drivers/net/wireless/iwlwifi/mvm/fw-api-power.h

/******************************************************************************
 *
 * This file is provided under a dual BSD/GPLv2 license.  When using or
 * redistributing this file, you may do so under either license.
 *
 * GPL LICENSE SUMMARY
 *
 * Copyright(c) 2012 - 2013 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
 * USA
 *
 * The full GNU General Public License is included in this distribution
 * in the file called COPYING.
 *
 * Contact Information:
 *  Intel Linux Wireless <ilw@linux.intel.com>
 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
 *
 * BSD LICENSE
 *
 * Copyright(c) 2012 - 2013 Intel Corporation. All rights reserved.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 *  * Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *  * Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 *  * Neither the name Intel Corporation nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 *****************************************************************************/

#ifndef __fw_api_power_h__
#define __fw_api_power_h__

/* Power Management Commands, Responses, Notifications */

/**
 * enum iwl_scan_flags - masks for power table command flags
 * @POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK: '0' Driver disables power management,
 *		'1' Driver enables PM (use rest of parameters)
 * @POWER_FLAGS_SLEEP_OVER_DTIM_MSK: '0' PM have to walk up every DTIM,
 *		'1' PM could sleep over DTIM till listen Interval.
 * @POWER_FLAGS_LPRX_ENA_MSK: Low Power RX enable.
 * @POWER_FLAGS_SNOOZE_ENA_MSK: Enable snoozing only if uAPSD is enabled and all
 *		access categories are both delivery and trigger enabled.
 * @POWER_FLAGS_BT_SCO_ENA: Enable BT SCO coex only if uAPSD and
 *		PBW Snoozing enabled
 * @POWER_FLAGS_ADVANCE_PM_ENA_MSK: Advanced PM (uAPSD) enable mask
*/
enum iwl_power_flags {
	POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK	= BIT(0),
	POWER_FLAGS_SLEEP_OVER_DTIM_MSK		= BIT(1),
	POWER_FLAGS_LPRX_ENA_MSK		= BIT(2),
	POWER_FLAGS_SNOOZE_ENA_MSK		= BIT(3),
	POWER_FLAGS_BT_SCO_ENA			= BIT(4),
	POWER_FLAGS_ADVANCE_PM_ENA_MSK		= BIT(5)
};

/**
 * struct iwl_powertable_cmd - Power Table Command
 * POWER_TABLE_CMD = 0x77 (command, has simple generic response)
 *
 * @id_and_color:	MAC contex identifier
 * @action:		Action on context - no action, add new,
 *			modify existent, remove
 * @flags:		Power table command flags from POWER_FLAGS_*
 * @keep_alive_seconds: Keep alive period in seconds. Default - 25 sec.
 *			Minimum allowed:- 3 * DTIM
 * @rx_data_timeout:    Minimum time (usec) from last Rx packet for AM to
 *			PSM transition - legacy PM
 * @tx_data_timeout:    Minimum time (usec) from last Tx packet for AM to
 *			PSM transition - legacy PM
 * @rx_data_timeout_uapsd: Minimum time (usec) from last Rx packet for AM to
 *			PSM transition - uAPSD
 * @tx_data_timeout_uapsd: Minimum time (usec) from last Tx packet for AM to
 *			PSM transition - uAPSD
 * @lprx_rssi_threshold: Signal strength up to which LP RX can be enabled.
 *			Default: 80dbm
 * @num_skip_dtim:      Number of DTIMs to skip if Skip over DTIM flag is set
 * @snooze_interval:    TBD
 * @snooze_window:      TBD
 * @snooze_step:        TBD
 * @qndp_tid:           TBD
 * @uapsd_ac_flags:     TBD
 * @uapsd_max_sp:       TBD
 */
struct iwl_powertable_cmd {
	/* COMMON_INDEX_HDR_API_S_VER_1 */
	__le32 id_and_color;
	__le32 action;
	__le16 flags;
	u8 reserved;
	__le16 keep_alive_seconds;
	__le32 rx_data_timeout;
	__le32 tx_data_timeout;
	__le32 rx_data_timeout_uapsd;
	__le32 tx_data_timeout_uapsd;
	u8 lprx_rssi_threshold;
	u8 num_skip_dtim;
	__le16 snooze_interval;
	__le16 snooze_window;
	u8 snooze_step;
	u8 qndp_tid;
	u8 uapsd_ac_flags;
	u8 uapsd_max_sp;
} __packed;

#endif