git a/arch/powerpc/boot/dts/rainier.dts b/arch/powerpc/boot/dts/rainier.dts
index f947c75..9f6f58b 100644
--- a/arch/powerpc/boot/dts/rainier.dts
+++ b/arch/powerpc/boot/dts/rainier.dts
@@ -254,7 +254,6 @@
};
EMAC0: ethernet@ef600e00 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440grx", "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC0>;
@@ -284,7 +283,6 @@
};
EMAC1: ethernet@ef600f00 {
- linux,network-index = <1>;
device_type = "network";
compatible = "ibm,emac-440grx", "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC1>;
diff --git a/arch/powerpc/boot/dts/sequoia.dts b/arch/powerpc/boot/dts/sequoia.dts
index 8db9515..675026b 100644
--- a/arch/powerpc/boot/dts/sequoia.dts
+++ b/arch/powerpc/boot/dts/sequoia.dts
@@ -269,7 +269,6 @@
};
EMAC0: ethernet@ef600e00 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC0>;
@@ -299,7 +298,6 @@
};
EMAC1: ethernet@ef600f00 {
- linux,network-index = <1>;
device_type = "network";
compatible = "ibm,emac-440epx", "ibm,emac4";
interrupt-parent = <&EMAC1>;
diff --git a/arch/powerpc/boot/dts/taishan.dts b/arch/powerpc/boot/dts/taishan.dts
index 8278068..96d033d 100644
--- a/arch/powerpc/boot/dts/taishan.dts
+++ b/arch/powerpc/boot/dts/taishan.dts
@@ -104,6 +104,16 @@
// FIXME: anything else?
};
+ L2C0: l2c {
+ compatible = "ibm,l2-cache-440gx", "ibm,l2-cache";
+ dcr-reg = <20 8 /* Internal SRAM DCR's */
+ 30 8>; /* L2 cache DCR's */
+ cache-line-size = <20>; /* 32 bytes */
+ cache-size = <40000>; /* L2, 256K */
+ interrupt-parent = <&UIC2>;
+ interrupts = <17 1>;
+ };
+
plb {
compatible = "ibm,plb-440gx", "ibm,plb4";
#address-cells = <2>;
@@ -232,10 +242,18 @@
reg = <40000790 8>;
};
+ TAH0: emac-tah@40000b50 {
+ compatible = "ibm,tah-440gx", "ibm,tah";
+ reg = <40000b50 30>;
+ };
+
+ TAH1: emac-tah@40000d50 {
+ compatible = "ibm,tah-440gx", "ibm,tah";
+ reg = <40000d50 30>;
+ };
EMAC0: ethernet@40000800 {
unused = <1>;
- linux,network-index = <2>;
device_type = "network";
compatible = "ibm,emac-440gx", "ibm,emac4";
interrupt-parent = <&UIC1>;
@@ -256,7 +274,6 @@
};
EMAC1: ethernet@40000900 {
unused = <1>;
- linux,network-index = <3>;
device_type = "network";
compatible = "ibm,emac-440gx", "ibm,emac4";
interrupt-parent = <&UIC1>;
@@ -277,7 +294,6 @@
};
EMAC2: ethernet@40000c00 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440gx", "ibm,emac4";
interrupt-parent = <&UIC2>;
@@ -297,10 +313,11 @@
rgmii-channel = <0>;
zmii-device = <&ZMII0>;
zmii-channel = <2>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
};
EMAC3: ethernet@40000e00 {
- linux,network-index = <1>;
device_type = "network";
compatible = "ibm,emac-440gx", "ibm,emac4";
interrupt-parent = <&UIC2>;
@@ -320,6 +337,8 @@
rgmii-channel = <1>;
zmii-device = <&ZMII0>;
zmii-channel = <3>;
+ tah-device = <&TAH1>;
+ tah-channel = <0>;
};
diff --git a/arch/powerpc/boot/dts/walnut.dts b/arch/powerpc/boot/dts/walnut.dts
index dcc21b0..a328607 100644
--- a/arch/powerpc/boot/dts/walnut.dts
+++ b/arch/powerpc/boot/dts/walnut.dts
@@ -125,7 +125,6 @@
};
EMAC: ethernet@ef600800 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-405gp", "ibm,emac";
interrupt-parent = <&UIC0>;
diff --git a/arch/powerpc/boot/dts/warp.dts b/arch/powerpc/boot/dts/warp.dts
index dc1499d..b04a52e 100644
--- a/arch/powerpc/boot/dts/warp.dts
+++ b/arch/powerpc/boot/dts/warp.dts
@@ -204,7 +204,6 @@
};
EMAC0: ethernet@ef600e00 {
- linux,network-index = <0>;
device_type = "network";
compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
interrupt-parent = <&UIC1>;
diff --git a/arch/powerpc/boot/dts/yosemite.dts b/arch/powerpc/boot/dts/yosemite.dts
new file mode 100644
index 0000000..0d6d332
--- /dev/null
+++ b/arch/powerpc/boot/dts/yosemite.dts
@@ -0,0 +1,304 @@
+/*
+ * Device Tree Source for AMCC Yosemite
+ *
+ * Copyright 2008 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "amcc,yosemite";
+ compatible = "amcc,yosemite","amcc,bamboo";
+ dcr-parent = <&/cpus/cpu@0>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ serial2 = &UART2;
+ serial3 = &UART3;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,440EP";
+ reg = <0>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <20>;
+ d-cache-line-size = <20>;
+ i-cache-size = <8000>;
+ d-cache-size = <8000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0 0>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-440ep","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0c0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-440ep","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0d0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <1e 4 1f 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-440ep";
+ dcr-reg = <00e 002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-440ep";
+ dcr-reg = <00c 002>;
+ };
+
+ plb {
+ compatible = "ibm,plb-440ep", "ibm,plb-440gp", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-440ep", "ibm,sdram-405gp";
+ dcr-reg = <010 2>;
+ };
+
+ DMA0: dma {
+ compatible = "ibm,dma-440ep", "ibm,dma-440gp";
+ dcr-reg = <100 027>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-440ep", "ibm,mcmal-440gp", "ibm,mcmal";
+ dcr-reg = <180 62>;
+ num-tx-chans = <4>;
+ num-rx-chans = <2>;
+ interrupt-parent = <&MAL0>;
+ interrupts = <0 1 2 3 4>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+ /*RXEOB*/ 1 &UIC0 b 4
+ /*SERR*/ 2 &UIC1 0 4
+ /*TXDE*/ 3 &UIC1 1 4
+ /*RXDE*/ 4 &UIC1 2 4>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-440ep", "ibm,opb-440gp", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* Bamboo is oddball in the 44x world and doesn't use the ERPN
+ * bits.
