Merge tag 'arc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Support for HSDK board hosting a Quad core HS38x4 based SoC running
@1GHz (and some prerrquisite changes such as ability to scoot the
kernel code/data from start of memory map etc)
- Quite a few updates for EZChip (Mellanox) platform
- Fixes to fault/exception printing
* tag 'arc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (26 commits)
ARC: Re-enable MMU upon Machine Check exception
ARC: Show fault information passed to show_kernel_fault_diag()
ARC: [plat-hsdk] initial port for HSDK board
ARC: mm: Decouple RAM base address from kernel link address
ARCv2: IOC: Tighten up the contraints (specifically base / size alignment)
ARC: [plat-axs103] refactor the DT fudging code
ARC: [plat-axs103] use clk driver #2: Add core pll node to DT to manage cpu clk
ARC: [plat-axs103] use clk driver #1: Get rid of platform specific cpu clk setting
ARCv2: SLC: provide a line based flush routine for debugging
ARC: Hardcode ARCH_DMA_MINALIGN to max line length we may have
ARC: [plat-eznps] handle extra aux regs #2: kernel/entry exit
ARC: [plat-eznps] handle extra aux regs #1: save/restore on context switch
ARC: [plat-eznps] avoid toggling of DPC register
ARC: [plat-eznps] Update the init sequence of aux regs per cpu.
ARC: [plat-eznps] new command line argument for HW scheduler at MTM
ARC: set boot print log level to PR_INFO
ARC: [plat-eznps] Handle user memory error same in simulation and silicon
ARC: [plat-eznps] use schd.wft instruction instead of sleep at idle task
ARC: create cpu specific version of arch_cpu_idle()
ARC: [plat-eznps] spinlock aware for MTM
...
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 86b0e8e..0549662 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -2764,6 +2764,15 @@
If the dependencies are under your control, you can
turn on cpu0_hotplug.
+ nps_mtm_hs_ctr= [KNL,ARC]
+ This parameter sets the maximum duration, in
+ cycles, each HW thread of the CTOP can run
+ without interruptions, before HW switches it.
+ The actual maximum duration is 16 times this
+ parameter's value.
+ Format: integer between 1 and 255
+ Default: 255
+
nptcg= [IA-64] Override max number of concurrent global TLB
purges which is reported from either PAL_VM_SUMMARY or
SAL PALO.
diff --git a/Documentation/devicetree/bindings/arc/hsdk.txt b/Documentation/devicetree/bindings/arc/hsdk.txt
new file mode 100644
index 0000000..be50654
--- /dev/null
+++ b/Documentation/devicetree/bindings/arc/hsdk.txt
@@ -0,0 +1,7 @@
+Synopsys DesignWare ARC HS Development Kit Device Tree Bindings
+---------------------------------------------------------------------------
+
+ARC HSDK Board with quad-core ARC HS38x4 in silicon.
+
+Required root node properties:
+ - compatible = "snps,hsdk";
diff --git a/arch/arc/Kconfig b/arch/arc/Kconfig
index 7db85ab..a598641 100644
--- a/arch/arc/Kconfig
+++ b/arch/arc/Kconfig
@@ -100,6 +100,7 @@
source "arch/arc/plat-axs10x/Kconfig"
#New platform adds here
source "arch/arc/plat-eznps/Kconfig"
+source "arch/arc/plat-hsdk/Kconfig"
endmenu
@@ -418,7 +419,7 @@
endmenu # "ARC CPU Configuration"
config LINUX_LINK_BASE
- hex "Linux Link Address"
+ hex "Kernel link address"
default "0x80000000"
help
ARC700 divides the 32 bit phy address space into two equal halves
@@ -431,6 +432,14 @@
If you don't know what the above means, leave this setting alone.
This needs to match memory start address specified in Device Tree
+config LINUX_RAM_BASE
+ hex "RAM base address"
+ default LINUX_LINK_BASE
+ help
+ By default Linux is linked at base of RAM. However in some special
+ cases (such as HSDK), Linux can't be linked at start of DDR, hence
+ this option.
+
config HIGHMEM
bool "High Memory Support"
select ARCH_DISCONTIGMEM_ENABLE
diff --git a/arch/arc/Makefile b/arch/arc/Makefile
index 3a61cfc..3a4b52b 100644
--- a/arch/arc/Makefile
+++ b/arch/arc/Makefile
@@ -111,6 +111,7 @@
core-$(CONFIG_ARC_PLAT_TB10X) += arch/arc/plat-tb10x/
core-$(CONFIG_ARC_PLAT_AXS10X) += arch/arc/plat-axs10x/
core-$(CONFIG_ARC_PLAT_EZNPS) += arch/arc/plat-eznps/
+core-$(CONFIG_ARC_SOC_HSDK) += arch/arc/plat-hsdk/
ifdef CONFIG_ARC_PLAT_EZNPS
KBUILD_CPPFLAGS += -I$(srctree)/arch/arc/plat-eznps/include
diff --git a/arch/arc/boot/dts/axc001.dtsi b/arch/arc/boot/dts/axc001.dtsi
index a380ffa..fdc2665 100644
--- a/arch/arc/boot/dts/axc001.dtsi
+++ b/arch/arc/boot/dts/axc001.dtsi
@@ -99,7 +99,7 @@
memory {
device_type = "memory";
- /* CONFIG_KERNEL_RAM_BASE_ADDRESS needs to match low mem start */
+ /* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x1b000000>; /* (512 - 32) MiB */
};
diff --git a/arch/arc/boot/dts/axc003.dtsi b/arch/arc/boot/dts/axc003.dtsi
index cc9239e..4e6e9f5 100644
--- a/arch/arc/boot/dts/axc003.dtsi
+++ b/arch/arc/boot/dts/axc003.dtsi
@@ -24,10 +24,17 @@
ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
- core_clk: core_clk {
+ input_clk: input-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
- clock-frequency = <90000000>;
+ clock-frequency = <33333333>;
+ };
+
+ core_clk: core-clk@80 {
+ compatible = "snps,axs10x-arc-pll-clock";
+ reg = <0x80 0x10>, <0x100 0x10>;
+ #clock-cells = <0>;
+ clocks = <&input_clk>;
};
core_intc: archs-intc@cpu {
@@ -102,7 +109,7 @@
memory {
device_type = "memory";
- /* CONFIG_KERNEL_RAM_BASE_ADDRESS needs to match low mem start */
+ /* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */
0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */
};
diff --git a/arch/arc/boot/dts/axc003_idu.dtsi b/arch/arc/boot/dts/axc003_idu.dtsi
index 4ebb2170..63954a8 100644
--- a/arch/arc/boot/dts/axc003_idu.dtsi
+++ b/arch/arc/boot/dts/axc003_idu.dtsi
@@ -24,10 +24,17 @@
ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
- core_clk: core_clk {
+ input_clk: input-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
- clock-frequency = <100000000>;
+ clock-frequency = <33333333>;
+ };
+
+ core_clk: core-clk@80 {
+ compatible = "snps,axs10x-arc-pll-clock";
+ reg = <0x80 0x10>, <0x100 0x10>;
+ #clock-cells = <0>;
+ clocks = <&input_clk>;
};
core_intc: archs-intc@cpu {
@@ -108,7 +115,7 @@
memory {
device_type = "memory";
- /* CONFIG_KERNEL_RAM_BASE_ADDRESS needs to match low mem start */
+ /* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */
0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */
};
diff --git a/arch/arc/boot/dts/hsdk.dts b/arch/arc/boot/dts/hsdk.dts
new file mode 100644
index 0000000..229d13a
--- /dev/null
