drivers/usb/serial/ftdi_sio.h

/*
 * Definitions for the FTDI USB Single Port Serial Converter - 
 * known as FTDI_SIO (Serial Input/Output application of the chipset) 
 *
 * The example I have is known as the USC-1000 which is available from
 * http://www.dse.co.nz - cat no XH4214 It looks similar to this:
 * http://www.dansdata.com/usbser.htm but I can't be sure There are other
 * USC-1000s which don't look like my device though so beware!
 *
 * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side, 
 * USB on the other.
 *
 * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
 * of the protocol required to talk to the device and ongoing assistence
 * during development.
 *
 * Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the 
 * FTDI_SIO implementation.
 *
 * Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
 * from Rudolf Gugler
 *
 */

#define FTDI_VID	0x0403	/* Vendor Id */
#define FTDI_SIO_PID	0x8372	/* Product Id SIO application of 8U100AX  */
#define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
#define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
#define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
#define FTDI_232RL_PID  0xFBFA  /* Product ID for FT232RL */
#define FTDI_RELAIS_PID	0xFA10  /* Relais device from Rudolf Gugler */
#define FTDI_NF_RIC_VID	0x0DCD	/* Vendor Id */
#define FTDI_NF_RIC_PID	0x0001	/* Product Id */
#define FTDI_USBX_707_PID 0xF857	/* ADSTech IR Blaster USBX-707 */


/* www.canusb.com Lawicel CANUSB device */
#define FTDI_CANUSB_PID 0xFFA8 /* Product Id */

/* AlphaMicro Components AMC-232USB01 device */
#define FTDI_AMC232_PID 0xFF00 /* Product Id */

/* ACT Solutions HomePro ZWave interface (http://www.act-solutions.com/HomePro.htm) */
#define FTDI_ACTZWAVE_PID	0xF2D0


/* www.starting-point-systems.com µChameleon device */
#define FTDI_MICRO_CHAMELEON_PID	0xCAA0	/* Product Id */

/* www.irtrans.de device */
#define FTDI_IRTRANS_PID 0xFC60 /* Product Id */


/* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
#define FTDI_TTUSB_PID 0xFF20 /* Product Id */

/* iPlus device */
#define FTDI_IPLUS_PID 0xD070 /* Product Id */
#define FTDI_IPLUS2_PID 0xD071 /* Product Id */

/* DMX4ALL DMX Interfaces */
#define FTDI_DMX4ALL 0xC850

/* OpenDCC (www.opendcc.de) product id */
#define FTDI_OPENDCC_PID	0xBFD8

/* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
/* they use the ftdi chipset for the USB interface and the vendor id is the same */
#define FTDI_XF_632_PID 0xFC08	/* 632: 16x2 Character Display */
#define FTDI_XF_634_PID 0xFC09	/* 634: 20x4 Character Display */
#define FTDI_XF_547_PID 0xFC0A	/* 547: Two line Display */
#define FTDI_XF_633_PID 0xFC0B	/* 633: 16x2 Character Display with Keys */
#define FTDI_XF_631_PID 0xFC0C	/* 631: 20x2 Character Display */
#define FTDI_XF_635_PID 0xFC0D	/* 635: 20x4 Character Display */
#define FTDI_XF_640_PID 0xFC0E	/* 640: Two line Display */
#define FTDI_XF_642_PID 0xFC0F	/* 642: Two line Display */

/* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
/* broadband internet service.  The following PID is exhibited by the usb device supplied */
/* (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */

/*
 * PCDJ use ftdi based dj-controllers.  The following PID is for their DAC-2 device
 * http://www.pcdjhardware.com/DAC2.asp (PID sent by Wouter Paesen)
 * (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_PCDJ_DAC2_PID 0xFA88

/*
 * The following are the values for the Matrix Orbital LCD displays,
 * which are the FT232BM ( similar to the 8U232AM )
 */
#define FTDI_MTXORB_0_PID      0xFA00  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_1_PID      0xFA01  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_2_PID      0xFA02  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_3_PID      0xFA03  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_4_PID      0xFA04  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_5_PID      0xFA05  /* Matrix Orbital Product Id */
#define FTDI_MTXORB_6_PID      0xFA06  /* Matrix Orbital Product Id */

/* Interbiometrics USB I/O Board */
/* Developed for Interbiometrics by Rudolf Gugler */
#define INTERBIOMETRICS_VID              0x1209
#define INTERBIOMETRICS_IOBOARD_PID      0x1002
#define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006

