drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h

/*
 * Copyright (c) 2010 Broadcom Corporation
 *
 * Permission to use, copy, modify, and/or distribute this software for any
 * purpose with or without fee is hereby granted, provided that the above
 * copyright notice and this permission notice appear in all copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
 * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
 * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
 * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 */

#ifndef	_BRCM_SDH_H_
#define	_BRCM_SDH_H_

#include <linux/skbuff.h>

#define SDIO_FUNC_0		0
#define SDIO_FUNC_1		1
#define SDIO_FUNC_2		2

#define SDIOD_FBR_SIZE		0x100

/* io_en */
#define SDIO_FUNC_ENABLE_1	0x02
#define SDIO_FUNC_ENABLE_2	0x04

/* io_rdys */
#define SDIO_FUNC_READY_1	0x02
#define SDIO_FUNC_READY_2	0x04

/* intr_status */
#define INTR_STATUS_FUNC1	0x2
#define INTR_STATUS_FUNC2	0x4

/* Maximum number of I/O funcs */
#define SDIOD_MAX_IOFUNCS	7

/* mask of register map */
#define REG_F0_REG_MASK		0x7FF
#define REG_F1_MISC_MASK	0x1FFFF

/* as of sdiod rev 0, supports 3 functions */
#define SBSDIO_NUM_FUNCTION		3

/* function 0 vendor specific CCCR registers */
#define SDIO_CCCR_BRCM_CARDCAP			0xf0
#define SDIO_CCCR_BRCM_CARDCAP_CMD14_SUPPORT	0x02
#define SDIO_CCCR_BRCM_CARDCAP_CMD14_EXT	0x04
#define SDIO_CCCR_BRCM_CARDCAP_CMD_NODEC	0x08
#define SDIO_CCCR_BRCM_CARDCTRL		0xf1
#define SDIO_CCCR_BRCM_CARDCTRL_WLANRESET	0x02
#define SDIO_CCCR_BRCM_SEPINT			0xf2

#define  SDIO_SEPINT_MASK		0x01
#define  SDIO_SEPINT_OE			0x02
#define  SDIO_SEPINT_ACT_HI		0x04

/* function 1 miscellaneous registers */

/* sprom command and status */
#define SBSDIO_SPROM_CS			0x10000
/* sprom info register */
#define SBSDIO_SPROM_INFO		0x10001
/* sprom indirect access data byte 0 */
#define SBSDIO_SPROM_DATA_LOW		0x10002
/* sprom indirect access data byte 1 */
#define SBSDIO_SPROM_DATA_HIGH		0x10003
/* sprom indirect access addr byte 0 */
#define SBSDIO_SPROM_ADDR_LOW		0x10004
/* sprom indirect access addr byte 0 */
#define SBSDIO_SPROM_ADDR_HIGH		0x10005
/* xtal_pu (gpio) output */
#define SBSDIO_CHIP_CTRL_DATA		0x10006
/* xtal_pu (gpio) enable */
#define SBSDIO_CHIP_CTRL_EN		0x10007
/* rev < 7, watermark for sdio device */
#define SBSDIO_WATERMARK		0x10008
/* control busy signal generation */
#define SBSDIO_DEVICE_CTL		0x10009

