arch/sh/mm/Kconfig

menu "Processor selection"

#
# Processor families
#
config CPU_SH2
	select SH_WRITETHROUGH if !CPU_SH2A
	bool

config CPU_SH2A
	bool
	select CPU_SH2

config CPU_SH3
	bool
	select CPU_HAS_INTEVT
	select CPU_HAS_SR_RB

config CPU_SH4
	bool
	select CPU_HAS_INTEVT
	select CPU_HAS_SR_RB
	select CPU_HAS_PTEA if (!CPU_SUBTYPE_ST40 && !CPU_SH4A) || CPU_SHX2

config CPU_SH4A
	bool
	select CPU_SH4

config CPU_SH4AL_DSP
	bool
	select CPU_SH4A

config CPU_SUBTYPE_ST40
	bool
	select CPU_SH4
	select CPU_HAS_INTC2_IRQ

config CPU_SHX2
	bool

#
# Processor subtypes
#

comment "SH-2 Processor Support"

config CPU_SUBTYPE_SH7604
	bool "Support SH7604 processor"
	select CPU_SH2

config CPU_SUBTYPE_SH7619
	bool "Support SH7619 processor"
	select CPU_SH2

comment "SH-2A Processor Support"

config CPU_SUBTYPE_SH7206
	bool "Support SH7206 processor"
	select CPU_SH2A

comment "SH-3 Processor Support"

config CPU_SUBTYPE_SH7300
	bool "Support SH7300 processor"
	select CPU_SH3

config CPU_SUBTYPE_SH7705
	bool "Support SH7705 processor"
	select CPU_SH3
	select CPU_HAS_IPR_IRQ
	select CPU_HAS_PINT_IRQ

config CPU_SUBTYPE_SH7706
	bool "Support SH7706 processor"
	select CPU_SH3
	select CPU_HAS_IPR_IRQ
	help
	  Select SH7706 if you have a 133 Mhz SH-3 HD6417706 CPU.

config CPU_SUBTYPE_SH7707
	bool "Support SH7707 processor"
	select CPU_SH3
	select CPU_HAS_PINT_IRQ
	help
	  Select SH7707 if you have a  60 Mhz SH-3 HD6417707 CPU.

config CPU_SUBTYPE_SH7708
	bool "Support SH7708 processor"
	select CPU_SH3
	help
	  Select SH7708 if you have a  60 Mhz SH-3 HD6417708S or
	  if you have a 100 Mhz SH-3 HD6417708R CPU.

config CPU_SUBTYPE_SH7709
	bool "Support SH7709 processor"
	select CPU_SH3
	select CPU_HAS_IPR_IRQ
	select CPU_HAS_PINT_IRQ
	help
	  Select SH7709 if you have a  80 Mhz SH-3 HD6417709 CPU.

config CPU_SUBTYPE_SH7710
	bool "Support SH7710 processor"
	select CPU_SH3
	select CPU_HAS_IPR_IRQ
	help
	  Select SH7710 if you have a SH3-DSP SH7710 CPU.

config CPU_SUBTYPE_SH7712
	bool "Support SH7712 processor"
	select CPU_SH3
	select CPU_HAS_IPR_IRQ
	help
	  Select SH7712 if you have a SH3-DSP SH7712 CPU.

comment "SH-4 Processor Support"

config CPU_SUBTYPE_SH7750
	bool "Support SH7750 processor"
	select CPU_SH4
	select CPU_HAS_IPR_IRQ
	help
	  Select SH7750 if you have a 200 Mhz SH-4 HD6417750 CPU.

config CPU_SUBTYPE_SH7091
	bool "Support SH7091 processor"
	select CPU_SH4
	select CPU_SUBTYPE_SH7750
	help
	  Select SH7091 if you have an SH-4 based Sega device (such as
	  the Dreamcast, Naomi, and Naomi 2).