+ */
+ ranges = <00000000 0 00000000 80000000
+ 80000000 0 80000000 80000000>;
+ interrupt-parent = <&UIC1>;
+ interrupts = <7 4>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-440ep", "ibm,ebc-440gp", "ibm,ebc";
+ dcr-reg = <012 2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ interrupts = <5 1>;
+ interrupt-parent = <&UIC1>;
+ };
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600300 8>;
+ virtual-reg = <ef600300>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <1c200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0 4>;
+ };
+
+ UART1: serial@ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600400 8>;
+ virtual-reg = <ef600400>;
+ clock-frequency = <0>;
+ current-speed = <0>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <1 4>;
+ };
+
+ UART2: serial@ef600500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600500 8>;
+ virtual-reg = <ef600500>;
+ clock-frequency = <0>;
+ current-speed = <0>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <3 4>;
+ status = "disabled";
+ };
+
+ UART3: serial@ef600600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <ef600600 8>;
+ virtual-reg = <ef600600>;
+ clock-frequency = <0>;
+ current-speed = <0>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <4 4>;
+ status = "disabled";
+ };
+
+ IIC0: i2c@ef600700 {
+ compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
+ reg = <ef600700 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <2 4>;
+ };
+
+ IIC1: i2c@ef600800 {
+ compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
+ reg = <ef600800 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <7 4>;
+ };
+
+ spi@ef600900 {
+ compatible = "amcc,spi-440ep";
+ reg = <ef600900 6>;
+ interrupts = <8 4>;
+ interrupt-parent = <&UIC0>;
+ };
+
+ ZMII0: emac-zmii@ef600d00 {
+ compatible = "ibm,zmii-440ep", "ibm,zmii-440gp", "ibm,zmii";
+ reg = <ef600d00 c>;
+ };
+
+ EMAC0: ethernet@ef600e00 {
+ device_type = "network";
+ compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1c 4 1d 4>;
+ reg = <ef600e00 70>;
+ local-mac-address = [000000000000];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0 1>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rmii";
+ phy-map = <00000000>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <0>;
+ };
+
+ EMAC1: ethernet@ef600f00 {
+ device_type = "network";
+ compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1e 4 1f 4>;
+ reg = <ef600f00 70>;
+ local-mac-address = [000000000000];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <2 3>;
+ mal-rx-channel = <1>;
+ cell-index = <1>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rmii";
+ phy-map = <00000000>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <1>;
+ };
+
+ usb@ef601000 {
+ compatible = "ohci-be";
+ reg = <ef601000 80>;
+ interrupts = <8 4 9 4>;
+ interrupt-parent = < &UIC1 >;
+ };
+ };
+
+ PCI0: pci@ec000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb440ep-pci", "ibm,plb-pci";
+ primary;
+ reg = <0 eec00000 8 /* Config space access */
+ 0 eed00000 4 /* IACK */
+ 0 eed00000 4 /* Special cycle */
+ 0 ef400000 40>; /* Internal registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed. Chip supports a second
+ * IO range but we don't use it for now
+ */
+ ranges = <02000000 0 a0000000 0 a0000000 0 20000000
+ 01000000 0 00000000 0 e8000000 0 00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* Bamboo has all 4 IRQ pins tied together per slot */
+ interrupt-map-mask = <f800 0 0 0>;
+ interrupt-map = <
+ /* IDSEL 1 */
+ 0800 0 0 0 &UIC0 1c 8
+
+ /* IDSEL 2 */
+ 1000 0 0 0 &UIC0 1b 8
+
+ /* IDSEL 3 */
+ 1800 0 0 0 &UIC0 1a 8
+
+ /* IDSEL 4 */
+ 2000 0 0 0 &UIC0 19 8
+ >;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@ef600300";
+ };
+};
diff --git a/arch/powerpc/boot/ebony.c b/arch/powerpc/boot/ebony.c
index f61364c..5532ab3 100644
--- a/arch/powerpc/boot/ebony.c
+++ b/arch/powerpc/boot/ebony.c
@@ -75,7 +75,8 @@
ibm440gp_fixup_clocks(sysclk, 6 * 1843200);
ibm4xx_sdram_fixup_memsize();
- dt_fixup_mac_addresses(ebony_mac0, ebony_mac1);
+ dt_fixup_mac_address_by_alias("ethernet0", ebony_mac0);
+ dt_fixup_mac_address_by_alias("ethernet1", ebony_mac1);
ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
ebony_flashsel_fixup();
}
diff --git a/arch/powerpc/boot/treeboot-walnut.c b/arch/powerpc/boot/treeboot-walnut.c
index 472e366..097974e 100644
--- a/arch/powerpc/boot/treeboot-walnut.c
+++ b/arch/powerpc/boot/treeboot-walnut.c
@@ -68,7 +68,7 @@
ibm4xx_quiesce_eth((u32 *)0xef600800, NULL);
ibm4xx_fixup_ebc_ranges("/plb/ebc");
walnut_flashsel_fixup();
- dt_fixup_mac_addresses((u8 *) WALNUT_OPENBIOS_MAC_OFF);
+ dt_fixup_mac_address_by_alias("ethernet0", (u8 *) WALNUT_OPENBIOS_MAC_OFF);
}
void platform_init(void)
diff --git a/arch/powerpc/configs/canyonlands_defconfig b/arch/powerpc/configs/canyonlands_defconfig
new file mode 100644
index 0000000..a3b763c
--- /dev/null
+++ b/arch/powerpc/configs/canyonlands_defconfig
@@ -0,0 +1,721 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.25-rc1
+# Thu Feb 21 14:29:28 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_FAIR_GROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+# CONFIG_LOGBUFFER is not set
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_PPC4xx_PCI_EXPRESS=y
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC512x is not set
+# CONFIG_PPC_MPC5121 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_BAMBOO is not set
+# CONFIG_EBONY is not set
+# CONFIG_SEQUOIA is not set
+# CONFIG_TAISHAN is not set
+# CONFIG_KATMAI is not set
+# CONFIG_RAINIER is not set
+# CONFIG_WARP is not set
+CONFIG_CANYONLANDS=y
+CONFIG_460EX=y
+# CONFIG_IPIC is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_RCU_TRACE=y
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_IOMMU_HELPER is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_HAS_WALK_MEMORY=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE=""
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0xc0000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+# CONFIG_MII is not set
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=256
+CONFIG_IBM_NEW_EMAC_TXB=256
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+CONFIG_IBM_NEW_EMAC_RGMII=y
+CONFIG_IBM_NEW_EMAC_TAH=y
+CONFIG_IBM_NEW_EMAC_EMAC4=y
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+CONFIG_DEBUGGER=y
+# CONFIG_KGDB is not set
+# CONFIG_XMON is not set
+# CONFIG_VIRQ_DEBUG is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_PPC_CLOCK is not set
diff --git a/arch/powerpc/kernel/cpu_setup_44x.S b/arch/powerpc/kernel/cpu_setup_44x.S
index 6250443..5465e8d 100644
--- a/arch/powerpc/kernel/cpu_setup_44x.S
+++ b/arch/powerpc/kernel/cpu_setup_44x.S
@@ -3,7 +3,7 @@
* Valentine Barshak <vbarshak@ru.mvista.com>
* MontaVista Software, Inc (c) 2007
*
- * Based on cpu_setup_6xx code by
+ * Based on cpu_setup_6xx code by
* Benjamin Herrenschmidt <benh@kernel.crashing.org>
*
* This program is free software; you can redistribute it and/or
@@ -32,6 +32,9 @@
bl __fixup_440A_mcheck
mtlr r4
blr
+_GLOBAL(__setup_cpu_460ex)
+_GLOBAL(__setup_cpu_460gt)
+ b __init_fpu_44x
_GLOBAL(__setup_cpu_440gx)
_GLOBAL(__setup_cpu_440spe)
b __fixup_440A_mcheck
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index 2a8f5cc..26ffb44 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -36,6 +36,8 @@
extern void __setup_cpu_440gx(unsigned long offset, struct cpu_spec* spec);
extern void __setup_cpu_440grx(unsigned long offset, struct cpu_spec* spec);
extern void __setup_cpu_440spe(unsigned long offset, struct cpu_spec* spec);
+extern void __setup_cpu_460ex(unsigned long offset, struct cpu_spec* spec);
+extern void __setup_cpu_460gt(unsigned long offset, struct cpu_spec* spec);
extern void __setup_cpu_603(unsigned long offset, struct cpu_spec* spec);
extern void __setup_cpu_604(unsigned long offset, struct cpu_spec* spec);
extern void __setup_cpu_750(unsigned long offset, struct cpu_spec* spec);
@@ -1397,6 +1399,30 @@
.machine_check = machine_check_440A,
.platform = "ppc440",
},
+ { /* 460EX */
+ .pvr_mask = 0xffff0002,
+ .pvr_value = 0x13020002,
+ .cpu_name = "460EX",
+ .cpu_features = CPU_FTRS_44X,
+ .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+ .icache_bsize = 32,
+ .dcache_bsize = 32,
+ .cpu_setup = __setup_cpu_460ex,
+ .machine_check = machine_check_440A,
+ .platform = "ppc440",
+ },
+ { /* 460GT */
+ .pvr_mask = 0xffff0002,
+ .pvr_value = 0x13020000,
+ .cpu_name = "460GT",
+ .cpu_features = CPU_FTRS_44X,
+ .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+ .icache_bsize = 32,
+ .dcache_bsize = 32,
+ .cpu_setup = __setup_cpu_460gt,
+ .machine_check = machine_check_440A,
+ .platform = "ppc440",
+ },
#endif /* CONFIG_44x */
#ifdef CONFIG_FSL_BOOKE
#ifdef CONFIG_E200
@@ -1512,7 +1538,7 @@
*t = *s;
*PTRRELOC(&cur_cpu_spec) = &the_cpu_spec;
#if defined(CONFIG_PPC64) || defined(CONFIG_BOOKE)
- /* ppc64 and booke expect identify_cpu to also call
+ /* ppc64 and booke expect identify_cpu to also call
* setup_cpu for that processor. I will consolidate
* that at a later time, for now, just use #ifdef.
