diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 1d35459..83fc636 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -534,6 +534,118 @@
 	}
 }
 
+/*
+ * Converts a raw xHCI port status into the format that external USB 2.0 or USB
+ * 3.0 hubs use.
+ *
+ * Possible side effects:
+ *  - Mark a port as being done with device resume,
+ *    and ring the endpoint doorbells.
+ *  - Stop the Synopsys redriver Compliance Mode polling.
+ */
+static u32 xhci_get_port_status(struct usb_hcd *hcd,
+		struct xhci_bus_state *bus_state,
+		__le32 __iomem **port_array,
+		u16 wIndex, u32 raw_port_status)
+{
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+	u32 status = 0;
+	int slot_id;
+
+	/* wPortChange bits */
+	if (raw_port_status & PORT_CSC)
+		status |= USB_PORT_STAT_C_CONNECTION << 16;
+	if (raw_port_status & PORT_PEC)
+		status |= USB_PORT_STAT_C_ENABLE << 16;
+	if ((raw_port_status & PORT_OCC))
+		status |= USB_PORT_STAT_C_OVERCURRENT << 16;
+	if ((raw_port_status & PORT_RC))
+		status |= USB_PORT_STAT_C_RESET << 16;
+	/* USB3.0 only */
+	if (hcd->speed == HCD_USB3) {
+		if ((raw_port_status & PORT_PLC))
+			status |= USB_PORT_STAT_C_LINK_STATE << 16;
+		if ((raw_port_status & PORT_WRC))
+			status |= USB_PORT_STAT_C_BH_RESET << 16;
+	}
+
+	if (hcd->speed != HCD_USB3) {
+		if ((raw_port_status & PORT_PLS_MASK) == XDEV_U3
+				&& (raw_port_status & PORT_POWER))
+			status |= USB_PORT_STAT_SUSPEND;
+	}
+	if ((raw_port_status & PORT_PLS_MASK) == XDEV_RESUME &&
+			!DEV_SUPERSPEED(raw_port_status)) {
+		if ((raw_port_status & PORT_RESET) ||
+				!(raw_port_status & PORT_PE))
+			return 0xffffffff;
+		if (time_after_eq(jiffies,
+					bus_state->resume_done[wIndex])) {
+			xhci_dbg(xhci, "Resume USB2 port %d\n",
+					wIndex + 1);
+			bus_state->resume_done[wIndex] = 0;
+			clear_bit(wIndex, &bus_state->resuming_ports);
+			xhci_set_link_state(xhci, port_array, wIndex,
+					XDEV_U0);
+			xhci_dbg(xhci, "set port %d resume\n",
+					wIndex + 1);
+			slot_id = xhci_find_slot_id_by_port(hcd, xhci,
+					wIndex + 1);
+			if (!slot_id) {
+				xhci_dbg(xhci, "slot_id is zero\n");
+				return 0xffffffff;
+			}
+			xhci_ring_device(xhci, slot_id);
+			bus_state->port_c_suspend |= 1 << wIndex;
+			bus_state->suspended_ports &= ~(1 << wIndex);
+		} else {
+			/*
+			 * The resume has been signaling for less than
+			 * 20ms. Report the port status as SUSPEND,
+			 * let the usbcore check port status again
+			 * and clear resume signaling later.
+			 */
+			status |= USB_PORT_STAT_SUSPEND;
+		}
+	}
+	if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0
+			&& (raw_port_status & PORT_POWER)
+			&& (bus_state->suspended_ports & (1 << wIndex))) {
+		bus_state->suspended_ports &= ~(1 << wIndex);
+		if (hcd->speed != HCD_USB3)
+			bus_state->port_c_suspend |= 1 << wIndex;
+	}
+	if (raw_port_status & PORT_CONNECT) {
+		status |= USB_PORT_STAT_CONNECTION;
+		status |= xhci_port_speed(raw_port_status);
+	}
+	if (raw_port_status & PORT_PE)
+		status |= USB_PORT_STAT_ENABLE;
+	if (raw_port_status & PORT_OC)
+		status |= USB_PORT_STAT_OVERCURRENT;
+	if (raw_port_status & PORT_RESET)
+		status |= USB_PORT_STAT_RESET;
+	if (raw_port_status & PORT_POWER) {
+		if (hcd->speed == HCD_USB3)
+			status |= USB_SS_PORT_STAT_POWER;
+		else
+			status |= USB_PORT_STAT_POWER;
+	}
+	/* Update Port Link State for super speed ports*/
+	if (hcd->speed == HCD_USB3) {
+		xhci_hub_report_link_state(&status, raw_port_status);
+		/*
+		 * Verify if all USB3 Ports Have entered U0 already.
+		 * Delete Compliance Mode Timer if so.
