MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel
The following patch add support for the NXP PNX833x SOC. More
specifically it adds support for the STB222/5 variant. It fixes
the vectored interrupt issue.
Signed-off-by: daniel.j.laird <daniel.j.laird@nxp.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/arch/mips/nxp/pnx833x/common/setup.c b/arch/mips/nxp/pnx833x/common/setup.c
new file mode 100644
index 0000000..e51fbc4
--- /dev/null
+++ b/arch/mips/nxp/pnx833x/common/setup.c
@@ -0,0 +1,64 @@
+/*
+ * setup.c: Setup PNX833X Soc.
+ *
+ * Copyright 2008 NXP Semiconductors
+ * Chris Steel <chris.steel@nxp.com>
+ * Daniel Laird <daniel.j.laird@nxp.com>
+ *
+ * Based on software written by:
+ * Nikita Youshchenko <yoush@debian.org>, based on PNX8550 code.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/pci.h>
+#include <asm/reboot.h>
+#include <pnx833x.h>
+#include <gpio.h>
+
+extern void pnx833x_board_setup(void);
+extern void pnx833x_machine_restart(char *);
+extern void pnx833x_machine_halt(void);
+extern void pnx833x_machine_power_off(void);
+
+int __init plat_mem_setup(void)
+{
+ /* fake pci bus to avoid bounce buffers */
+ PCI_DMA_BUS_IS_PHYS = 1;
+
+ /* set mips clock to 320MHz */
+#if defined(CONFIG_SOC_PNX8335)
+ PNX8335_WRITEFIELD(0x17, CLOCK_PLL_CPU_CTL, FREQ);
+#endif
+ pnx833x_gpio_init(); /* so it will be ready in board_setup() */
+
+ pnx833x_board_setup();
+
+ _machine_restart = pnx833x_machine_restart;
+ _machine_halt = pnx833x_machine_halt;
+ pm_power_off = pnx833x_machine_power_off;
+
+ /* IO/MEM resources. */
+ set_io_port_base(KSEG1);
+ ioport_resource.start = 0;
+ ioport_resource.end = ~0;
+ iomem_resource.start = 0;
+ iomem_resource.end = ~0;
+
+ return 0;
+}