* we also don't need to PTRRELOC the function pointer
diff --git a/arch/powerpc/platforms/44x/Kconfig b/arch/powerpc/platforms/44x/Kconfig
index 1bfb219..5fc28aa 100644
--- a/arch/powerpc/platforms/44x/Kconfig
+++ b/arch/powerpc/platforms/44x/Kconfig
@@ -67,6 +67,25 @@
See http://www.pikatechnologies.com/ and follow the "PIKA for Computer
Telephony Developers" link for more information.
+config CANYONLANDS
+ bool "Canyonlands"
+ depends on 44x
+ default n
+ select 460EX
+ select PCI
+ select PPC4xx_PCI_EXPRESS
+ help
+ This option enables support for the AMCC PPC460EX evaluation board.
+
+config YOSEMITE
+ bool "Yosemite"
+ depends on 44x
+ default n
+ select 440EP
+ select PCI
+ help
+ This option enables support for the AMCC PPC440EP evaluation board.
+
#config LUAN
# bool "Luan"
# depends on 44x
@@ -110,6 +129,7 @@
config 440GX
bool
+ select 4xx_SOC
select IBM_NEW_EMAC_EMAC4
select IBM_NEW_EMAC_RGMII
select IBM_NEW_EMAC_ZMII #test only
@@ -122,6 +142,14 @@
bool
select IBM_NEW_EMAC_EMAC4
+config 460EX
+ bool
+ select PPC_FPU
+ select IBM_NEW_EMAC_EMAC4
+ select IBM_NEW_EMAC_RGMII
+ select IBM_NEW_EMAC_ZMII
+ select IBM_NEW_EMAC_TAH
+
# 44x errata/workaround config symbols, selected by the CPU models above
config IBM440EP_ERR42
bool
diff --git a/arch/powerpc/platforms/44x/Makefile b/arch/powerpc/platforms/44x/Makefile
index 0864d4f..2320ae5 100644
--- a/arch/powerpc/platforms/44x/Makefile
+++ b/arch/powerpc/platforms/44x/Makefile
@@ -2,8 +2,10 @@
obj-$(CONFIG_EBONY) += ebony.o
obj-$(CONFIG_TAISHAN) += taishan.o
obj-$(CONFIG_BAMBOO) += bamboo.o
+obj-$(CONFIG_YOSEMITE) += bamboo.o
obj-$(CONFIG_SEQUOIA) += sequoia.o
obj-$(CONFIG_KATMAI) += katmai.o
obj-$(CONFIG_RAINIER) += rainier.o
obj-$(CONFIG_WARP) += warp.o
obj-$(CONFIG_WARP) += warp-nand.o
+obj-$(CONFIG_CANYONLANDS) += canyonlands.o
diff --git a/arch/powerpc/platforms/44x/canyonlands.c b/arch/powerpc/platforms/44x/canyonlands.c
new file mode 100644
index 0000000..dac5b32
--- /dev/null
+++ b/arch/powerpc/platforms/44x/canyonlands.c
@@ -0,0 +1,64 @@
+/*
+ * Canyonlands board specific routines
+ *
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr@denx.de>
+ *
+ * Based on the Katmai code by
+ * Benjamin Herrenschmidt <benh@kernel.crashing.org>
+ * Copyright 2007 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ * Copyright 2007 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/init.h>
+#include <linux/of_platform.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+#include <asm/pci-bridge.h>
+
+#include "44x.h"
+
+static __initdata struct of_device_id canyonlands_of_bus[] = {
+ { .compatible = "ibm,plb4", },
+ { .compatible = "ibm,opb", },
+ { .compatible = "ibm,ebc", },
+ {},
+};
+
+static int __init canyonlands_device_probe(void)
+{
+ of_platform_bus_probe(NULL, canyonlands_of_bus, NULL);
+
+ return 0;
+}
+machine_device_initcall(canyonlands, canyonlands_device_probe);
+
+static int __init canyonlands_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (!of_flat_dt_is_compatible(root, "amcc,canyonlands"))
+ return 0;
+
+ ppc_pci_flags = PPC_PCI_REASSIGN_ALL_RSRC;
+
+ return 1;
+}
+
+define_machine(canyonlands) {
+ .name = "Canyonlands",
+ .probe = canyonlands_probe,
+ .progress = udbg_progress,
+ .init_IRQ = uic_init_tree,
+ .get_irq = uic_get_irq,
+ .restart = ppc44x_reset_system,
+ .calibrate_decr = generic_calibrate_decr,
+};
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index 15f3e85..851a0be 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -27,6 +27,7 @@
obj-$(CONFIG_PPC_I8259) += i8259.o
obj-$(CONFIG_IPIC) += ipic.o
obj-$(CONFIG_4xx) += uic.o
+obj-$(CONFIG_4xx_SOC) += ppc4xx_soc.o
obj-$(CONFIG_XILINX_VIRTEX) += xilinx_intc.o
obj-$(CONFIG_OF_RTC) += of_rtc.o
ifeq ($(CONFIG_PCI),y)
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c
index 5abfcd1..6c925b7 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.c
+++ b/arch/powerpc/sysdev/ppc4xx_pci.c
@@ -527,6 +527,7 @@
*
* ibm,plb-pciex-440spe
* ibm,plb-pciex-405ex
+ * ibm,plb-pciex-460ex
*
* Anything else will be rejected for now as they are all subtly
* different unfortunately.