config CPU_SUBTYPE_SH7750R
	bool "Support SH7750R processor"
	select CPU_SH4
	select CPU_SUBTYPE_SH7750
	select CPU_HAS_IPR_IRQ

config CPU_SUBTYPE_SH7750S
	bool "Support SH7750S processor"
	select CPU_SH4
	select CPU_SUBTYPE_SH7750
	select CPU_HAS_IPR_IRQ

config CPU_SUBTYPE_SH7751
	bool "Support SH7751 processor"
	select CPU_SH4
	select CPU_HAS_IPR_IRQ
	help
	  Select SH7751 if you have a 166 Mhz SH-4 HD6417751 CPU,
	  or if you have a HD6417751R CPU.

config CPU_SUBTYPE_SH7751R
	bool "Support SH7751R processor"
	select CPU_SH4
	select CPU_SUBTYPE_SH7751
	select CPU_HAS_IPR_IRQ

config CPU_SUBTYPE_SH7760
	bool "Support SH7760 processor"
	select CPU_SH4
	select CPU_HAS_INTC2_IRQ
	select CPU_HAS_IPR_IRQ

config CPU_SUBTYPE_SH4_202
	bool "Support SH4-202 processor"
	select CPU_SH4

comment "ST40 Processor Support"

config CPU_SUBTYPE_ST40STB1
	bool "Support ST40STB1/ST40RA processors"
	select CPU_SUBTYPE_ST40
	help
	  Select ST40STB1 if you have a ST40RA CPU.
	  This was previously called the ST40STB1, hence the option name.

config CPU_SUBTYPE_ST40GX1
	bool "Support ST40GX1 processor"
	select CPU_SUBTYPE_ST40
	help
	  Select ST40GX1 if you have a ST40GX1 CPU.

comment "SH-4A Processor Support"

config CPU_SUBTYPE_SH7770
	bool "Support SH7770 processor"
	select CPU_SH4A

config CPU_SUBTYPE_SH7780
	bool "Support SH7780 processor"
	select CPU_SH4A
	select CPU_HAS_INTC2_IRQ

config CPU_SUBTYPE_SH7785
	bool "Support SH7785 processor"
	select CPU_SH4A
	select CPU_SHX2
	select CPU_HAS_INTC2_IRQ

comment "SH4AL-DSP Processor Support"

config CPU_SUBTYPE_SH73180
	bool "Support SH73180 processor"
	select CPU_SH4AL_DSP

config CPU_SUBTYPE_SH7343
	bool "Support SH7343 processor"
	select CPU_SH4AL_DSP

config CPU_SUBTYPE_SH7722
	bool "Support SH7722 processor"
	select CPU_SH4AL_DSP
	select CPU_SHX2
	select CPU_HAS_IPR_IRQ

endmenu

menu "Memory management options"

config MMU
        bool "Support for memory management hardware"
	depends on !CPU_SH2
	default y
	help
	  Some SH processors (such as SH-2/SH-2A) lack an MMU. In order to
	  boot on these systems, this option must not be set.

	  On other systems (such as the SH-3 and 4) where an MMU exists,
	  turning this off will boot the kernel on these machines with the
	  MMU implicitly switched off.

config PAGE_OFFSET
	hex
	default "0x80000000" if MMU
	default "0x00000000"

config MEMORY_START
	hex "Physical memory start address"
	default "0x08000000"
	---help---
	  Computers built with Hitachi SuperH processors always
	  map the ROM starting at address zero.  But the processor
	  does not specify the range that RAM takes.

	  The physical memory (RAM) start address will be automatically
	  set to 08000000. Other platforms, such as the Solution Engine
	  boards typically map RAM at 0C000000.

