net: axienet: Handle jumbo frames for lesser frame sizes
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index b834253..b1081e1 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -471,14 +471,16 @@
__axienet_device_reset(lp, &ndev->dev, XAXIDMA_RX_CR_OFFSET);
lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
+ lp->options |= XAE_OPTION_VLAN;
lp->options &= (~XAE_OPTION_JUMBO);
if ((ndev->mtu > XAE_MTU) &&
- (ndev->mtu <= XAE_JUMBO_MTU) &&
- (lp->jumbo_support)) {
- lp->max_frm_size = ndev->mtu + XAE_HDR_VLAN_SIZE +
- XAE_TRL_SIZE;
- lp->options |= XAE_OPTION_JUMBO;
+ (ndev->mtu <= XAE_JUMBO_MTU)) {
+ lp->max_frm_size = ndev->mtu + VLAN_ETH_HLEN +
+ XAE_TRL_SIZE;
+
+ if (lp->max_frm_size <= lp->rxmem)
+ lp->options |= XAE_OPTION_JUMBO;
}
if (axienet_dma_bd_init(ndev)) {
@@ -1027,15 +1029,15 @@
if (netif_running(ndev))
return -EBUSY;
- if (lp->jumbo_support) {
- if ((new_mtu > XAE_JUMBO_MTU) || (new_mtu < 64))
- return -EINVAL;
- ndev->mtu = new_mtu;
- } else {
- if ((new_mtu > XAE_MTU) || (new_mtu < 64))
- return -EINVAL;
- ndev->mtu = new_mtu;
- }
+
+ if ((new_mtu + VLAN_ETH_HLEN +
+ XAE_TRL_SIZE) > lp->rxmem)
+ return -EINVAL;
+
+ if ((new_mtu > XAE_JUMBO_MTU) || (new_mtu < 64))
+ return -EINVAL;
+
+ ndev->mtu = new_mtu;
return 0;
}
@@ -1556,16 +1558,14 @@
}
}
/* For supporting jumbo frames, the Axi Ethernet hardware must have
- * a larger Rx/Tx Memory. Typically, the size must be more than or
- * equal to 16384 bytes, so that we can enable jumbo option and start
- * supporting jumbo frames. Here we check for memory allocated for
- * Rx/Tx in the hardware from the device-tree and accordingly set
- * flags. */
+ * a larger Rx/Tx Memory. Typically, the size must be large so that
+ * we can enable jumbo option and start supporting jumbo frames.
+ * Here we check for memory allocated for Rx/Tx in the hardware from
+ * the device-tree and accordingly set flags.
+ */
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,rxmem", NULL);
- if (p) {
- if ((be32_to_cpup(p)) >= 0x4000)
- lp->jumbo_support = 1;
- }
+ if (p)
+ lp->rxmem = be32_to_cpup(p);
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,phy-type", NULL);
if (p)
lp->phy_type = be32_to_cpup(p);