@@ -645,7 +646,7 @@
int time_out = 20;
/* Set PLL clock receiver to LVPECL */
- mtdcri(SDR0, PESDR0_PLLLCT1, mfdcri(SDR0, PESDR0_PLLLCT1) | 1 << 28);
+ dcri_clrset(SDR0, PESDR0_PLLLCT1, 0, 1 << 28);
/* Shouldn't we do all the calibration stuff etc... here ? */
if (ppc440spe_pciex_check_reset(np))
@@ -659,8 +660,7 @@
}
/* De-assert reset of PCIe PLL, wait for lock */
- mtdcri(SDR0, PESDR0_PLLLCT1,
- mfdcri(SDR0, PESDR0_PLLLCT1) & ~(1 << 24));
+ dcri_clrset(SDR0, PESDR0_PLLLCT1, 1 << 24, 0);
udelay(3);
while (time_out) {
@@ -712,9 +712,8 @@
mtdcri(SDR0, port->sdr_base + PESDRn_440SPE_HSSL7SET1,
0x35000000);
}
- val = mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET);
- mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET,
- (val & ~(1 << 24 | 1 << 16)) | 1 << 12);
+ dcri_clrset(SDR0, port->sdr_base + PESDRn_RCSSET,
+ (1 << 24) | (1 << 16), 1 << 12);
return 0;
}
@@ -775,6 +774,117 @@
.setup_utl = ppc440speB_pciex_init_utl,
};
+static int __init ppc460ex_pciex_core_init(struct device_node *np)
+{
+ /* Nothing to do, return 2 ports */
+ return 2;
+}
+
+static int ppc460ex_pciex_init_port_hw(struct ppc4xx_pciex_port *port)
+{
+ u32 val;
+ u32 utlset1;
+
+ if (port->endpoint) {
+ val = PTYPE_LEGACY_ENDPOINT << 20;
+ utlset1 = 0x20222222;
+ } else {
+ val = PTYPE_ROOT_PORT << 20;
+ utlset1 = 0x21222222;
+ }
+
+ if (port->index == 0) {
+ val |= LNKW_X1 << 12;
+ } else {
+ val |= LNKW_X4 << 12;
+ utlset1 |= 0x00101101;
+ }
+
+ mtdcri(SDR0, port->sdr_base + PESDRn_DLPSET, val);
+ mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET1, utlset1);
+ mtdcri(SDR0, port->sdr_base + PESDRn_UTLSET2, 0x01210000);
+
+ switch (port->index) {
+ case 0:
+ mtdcri(SDR0, PESDR0_460EX_L0CDRCTL, 0x00003230);
+ mtdcri(SDR0, PESDR0_460EX_L0DRV, 0x00000136);
+ mtdcri(SDR0, PESDR0_460EX_L0CLK, 0x00000006);
+
+ mtdcri(SDR0, PESDR0_460EX_PHY_CTL_RST,0x10000000);
+ break;
+
+ case 1:
+ mtdcri(SDR0, PESDR1_460EX_L0CDRCTL, 0x00003230);
+ mtdcri(SDR0, PESDR1_460EX_L1CDRCTL, 0x00003230);
+ mtdcri(SDR0, PESDR1_460EX_L2CDRCTL, 0x00003230);
+ mtdcri(SDR0, PESDR1_460EX_L3CDRCTL, 0x00003230);
+ mtdcri(SDR0, PESDR1_460EX_L0DRV, 0x00000136);
+ mtdcri(SDR0, PESDR1_460EX_L1DRV, 0x00000136);
+ mtdcri(SDR0, PESDR1_460EX_L2DRV, 0x00000136);
+ mtdcri(SDR0, PESDR1_460EX_L3DRV, 0x00000136);
+ mtdcri(SDR0, PESDR1_460EX_L0CLK, 0x00000006);
+ mtdcri(SDR0, PESDR1_460EX_L1CLK, 0x00000006);
+ mtdcri(SDR0, PESDR1_460EX_L2CLK, 0x00000006);
+ mtdcri(SDR0, PESDR1_460EX_L3CLK, 0x00000006);
+
+ mtdcri(SDR0, PESDR1_460EX_PHY_CTL_RST,0x10000000);
+ break;
+ }
+
+ mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET,
+ mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET) |
+ (PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTPYN));
+
+ /* Poll for PHY reset */
+ /* XXX FIXME add timeout */
+ switch (port->index) {
+ case 0:
+ while (!(mfdcri(SDR0, PESDR0_460EX_RSTSTA) & 0x1))
+ udelay(10);
+ break;
+ case 1:
+ while (!(mfdcri(SDR0, PESDR1_460EX_RSTSTA) & 0x1))
+ udelay(10);
+ break;
+ }
+
+ mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET,
+ (mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET) &
+ ~(PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTDL)) |
+ PESDRx_RCSSET_RSTPYN);
+
+ port->has_ibpre = 1;
+
+ return 0;
+}
+
+static int ppc460ex_pciex_init_utl(struct ppc4xx_pciex_port *port)
+{
+ dcr_write(port->dcrs, DCRO_PEGPL_SPECIAL, 0x0);
+
+ /*
+ * Set buffer allocations and then assert VRB and TXE.
+ */
+ out_be32(port->utl_base + PEUTL_PBCTL, 0x0800000c);
+ out_be32(port->utl_base + PEUTL_OUTTR, 0x08000000);
+ out_be32(port->utl_base + PEUTL_INTR, 0x02000000);
+ out_be32(port->utl_base + PEUTL_OPDBSZ, 0x04000000);
+ out_be32(port->utl_base + PEUTL_PBBSZ, 0x00000000);
+ out_be32(port->utl_base + PEUTL_IPHBSZ, 0x02000000);
+ out_be32(port->utl_base + PEUTL_IPDBSZ, 0x04000000);
+ out_be32(port->utl_base + PEUTL_RCIRQEN,0x00f00000);
+ out_be32(port->utl_base + PEUTL_PCTL, 0x80800066);
+
+ return 0;
+}
+
+static struct ppc4xx_pciex_hwops ppc460ex_pcie_hwops __initdata =
+{
+ .core_init = ppc460ex_pciex_core_init,
+ .port_init_hw = ppc460ex_pciex_init_port_hw,
+ .setup_utl = ppc460ex_pciex_init_utl,
+};
+
#endif /* CONFIG_44x */
#ifdef CONFIG_40x
@@ -896,6 +1006,8 @@
else
ppc4xx_pciex_hwops = &ppc440speB_pcie_hwops;
}
+ if (of_device_is_compatible(np, "ibm,plb-pciex-460ex"))
+ ppc4xx_pciex_hwops = &ppc460ex_pcie_hwops;
#endif /* CONFIG_44x */
#ifdef CONFIG_40x
if (of_device_is_compatible(np, "ibm,plb-pciex-405ex"))
@@ -1042,8 +1154,7 @@
port->link = 0;
}
- mtdcri(SDR0, port->sdr_base + PESDRn_RCSSET,
- mfdcri(SDR0, port->sdr_base + PESDRn_RCSSET) | 1 << 20);
+ dcri_clrset(SDR0, port->sdr_base + PESDRn_RCSSET, 0, 1 << 20);
msleep(100);
return 0;
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.h b/arch/powerpc/sysdev/ppc4xx_pci.h
index 1c07908..d04e40b 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.h
+++ b/arch/powerpc/sysdev/ppc4xx_pci.h
@@ -271,6 +271,59 @@
#define PESDR1_405EX_PHYSTA 0x044C
/*
+ * 460EX additional DCRs
+ */
+#define PESDR0_460EX_L0BIST 0x0308
+#define PESDR0_460EX_L0BISTSTS 0x0309
+#define PESDR0_460EX_L0CDRCTL 0x030A
+#define PESDR0_460EX_L0DRV 0x030B
+#define PESDR0_460EX_L0REC 0x030C