	  Tweak this only when porting to a new machine which does not
	  already have a defconfig. Changing it from the known correct
	  value on any of the known systems will only lead to disaster.

config MEMORY_SIZE
	hex "Physical memory size"
	default "0x00400000"
	help
	  This sets the default memory size assumed by your SH kernel. It can
	  be overridden as normal by the 'mem=' argument on the kernel command
	  line. If unsure, consult your board specifications or just leave it
	  as 0x00400000 which was the default value before this became
	  configurable.

config 32BIT
	bool "Support 32-bit physical addressing through PMB"
	depends on CPU_SH4A && MMU && (!X2TLB || BROKEN)
	default y
	help
	  If you say Y here, physical addressing will be extended to
	  32-bits through the SH-4A PMB. If this is not set, legacy
	  29-bit physical addressing will be used.

config X2TLB
	bool "Enable extended TLB mode"
	depends on CPU_SHX2 && MMU && EXPERIMENTAL
	help
	  Selecting this option will enable the extended mode of the SH-X2
	  TLB. For legacy SH-X behaviour and interoperability, say N. For
	  all of the fun new features and a willingless to submit bug reports,
	  say Y.

config VSYSCALL
	bool "Support vsyscall page"
	depends on MMU
	default y
	help
	  This will enable support for the kernel mapping a vDSO page
	  in process space, and subsequently handing down the entry point
	  to the libc through the ELF auxiliary vector.

	  From the kernel side this is used for the signal trampoline.
	  For systems with an MMU that can afford to give up a page,
	  (the default value) say Y.

config NODES_SHIFT
	int
	default "1"
	depends on NEED_MULTIPLE_NODES

config ARCH_FLATMEM_ENABLE
	def_bool y

config ARCH_POPULATES_NODE_MAP
	def_bool y

choice
	prompt "Kernel page size"
	default PAGE_SIZE_4KB

config PAGE_SIZE_4KB
	bool "4kB"
	help
	  This is the default page size used by all SuperH CPUs.

config PAGE_SIZE_8KB
	bool "8kB"
	depends on EXPERIMENTAL && X2TLB
	help
	  This enables 8kB pages as supported by SH-X2 and later MMUs.

config PAGE_SIZE_64KB
	bool "64kB"
	depends on EXPERIMENTAL && CPU_SH4
	help
	  This enables support for 64kB pages, possible on all SH-4
	  CPUs and later. Highly experimental, not recommended.

endchoice

choice
	prompt "HugeTLB page size"
	depends on HUGETLB_PAGE && CPU_SH4 && MMU
	default HUGETLB_PAGE_SIZE_64K

config HUGETLB_PAGE_SIZE_64K
	bool "64kB"

config HUGETLB_PAGE_SIZE_256K
	bool "256kB"
	depends on X2TLB

config HUGETLB_PAGE_SIZE_1MB
	bool "1MB"

config HUGETLB_PAGE_SIZE_4MB
	bool "4MB"
	depends on X2TLB

config HUGETLB_PAGE_SIZE_64MB
	bool "64MB"
	depends on X2TLB

endchoice

source "mm/Kconfig"

endmenu

menu "Cache configuration"

config SH7705_CACHE_32KB
	bool "Enable 32KB cache size for SH7705"
	depends on CPU_SUBTYPE_SH7705
	default y

config SH_DIRECT_MAPPED
	bool "Use direct-mapped caching"
	default n
	help
	  Selecting this option will configure the caches to be direct-mapped,
	  even if the cache supports a 2 or 4-way mode. This is useful primarily
	  for debugging on platforms with 2 and 4-way caches (SH7750R/SH7751R,
	  SH4-202, SH4-501, etc.)

	  Turn this option off for platforms that do not have a direct-mapped
	  cache, and you have no need to run the caches in such a configuration.

config SH_WRITETHROUGH
	bool "Use write-through caching"
	help
	  Selecting this option will configure the caches in write-through
	  mode, as opposed to the default write-back configuration.

	  Since there's sill some aliasing issues on SH-4, this option will
	  unfortunately still require the majority of flushing functions to
	  be implemented to deal with aliasing.

	  If unsure, say N.

config SH_OCRAM
	bool "Operand Cache RAM (OCRAM) support"
	help
	  Selecting this option will automatically tear down the number of
	  sets in the dcache by half, which in turn exposes a memory range.

	  The addresses for the OC RAM base will vary according to the
	  processor version. Consult vendor documentation for specifics.

	  If unsure, say N.

endmenu