/* SB Address Window Low (b15) */
#define SBSDIO_FUNC1_SBADDRLOW		0x1000A
/* SB Address Window Mid (b23:b16) */
#define SBSDIO_FUNC1_SBADDRMID		0x1000B
/* SB Address Window High (b31:b24)    */
#define SBSDIO_FUNC1_SBADDRHIGH		0x1000C
/* Frame Control (frame term/abort) */
#define SBSDIO_FUNC1_FRAMECTRL		0x1000D
/* ChipClockCSR (ALP/HT ctl/status) */
#define SBSDIO_FUNC1_CHIPCLKCSR		0x1000E
/* SdioPullUp (on cmd, d0-d2) */
#define SBSDIO_FUNC1_SDIOPULLUP		0x1000F
/* Write Frame Byte Count Low */
#define SBSDIO_FUNC1_WFRAMEBCLO		0x10019
/* Write Frame Byte Count High */
#define SBSDIO_FUNC1_WFRAMEBCHI		0x1001A
/* Read Frame Byte Count Low */
#define SBSDIO_FUNC1_RFRAMEBCLO		0x1001B
/* Read Frame Byte Count High */
#define SBSDIO_FUNC1_RFRAMEBCHI		0x1001C
/* MesBusyCtl (rev 11) */
#define SBSDIO_FUNC1_MESBUSYCTRL	0x1001D
/* Sdio Core Rev 12 */
#define SBSDIO_FUNC1_WAKEUPCTRL		0x1001E
#define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK		0x1
#define SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT	0
#define SBSDIO_FUNC1_WCTRL_HTWAIT_MASK		0x2
#define SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT		1
#define SBSDIO_FUNC1_SLEEPCSR		0x1001F
#define SBSDIO_FUNC1_SLEEPCSR_KSO_MASK		0x1
#define SBSDIO_FUNC1_SLEEPCSR_KSO_SHIFT		0
#define SBSDIO_FUNC1_SLEEPCSR_KSO_EN		1
#define SBSDIO_FUNC1_SLEEPCSR_DEVON_MASK	0x2
#define SBSDIO_FUNC1_SLEEPCSR_DEVON_SHIFT	1

#define SBSDIO_FUNC1_MISC_REG_START	0x10000	/* f1 misc register start */
#define SBSDIO_FUNC1_MISC_REG_LIMIT	0x1001F	/* f1 misc register end */

/* function 1 OCP space */

/* sb offset addr is <= 15 bits, 32k */
#define SBSDIO_SB_OFT_ADDR_MASK		0x07FFF
#define SBSDIO_SB_OFT_ADDR_LIMIT	0x08000
/* with b15, maps to 32-bit SB access */
#define SBSDIO_SB_ACCESS_2_4B_FLAG	0x08000

/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */

#define SBSDIO_SBADDRLOW_MASK		0x80	/* Valid bits in SBADDRLOW */
#define SBSDIO_SBADDRMID_MASK		0xff	/* Valid bits in SBADDRMID */
#define SBSDIO_SBADDRHIGH_MASK		0xffU	/* Valid bits in SBADDRHIGH */
/* Address bits from SBADDR regs */
#define SBSDIO_SBWINDOW_MASK		0xffff8000

#define SDIOH_READ              0	/* Read request */
#define SDIOH_WRITE             1	/* Write request */

#define SDIOH_DATA_FIX          0	/* Fixed addressing */
#define SDIOH_DATA_INC          1	/* Incremental addressing */

/* internal return code */
#define SUCCESS	0
#define ERROR	1

/* Packet alignment for most efficient SDIO (can change based on platform) */
#define BRCMF_SDALIGN	(1 << 6)

/* watchdog polling interval in ms */
#define BRCMF_WD_POLL_MS	10

struct brcmf_sdreg {
	int func;
	int offset;
	int value;
};

struct brcmf_sdio;

struct brcmf_sdio_dev {
	struct sdio_func *func[SDIO_MAX_FUNCS];
	u8 num_funcs;			/* Supported funcs on client */
	u32 func_cis_ptr[SDIOD_MAX_IOFUNCS];
	u32 sbwad;			/* Save backplane window address */
	void *bus;
	atomic_t suspend;		/* suspend flag */
	wait_queue_head_t request_byte_wait;
	wait_queue_head_t request_word_wait;
	wait_queue_head_t request_buffer_wait;
	struct device *dev;
	struct brcmf_bus *bus_if;
	struct brcmfmac_sdio_platform_data *pdata;
	bool oob_irq_requested;
	bool irq_en;			/* irq enable flags */
	spinlock_t irq_en_lock;
	bool irq_wake;			/* irq wake enable flags */
};

/* Register/deregister interrupt handler. */
int brcmf_sdio_intr_register(struct brcmf_sdio_dev *sdiodev);
int brcmf_sdio_intr_unregister(struct brcmf_sdio_dev *sdiodev);

/* sdio device register access interface */
u8 brcmf_sdio_regrb(struct brcmf_sdio_dev *sdiodev, u32 addr, int *ret);
u32 brcmf_sdio_regrl(struct brcmf_sdio_dev *sdiodev, u32 addr, int *ret);
void brcmf_sdio_regwb(struct brcmf_sdio_dev *sdiodev, u32 addr, u8 data,
		      int *ret);
void brcmf_sdio_regwl(struct brcmf_sdio_dev *sdiodev, u32 addr, u32 data,
		      int *ret);
int brcmf_sdio_regrw_helper(struct brcmf_sdio_dev *sdiodev, u32 addr,
			    void *data, bool write);

/* Buffer transfer to/from device (client) core via cmd53.
 *   fn:       function number
 *   addr:     backplane address (i.e. >= regsva from attach)
 *   flags:    backplane width, address increment, sync/async
 *   buf:      pointer to memory data buffer
 *   nbytes:   number of bytes to transfer to/from buf
 *   pkt:      pointer to packet associated with buf (if any)
 *   complete: callback function for command completion (async only)
 *   handle:   handle for completion callback (first arg in callback)
 * Returns 0 or error code.
 * NOTE: Async operation is not currently supported.
 */
int brcmf_sdcard_send_pkt(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn,
			  uint flags, struct sk_buff_head *pktq);
int brcmf_sdcard_send_buf(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn,
			  uint flags, u8 *buf, uint nbytes);

int brcmf_sdcard_recv_pkt(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn,
			  uint flags, struct sk_buff *pkt);
int brcmf_sdcard_recv_buf(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn,
			  uint flags, u8 *buf, uint nbytes);
int brcmf_sdcard_recv_chain(struct brcmf_sdio_dev *sdiodev, u32 addr, uint fn,
			    uint flags, struct sk_buff_head *pktq);

/* Flags bits */

/* Four-byte target (backplane) width (vs. two-byte) */
#define SDIO_REQ_4BYTE	0x1
/* Fixed address (FIFO) (vs. incrementing address) */
#define SDIO_REQ_FIXED	0x2

/* Read/write to memory block (F1, no FIFO) via CMD53 (sync only).
 *   rw:       read or write (0/1)
 *   addr:     direct SDIO address
 *   buf:      pointer to memory data buffer
 *   nbytes:   number of bytes to transfer to/from buf
 * Returns 0 or error code.
 */
int brcmf_sdcard_rwdata(struct brcmf_sdio_dev *sdiodev, uint rw, u32 addr,
			u8 *buf, uint nbytes);
int brcmf_sdio_ramrw(struct brcmf_sdio_dev *sdiodev, bool write, u32 address,
		     u8 *data, uint size);

/* Issue an abort to the specified function */
int brcmf_sdcard_abort(struct brcmf_sdio_dev *sdiodev, uint fn);

/* platform specific/high level functions */
int brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev);
int brcmf_sdio_remove(struct brcmf_sdio_dev *sdiodev);

/* attach, return handler on success, NULL if failed.
 *  The handler shall be provided by all subsequent calls. No local cache
 *  cfghdl points to the starting address of pci device mapped memory
 */
int brcmf_sdioh_attach(struct brcmf_sdio_dev *sdiodev);
void brcmf_sdioh_detach(struct brcmf_sdio_dev *sdiodev);

/* read or write one byte using cmd52 */
int brcmf_sdioh_request_byte(struct brcmf_sdio_dev *sdiodev, uint rw, uint fnc,
			     uint addr, u8 *byte);

/* read or write 2/4 bytes using cmd53 */
int brcmf_sdioh_request_word(struct brcmf_sdio_dev *sdiodev, uint rw, uint fnc,
			     uint addr, u32 *word, uint nbyte);

/* Watchdog timer interface for pm ops */
void brcmf_sdio_wdtmr_enable(struct brcmf_sdio_dev *sdiodev, bool enable);

void *brcmf_sdbrcm_probe(u32 regsva, struct brcmf_sdio_dev *sdiodev);
void brcmf_sdbrcm_disconnect(void *ptr);
void brcmf_sdbrcm_isr(void *arg);

void brcmf_sdbrcm_wd_timer(struct brcmf_sdio *bus, uint wdtick);

void brcmf_pm_resume_wait(struct brcmf_sdio_dev *sdiodev,
			  wait_queue_head_t *wq);
bool brcmf_pm_resume_error(struct brcmf_sdio_dev *sdiodev);
#endif				/* _BRCM_SDH_H_ */