+#define PESDR0_460EX_L0LPB 0x030D
+#define PESDR0_460EX_L0CLK 0x030E
+#define PESDR0_460EX_PHY_CTL_RST 0x030F
+#define PESDR0_460EX_RSTSTA 0x0310
+#define PESDR0_460EX_OBS 0x0311
+#define PESDR0_460EX_L0ERRC 0x0320
+
+#define PESDR1_460EX_L0BIST 0x0348
+#define PESDR1_460EX_L1BIST 0x0349
+#define PESDR1_460EX_L2BIST 0x034A
+#define PESDR1_460EX_L3BIST 0x034B
+#define PESDR1_460EX_L0BISTSTS 0x034C
+#define PESDR1_460EX_L1BISTSTS 0x034D
+#define PESDR1_460EX_L2BISTSTS 0x034E
+#define PESDR1_460EX_L3BISTSTS 0x034F
+#define PESDR1_460EX_L0CDRCTL 0x0350
+#define PESDR1_460EX_L1CDRCTL 0x0351
+#define PESDR1_460EX_L2CDRCTL 0x0352
+#define PESDR1_460EX_L3CDRCTL 0x0353
+#define PESDR1_460EX_L0DRV 0x0354
+#define PESDR1_460EX_L1DRV 0x0355
+#define PESDR1_460EX_L2DRV 0x0356
+#define PESDR1_460EX_L3DRV 0x0357
+#define PESDR1_460EX_L0REC 0x0358
+#define PESDR1_460EX_L1REC 0x0359
+#define PESDR1_460EX_L2REC 0x035A
+#define PESDR1_460EX_L3REC 0x035B
+#define PESDR1_460EX_L0LPB 0x035C
+#define PESDR1_460EX_L1LPB 0x035D
+#define PESDR1_460EX_L2LPB 0x035E
+#define PESDR1_460EX_L3LPB 0x035F
+#define PESDR1_460EX_L0CLK 0x0360
+#define PESDR1_460EX_L1CLK 0x0361
+#define PESDR1_460EX_L2CLK 0x0362
+#define PESDR1_460EX_L3CLK 0x0363
+#define PESDR1_460EX_PHY_CTL_RST 0x0364
+#define PESDR1_460EX_RSTSTA 0x0365
+#define PESDR1_460EX_OBS 0x0366
+#define PESDR1_460EX_L0ERRC 0x0368
+#define PESDR1_460EX_L1ERRC 0x0369
+#define PESDR1_460EX_L2ERRC 0x036A
+#define PESDR1_460EX_L3ERRC 0x036B
+#define PESDR0_460EX_IHS1 0x036C
+#define PESDR0_460EX_IHS2 0x036D
+
+/*
* Of the above, some are common offsets from the base
*/
#define PESDRn_UTLSET1 0x00
@@ -353,6 +406,12 @@
#define PECFG_POM2LAL 0x390
#define PECFG_POM2LAH 0x394
+/* SDR Bit Mappings */
+#define PESDRx_RCSSET_HLDPLB 0x10000000
+#define PESDRx_RCSSET_RSTGU 0x01000000
+#define PESDRx_RCSSET_RDY 0x00100000
+#define PESDRx_RCSSET_RSTDL 0x00010000
+#define PESDRx_RCSSET_RSTPYN 0x00001000
enum
{
diff --git a/arch/powerpc/sysdev/ppc4xx_soc.c b/arch/powerpc/sysdev/ppc4xx_soc.c
new file mode 100644
index 0000000..4b8617e
--- /dev/null
+++ b/arch/powerpc/sysdev/ppc4xx_soc.c
@@ -0,0 +1,189 @@
+/*
+ * IBM/AMCC PPC4xx SoC setup code
+ *
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr@denx.de>
+ *
+ * L2 cache routines cloned from arch/ppc/syslib/ibm440gx_common.c which is:
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ * Copyright (c) 2003 - 2006 Zultys Technologies
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/of_platform.h>
+
+#include <asm/dcr.h>
+#include <asm/dcr-regs.h>
+
+static u32 dcrbase_l2c;
+
+/*
+ * L2-cache
+ */
+
+/* Issue L2C diagnostic command */
+static inline u32 l2c_diag(u32 addr)
+{
+ mtdcr(dcrbase_l2c + DCRN_L2C0_ADDR, addr);
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CMD, L2C_CMD_DIAG);
+ while (!(mfdcr(dcrbase_l2c + DCRN_L2C0_SR) & L2C_SR_CC))
+ ;
+
+ return mfdcr(dcrbase_l2c + DCRN_L2C0_DATA);
+}
+
+static irqreturn_t l2c_error_handler(int irq, void *dev)
+{
+ u32 sr = mfdcr(dcrbase_l2c + DCRN_L2C0_SR);
+
+ if (sr & L2C_SR_CPE) {
+ /* Read cache trapped address */
+ u32 addr = l2c_diag(0x42000000);
+ printk(KERN_EMERG "L2C: Cache Parity Error, addr[16:26] = 0x%08x\n",
+ addr);
+ }
+ if (sr & L2C_SR_TPE) {
+ /* Read tag trapped address */
+ u32 addr = l2c_diag(0x82000000) >> 16;
+ printk(KERN_EMERG "L2C: Tag Parity Error, addr[16:26] = 0x%08x\n",
+ addr);
+ }
+
+ /* Clear parity errors */
+ if (sr & (L2C_SR_CPE | L2C_SR_TPE)){
+ mtdcr(dcrbase_l2c + DCRN_L2C0_ADDR, 0);
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CMD, L2C_CMD_CCP | L2C_CMD_CTE);
+ } else {
+ printk(KERN_EMERG "L2C: LRU error\n");
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int __init ppc4xx_l2c_probe(void)
+{
+ struct device_node *np;
+ u32 r;
+ unsigned long flags;
+ int irq;
+ const u32 *dcrreg;
+ u32 dcrbase_isram;
+ int len;
+ const u32 *prop;
+ u32 l2_size;
+
+ np = of_find_compatible_node(NULL, NULL, "ibm,l2-cache");
+ if (!np)
+ return 0;
+
+ /* Get l2 cache size */
+ prop = of_get_property(np, "cache-size", NULL);
+ if (prop == NULL) {
+ printk(KERN_ERR "%s: Can't get cache-size!\n", np->full_name);
+ of_node_put(np);
+ return -ENODEV;
+ }
+ l2_size = prop[0];
+
+ /* Map DCRs */
+ dcrreg = of_get_property(np, "dcr-reg", &len);
+ if (!dcrreg || (len != 4 * sizeof(u32))) {
+ printk(KERN_ERR "%s: Can't get DCR register base !",
+ np->full_name);
+ of_node_put(np);
+ return -ENODEV;
+ }
+ dcrbase_isram = dcrreg[0];
+ dcrbase_l2c = dcrreg[2];
+
+ /* Get and map irq number from device tree */
+ irq = irq_of_parse_and_map(np, 0);
+ if (irq == NO_IRQ) {
+ printk(KERN_ERR "irq_of_parse_and_map failed\n");
+ of_node_put(np);
+ return -ENODEV;
+ }
+
+ /* Install error handler */
+ if (request_irq(irq, l2c_error_handler, IRQF_DISABLED, "L2C", 0) < 0) {
+ printk(KERN_ERR "Cannot install L2C error handler"
+ ", cache is not enabled\n");
+ of_node_put(np);
+ return -ENODEV;
+ }
+
+ local_irq_save(flags);
+ asm volatile ("sync" ::: "memory");
+
+ /* Disable SRAM */
+ mtdcr(dcrbase_isram + DCRN_SRAM0_DPC,
+ mfdcr(dcrbase_isram + DCRN_SRAM0_DPC) & ~SRAM_DPC_ENABLE);
+ mtdcr(dcrbase_isram + DCRN_SRAM0_SB0CR,
+ mfdcr(dcrbase_isram + DCRN_SRAM0_SB0CR) & ~SRAM_SBCR_BU_MASK);
