hwmon: (lm85) extend to support EMC6D103 chips
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 5eadb00..297bc9a 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -575,7 +575,7 @@
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
- EMC6D101 and EMC6D102.
+ EMC6D101, EMC6D102, and EMC6D103.
This driver can also be built as a module. If so, the module
will be called lm85.
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index 1e22984..d2cc286 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -41,7 +41,7 @@
enum chips {
any_chip, lm85b, lm85c,
adm1027, adt7463, adt7468,
- emc6d100, emc6d102
+ emc6d100, emc6d102, emc6d103
};
/* The LM85 registers */
@@ -90,6 +90,9 @@
#define LM85_VERSTEP_EMC6D100_A0 0x60
#define LM85_VERSTEP_EMC6D100_A1 0x61
#define LM85_VERSTEP_EMC6D102 0x65
+#define LM85_VERSTEP_EMC6D103_A0 0x68
+#define LM85_VERSTEP_EMC6D103_A1 0x69
+#define LM85_VERSTEP_EMC6D103S 0x6A /* Also known as EMC6D103:A2 */
#define LM85_REG_CONFIG 0x40
@@ -348,6 +351,7 @@
{ "emc6d100", emc6d100 },
{ "emc6d101", emc6d100 },
{ "emc6d102", emc6d102 },
+ { "emc6d103", emc6d103 },
{ }
};
MODULE_DEVICE_TABLE(i2c, lm85_id);
@@ -1250,6 +1254,20 @@
case LM85_VERSTEP_EMC6D102:
type_name = "emc6d102";
break;
+ case LM85_VERSTEP_EMC6D103_A0:
+ case LM85_VERSTEP_EMC6D103_A1:
+ type_name = "emc6d103";
+ break;
+ /*
+ * Registers apparently missing in EMC6D103S/EMC6D103:A2
+ * compared to EMC6D103:A0, EMC6D103:A1, and EMC6D102
+ * (according to the data sheets), but used unconditionally
+ * in the driver: 62[5:7], 6D[0:7], and 6E[0:7].
+ * So skip EMC6D103S for now.
+ case LM85_VERSTEP_EMC6D103S:
+ type_name = "emc6d103s";
+ break;
+ */
}
} else {
dev_dbg(&adapter->dev,
@@ -1283,6 +1301,7 @@
case adt7468:
case emc6d100:
case emc6d102:
+ case emc6d103:
data->freq_map = adm1027_freq_map;
break;
default:
@@ -1468,7 +1487,7 @@
/* More alarm bits */
data->alarms |= lm85_read_value(client,
EMC6D100_REG_ALARM3) << 16;
- } else if (data->type == emc6d102) {
+ } else if (data->type == emc6d102 || data->type == emc6d103) {
/* Have to read LSB bits after the MSB ones because
the reading of the MSB bits has frozen the
LSBs (backward from the ADM1027).