+++ b/arch/arc/boot/dts/hsdk.dts
@@ -0,0 +1,189 @@
+/*
+ * Copyright (C) 2017 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Device Tree for ARC HS Development Kit
+ */
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ model = "snps,hsdk";
+ compatible = "snps,hsdk";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0xf0005000,115200n8 console=ttyS0,115200n8 debug print-fatal-signals=1";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "snps,archs38";
+ reg = <0>;
+ clocks = <&core_clk>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "snps,archs38";
+ reg = <1>;
+ clocks = <&core_clk>;
+ };
+
+ cpu@2 {
+ device_type = "cpu";
+ compatible = "snps,archs38";
+ reg = <2>;
+ clocks = <&core_clk>;
+ };
+
+ cpu@3 {
+ device_type = "cpu";
+ compatible = "snps,archs38";
+ reg = <3>;
+ clocks = <&core_clk>;
+ };
+ };
+
+ core_clk: core-clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <500000000>;
+ };
+
+ cpu_intc: cpu-interrupt-controller {
+ compatible = "snps,archs-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ idu_intc: idu-interrupt-controller {
+ compatible = "snps,archs-idu-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&cpu_intc>;
+ };
+
+ arcpct: pct {
+ compatible = "snps,archs-pct";
+ };
+
+ /* TIMER0 with interrupt for clockevent */
+ timer {
+ compatible = "snps,arc-timer";
+ interrupts = <16>;
+ interrupt-parent = <&cpu_intc>;
+ clocks = <&core_clk>;
+ };
+
+ /* 64-bit Global Free Running Counter */
+ gfrc {
+ compatible = "snps,archs-timer-gfrc";
+ clocks = <&core_clk>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&idu_intc>;
+
+ ranges = <0x00000000 0xf0000000 0x10000000>;
+
+ serial: serial@5000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x5000 0x100>;
+ clock-frequency = <33330000>;
+ interrupts = <6>;
+ baud = <115200>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ gmacclk: gmacclk {
+ compatible = "fixed-clock";
+ clock-frequency = <400000000>;
+ #clock-cells = <0>;
+ };
+
+ mmcclk_ciu: mmcclk-ciu {
+ compatible = "fixed-clock";
+ clock-frequency = <100000000>;
+ #clock-cells = <0>;
+ };
+
+ mmcclk_biu: mmcclk-biu {
+ compatible = "fixed-clock";
+ clock-frequency = <400000000>;
+ #clock-cells = <0>;
+ };
+
+ ethernet@8000 {
+ #interrupt-cells = <1>;
+ compatible = "snps,dwmac";
+ reg = <0x8000 0x2000>;
+ interrupts = <10>;
+ interrupt-names = "macirq";
+ phy-mode = "rgmii";
+ snps,pbl = <32>;
+ clocks = <&gmacclk>;
+ clock-names = "stmmaceth";
+ phy-handle = <&phy0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+ };
+ };
+
+ ohci@60000 {
+ compatible = "snps,hsdk-v1.0-ohci", "generic-ohci";
+ reg = <0x60000 0x100>;
+ interrupts = <15>;
+ };
+
+ ehci@40000 {
+ compatible = "snps,hsdk-v1.0-ehci", "generic-ehci";
+ reg = <0x40000 0x100>;
+ interrupts = <15>;
+ };
+
+ mmc@a000 {
+ compatible = "altr,socfpga-dw-mshc";
+ reg = <0xa000 0x400>;
+ num-slots = <1>;
+ fifo-depth = <16>;
+ card-detect-delay = <200>;
+ clocks = <&mmcclk_biu>, <&mmcclk_ciu>;
+ clock-names = "biu", "ciu";
+ interrupts = <12>;
+ bus-width = <4>;
+ };
+ };
+
+ memory@80000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GiB */
+ };
+};
diff --git a/arch/arc/boot/dts/nsim_hs.dts b/arch/arc/boot/dts/nsim_hs.dts
index 3772c40..8d787b2 100644
--- a/arch/arc/boot/dts/nsim_hs.dts
+++ b/arch/arc/boot/dts/nsim_hs.dts
@@ -18,7 +18,7 @@
memory {
device_type = "memory";
- /* CONFIG_LINUX_LINK_BASE needs to match low mem start */
+ /* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MB low mem */
0x1 0x00000000 0x0 0x40000000>; /* 1 GB highmem */
};
diff --git a/arch/arc/configs/hsdk_defconfig b/arch/arc/configs/hsdk_defconfig
new file mode 100644
index 0000000..9a3fcf4
--- /dev/null
+++ b/arch/arc/configs/hsdk_defconfig
@@ -0,0 +1,80 @@
+CONFIG_DEFAULT_HOSTNAME="ARCLinux"
+CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_PID_NS is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE="../../arc_initramfs_hs/"
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_ARC_SOC_HSDK=y
+CONFIG_ISA_ARCV2=y
+CONFIG_SMP=y
+CONFIG_LINUX_LINK_BASE=0x90000000
+CONFIG_LINUX_RAM_BASE=0x80000000
+CONFIG_ARC_BUILTIN_DTB_NAME="hsdk"
+CONFIG_PREEMPT=y
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_DEVTMPFS=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_MICREL_PHY=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_UDL=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_DW=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT3_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
+CONFIG_CRYPTO_ECHAINIV=y
diff --git a/arch/arc/include/asm/cache.h b/arch/arc/include/asm/cache.h
index 02fd1ce..8486f32 100644
--- a/arch/arc/include/asm/cache.h
+++ b/arch/arc/include/asm/cache.h
@@ -47,7 +47,8 @@
: "r"(data), "r"(ptr)); \
})
-#define ARCH_DMA_MINALIGN L1_CACHE_BYTES
+/* Largest line length for either L1 or L2 is 128 bytes */
+#define ARCH_DMA_MINALIGN 128
extern void arc_cache_init(void);
extern char *arc_cache_mumbojumbo(int cpu_id, char *buf, int len);
@@ -95,6 +96,8 @@ extern unsigned long perip_base, perip_end;
#define ARC_REG_SLC_CTRL 0x903
#define ARC_REG_SLC_FLUSH 0x904
#define ARC_REG_SLC_INVALIDATE 0x905
+#define ARC_AUX_SLC_IVDL 0x910
+#define ARC_AUX_SLC_FLDL 0x912
#define ARC_REG_SLC_RGN_START 0x914
#define ARC_REG_SLC_RGN_START1 0x915
#define ARC_REG_SLC_RGN_END 0x916
diff --git a/arch/arc/include/asm/entry-compact.h b/arch/arc/include/asm/entry-compact.h
index 14c310f..ec36d5b 100644
--- a/arch/arc/include/asm/entry-compact.h
+++ b/arch/arc/include/asm/entry-compact.h
@@ -192,6 +192,12 @@
PUSHAX lp_start
PUSHAX erbta
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ .word CTOP_INST_SCHD_RW
+ PUSHAX CTOP_AUX_GPA1
+ PUSHAX CTOP_AUX_EFLAGS
+#endif
+
lr r9, [ecr]
st r9, [sp, PT_event] /* EV_Trap expects r9 to have ECR */
.endm
@@ -208,6 +214,12 @@
* by hardware and that is not good.
*-------------------------------------------------------------*/
.macro EXCEPTION_EPILOGUE
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ .word CTOP_INST_SCHD_RW
+ POPAX CTOP_AUX_EFLAGS
+ POPAX CTOP_AUX_GPA1
+#endif
+
POPAX erbta
POPAX lp_start
POPAX lp_end
@@ -265,6 +277,12 @@
PUSHAX lp_end
PUSHAX lp_start
PUSHAX bta_l\LVL\()
+
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ .word CTOP_INST_SCHD_RW
+ PUSHAX CTOP_AUX_GPA1
+ PUSHAX CTOP_AUX_EFLAGS
+#endif
.endm
/*--------------------------------------------------------------
@@ -277,6 +295,12 @@
* by hardware and that is not good.
*-------------------------------------------------------------*/
.macro INTERRUPT_EPILOGUE LVL
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ .word CTOP_INST_SCHD_RW
+ POPAX CTOP_AUX_EFLAGS
+ POPAX CTOP_AUX_GPA1
+#endif
+
POPAX bta_l\LVL\()
POPAX lp_start
POPAX lp_end
diff --git a/arch/arc/include/asm/irqflags-arcv2.h b/arch/arc/include/asm/irqflags-arcv2.h
index a64c447..8a4f77e 100644
--- a/arch/arc/include/asm/irqflags-arcv2.h
+++ b/arch/arc/include/asm/irqflags-arcv2.h
@@ -47,9 +47,6 @@
#define ISA_INIT_STATUS_BITS (STATUS_IE_MASK | STATUS_AD_MASK | \
(ARCV2_IRQ_DEF_PRIO << 1))
-/* SLEEP needs default irq priority (<=) which can interrupt the doze */
-#define ISA_SLEEP_ARG (0x10 | ARCV2_IRQ_DEF_PRIO)
-
#ifndef __ASSEMBLY__
/*
diff --git a/arch/arc/include/asm/irqflags-compact.h b/arch/arc/include/asm/irqflags-compact.h
index 4c6eed8..fcb8017 100644
--- a/arch/arc/include/asm/irqflags-compact.h
+++ b/arch/arc/include/asm/irqflags-compact.h
@@ -43,8 +43,6 @@
#define ISA_INIT_STATUS_BITS STATUS_IE_MASK
-#define ISA_SLEEP_ARG 0x3
-
#ifndef __ASSEMBLY__
/******************************************************************
diff --git a/arch/arc/include/asm/page.h b/arch/arc/include/asm/page.h
index 296c342..109baa0 100644
--- a/arch/arc/include/asm/page.h
+++ b/arch/arc/include/asm/page.h
@@ -85,7 +85,7 @@ typedef pte_t * pgtable_t;
*/
#define virt_to_pfn(kaddr) (__pa(kaddr) >> PAGE_SHIFT)
-#define ARCH_PFN_OFFSET virt_to_pfn(CONFIG_LINUX_LINK_BASE)
+#define ARCH_PFN_OFFSET virt_to_pfn(CONFIG_LINUX_RAM_BASE)
#ifdef CONFIG_FLATMEM
#define pfn_valid(pfn) (((pfn) - ARCH_PFN_OFFSET) < max_mapnr)
diff --git a/arch/arc/include/asm/processor.h b/arch/arc/include/asm/processor.h
index 4104a08..d400a21 100644
--- a/arch/arc/include/asm/processor.h
+++ b/arch/arc/include/asm/processor.h
@@ -27,6 +27,13 @@ struct arc_fpu {
};
#endif
+#ifdef CONFIG_ARC_PLAT_EZNPS
+struct eznps_dp {
+ unsigned int eflags;
+ unsigned int gpa1;
+};
+#endif
+
/* Arch specific stuff which needs to be saved per task.
* However these items are not so important so as to earn a place in
* struct thread_info
@@ -38,6 +45,9 @@ struct thread_struct {
#ifdef CONFIG_ARC_FPU_SAVE_RESTORE
struct arc_fpu fpu;
#endif
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ struct eznps_dp dp;
+#endif
};
#define INIT_THREAD { \
diff --git a/arch/arc/include/asm/ptrace.h b/arch/arc/include/asm/ptrace.h
index 5297faa..5a8cb22 100644
--- a/arch/arc/include/asm/ptrace.h
+++ b/arch/arc/include/asm/ptrace.h
@@ -19,6 +19,11 @@
#ifdef CONFIG_ISA_ARCOMPACT
struct pt_regs {
+#ifdef CONFIG_ARC_PLAT_EZNPS
+ unsigned long eflags; /* Extended FLAGS */
+ unsigned long gpa1; /* General Purpose Aux */
+#endif
+
/* Real registers */
unsigned long bta; /* bta_l1, bta_l2, erbta */
diff --git a/arch/arc/include/asm/spinlock.h b/arch/arc/include/asm/spinlock.h
index a325e6a..47efc84 100644
--- a/arch/arc/include/asm/spinlock.h
+++ b/arch/arc/include/asm/spinlock.h
@@ -247,9 +247,15 @@ static inline void arch_spin_lock(arch_spinlock_t *lock)
__asm__ __volatile__(
"1: ex %0, [%1] \n"
+#ifdef CONFIG_EZNPS_MTM_EXT
+ " .word %3 \n"
+#endif
" breq %0, %2, 1b \n"
: "+&r" (val)
: "r"(&(lock->slock)), "ir"(__ARCH_SPIN_LOCK_LOCKED__)
+#ifdef CONFIG_EZNPS_MTM_EXT
+ , "i"(CTOP_INST_SCHD_RW)
+#endif
: "memory");
/*
@@ -291,6 +297,12 @@ static inline void arch_spin_unlock(arch_spinlock_t *lock)
*/
smp_mb();
+ /*
+ * EX is not really required here, a simple STore of 0 suffices.
+ * However this causes tasklist livelocks in SystemC based SMP virtual
+ * platforms where the systemc core scheduler uses EX as a cue for
+ * moving to next core. Do a git log of this file for details
+ */
__asm__ __volatile__(
" ex %0, [%1] \n"
: "+r" (val)
diff --git a/arch/arc/include/asm/switch_to.h b/arch/arc/include/asm/switch_to.h
index 1b171ab..f7d07fe 100644
--- a/arch/arc/include/asm/switch_to.h
+++ b/arch/arc/include/asm/switch_to.h
@@ -26,10 +26,19 @@ extern void fpu_save_restore(struct task_struct *p, struct task_struct *n);
#endif /* !CONFIG_ARC_FPU_SAVE_RESTORE */
+#ifdef CONFIG_ARC_PLAT_EZNPS
+extern void dp_save_restore(struct task_struct *p, struct task_struct *n);
+#define ARC_EZNPS_DP_PREV(p, n) dp_save_restore(p, n)
+#else
+#define ARC_EZNPS_DP_PREV(p, n)
+
+#endif /* !CONFIG_ARC_PLAT_EZNPS */
+
struct task_struct *__switch_to(struct task_struct *p, struct task_struct *n);
#define switch_to(prev, next, last) \
do { \
+ ARC_EZNPS_DP_PREV(prev, next); \
ARC_FPU_PREV(prev, next); \
last = __switch_to(prev, next);\
ARC_FPU_NEXT(next); \
diff --git a/arch/arc/kernel/devtree.c b/arch/arc/kernel/devtree.c
index 3b67f53..521ef35 100644
--- a/arch/arc/kernel/devtree.c
+++ b/arch/arc/kernel/devtree.c
@@ -29,8 +29,9 @@ static void __init arc_set_early_base_baud(unsigned long dt_root)
{
if (of_flat_dt_is_compatible(dt_root, "abilis,arc-tb10x"))
arc_base_baud = 166666666; /* Fixed 166.6MHz clk (TB10x) */
- else if (of_flat_dt_is_compatible(dt_root, "snps,arc-sdp"))
- arc_base_baud = 33333333; /* Fixed 33MHz clk (AXS10x) */
+ else if (of_flat_dt_is_compatible(dt_root, "snps,arc-sdp") ||
+ of_flat_dt_is_compatible(dt_root, "snps,hsdk"))
+ arc_base_baud = 33333333; /* Fixed 33MHz clk (AXS10x & HSDK) */
else if (of_flat_dt_is_compatible(dt_root, "ezchip,arc-nps"))
arc_base_baud = 800000000; /* Fixed 800MHz clk (NPS) */
else
diff --git a/arch/arc/kernel/entry-compact.S b/arch/arc/kernel/entry-compact.S
index 9211707..f285dbb 100644
--- a/arch/arc/kernel/entry-compact.S
+++ b/arch/arc/kernel/entry-compact.S
@@ -25,12 +25,12 @@
*
* vineetg: Nov 2009 (Everything needed for TIF_RESTORE_SIGMASK)
* -do_signal()invoked upon TIF_RESTORE_SIGMASK as well
- * -Wrappers for sys_{,rt_}sigsuspend() nolonger needed as they don't
+ * -Wrappers for sys_{,rt_}sigsuspend() no longer needed as they don't
* need ptregs anymore
*
* Vineetg: Oct 2009
* -In a rare scenario, Process gets a Priv-V exception and gets scheduled
- * out. Since we don't do FAKE RTIE for Priv-V, CPU excpetion state remains
+ * out. Since we don't do FAKE RTIE for Priv-V, CPU exception state remains
* active (AE bit enabled). This causes a double fault for a subseq valid
* exception. Thus FAKE RTIE needed in low level Priv-Violation handler.
