arch/x86/include/asm/nospec-branch.h

/* SPDX-License-Identifier: GPL-2.0 */

#ifndef __NOSPEC_BRANCH_H__
#define __NOSPEC_BRANCH_H__

#include <asm/alternative.h>
#include <asm/alternative-asm.h>
#include <asm/cpufeatures.h>

#ifdef __ASSEMBLY__

/*
 * This should be used immediately before a retpoline alternative.  It tells
 * objtool where the retpolines are so that it can make sense of the control
 * flow by just reading the original instruction(s) and ignoring the
 * alternatives.
 */
.macro ANNOTATE_NOSPEC_ALTERNATIVE
	.Lannotate_\@:
	.pushsection .discard.nospec
	.long .Lannotate_\@ - .
	.popsection
.endm

/*
 * These are the bare retpoline primitives for indirect jmp and call.
 * Do not use these directly; they only exist to make the ALTERNATIVE
 * invocation below less ugly.
 */
.macro RETPOLINE_JMP reg:req
	call	.Ldo_rop_\@
.Lspec_trap_\@:
	pause
	jmp	.Lspec_trap_\@
.Ldo_rop_\@:
	mov	\reg, (%_ASM_SP)
	ret
.endm

/*
 * This is a wrapper around RETPOLINE_JMP so the called function in reg
 * returns to the instruction after the macro.
 */
.macro RETPOLINE_CALL reg:req
	jmp	.Ldo_call_\@
.Ldo_retpoline_jmp_\@:
	RETPOLINE_JMP \reg
.Ldo_call_\@:
	call	.Ldo_retpoline_jmp_\@
.endm

/*
 * JMP_NOSPEC and CALL_NOSPEC macros can be used instead of a simple
 * indirect jmp/call which may be susceptible to the Spectre variant 2
 * attack.
 */
.macro JMP_NOSPEC reg:req
#ifdef CONFIG_RETPOLINE
	ANNOTATE_NOSPEC_ALTERNATIVE
	ALTERNATIVE_2 __stringify(jmp *\reg),				\
		__stringify(RETPOLINE_JMP \reg), X86_FEATURE_RETPOLINE,	\
		__stringify(lfence; jmp *\reg), X86_FEATURE_RETPOLINE_AMD
#else
	jmp	*\reg
#endif
.endm

.macro CALL_NOSPEC reg:req
#ifdef CONFIG_RETPOLINE
	ANNOTATE_NOSPEC_ALTERNATIVE
	ALTERNATIVE_2 __stringify(call *\reg),				\
		__stringify(RETPOLINE_CALL \reg), X86_FEATURE_RETPOLINE,\
		__stringify(lfence; call *\reg), X86_FEATURE_RETPOLINE_AMD
#else
	call	*\reg
#endif
.endm

#else /* __ASSEMBLY__ */

#define ANNOTATE_NOSPEC_ALTERNATIVE				\
	"999:\n\t"						\
	".pushsection .discard.nospec\n\t"			\
	".long 999b - .\n\t"					\
	".popsection\n\t"

#if defined(CONFIG_X86_64) && defined(RETPOLINE)

/*
 * Since the inline asm uses the %V modifier which is only in newer GCC,
 * the 64-bit one is dependent on RETPOLINE not CONFIG_RETPOLINE.
 */
# define CALL_NOSPEC						\
	ANNOTATE_NOSPEC_ALTERNATIVE				\
	ALTERNATIVE(						\
	"call *%[thunk_target]\n",				\
	"call __x86_indirect_thunk_%V[thunk_target]\n",		\
	X86_FEATURE_RETPOLINE)
# define THUNK_TARGET(addr) [thunk_target] "r" (addr)

#elif defined(CONFIG_X86_32) && defined(CONFIG_RETPOLINE)
/*
 * For i386 we use the original ret-equivalent retpoline, because
 * otherwise we'll run out of registers. We don't care about CET
 * here, anyway.
 */
# define CALL_NOSPEC ALTERNATIVE("call *%[thunk_target]\n",	\
	"       jmp    904f;\n"					\
	"       .align 16\n"					\
	"901:	call   903f;\n"					\
	"902:	pause;\n"					\
	"       jmp    902b;\n"					\
	"       .align 16\n"					\
	"903:	addl   $4, %%esp;\n"				\
	"       pushl  %[thunk_target];\n"			\
	"       ret;\n"						\
	"       .align 16\n"					\
	"904:	call   901b;\n",				\
	X86_FEATURE_RETPOLINE)

# define THUNK_TARGET(addr) [thunk_target] "rm" (addr)
#else /* No retpoline */
# define CALL_NOSPEC "call *%[thunk_target]\n"
# define THUNK_TARGET(addr) [thunk_target] "rm" (addr)
#endif

/* The Spectre V2 mitigation variants */
enum spectre_v2_mitigation {
	SPECTRE_V2_NONE,
	SPECTRE_V2_RETPOLINE_MINIMAL,
	SPECTRE_V2_RETPOLINE_MINIMAL_AMD,
	SPECTRE_V2_RETPOLINE_GENERIC,
	SPECTRE_V2_RETPOLINE_AMD,
	SPECTRE_V2_IBRS,
};

#endif /* __ASSEMBLY__ */
#endif /* __NOSPEC_BRANCH_H__ */