usb: musb: Use is_cppi_enabled() and tusb_dma_omap() instead of the ifdef
This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/musb/musb_gadget.c b/drivers/usb/musb/musb_gadget.c
index 96632f9..4376f51 100644
--- a/drivers/usb/musb/musb_gadget.c
+++ b/drivers/usb/musb/musb_gadget.c
@@ -357,47 +357,49 @@
}
}
-#elif defined(CONFIG_USB_TI_CPPI_DMA)
- /* program endpoint CSR first, then setup DMA */
- csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY);
- csr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_DMAMODE |
- MUSB_TXCSR_MODE;
- musb_writew(epio, MUSB_TXCSR,
- (MUSB_TXCSR_P_WZC_BITS & ~MUSB_TXCSR_P_UNDERRUN)
- | csr);
-
- /* ensure writebuffer is empty */
- csr = musb_readw(epio, MUSB_TXCSR);
-
- /* NOTE host side sets DMAENAB later than this; both are
- * OK since the transfer dma glue (between CPPI and Mentor
- * fifos) just tells CPPI it could start. Data only moves
- * to the USB TX fifo when both fifos are ready.
- */
-
- /* "mode" is irrelevant here; handle terminating ZLPs like
- * PIO does, since the hardware RNDIS mode seems unreliable
- * except for the last-packet-is-already-short case.
- */
- use_dma = use_dma && c->channel_program(
- musb_ep->dma, musb_ep->packet_sz,
- 0,
- request->dma + request->actual,
- request_size);
- if (!use_dma) {
- c->channel_release(musb_ep->dma);
- musb_ep->dma = NULL;
- csr &= ~MUSB_TXCSR_DMAENAB;
- musb_writew(epio, MUSB_TXCSR, csr);
- /* invariant: prequest->buf is non-null */
- }
-#elif defined(CONFIG_USB_TUSB_OMAP_DMA)
- use_dma = use_dma && c->channel_program(
- musb_ep->dma, musb_ep->packet_sz,
- request->zero,
- request->dma + request->actual,
- request_size);
#endif
+ if (is_cppi_enabled()) {
+ /* program endpoint CSR first, then setup DMA */
+ csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY);
+ csr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_DMAMODE |
+ MUSB_TXCSR_MODE;
+ musb_writew(epio, MUSB_TXCSR, (MUSB_TXCSR_P_WZC_BITS &
+ ~MUSB_TXCSR_P_UNDERRUN) | csr);
+
+ /* ensure writebuffer is empty */
+ csr = musb_readw(epio, MUSB_TXCSR);
+
+ /*
+ * NOTE host side sets DMAENAB later than this; both are
+ * OK since the transfer dma glue (between CPPI and
+ * Mentor fifos) just tells CPPI it could start. Data
+ * only moves to the USB TX fifo when both fifos are
+ * ready.
+ */
+ /*
+ * "mode" is irrelevant here; handle terminating ZLPs
+ * like PIO does, since the hardware RNDIS mode seems
+ * unreliable except for the
+ * last-packet-is-already-short case.
+ */
+ use_dma = use_dma && c->channel_program(
+ musb_ep->dma, musb_ep->packet_sz,
+ 0,
+ request->dma + request->actual,
+ request_size);
+ if (!use_dma) {
+ c->channel_release(musb_ep->dma);
+ musb_ep->dma = NULL;
+ csr &= ~MUSB_TXCSR_DMAENAB;
+ musb_writew(epio, MUSB_TXCSR, csr);
+ /* invariant: prequest->buf is non-null */
+ }
+ } else if (tusb_dma_omap())
+ use_dma = use_dma && c->channel_program(
+ musb_ep->dma, musb_ep->packet_sz,
+ request->zero,
+ request->dma + request->actual,
+ request_size);
}
#endif