* Instr Error could also cause similar scenario, so same there as well.
@@ -59,7 +59,7 @@
*/
#include <linux/errno.h>
-#include <linux/linkage.h> /* {EXTRY,EXIT} */
+#include <linux/linkage.h> /* {ENTRY,EXIT} */
#include <asm/entry.h>
#include <asm/irqflags.h>
@@ -80,8 +80,8 @@
.align 4
/* Each entry in the vector table must occupy 2 words. Since it is a jump
- * across sections (.vector to .text) we are gauranteed that 'j somewhere'
- * will use the 'j limm' form of the intrsuction as long as somewhere is in
+ * across sections (.vector to .text) we are guaranteed that 'j somewhere'
+ * will use the 'j limm' form of the instruction as long as somewhere is in
* a section other than .vector.
*/
@@ -105,13 +105,13 @@
; ******************** Exceptions **********************
VECTOR EV_MachineCheck ; 0x100, Fatal Machine check (0x20)
-VECTOR EV_TLBMissI ; 0x108, Intruction TLB miss (0x21)
+VECTOR EV_TLBMissI ; 0x108, Instruction TLB miss (0x21)
VECTOR EV_TLBMissD ; 0x110, Data TLB miss (0x22)
VECTOR EV_TLBProtV ; 0x118, Protection Violation (0x23)
; or Misaligned Access
VECTOR EV_PrivilegeV ; 0x120, Privilege Violation (0x24)
VECTOR EV_Trap ; 0x128, Trap exception (0x25)
-VECTOR EV_Extension ; 0x130, Extn Intruction Excp (0x26)
+VECTOR EV_Extension ; 0x130, Extn Instruction Excp (0x26)
.rept 24
VECTOR reserved ; Reserved Exceptions
@@ -199,7 +199,7 @@
; ---------------------------------------------
; User Mode Memory Bus Error Interrupt Handler
-; (Kernel mode memory errors handled via seperate exception vectors)
+; (Kernel mode memory errors handled via separate exception vectors)
; ---------------------------------------------
ENTRY(mem_service)
@@ -273,7 +273,7 @@
;------ (5) Type of Protection Violation? ----------
;
; ProtV Hardware Exception is triggered for Access Faults of 2 types
- ; -Access Violaton : 00_23_(00|01|02|03)_00
+ ; -Access Violation : 00_23_(00|01|02|03)_00
; x r w r+w
; -Unaligned Access : 00_23_04_00
;
@@ -327,7 +327,7 @@
.Lrestore_regs:
- # Interrpts are actually disabled from this point on, but will get
+ # Interrupts are actually disabled from this point on, but will get
# reenabled after we return from interrupt/exception.
# But irq tracer needs to be told now...
TRACE_ASM_IRQ_ENABLE
@@ -335,7 +335,7 @@
lr r10, [status32]
; Restore REG File. In case multiple Events outstanding,
- ; use the same priorty as rtie: EXCPN, L2 IRQ, L1 IRQ, None
+ ; use the same priority as rtie: EXCPN, L2 IRQ, L1 IRQ, None
; Note that we use realtime STATUS32 (not pt_regs->status32) to
; decide that.
diff --git a/arch/arc/kernel/entry.S b/arch/arc/kernel/entry.S
index 1eea99b..85d9ea4 100644
--- a/arch/arc/kernel/entry.S
+++ b/arch/arc/kernel/entry.S
@@ -92,6 +92,12 @@
lr r0, [efa]
mov r1, sp
+ ; hardware auto-disables MMU, re-enable it to allow kernel vaddr
+ ; access for say stack unwinding of modules for crash dumps
+ lr r3, [ARC_REG_PID]
+ or r3, r3, MMU_ENABLE
+ sr r3, [ARC_REG_PID]
+
lsr r3, r2, 8
bmsk r3, r3, 7
brne r3, ECR_C_MCHK_DUP_TLB, 1f
diff --git a/arch/arc/kernel/process.c b/arch/arc/kernel/process.c
index 2a018de..5ac3b54 100644
--- a/arch/arc/kernel/process.c
+++ b/arch/arc/kernel/process.c
@@ -79,15 +79,40 @@ SYSCALL_DEFINE3(arc_usr_cmpxchg, int *, uaddr, int, expected, int, new)
return uval;
}
+#ifdef CONFIG_ISA_ARCV2
+
void arch_cpu_idle(void)
{
- /* sleep, but enable all interrupts before committing */
+ /* Re-enable interrupts <= default irq priority before commiting SLEEP */
+ const unsigned int arg = 0x10 | ARCV2_IRQ_DEF_PRIO;
+
__asm__ __volatile__(
"sleep %0 \n"
:
- :"I"(ISA_SLEEP_ARG)); /* can't be "r" has to be embedded const */
+ :"I"(arg)); /* can't be "r" has to be embedded const */
}
+#elif defined(CONFIG_EZNPS_MTM_EXT) /* ARC700 variant in NPS */
+
+void arch_cpu_idle(void)
+{
+ /* only the calling HW thread needs to sleep */
+ __asm__ __volatile__(
+ ".word %0 \n"
+ :
+ :"i"(CTOP_INST_HWSCHD_WFT_IE12));
+}
+
+#else /* ARC700 */
+
+void arch_cpu_idle(void)
+{
+ /* sleep, but enable both set E1/E2 (levels of interrutps) before committing */
+ __asm__ __volatile__("sleep 0x3 \n");
+}
+
+#endif
+
asmlinkage void ret_from_fork(void);
/*
@@ -209,6 +234,10 @@ void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long usp)
*/
regs->status32 = STATUS_U_MASK | STATUS_L_MASK | ISA_INIT_STATUS_BITS;
+#ifdef CONFIG_EZNPS_MTM_EXT
+ regs->eflags = 0;
+#endif
+
/* bogus seed values for debugging */
regs->lp_start = 0x10;
regs->lp_end = 0x80;
diff --git a/arch/arc/kernel/setup.c b/arch/arc/kernel/setup.c
index 666613f..c4ffb44 100644
--- a/arch/arc/kernel/setup.c
+++ b/arch/arc/kernel/setup.c
@@ -385,13 +385,13 @@ void setup_processor(void)
read_arc_build_cfg_regs();
arc_init_IRQ();
- printk(arc_cpu_mumbojumbo(cpu_id, str, sizeof(str)));
+ pr_info("%s", arc_cpu_mumbojumbo(cpu_id, str, sizeof(str)));
arc_mmu_init();
arc_cache_init();
- printk(arc_extn_mumbojumbo(cpu_id, str, sizeof(str)));
- printk(arc_platform_smp_cpuinfo());
+ pr_info("%s", arc_extn_mumbojumbo(cpu_id, str, sizeof(str)));
+ pr_info("%s", arc_platform_smp_cpuinfo());
arc_chk_core_config();
}
diff --git a/arch/arc/kernel/traps.c b/arch/arc/kernel/traps.c
index ff83e78..bcd7c9f 100644
--- a/arch/arc/kernel/traps.c
+++ b/arch/arc/kernel/traps.c
@@ -80,7 +80,7 @@ int name(unsigned long address, struct pt_regs *regs) \
DO_ERROR_INFO(SIGILL, "Priv Op/Disabled Extn", do_privilege_fault, ILL_PRVOPC)
DO_ERROR_INFO(SIGILL, "Invalid Extn Insn", do_extension_fault, ILL_ILLOPC)
DO_ERROR_INFO(SIGILL, "Illegal Insn (or Seq)", insterror_is_error, ILL_ILLOPC)
-DO_ERROR_INFO(SIGBUS, "Invalid Mem Access", do_memory_error, BUS_ADRERR)
+DO_ERROR_INFO(SIGBUS, "Invalid Mem Access", __weak do_memory_error, BUS_ADRERR)
DO_ERROR_INFO(SIGTRAP, "Breakpoint Set", trap_is_brkpt, TRAP_BRKPT)
DO_ERROR_INFO(SIGBUS, "Misaligned Access", do_misaligned_error, BUS_ADRALN)
@@ -103,7 +103,7 @@ int do_misaligned_access(unsigned long address, struct pt_regs *regs,
*/
void do_machine_check_fault(unsigned long address, struct pt_regs *regs)
{
- die("Machine Check Exception", regs, address);
+ die("Unhandled Machine Check Exception", regs, address);
}
diff --git a/arch/arc/kernel/troubleshoot.c b/arch/arc/kernel/troubleshoot.c
index f9caf79..7e94476 100644
--- a/arch/arc/kernel/troubleshoot.c
+++ b/arch/arc/kernel/troubleshoot.c
@@ -140,7 +140,7 @@ static void show_ecr_verbose(struct pt_regs *regs)
} else if (vec == ECR_V_ITLB_MISS) {
pr_cont("Insn could not be fetched\n");
} else if (vec == ECR_V_MACH_CHK) {
- pr_cont("%s\n", (cause_code == 0x0) ?
+ pr_cont("Machine Check (%s)\n", (cause_code == 0x0) ?
"Double Fault" : "Other Fatal Err");
} else if (vec == ECR_V_PROTV) {
@@ -233,6 +233,9 @@ void show_kernel_fault_diag(const char *str, struct pt_regs *regs,
{
current->thread.fault_address = address;
+ /* Show fault description */
+ pr_info("\n%s\n", str);
+
/* Caller and Callee regs */
show_regs(regs);
diff --git a/arch/arc/mm/cache.c b/arch/arc/mm/cache.c
index 7db283b..eee924d 100644
--- a/arch/arc/mm/cache.c
+++ b/arch/arc/mm/cache.c
@@ -652,7 +652,7 @@ static void __ic_line_inv_vaddr(phys_addr_t paddr, unsigned long vaddr,
#endif /* CONFIG_ARC_HAS_ICACHE */
-noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op)
+noinline void slc_op_rgn(phys_addr_t paddr, unsigned long sz, const int op)
{
#ifdef CONFIG_ISA_ARCV2
/*
@@ -715,6 +715,58 @@ noinline void slc_op(phys_addr_t paddr, unsigned long sz, const int op)
#endif
}
+noinline void slc_op_line(phys_addr_t paddr, unsigned long sz, const int op)
+{
+#ifdef CONFIG_ISA_ARCV2
+ /*
+ * SLC is shared between all cores and concurrent aux operations from
+ * multiple cores need to be serialized using a spinlock
+ * A concurrent operation can be silently ignored and/or the old/new
+ * operation can remain incomplete forever (lockup in SLC_CTRL_BUSY loop
+ * below)
+ */
+ static DEFINE_SPINLOCK(lock);
+
+ const unsigned long SLC_LINE_MASK = ~(l2_line_sz - 1);
+ unsigned int ctrl, cmd;
+ unsigned long flags;
+ int num_lines;
+
+ spin_lock_irqsave(&lock, flags);
+
+ ctrl = read_aux_reg(ARC_REG_SLC_CTRL);
+
+ /* Don't rely on default value of IM bit */
+ if (!(op & OP_FLUSH)) /* i.e. OP_INV */
+ ctrl &= ~SLC_CTRL_IM; /* clear IM: Disable flush before Inv */
+ else
+ ctrl |= SLC_CTRL_IM;
+
+ write_aux_reg(ARC_REG_SLC_CTRL, ctrl);
+
+ cmd = op & OP_INV ? ARC_AUX_SLC_IVDL : ARC_AUX_SLC_FLDL;
+
+ sz += paddr & ~SLC_LINE_MASK;
+ paddr &= SLC_LINE_MASK;
+
+ num_lines = DIV_ROUND_UP(sz, l2_line_sz);
+
+ while (num_lines-- > 0) {
+ write_aux_reg(cmd, paddr);
+ paddr += l2_line_sz;
+ }
+
+ /* Make sure "busy" bit reports correct stataus, see STAR 9001165532 */
+ read_aux_reg(ARC_REG_SLC_CTRL);
+
+ while (read_aux_reg(ARC_REG_SLC_CTRL) & SLC_CTRL_BUSY);
+
+ spin_unlock_irqrestore(&lock, flags);
+#endif
+}
+
+#define slc_op(paddr, sz, op) slc_op_rgn(paddr, sz, op)
+
noinline static void slc_entire_op(const int op)
{
unsigned int ctrl, r = ARC_REG_SLC_CTRL;
@@ -1095,7 +1147,7 @@ SYSCALL_DEFINE3(cacheflush, uint32_t, start, uint32_t, sz, uint32_t, flags)
*/
noinline void __init arc_ioc_setup(void)
{
- unsigned int ap_sz;
+ unsigned int ioc_base, mem_sz;
/* Flush + invalidate + disable L1 dcache */
__dc_disable();
@@ -1104,18 +1156,29 @@ noinline void __init arc_ioc_setup(void)
if (read_aux_reg(ARC_REG_SLC_BCR))
slc_entire_op(OP_FLUSH_N_INV);
- /* IOC Aperture start: TDB: handle non default CONFIG_LINUX_LINK_BASE */
- write_aux_reg(ARC_REG_IO_COH_AP0_BASE, 0x80000);
-
/*
- * IOC Aperture size:
- * decoded as 2 ^ (SIZE + 2) KB: so setting 0x11 implies 512M
+ * currently IOC Aperture covers entire DDR
* TBD: fix for PGU + 1GB of low mem
* TBD: fix for PAE
*/
- ap_sz = order_base_2(arc_get_mem_sz()/1024) - 2;
- write_aux_reg(ARC_REG_IO_COH_AP0_SIZE, ap_sz);
+ mem_sz = arc_get_mem_sz();
+ if (!is_power_of_2(mem_sz) || mem_sz < 4096)
+ panic("IOC Aperture size must be power of 2 larger than 4KB");
+
+ /*
+ * IOC Aperture size decoded as 2 ^ (SIZE + 2) KB,
+ * so setting 0x11 implies 512MB, 0x12 implies 1GB...
+ */
+ write_aux_reg(ARC_REG_IO_COH_AP0_SIZE, order_base_2(mem_sz >> 10) - 2);
+
+ /* for now assume kernel base is start of IOC aperture */
+ ioc_base = CONFIG_LINUX_RAM_BASE;
+
+ if (ioc_base % mem_sz != 0)
+ panic("IOC Aperture start must be aligned to the size of the aperture");
+
+ write_aux_reg(ARC_REG_IO_COH_AP0_BASE, ioc_base >> 12);
write_aux_reg(ARC_REG_IO_COH_PARTIAL, 1);
write_aux_reg(ARC_REG_IO_COH_ENABLE, 1);
@@ -1207,7 +1270,7 @@ void __ref arc_cache_init(void)
unsigned int __maybe_unused cpu = smp_processor_id();
char str[256];
- printk(arc_cache_mumbojumbo(0, str, sizeof(str)));
+ pr_info("%s", arc_cache_mumbojumbo(0, str, sizeof(str)));
if (!cpu)
arc_cache_init_master();
diff --git a/arch/arc/mm/fault.c b/arch/arc/mm/fault.c
index 162c975..a0b7bd6 100644
--- a/arch/arc/mm/fault.c
+++ b/arch/arc/mm/fault.c
@@ -207,7 +207,7 @@ void do_page_fault(unsigned long address, struct pt_regs *regs)
/* Are we prepared to handle this kernel fault?
*
* (The kernel has valid exception-points in the source
- * when it acesses user-memory. When it fails in one
+ * when it accesses user-memory. When it fails in one
* of those points, we find it in a table and do a jump
* to some fixup code that loads an appropriate error
* code)
diff --git a/arch/arc/mm/init.c b/arch/arc/mm/init.c
index 8c9415e..ba14506 100644
--- a/arch/arc/mm/init.c
+++ b/arch/arc/mm/init.c
@@ -26,7 +26,7 @@ pgd_t swapper_pg_dir[PTRS_PER_PGD] __aligned(PAGE_SIZE);
char empty_zero_page[PAGE_SIZE] __aligned(PAGE_SIZE);
EXPORT_SYMBOL(empty_zero_page);
-static const unsigned long low_mem_start = CONFIG_LINUX_LINK_BASE;
+static const unsigned long low_mem_start = CONFIG_LINUX_RAM_BASE;
static unsigned long low_mem_sz;
#ifdef CONFIG_HIGHMEM
@@ -63,7 +63,7 @@ void __init early_init_dt_add_memory_arch(u64 base, u64 size)
if (!low_mem_sz) {
if (base != low_mem_start)
- panic("CONFIG_LINUX_LINK_BASE != DT memory { }");
+ panic("CONFIG_LINUX_RAM_BASE != DT memory { }");
low_mem_sz = size;
in_use = 1;
@@ -161,7 +161,7 @@ void __init setup_arch_memory(void)
* We can't use the helper free_area_init(zones[]) because it uses
* PAGE_OFFSET to compute the @min_low_pfn which would be wrong
* when our kernel doesn't start at PAGE_OFFSET, i.e.
- * PAGE_OFFSET != CONFIG_LINUX_LINK_BASE
+ * PAGE_OFFSET != CONFIG_LINUX_RAM_BASE
*/
free_area_init_node(0, /* node-id */
zones_size, /* num pages per zone */
diff --git a/arch/arc/mm/tlb.c b/arch/arc/mm/tlb.c
index b181f3e..8ceefbf 100644
--- a/arch/arc/mm/tlb.c
+++ b/arch/arc/mm/tlb.c
@@ -821,7 +821,7 @@ void arc_mmu_init(void)
char str[256];
struct cpuinfo_arc_mmu *mmu = &cpuinfo_arc700[smp_processor_id()].mmu;
- printk(arc_mmu_mumbojumbo(0, str, sizeof(str)));
+ pr_info("%s", arc_mmu_mumbojumbo(0, str, sizeof(str)));
/*
* Can't be done in processor.h due to header include depenedencies
@@ -908,9 +908,6 @@ void do_tlb_overlap_fault(unsigned long cause, unsigned long address,
local_irq_save(flags);
- /* re-enable the MMU */
- write_aux_reg(ARC_REG_PID, MMU_ENABLE | read_aux_reg(ARC_REG_PID));
-
/* loop thru all sets of TLB */
for (set = 0; set < mmu->sets; set++) {
diff --git a/arch/arc/mm/tlbex.S b/arch/arc/mm/tlbex.S
index b30e4e3..0e1e47a 100644
--- a/arch/arc/mm/tlbex.S
+++ b/arch/arc/mm/tlbex.S
@@ -274,6 +274,13 @@
.macro COMMIT_ENTRY_TO_MMU
#if (CONFIG_ARC_MMU_VER < 4)
+#ifdef CONFIG_EZNPS_MTM_EXT
+ /* verify if entry for this vaddr+ASID already exists */
+ sr TLBProbe, [ARC_REG_TLBCOMMAND]
+ lr r0, [ARC_REG_TLBINDEX]
+ bbit0 r0, 31, 88f
+#endif
+
/* Get free TLB slot: Set = computed from vaddr, way = random */
sr TLBGetIndex, [ARC_REG_TLBCOMMAND]
@@ -287,6 +294,8 @@
#else
sr TLBInsertEntry, [ARC_REG_TLBCOMMAND]
#endif
+
+88:
.endm
diff --git a/arch/arc/plat-axs10x/axs10x.c b/arch/arc/plat-axs10x/axs10x.c
index 38ff349..f1ac679 100644
--- a/arch/arc/plat-axs10x/axs10x.c
+++ b/arch/arc/plat-axs10x/axs10x.c
@@ -80,22 +80,6 @@ static void __init axs10x_enable_gpio_intc_wire(void)
iowrite32(1 << MB_TO_GPIO_IRQ, (void __iomem *) GPIO_INTEN);
}
-static inline void __init
-write_cgu_reg(uint32_t value, void __iomem *reg, void __iomem *lock_reg)
-{
- unsigned int loops = 128 * 1024, ctr;
-
- iowrite32(value, reg);
-
- ctr = loops;
- while (((ioread32(lock_reg) & 1) == 1) && ctr--) /* wait for unlock */
- cpu_relax();
-
- ctr = loops;
- while (((ioread32(lock_reg) & 1) == 0) && ctr--) /* wait for re-lock */
- cpu_relax();
-}
-
static void __init axs10x_print_board_ver(unsigned int creg, const char *str)
{
union ver {
@@ -314,7 +298,6 @@ static void __init axs101_early_init(void)
#ifdef CONFIG_AXS103
-#define AXC003_CGU 0xF0000000
#define AXC003_CREG 0xF0001000
#define AXC003_MST_AXI_TUNNEL 0
#define AXC003_MST_HS38 1
@@ -324,131 +307,38 @@ static void __init axs101_early_init(void)
#define CREG_CPU_TUN_IO_CTRL (AXC003_CREG + 0x494)
-union pll_reg {
- struct {
-#ifdef CONFIG_CPU_BIG_ENDIAN
- unsigned int pad:17, noupd:1, bypass:1, edge:1, high:6, low:6;
-#else
- unsigned int low:6, high:6, edge:1, bypass:1, noupd:1, pad:17;
-#endif
- };
- unsigned int val;
-};
-
-static unsigned int __init axs103_get_freq(void)
-{
- union pll_reg idiv, fbdiv, odiv;
- unsigned int f = 33333333;
-
- idiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 0);
- fbdiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 4);
- odiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 8);
-
- if (idiv.bypass != 1)
- f = f / (idiv.low + idiv.high);
-
- if (fbdiv.bypass != 1)
- f = f * (fbdiv.low + fbdiv.high);
-
- if (odiv.bypass != 1)
- f = f / (odiv.low + odiv.high);
-
- f = (f + 500000) / 1000000; /* Rounding */
- return f;
-}
-
-static inline unsigned int __init encode_div(unsigned int id, int upd)
-{
- union pll_reg div;
-
- div.val = 0;
-
- div.noupd = !upd;
- div.bypass = id == 1 ? 1 : 0;
- div.edge = (id%2 == 0) ? 0 : 1; /* 0 = rising */
- div.low = (id%2 == 0) ? id >> 1 : (id >> 1)+1;
- div.high = id >> 1;
-
- return div.val;
-}
-
-noinline static void __init
-axs103_set_freq(unsigned int id, unsigned int fd, unsigned int od)
-{
- write_cgu_reg(encode_div(id, 0),
- (void __iomem *)AXC003_CGU + 0x80 + 0,
- (void __iomem *)AXC003_CGU + 0x110);
-
- write_cgu_reg(encode_div(fd, 0),
- (void __iomem *)AXC003_CGU + 0x80 + 4,
- (void __iomem *)AXC003_CGU + 0x110);
-
- write_cgu_reg(encode_div(od, 1),
- (void __iomem *)AXC003_CGU + 0x80 + 8,
- (void __iomem *)AXC003_CGU + 0x110);
-}
-
static void __init axs103_early_init(void)
{
- int offset = fdt_path_offset(initial_boot_params, "/cpu_card/core_clk");
- const struct fdt_property *prop = fdt_get_property(initial_boot_params,
- offset,
- "clock-frequency",
- NULL);
- u32 freq = be32_to_cpu(*(u32*)(prop->data)) / 1000000, orig = freq;
-
+#ifdef CONFIG_ARC_MCIP
/*
* AXS103 configurations for SMP/QUAD configurations share device tree
- * which defaults to 90 MHz. However recent failures of Quad config
+ * which defaults to 100 MHz. However recent failures of Quad config
* revealed P&R timing violations so clamp it down to safe 50 MHz
* Instead of duplicating defconfig/DT for SMP/QUAD, add a small hack
- *
- * This hack is really hacky as of now. Fix it properly by getting the
- * number of cores as return value of platform's early SMP callback
+ * of fudging the freq in DT
*/
-#ifdef CONFIG_ARC_MCIP
unsigned int num_cores = (read_aux_reg(ARC_REG_MCIP_BCR) >> 16) & 0x3F;
- if (num_cores > 2)
- freq = 50;
-#endif
-
- switch (freq) {
- case 33:
- axs103_set_freq(1, 1, 1);
- break;
- case 50:
- axs103_set_freq(1, 30, 20);
- break;
- case 75:
- axs103_set_freq(2, 45, 10);
- break;
- case 90:
- axs103_set_freq(2, 54, 10);
- break;
- case 100:
- axs103_set_freq(1, 30, 10);
- break;
- case 125:
- axs103_set_freq(2, 45, 6);
- break;
- default:
+ if (num_cores > 2) {
+ u32 freq = 50, orig;
/*
- * In this case, core_frequency derived from
- * DT "clock-frequency" might not match with board value.
- * Hence update it to match the board value.
+ * TODO: use cpu node "cpu-freq" param instead of platform-specific
+ * "/cpu_card/core_clk" as it works only if we use fixed-clock for cpu.
*/
- freq = axs103_get_freq();
- break;
- }
+ int off = fdt_path_offset(initial_boot_params, "/cpu_card/core_clk");
+ const struct fdt_property *prop;
- pr_info("Freq is %dMHz\n", freq);
+ prop = fdt_get_property(initial_boot_params, off,
+ "clock-frequency", NULL);
+ orig = be32_to_cpu(*(u32*)(prop->data)) / 1000000;
- /* Patching .dtb in-place with new core clock value */
- if (freq != orig ) {
- freq = cpu_to_be32(freq * 1000000);
- fdt_setprop_inplace(initial_boot_params, offset,
- "clock-frequency", &freq, sizeof(freq));
+ /* Patching .dtb in-place with new core clock value */
+ if (freq != orig ) {
+ freq = cpu_to_be32(freq * 1000000);
+ fdt_setprop_inplace(initial_boot_params, off,
+ "clock-frequency", &freq, sizeof(freq));
+ }
}
+#endif
/* Memory maps already config in pre-bootloader */
diff --git a/arch/arc/plat-eznps/Kconfig b/arch/arc/plat-eznps/Kconfig
index 1595a38..e151e20 100644
--- a/arch/arc/plat-eznps/Kconfig
+++ b/arch/arc/plat-eznps/Kconfig
@@ -12,8 +12,8 @@
help
Support for EZchip development platforms,
based on ARC700 cores.
- We handle few flavours:
- - Hardware Emulator AKA HE which is FPGA based chasis
+ We handle few flavors:
+ - Hardware Emulator AKA HE which is FPGA based chassis
- Simulator based on MetaWare nSIM
- NPS400 chip based on ASIC
@@ -32,3 +32,25 @@
any of them seem like CPU from Linux point of view.
All threads within same core share the execution unit of the
core and HW scheduler round robin between them.
+
+config EZNPS_MEM_ERROR_ALIGN
+ bool "ARC-EZchip Memory error as an exception"
+ depends on EZNPS_MTM_EXT
+ default n
+ help
+ On the real chip of the NPS, user memory errors are handled
+ as a machine check exception, which is fatal, whereas on
+ simulator platform for NPS, is handled as a Level 2 interrupt
+ (just a stock ARC700) which is recoverable. This option makes
+ simulator behave like hardware.
+
+config EZNPS_SHARED_AUX_REGS
+ bool "ARC-EZchip Shared Auxiliary Registers Per Core"
+ depends on ARC_PLAT_EZNPS
+ default y
+ help
+ On the real chip of the NPS, auxiliary registers are shared between
+ all the cpus of the core, whereas on simulator platform for NPS,
+ each cpu has a different set of auxiliary registers. Configuration
+ should be unset if auxiliary registers are not shared between the cpus
+ of the core, so there will be a need to initialize them per cpu.
diff --git a/arch/arc/plat-eznps/Makefile b/arch/arc/plat-eznps/Makefile
index 21091b1..8d43717 100644
--- a/arch/arc/plat-eznps/Makefile
+++ b/arch/arc/plat-eznps/Makefile
@@ -2,6 +2,6 @@
# Makefile for the linux kernel.
#
-obj-y := entry.o platform.o
+obj-y := entry.o platform.o ctop.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_EZNPS_MTM_EXT) += mtm.o
diff --git a/arch/arc/plat-eznps/ctop.c b/arch/arc/plat-eznps/ctop.c
new file mode 100644
index 0000000..030bcd0
--- /dev/null
+++ b/arch/arc/plat-eznps/ctop.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright(c) 2015 EZchip Technologies.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ */
+
+#include <linux/sched.h>
+#include <asm/processor.h>
+#include <plat/ctop.h>
+
+void dp_save_restore(struct task_struct *prev, struct task_struct *next)
+{
+ struct eznps_dp *prev_task_dp = &prev->thread.dp;
+ struct eznps_dp *next_task_dp = &next->thread.dp;
+
+ /* Here we save all Data Plane related auxiliary registers */
+ prev_task_dp->eflags = read_aux_reg(CTOP_AUX_EFLAGS);
+ write_aux_reg(CTOP_AUX_EFLAGS, next_task_dp->eflags);
+
+ prev_task_dp->gpa1 = read_aux_reg(CTOP_AUX_GPA1);
+ write_aux_reg(CTOP_AUX_GPA1, next_task_dp->gpa1);
+}
diff --git a/arch/arc/plat-eznps/entry.S b/arch/arc/plat-eznps/entry.S
index 328261c..091c92c 100644
--- a/arch/arc/plat-eznps/entry.S
+++ b/arch/arc/plat-eznps/entry.S
@@ -27,7 +27,7 @@
.align 1024 ; HW requierment for restart first PC
ENTRY(res_service)
-#ifdef CONFIG_EZNPS_MTM_EXT
+#if defined(CONFIG_EZNPS_MTM_EXT) && defined(CONFIG_EZNPS_SHARED_AUX_REGS)
; There is no work for HW thread id != 0
lr r3, [CTOP_AUX_THREAD_ID]
cmp r3, 0
diff --git a/arch/arc/plat-eznps/include/plat/ctop.h b/arch/arc/plat-eznps/include/plat/ctop.h
index ee2e32d..0c7d110 100644
--- a/arch/arc/plat-eznps/include/plat/ctop.h
+++ b/arch/arc/plat-eznps/include/plat/ctop.h
@@ -39,6 +39,7 @@
#define CTOP_AUX_LOGIC_CORE_ID (CTOP_AUX_BASE + 0x018)
#define CTOP_AUX_MT_CTRL (CTOP_AUX_BASE + 0x020)
#define CTOP_AUX_HW_COMPLY (CTOP_AUX_BASE + 0x024)
+#define CTOP_AUX_DPC (CTOP_AUX_BASE + 0x02C)
#define CTOP_AUX_LPC (CTOP_AUX_BASE + 0x030)
#define CTOP_AUX_EFLAGS (CTOP_AUX_BASE + 0x080)
#define CTOP_AUX_IACK (CTOP_AUX_BASE + 0x088)
@@ -46,6 +47,7 @@
#define CTOP_AUX_UDMC (CTOP_AUX_BASE + 0x300)
/* EZchip core instructions */
+#define CTOP_INST_HWSCHD_WFT_IE12 0x3E6F7344
#define CTOP_INST_HWSCHD_OFF_R4 0x3C6F00BF
#define CTOP_INST_HWSCHD_RESTORE_R4 0x3E6F7103
#define CTOP_INST_SCHD_RW 0x3E6F7004
diff --git a/arch/arc/plat-eznps/mtm.c b/arch/arc/plat-eznps/mtm.c
index aaaaffd..2388de3 100644
--- a/arch/arc/plat-eznps/mtm.c
+++ b/arch/arc/plat-eznps/mtm.c
@@ -21,10 +21,22 @@
#include <plat/mtm.h>
#include <plat/smp.h>
-#define MT_CTRL_HS_CNT 0xFF
+#define MT_HS_CNT_MIN 0x01
+#define MT_HS_CNT_MAX 0xFF
#define MT_CTRL_ST_CNT 0xF
#define NPS_NUM_HW_THREADS 0x10
+static int mtm_hs_ctr = MT_HS_CNT_MAX;
+
+#ifdef CONFIG_EZNPS_MEM_ERROR_ALIGN
+int do_memory_error(unsigned long address, struct pt_regs *regs)
+{
+ die("Invalid Mem Access", regs, address);
+
+ return 1;
+}
+#endif
+
static void mtm_init_nat(int cpu)
{
struct nps_host_reg_mtm_cfg mtm_cfg;
@@ -98,6 +110,18 @@ void mtm_enable_core(unsigned int cpu)
int i;
struct nps_host_reg_aux_mt_ctrl mt_ctrl;
struct nps_host_reg_mtm_cfg mtm_cfg;
+ struct nps_host_reg_aux_dpc dpc;
+
+ /*
+ * Initializing dpc register in each CPU.
+ * Overwriting the init value of the DPC
+ * register so that CMEM and FMT virtual address
+ * spaces are accessible, and Data Plane HW
+ * facilities are enabled.
+ */
+ dpc.ien = 1;
+ dpc.men = 1;
+ write_aux_reg(CTOP_AUX_DPC, dpc.value);
if (NPS_CPU_TO_THREAD_NUM(cpu) != 0)
return;
@@ -118,9 +142,7 @@ void mtm_enable_core(unsigned int cpu)
/* Enable HW schedule, stall counter, mtm */
mt_ctrl.value = 0;
mt_ctrl.hsen = 1;
- mt_ctrl.hs_cnt = MT_CTRL_HS_CNT;
- mt_ctrl.sten = 1;
- mt_ctrl.st_cnt = MT_CTRL_ST_CNT;
+ mt_ctrl.hs_cnt = mtm_hs_ctr;
mt_ctrl.mten = 1;
write_aux_reg(CTOP_AUX_MT_CTRL, mt_ctrl.value);
@@ -131,3 +153,23 @@ void mtm_enable_core(unsigned int cpu)
*/
cpu_relax();
}
+
+/* Verify and set the value of the mtm hs counter */
+static int __init set_mtm_hs_ctr(char *ctr_str)
+{
+ long hs_ctr;
+ int ret;
+
+ ret = kstrtol(ctr_str, 0, &hs_ctr);
+
+ if (ret || hs_ctr > MT_HS_CNT_MAX || hs_ctr < MT_HS_CNT_MIN) {
+ pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
+ hs_ctr, MT_HS_CNT_MIN, MT_HS_CNT_MAX);
+ return -EINVAL;
+ }
+
+ mtm_hs_ctr = hs_ctr;
+
+ return 0;
+}
+early_param("nps_mtm_hs_ctr", set_mtm_hs_ctr);
diff --git a/arch/arc/plat-hsdk/Kconfig b/arch/arc/plat-hsdk/Kconfig
new file mode 100644
index 0000000..5a6ed5a
--- /dev/null
+++ b/arch/arc/plat-hsdk/Kconfig
@@ -0,0 +1,9 @@
+# Copyright (C) 2017 Synopsys, Inc. (www.synopsys.com)
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License version 2 as
+# published by the Free Software Foundation.
+#
+
+menuconfig ARC_SOC_HSDK
+ bool "ARC HS Development Kit SOC"
diff --git a/arch/arc/plat-hsdk/Makefile b/arch/arc/plat-hsdk/Makefile
new file mode 100644
index 0000000..9a50c51
--- /dev/null
+++ b/arch/arc/plat-hsdk/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2017 Synopsys, Inc. (www.synopsys.com)
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License version 2 as
+# published by the Free Software Foundation.
+#
+
+obj-y := platform.o
diff --git a/arch/arc/plat-hsdk/platform.c b/arch/arc/plat-hsdk/platform.c
new file mode 100644
index 0000000..a2e7fd1
--- /dev/null
+++ b/arch/arc/plat-hsdk/platform.c
@@ -0,0 +1,66 @@
+/*
+ * ARC HSDK Platform support code
+ *
+ * Copyright (C) 2017 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <asm/arcregs.h>
+#include <asm/io.h>
+#include <asm/mach_desc.h>
+
+#define ARC_CCM_UNUSED_ADDR 0x60000000
+
+static void __init hsdk_init_per_cpu(unsigned int cpu)
+{
+ /*
+ * By default ICCM is mapped to 0x7z while this area is used for
+ * kernel virtual mappings, so move it to currently unused area.
+ */
+ if (cpuinfo_arc700[cpu].iccm.sz)
+ write_aux_reg(ARC_REG_AUX_ICCM, ARC_CCM_UNUSED_ADDR);
+
+ /*
+ * By default DCCM is mapped to 0x8z while this area is used by kernel,
+ * so move it to currently unused area.
+ */
+ if (cpuinfo_arc700[cpu].dccm.sz)
+ write_aux_reg(ARC_REG_AUX_DCCM, ARC_CCM_UNUSED_ADDR);
+}
+
+#define ARC_PERIPHERAL_BASE 0xf0000000
+#define CREG_BASE (ARC_PERIPHERAL_BASE + 0x1000)
+#define CREG_PAE (CREG_BASE + 0x180)
+#define CREG_PAE_UPDATE (CREG_BASE + 0x194)
+
+static void __init hsdk_init_early(void)
+{
+ /*
+ * PAE remapping for DMA clients does not work due to an RTL bug, so
+ * CREG_PAE register must be programmed to all zeroes, otherwise it
+ * will cause problems with DMA to/from peripherals even if PAE40 is
+ * not used.
+ */
+
+ /* Default is 1, which means "PAE offset = 4GByte" */
+ writel_relaxed(0, (void __iomem *) CREG_PAE);
+
+ /* Really apply settings made above */
+ writel(1, (void __iomem *) CREG_PAE_UPDATE);
+}
+
+static const char *hsdk_compat[] __initconst = {
+ "snps,hsdk",
+ NULL,
+};
+
+MACHINE_START(SIMULATION, "hsdk")
+ .dt_compat = hsdk_compat,
+ .init_early = hsdk_init_early,
+ .init_per_cpu = hsdk_init_per_cpu,
+MACHINE_END