diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
index e3a7dca..89f2ef7 100644
--- a/drivers/net/cs89x0.c
+++ b/drivers/net/cs89x0.c
@@ -170,11 +170,7 @@
 /* The cs8900 has 4 IRQ pins, software selectable. cs8900_irq_map maps
    them to system IRQ numbers. This mapping is card specific and is set to
    the configuration of the Cirrus Eval board for this chip. */
-#if defined(CONFIG_SH_HICOSH4)
-static unsigned int netcard_portlist[] __used __initdata =
-   { 0x0300, 0};
-static unsigned int cs8900_irq_map[] = {1,0,0,0};
-#elif defined(CONFIG_MACH_IXDP2351)
+#if defined(CONFIG_MACH_IXDP2351)
 static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
 static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
 #elif defined(CONFIG_ARCH_IXDP2X01)
@@ -578,12 +574,6 @@
 		goto out1;
 	}
 
-#ifdef CONFIG_SH_HICOSH4
-	/* truly reset the chip */
-	writeword(ioaddr, ADD_PORT, 0x0114);
-	writeword(ioaddr, DATA_PORT, 0x0040);
-#endif
-
 	/* if they give us an odd I/O address, then do ONE write to
            the address port, to get it back to address zero, where we
            expect to find the EISA signature word. An IO with a base of 0x3
@@ -649,37 +639,6 @@
 	   the driver will always do *something* instead of complain that
 	   adapter_cnf is 0. */
 
-#ifdef CONFIG_SH_HICOSH4
-	if (1) {
-		/* For the HiCO.SH4 board, things are different: we don't
-		   have EEPROM, but there is some data in flash, so we go
-		   get it there directly (MAC). */
-		__u16 *confd;
-		short cnt;
-		if (((* (volatile __u32 *) 0xa0013ff0) & 0x00ffffff)
-			== 0x006c3000) {
-			confd = (__u16*) 0xa0013fc0;
-		} else {
-			confd = (__u16*) 0xa001ffc0;
-		}
-		cnt = (*confd++ & 0x00ff) >> 1;
-		while (--cnt > 0) {
-			__u16 j = *confd++;
-
-			switch (j & 0x0fff) {
-			case PP_IA:
-				for (i = 0; i < ETH_ALEN/2; i++) {
-					dev->dev_addr[i*2] = confd[i] & 0xFF;
-					dev->dev_addr[i*2+1] = confd[i] >> 8;
-				}
-				break;
-			}
-			j = (j >> 12) + 1;
-			confd += j;
-			cnt -= j;
-		}
-	} else
-#endif
 
         if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) ==
 	      (EEPROM_OK|EEPROM_PRESENT)) {
@@ -734,11 +693,7 @@
         printk("\n");
 
 	/* First check to see if an EEPROM is attached. */
-#ifdef CONFIG_SH_HICOSH4 /* no EEPROM on HiCO, don't hazzle with it here */
-	if (1) {
-		printk(KERN_NOTICE "cs89x0: No EEPROM on HiCO.SH4\n");
-	} else
-#endif
+
 	if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0)
 		printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n");
 	else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) {
@@ -1275,7 +1230,6 @@
 	int i;
 	int ret;
 
-#if !defined(CONFIG_SH_HICOSH4) && !defined(CONFIG_ARCH_PNX010X) /* uses irq#1, so this won't work */
 	if (dev->irq < 2) {
 		/* Allow interrupts to be generated by the chip */
 /* Cirrus' release had this: */
@@ -1304,7 +1258,6 @@
 		}
 	}
 	else
-#endif
 	{
 #ifndef CONFIG_CS89x0_NONISA_IRQ
 		if (((1 << dev->irq) & lp->irq_map) == 0) {