+ mtdcr(dcrbase_isram + DCRN_SRAM0_SB1CR,
+ mfdcr(dcrbase_isram + DCRN_SRAM0_SB1CR) & ~SRAM_SBCR_BU_MASK);
+ mtdcr(dcrbase_isram + DCRN_SRAM0_SB2CR,
+ mfdcr(dcrbase_isram + DCRN_SRAM0_SB2CR) & ~SRAM_SBCR_BU_MASK);
+ mtdcr(dcrbase_isram + DCRN_SRAM0_SB3CR,
+ mfdcr(dcrbase_isram + DCRN_SRAM0_SB3CR) & ~SRAM_SBCR_BU_MASK);
+
+ /* Enable L2_MODE without ICU/DCU */
+ r = mfdcr(dcrbase_l2c + DCRN_L2C0_CFG) &
+ ~(L2C_CFG_ICU | L2C_CFG_DCU | L2C_CFG_SS_MASK);
+ r |= L2C_CFG_L2M | L2C_CFG_SS_256;
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CFG, r);
+
+ mtdcr(dcrbase_l2c + DCRN_L2C0_ADDR, 0);
+
+ /* Hardware Clear Command */
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CMD, L2C_CMD_HCC);
+ while (!(mfdcr(dcrbase_l2c + DCRN_L2C0_SR) & L2C_SR_CC))
+ ;
+
+ /* Clear Cache Parity and Tag Errors */
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CMD, L2C_CMD_CCP | L2C_CMD_CTE);
+
+ /* Enable 64G snoop region starting at 0 */
+ r = mfdcr(dcrbase_l2c + DCRN_L2C0_SNP0) &
+ ~(L2C_SNP_BA_MASK | L2C_SNP_SSR_MASK);
+ r |= L2C_SNP_SSR_32G | L2C_SNP_ESR;
+ mtdcr(dcrbase_l2c + DCRN_L2C0_SNP0, r);
+
+ r = mfdcr(dcrbase_l2c + DCRN_L2C0_SNP1) &
+ ~(L2C_SNP_BA_MASK | L2C_SNP_SSR_MASK);
+ r |= 0x80000000 | L2C_SNP_SSR_32G | L2C_SNP_ESR;
+ mtdcr(dcrbase_l2c + DCRN_L2C0_SNP1, r);
+
+ asm volatile ("sync" ::: "memory");
+
+ /* Enable ICU/DCU ports */
+ r = mfdcr(dcrbase_l2c + DCRN_L2C0_CFG);
+ r &= ~(L2C_CFG_DCW_MASK | L2C_CFG_PMUX_MASK | L2C_CFG_PMIM
+ | L2C_CFG_TPEI | L2C_CFG_CPEI | L2C_CFG_NAM | L2C_CFG_NBRM);
+ r |= L2C_CFG_ICU | L2C_CFG_DCU | L2C_CFG_TPC | L2C_CFG_CPC | L2C_CFG_FRAN
+ | L2C_CFG_CPIM | L2C_CFG_TPIM | L2C_CFG_LIM | L2C_CFG_SMCM;
+
+ /* Check for 460EX/GT special handling */
+ if (of_device_is_compatible(np, "ibm,l2-cache-460ex"))
+ r |= L2C_CFG_RDBW;
+
+ mtdcr(dcrbase_l2c + DCRN_L2C0_CFG, r);
+
+ asm volatile ("sync; isync" ::: "memory");
+ local_irq_restore(flags);
+
+ printk(KERN_INFO "%dk L2-cache enabled\n", l2_size >> 10);
+
+ of_node_put(np);
+ return 0;
+}
+arch_initcall(ppc4xx_l2c_probe);
diff --git a/drivers/char/xilinx_hwicap/buffer_icap.c b/drivers/char/xilinx_hwicap/buffer_icap.c
index f577dae..aa7f796 100644
--- a/drivers/char/xilinx_hwicap/buffer_icap.c
+++ b/drivers/char/xilinx_hwicap/buffer_icap.c
@@ -74,7 +74,7 @@
/**
* buffer_icap_get_status - Get the contents of the status register.
- * @base_address: is the base address of the device
+ * @drvdata: a pointer to the drvdata.
*
* The status register contains the ICAP status and the done bit.
*
@@ -88,9 +88,9 @@
* D1 - Always 1
* D0 - Done bit
**/
-static inline u32 buffer_icap_get_status(void __iomem *base_address)
+u32 buffer_icap_get_status(struct hwicap_drvdata *drvdata)
{
- return in_be32(base_address + XHI_STATUS_REG_OFFSET);
+ return in_be32(drvdata->base_address + XHI_STATUS_REG_OFFSET);
}
/**
@@ -117,20 +117,8 @@
**/
static inline bool buffer_icap_busy(void __iomem *base_address)
{
- return (buffer_icap_get_status(base_address) & 1) == XHI_NOT_FINISHED;
-}
-
-/**
- * buffer_icap_busy - Return true if the icap device is not busy
- * @base_address: is the base address of the device
- *
- * The queries the low order bit of the status register, which
- * indicates whether the current configuration or readback operation
- * has completed.
- **/
-static inline bool buffer_icap_done(void __iomem *base_address)
-{
- return (buffer_icap_get_status(base_address) & 1) == XHI_FINISHED;
+ u32 status = in_be32(base_address + XHI_STATUS_REG_OFFSET);
+ return (status & 1) == XHI_NOT_FINISHED;
}
/**
diff --git a/drivers/char/xilinx_hwicap/buffer_icap.h b/drivers/char/xilinx_hwicap/buffer_icap.h
index 0318495..c5b1840 100644
--- a/drivers/char/xilinx_hwicap/buffer_icap.h
+++ b/drivers/char/xilinx_hwicap/buffer_icap.h
@@ -44,8 +44,6 @@
#include <asm/io.h>
#include "xilinx_hwicap.h"
-void buffer_icap_reset(struct hwicap_drvdata *drvdata);
-
/* Loads a partial bitstream from system memory. */
int buffer_icap_set_configuration(struct hwicap_drvdata *drvdata, u32 *data,
u32 Size);
@@ -54,4 +52,7 @@
int buffer_icap_get_configuration(struct hwicap_drvdata *drvdata, u32 *data,
u32 Size);
+u32 buffer_icap_get_status(struct hwicap_drvdata *drvdata);
+void buffer_icap_reset(struct hwicap_drvdata *drvdata);
+
#endif
diff --git a/drivers/char/xilinx_hwicap/fifo_icap.c b/drivers/char/xilinx_hwicap/fifo_icap.c
index 6f45dbd..776b505 100644
--- a/drivers/char/xilinx_hwicap/fifo_icap.c
+++ b/drivers/char/xilinx_hwicap/fifo_icap.c
@@ -78,13 +78,6 @@
#define XHI_CR_READ_MASK 0x00000002 /* Read from ICAP to FIFO */
#define XHI_CR_WRITE_MASK 0x00000001 /* Write from FIFO to ICAP */
-/* Status Register (SR) */
-#define XHI_SR_CFGERR_N_MASK 0x00000100 /* Config Error Mask */
-#define XHI_SR_DALIGN_MASK 0x00000080 /* Data Alignment Mask */
-#define XHI_SR_RIP_MASK 0x00000040 /* Read back Mask */
-#define XHI_SR_IN_ABORT_N_MASK 0x00000020 /* Select Map Abort Mask */
-#define XHI_SR_DONE_MASK 0x00000001 /* Done bit Mask */
-
#define XHI_WFO_MAX_VACANCY 1024 /* Max Write FIFO Vacancy, in words */
#define XHI_RFO_MAX_OCCUPANCY 256 /* Max Read FIFO Occupancy, in words */
@@ -152,13 +145,35 @@
}
/**
+ * fifo_icap_get_status - Get the contents of the status register.