+		 */
+		xhci_del_comp_mod_timer(xhci, raw_port_status, wIndex);
+	}
+	if (bus_state->port_c_suspend & (1 << wIndex))
+		status |= 1 << USB_PORT_FEAT_C_SUSPEND;
+
+	return status;
+}
+
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 		u16 wIndex, char *buf, u16 wLength)
 {
@@ -598,104 +710,20 @@
 		if (!wIndex || wIndex > max_ports)
 			goto error;
 		wIndex--;
-		status = 0;
 		temp = xhci_readl(xhci, port_array[wIndex]);
 		if (temp == 0xffffffff) {
 			retval = -ENODEV;
 			break;
 		}
-		xhci_dbg(xhci, "get port status, actual port %d status  = 0x%x\n", wIndex, temp);
+		status = xhci_get_port_status(hcd, bus_state, port_array,
+				wIndex, temp);
+		if (status == 0xffffffff)
+			goto error;
 
-		/* wPortChange bits */
-		if (temp & PORT_CSC)
-			status |= USB_PORT_STAT_C_CONNECTION << 16;
-		if (temp & PORT_PEC)
-			status |= USB_PORT_STAT_C_ENABLE << 16;
-		if ((temp & PORT_OCC))
-			status |= USB_PORT_STAT_C_OVERCURRENT << 16;
-		if ((temp & PORT_RC))
-			status |= USB_PORT_STAT_C_RESET << 16;
-		/* USB3.0 only */
-		if (hcd->speed == HCD_USB3) {
-			if ((temp & PORT_PLC))
-				status |= USB_PORT_STAT_C_LINK_STATE << 16;
-			if ((temp & PORT_WRC))
-				status |= USB_PORT_STAT_C_BH_RESET << 16;
-		}
-
-		if (hcd->speed != HCD_USB3) {
-			if ((temp & PORT_PLS_MASK) == XDEV_U3
-					&& (temp & PORT_POWER))
-				status |= USB_PORT_STAT_SUSPEND;
-		}
-		if ((temp & PORT_PLS_MASK) == XDEV_RESUME &&
-				!DEV_SUPERSPEED(temp)) {
-			if ((temp & PORT_RESET) || !(temp & PORT_PE))
-				goto error;
-			if (time_after_eq(jiffies,
-					bus_state->resume_done[wIndex])) {
-				xhci_dbg(xhci, "Resume USB2 port %d\n",
-					wIndex + 1);
-				bus_state->resume_done[wIndex] = 0;
-				clear_bit(wIndex, &bus_state->resuming_ports);
-				xhci_set_link_state(xhci, port_array, wIndex,
-							XDEV_U0);
-				xhci_dbg(xhci, "set port %d resume\n",
-					wIndex + 1);
-				slot_id = xhci_find_slot_id_by_port(hcd, xhci,
-								 wIndex + 1);
-				if (!slot_id) {
-					xhci_dbg(xhci, "slot_id is zero\n");
-					goto error;
-				}
-				xhci_ring_device(xhci, slot_id);
-				bus_state->port_c_suspend |= 1 << wIndex;
-				bus_state->suspended_ports &= ~(1 << wIndex);
-			} else {
-				/*
-				 * The resume has been signaling for less than
-				 * 20ms. Report the port status as SUSPEND,
-				 * let the usbcore check port status again
-				 * and clear resume signaling later.
-				 */
-				status |= USB_PORT_STAT_SUSPEND;
-			}
-		}
-		if ((temp & PORT_PLS_MASK) == XDEV_U0
-			&& (temp & PORT_POWER)
-			&& (bus_state->suspended_ports & (1 << wIndex))) {
-			bus_state->suspended_ports &= ~(1 << wIndex);
-			if (hcd->speed != HCD_USB3)
-				bus_state->port_c_suspend |= 1 << wIndex;
-		}
-		if (temp & PORT_CONNECT) {
-			status |= USB_PORT_STAT_CONNECTION;
-			status |= xhci_port_speed(temp);
-		}
-		if (temp & PORT_PE)
-			status |= USB_PORT_STAT_ENABLE;
-		if (temp & PORT_OC)
-			status |= USB_PORT_STAT_OVERCURRENT;
-		if (temp & PORT_RESET)
-			status |= USB_PORT_STAT_RESET;
-		if (temp & PORT_POWER) {
-			if (hcd->speed == HCD_USB3)
-				status |= USB_SS_PORT_STAT_POWER;
-			else
-				status |= USB_PORT_STAT_POWER;
-		}
-		/* Update Port Link State for super speed ports*/
-		if (hcd->speed == HCD_USB3) {
-			xhci_hub_report_link_state(&status, temp);
-			/*
-			 * Verify if all USB3 Ports Have entered U0 already.
-			 * Delete Compliance Mode Timer if so.
-			 */
-			xhci_del_comp_mod_timer(xhci, temp, wIndex);
-		}
-		if (bus_state->port_c_suspend & (1 << wIndex))
-			status |= 1 << USB_PORT_FEAT_C_SUSPEND;
+		xhci_dbg(xhci, "get port status, actual port %d status  = 0x%x\n",
+				wIndex, temp);
 		xhci_dbg(xhci, "Get port status returned 0x%x\n", status);
+
 		put_unaligned(cpu_to_le32(status), (__le32 *) buf);
 		break;
 	case SetPortFeature: