ath9k: Fix RX filters in channel contexts
Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index 63fbc3e..68e56d6 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -387,7 +387,9 @@
if (sc->hw->conf.radar_enabled)
rfilt |= ATH9K_RX_FILTER_PHYRADAR | ATH9K_RX_FILTER_PHYERR;
- if (sc->rx.rxfilter & FIF_PROBE_REQ)
+ spin_lock_bh(&sc->chan_lock);
+
+ if (sc->cur_chan->rxfilter & FIF_PROBE_REQ)
rfilt |= ATH9K_RX_FILTER_PROBEREQ;
/*
@@ -398,24 +400,24 @@
if (sc->sc_ah->is_monitoring)
rfilt |= ATH9K_RX_FILTER_PROM;
- if (sc->rx.rxfilter & FIF_CONTROL)
+ if (sc->cur_chan->rxfilter & FIF_CONTROL)
rfilt |= ATH9K_RX_FILTER_CONTROL;
if ((sc->sc_ah->opmode == NL80211_IFTYPE_STATION) &&
(sc->nvifs <= 1) &&
- !(sc->rx.rxfilter & FIF_BCN_PRBRESP_PROMISC))
+ !(sc->cur_chan->rxfilter & FIF_BCN_PRBRESP_PROMISC))
rfilt |= ATH9K_RX_FILTER_MYBEACON;
else
rfilt |= ATH9K_RX_FILTER_BEACON;
if ((sc->sc_ah->opmode == NL80211_IFTYPE_AP) ||
- (sc->rx.rxfilter & FIF_PSPOLL))
+ (sc->cur_chan->rxfilter & FIF_PSPOLL))
rfilt |= ATH9K_RX_FILTER_PSPOLL;
if (sc->cur_chandef.width != NL80211_CHAN_WIDTH_20_NOHT)
rfilt |= ATH9K_RX_FILTER_COMP_BAR;
- if (sc->nvifs > 1 || (sc->rx.rxfilter & FIF_OTHER_BSS)) {
+ if (sc->nvifs > 1 || (sc->cur_chan->rxfilter & FIF_OTHER_BSS)) {
/* This is needed for older chips */
if (sc->sc_ah->hw_version.macVersion <= AR_SREV_VERSION_9160)
rfilt |= ATH9K_RX_FILTER_PROM;
@@ -429,6 +431,8 @@
test_bit(ATH_OP_SCANNING, &common->op_flags))
rfilt |= ATH9K_RX_FILTER_BEACON;
+ spin_unlock_bh(&sc->chan_lock);
+
return rfilt;
}
@@ -865,8 +869,13 @@
* everything but the rate is checked here, the rate check is done
* separately to avoid doing two lookups for a rate for each frame.
*/
- if (!ath9k_cmn_rx_accept(common, hdr, rx_status, rx_stats, decrypt_error, sc->rx.rxfilter))
+ spin_lock_bh(&sc->chan_lock);
+ if (!ath9k_cmn_rx_accept(common, hdr, rx_status, rx_stats, decrypt_error,
+ sc->cur_chan->rxfilter)) {
+ spin_unlock_bh(&sc->chan_lock);
return -EINVAL;
+ }
+ spin_unlock_bh(&sc->chan_lock);
if (ath_is_mybeacon(common, hdr)) {
RX_STAT_INC(rx_beacons);