[ARM] 4146/1: AT91: Support for AT91SAM9263-EK board.
Add support for the Atmel AT91SAM9263-EK board.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 2499385..9313888 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -121,17 +121,32 @@
# ----------------------------------------------------------
+if ARCH_AT91SAM9263
+
+comment "AT91SAM9263 Board Type"
+
+config MACH_AT91SAM9263EK
+ bool "Atmel AT91SAM9263-EK Evaluation Kit"
+ depends on ARCH_AT91SAM9263
+ help
+ Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
+ <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
+
+endif
+
+# ----------------------------------------------------------
+
comment "AT91 Board Options"
config MTD_AT91_DATAFLASH_CARD
bool "Enable DataFlash Card support"
- depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK)
+ depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
help
Enable support for the DataFlash card.
config MTD_NAND_AT91_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
- depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK)
+ depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 2fd4cd4..05de6cd 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -32,6 +32,9 @@
# AT91SAM9261 board-specific support
obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
+# AT91SAM9263 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
+
# LEDs support
led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o
led-$(CONFIG_MACH_AT91RM9200EK) += leds.o
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
new file mode 100644
index 0000000..8fdce11
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -0,0 +1,176 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9263ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ * 0 .. 2 = USART0 .. USART2
+ * 3 = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+ .console_tty = 0, /* ttyS0 */
+ .nr_tty = 2,
+ .tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */
+};
+
+static void __init ek_map_io(void)
+{
+ /* Initialize processor: 16.367 MHz crystal */
+ at91sam9263_initialize(16367660);
+
+ /* Setup the serial ports and console */
+ at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+ at91sam9263_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+ .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PA25,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .wire4 = 1,
+ .det_pin = AT91_PIN_PE18,
+ .wp_pin = AT91_PIN_PE19,
+// .vcc_pin = ... not connected
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Partition 1",
+ .offset = 0,
+ .size = 64 * 1024 * 1024,
+ },
+ {
+ .name = "Partition 2",
+ .offset = 64 * 1024 * 1024,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(ek_nand_partition);
+ return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+ .ale = 21,
+ .cle = 22,
+// .det_pin = ... not connected
+ .rdy_pin = AT91_PIN_PA22,
+ .enable_pin = AT91_PIN_PD15,
+ .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+ .bus_width_16 = 1,
+#else
+ .bus_width_16 = 0,
+#endif
+};
+
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* MMC */
+ at91_add_device_mmc(1, &ek_mmc_data);
+ /* NAND */
+ at91_add_device_nand(&ek_nand_data);
+}
+
+MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
+ /* Maintainer: Atmel */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = ek_map_io,
+ .init_irq = ek_init_irq,
+ .init_machine = ek_board_init,
+MACHINE_END