+ * @drvdata: a pointer to the drvdata.
+ *
+ * The status register contains the ICAP status and the done bit.
+ *
+ * D8 - cfgerr
+ * D7 - dalign
+ * D6 - rip
+ * D5 - in_abort_l
+ * D4 - Always 1
+ * D3 - Always 1
+ * D2 - Always 1
+ * D1 - Always 1
+ * D0 - Done bit
+ **/
+u32 fifo_icap_get_status(struct hwicap_drvdata *drvdata)
+{
+ u32 status = in_be32(drvdata->base_address + XHI_SR_OFFSET);
+ dev_dbg(drvdata->dev, "Getting status = %x\n", status);
+ return status;
+}
+
+/**
* fifo_icap_busy - Return true if the ICAP is still processing a transaction.
* @drvdata: a pointer to the drvdata.
**/
static inline u32 fifo_icap_busy(struct hwicap_drvdata *drvdata)
{
u32 status = in_be32(drvdata->base_address + XHI_SR_OFFSET);
- dev_dbg(drvdata->dev, "Getting status = %x\n", status);
return (status & XHI_SR_DONE_MASK) ? 0 : 1;
}
diff --git a/drivers/char/xilinx_hwicap/fifo_icap.h b/drivers/char/xilinx_hwicap/fifo_icap.h
index 4d3068d..ffabd3b 100644
--- a/drivers/char/xilinx_hwicap/fifo_icap.h
+++ b/drivers/char/xilinx_hwicap/fifo_icap.h
@@ -56,6 +56,7 @@
u32 *FrameBuffer,
u32 NumWords);
+u32 fifo_icap_get_status(struct hwicap_drvdata *drvdata);
void fifo_icap_reset(struct hwicap_drvdata *drvdata);
void fifo_icap_flush_fifo(struct hwicap_drvdata *drvdata);
diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.c b/drivers/char/xilinx_hwicap/xilinx_hwicap.c
index 2284fa2..016f905 100644
--- a/drivers/char/xilinx_hwicap/xilinx_hwicap.c
+++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.c
@@ -36,7 +36,7 @@
*****************************************************************************/
/*
- * This is the code behind /dev/xilinx_icap -- it allows a user-space
+ * This is the code behind /dev/icap* -- it allows a user-space
* application to use the Xilinx ICAP subsystem.
*
* The following operations are possible:
@@ -67,7 +67,7 @@
* user-space application code that uses this device. The simplest
* way to use this interface is simply:
*
- * cp foo.bit /dev/xilinx_icap
+ * cp foo.bit /dev/icap0
*
* Note that unless foo.bit is an appropriately constructed partial
* bitstream, this has a high likelyhood of overwriting the design
@@ -105,18 +105,14 @@
#include "buffer_icap.h"
#include "fifo_icap.h"
-#define DRIVER_NAME "xilinx_icap"
+#define DRIVER_NAME "icap"
#define HWICAP_REGS (0x10000)
-/* dynamically allocate device number */
-static int xhwicap_major;
-static int xhwicap_minor;
+#define XHWICAP_MAJOR 259
+#define XHWICAP_MINOR 0
#define HWICAP_DEVICES 1
-module_param(xhwicap_major, int, S_IRUGO);
-module_param(xhwicap_minor, int, S_IRUGO);
-
/* An array, which is set to true when the device is registered. */
static bool probed_devices[HWICAP_DEVICES];
static struct mutex icap_sem;
@@ -250,8 +246,26 @@
* Create the data to be written to the ICAP.
*/
buffer[index++] = XHI_DUMMY_PACKET;
+ buffer[index++] = XHI_NOOP_PACKET;
buffer[index++] = XHI_SYNC_PACKET;
buffer[index++] = XHI_NOOP_PACKET;
+ buffer[index++] = XHI_NOOP_PACKET;
+
+ /*
+ * Write the data to the FIFO and initiate the transfer of data present
+ * in the FIFO to the ICAP device.
+ */
+ status = drvdata->config->set_configuration(drvdata,
+ &buffer[0], index);
+ if (status)
+ return status;
+
+ /* If the syncword was not found, then we need to start over. */
+ status = drvdata->config->get_status(drvdata);
+ if ((status & XHI_SR_DALIGN_MASK) != XHI_SR_DALIGN_MASK)
+ return -EIO;
+
+ index = 0;
buffer[index++] = hwicap_type_1_read(reg) | 1;
buffer[index++] = XHI_NOOP_PACKET;
buffer[index++] = XHI_NOOP_PACKET;
@@ -587,7 +601,7 @@
probed_devices[id] = 1;
mutex_unlock(&icap_sem);
- devt = MKDEV(xhwicap_major, xhwicap_minor + id);
+ devt = MKDEV(XHWICAP_MAJOR, XHWICAP_MINOR + id);
drvdata = kzalloc(sizeof(struct hwicap_drvdata), GFP_KERNEL);
if (!drvdata) {
@@ -664,12 +678,14 @@
static struct hwicap_driver_config buffer_icap_config = {
.get_configuration = buffer_icap_get_configuration,
.set_configuration = buffer_icap_set_configuration,
+ .get_status = buffer_icap_get_status,
.reset = buffer_icap_reset,
};
static struct hwicap_driver_config fifo_icap_config = {
.get_configuration = fifo_icap_get_configuration,
.set_configuration = fifo_icap_set_configuration,
+ .get_status = fifo_icap_get_status,
.reset = fifo_icap_reset,
};
@@ -690,7 +706,7 @@
dev_set_drvdata(dev, NULL);
mutex_lock(&icap_sem);
- probed_devices[MINOR(dev->devt)-xhwicap_minor] = 0;
+ probed_devices[MINOR(dev->devt)-XHWICAP_MINOR] = 0;
mutex_unlock(&icap_sem);
return 0; /* success */
}
@@ -830,23 +846,12 @@
icap_class = class_create(THIS_MODULE, "xilinx_config");
mutex_init(&icap_sem);
- if (xhwicap_major) {
- devt = MKDEV(xhwicap_major, xhwicap_minor);
- retval = register_chrdev_region(
- devt,
- HWICAP_DEVICES,
- DRIVER_NAME);
- if (retval < 0)
- return retval;
- } else {
- retval = alloc_chrdev_region(&devt,
- xhwicap_minor,
- HWICAP_DEVICES,
- DRIVER_NAME);
- if (retval < 0)
- return retval;
- xhwicap_major = MAJOR(devt);
- }
+ devt = MKDEV(XHWICAP_MAJOR, XHWICAP_MINOR);
+ retval = register_chrdev_region(devt,
+ HWICAP_DEVICES,
+ DRIVER_NAME);
+ if (retval < 0)
+ return retval;
retval = platform_driver_register(&hwicap_platform_driver);
@@ -871,7 +876,7 @@
static void __exit hwicap_module_cleanup(void)
{
- dev_t devt = MKDEV(xhwicap_major, xhwicap_minor);
+ dev_t devt = MKDEV(XHWICAP_MAJOR, XHWICAP_MINOR);
class_destroy(icap_class);
diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.h b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
index 405fee7..1f9c8b0 100644
--- a/drivers/char/xilinx_hwicap/xilinx_hwicap.h
+++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
@@ -65,10 +65,27 @@
};
struct hwicap_driver_config {
+ /* Read configuration data given by size into the data buffer.
+ Return 0 if successful. */
int (*get_configuration)(struct hwicap_drvdata *drvdata, u32 *data,
u32 size);
+ /* Write configuration data given by size from the data buffer.
+ Return 0 if successful. */
int (*set_configuration)(struct hwicap_drvdata *drvdata, u32 *data,
u32 size);
+ /* Get the status register, bit pattern given by:
+ * D8 - 0 = configuration error
+ * D7 - 1 = alignment found
+ * D6 - 1 = readback in progress
+ * D5 - 0 = abort in progress
+ * D4 - Always 1
+ * D3 - Always 1
+ * D2 - Always 1
+ * D1 - Always 1
+ * D0 - 1 = operation completed
+ */
+ u32 (*get_status)(struct hwicap_drvdata *drvdata);
+ /* Reset the hw */
void (*reset)(struct hwicap_drvdata *drvdata);
};
@@ -163,6 +180,13 @@
/* Constant to use for CRC check when CRC has been disabled */
#define XHI_DISABLED_AUTO_CRC 0x0000DEFCUL
+/* Meanings of the bits returned by get_status */
+#define XHI_SR_CFGERR_N_MASK 0x00000100 /* Config Error Mask */
+#define XHI_SR_DALIGN_MASK 0x00000080 /* Data Alignment Mask */
+#define XHI_SR_RIP_MASK 0x00000040 /* Read back Mask */
+#define XHI_SR_IN_ABORT_N_MASK 0x00000020 /* Select Map Abort Mask */
+#define XHI_SR_DONE_MASK 0x00000001 /* Done bit Mask */
+
/**
* hwicap_type_1_read - Generates a Type 1 read packet header.
* @reg: is the address of the register to be read back.
diff --git a/include/asm-powerpc/dcr-native.h b/include/asm-powerpc/dcr-native.h
index be6c879..f8398ce 100644
--- a/include/asm-powerpc/dcr-native.h
+++ b/include/asm-powerpc/dcr-native.h
@@ -82,6 +82,19 @@
spin_unlock_irqrestore(&dcr_ind_lock, flags);
}
+static inline void __dcri_clrset(int base_addr, int base_data, int reg,
+ unsigned clr, unsigned set)
+{
+ unsigned long flags;
+ unsigned int val;
+
+ spin_lock_irqsave(&dcr_ind_lock, flags);
+ __mtdcr(base_addr, reg);
+ val = (__mfdcr(base_data) & ~clr) | set;
+ __mtdcr(base_data, val);
+ spin_unlock_irqrestore(&dcr_ind_lock, flags);
+}
+
#define mfdcri(base, reg) __mfdcri(DCRN_ ## base ## _CONFIG_ADDR, \
DCRN_ ## base ## _CONFIG_DATA, \
reg)
@@ -90,6 +103,10 @@
DCRN_ ## base ## _CONFIG_DATA, \
reg, data)
+#define dcri_clrset(base, reg, clr, set) __dcri_clrset(DCRN_ ## base ## _CONFIG_ADDR, \
+ DCRN_ ## base ## _CONFIG_DATA, \
+ reg, clr, set)
+
#endif /* __ASSEMBLY__ */
#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_DCR_NATIVE_H */
diff --git a/include/asm-powerpc/dcr-regs.h b/include/asm-powerpc/dcr-regs.h
index 9f1fb98..29b0ece 100644
--- a/include/asm-powerpc/dcr-regs.h
+++ b/include/asm-powerpc/dcr-regs.h
@@ -68,4 +68,82 @@
#define SDR0_UART3 0x0123
#define SDR0_CUST0 0x4000
+/*
+ * All those DCR register addresses are offsets from the base address
+ * for the SRAM0 controller (e.g. 0x20 on 440GX). The base address is
+ * excluded here and configured in the device tree.
+ */
+#define DCRN_SRAM0_SB0CR 0x00
+#define DCRN_SRAM0_SB1CR 0x01
+#define DCRN_SRAM0_SB2CR 0x02
+#define DCRN_SRAM0_SB3CR 0x03
+#define SRAM_SBCR_BU_MASK 0x00000180
+#define SRAM_SBCR_BS_64KB 0x00000800
+#define SRAM_SBCR_BU_RO 0x00000080
+#define SRAM_SBCR_BU_RW 0x00000180
+#define DCRN_SRAM0_BEAR 0x04
+#define DCRN_SRAM0_BESR0 0x05
+#define DCRN_SRAM0_BESR1 0x06
+#define DCRN_SRAM0_PMEG 0x07
+#define DCRN_SRAM0_CID 0x08
+#define DCRN_SRAM0_REVID 0x09
+#define DCRN_SRAM0_DPC 0x0a
+#define SRAM_DPC_ENABLE 0x80000000
+
+/*
+ * All those DCR register addresses are offsets from the base address
+ * for the SRAM0 controller (e.g. 0x30 on 440GX). The base address is
+ * excluded here and configured in the device tree.
+ */
+#define DCRN_L2C0_CFG 0x00
+#define L2C_CFG_L2M 0x80000000
+#define L2C_CFG_ICU 0x40000000
+#define L2C_CFG_DCU 0x20000000
+#define L2C_CFG_DCW_MASK 0x1e000000
+#define L2C_CFG_TPC 0x01000000
+#define L2C_CFG_CPC 0x00800000
+#define L2C_CFG_FRAN 0x00200000
+#define L2C_CFG_SS_MASK 0x00180000
+#define L2C_CFG_SS_256 0x00000000
+#define L2C_CFG_CPIM 0x00040000
+#define L2C_CFG_TPIM 0x00020000
+#define L2C_CFG_LIM 0x00010000
+#define L2C_CFG_PMUX_MASK 0x00007000
+#define L2C_CFG_PMUX_SNP 0x00000000
+#define L2C_CFG_PMUX_IF 0x00001000
+#define L2C_CFG_PMUX_DF 0x00002000
+#define L2C_CFG_PMUX_DS 0x00003000
+#define L2C_CFG_PMIM 0x00000800
+#define L2C_CFG_TPEI 0x00000400
+#define L2C_CFG_CPEI 0x00000200
+#define L2C_CFG_NAM 0x00000100
+#define L2C_CFG_SMCM 0x00000080
+#define L2C_CFG_NBRM 0x00000040
+#define L2C_CFG_RDBW 0x00000008 /* only 460EX/GT */
+#define DCRN_L2C0_CMD 0x01
+#define L2C_CMD_CLR 0x80000000
+#define L2C_CMD_DIAG 0x40000000
+#define L2C_CMD_INV 0x20000000
+#define L2C_CMD_CCP 0x10000000
+#define L2C_CMD_CTE 0x08000000
+#define L2C_CMD_STRC 0x04000000
+#define L2C_CMD_STPC 0x02000000
+#define L2C_CMD_RPMC 0x01000000
+#define L2C_CMD_HCC 0x00800000
+#define DCRN_L2C0_ADDR 0x02
+#define DCRN_L2C0_DATA 0x03
+#define DCRN_L2C0_SR 0x04
+#define L2C_SR_CC 0x80000000
+#define L2C_SR_CPE 0x40000000
+#define L2C_SR_TPE 0x20000000
+#define L2C_SR_LRU 0x10000000
+#define L2C_SR_PCS 0x08000000
+#define DCRN_L2C0_REVID 0x05
+#define DCRN_L2C0_SNP0 0x06
+#define DCRN_L2C0_SNP1 0x07
+#define L2C_SNP_BA_MASK 0xffff0000
+#define L2C_SNP_SSR_MASK 0x0000f000
+#define L2C_SNP_SSR_32G 0x0000f000
+#define L2C_SNP_ESR 0x00000800
+
#endif /* __DCR_REGS_H__ */