/*
 * The following are the values for the Perle Systems
 * UltraPort USB serial converters
 */
#define FTDI_PERLE_ULTRAPORT_PID 0xF0C0	/* Perle UltraPort Product Id */

/*
 * The following are the values for the Sealevel SeaLINK+ adapters.
 * (Original list sent by Tuan Hoang.  Ian Abbott renamed the macros and
 * removed some PIDs that don't seem to match any existing products.)
 */
#define SEALEVEL_VID		0x0c52	/* Sealevel Vendor ID */
#define SEALEVEL_2101_PID	0x2101	/* SeaLINK+232 (2101/2105) */
#define SEALEVEL_2102_PID	0x2102	/* SeaLINK+485 (2102) */
#define SEALEVEL_2103_PID	0x2103	/* SeaLINK+232I (2103) */
#define SEALEVEL_2104_PID	0x2104	/* SeaLINK+485I (2104) */
#define SEALEVEL_2106_PID	0x9020	/* SeaLINK+422 (2106) */
#define SEALEVEL_2201_1_PID	0x2211	/* SeaPORT+2/232 (2201) Port 1 */
#define SEALEVEL_2201_2_PID	0x2221	/* SeaPORT+2/232 (2201) Port 2 */
#define SEALEVEL_2202_1_PID	0x2212	/* SeaPORT+2/485 (2202) Port 1 */
#define SEALEVEL_2202_2_PID	0x2222	/* SeaPORT+2/485 (2202) Port 2 */
#define SEALEVEL_2203_1_PID	0x2213	/* SeaPORT+2 (2203) Port 1 */
#define SEALEVEL_2203_2_PID	0x2223	/* SeaPORT+2 (2203) Port 2 */
#define SEALEVEL_2401_1_PID	0x2411	/* SeaPORT+4/232 (2401) Port 1 */
#define SEALEVEL_2401_2_PID	0x2421	/* SeaPORT+4/232 (2401) Port 2 */
#define SEALEVEL_2401_3_PID	0x2431	/* SeaPORT+4/232 (2401) Port 3 */
#define SEALEVEL_2401_4_PID	0x2441	/* SeaPORT+4/232 (2401) Port 4 */
#define SEALEVEL_2402_1_PID	0x2412	/* SeaPORT+4/485 (2402) Port 1 */
#define SEALEVEL_2402_2_PID	0x2422	/* SeaPORT+4/485 (2402) Port 2 */
#define SEALEVEL_2402_3_PID	0x2432	/* SeaPORT+4/485 (2402) Port 3 */
#define SEALEVEL_2402_4_PID	0x2442	/* SeaPORT+4/485 (2402) Port 4 */
#define SEALEVEL_2403_1_PID	0x2413	/* SeaPORT+4 (2403) Port 1 */
#define SEALEVEL_2403_2_PID	0x2423	/* SeaPORT+4 (2403) Port 2 */
#define SEALEVEL_2403_3_PID	0x2433	/* SeaPORT+4 (2403) Port 3 */
#define SEALEVEL_2403_4_PID	0x2443	/* SeaPORT+4 (2403) Port 4 */
#define SEALEVEL_2801_1_PID	0X2811	/* SeaLINK+8/232 (2801) Port 1 */
#define SEALEVEL_2801_2_PID	0X2821	/* SeaLINK+8/232 (2801) Port 2 */
#define SEALEVEL_2801_3_PID	0X2831	/* SeaLINK+8/232 (2801) Port 3 */
#define SEALEVEL_2801_4_PID	0X2841	/* SeaLINK+8/232 (2801) Port 4 */
#define SEALEVEL_2801_5_PID	0X2851	/* SeaLINK+8/232 (2801) Port 5 */
#define SEALEVEL_2801_6_PID	0X2861	/* SeaLINK+8/232 (2801) Port 6 */
#define SEALEVEL_2801_7_PID	0X2871	/* SeaLINK+8/232 (2801) Port 7 */
#define SEALEVEL_2801_8_PID	0X2881	/* SeaLINK+8/232 (2801) Port 8 */
#define SEALEVEL_2802_1_PID	0X2812	/* SeaLINK+8/485 (2802) Port 1 */
#define SEALEVEL_2802_2_PID	0X2822	/* SeaLINK+8/485 (2802) Port 2 */
#define SEALEVEL_2802_3_PID	0X2832	/* SeaLINK+8/485 (2802) Port 3 */
#define SEALEVEL_2802_4_PID	0X2842	/* SeaLINK+8/485 (2802) Port 4 */
#define SEALEVEL_2802_5_PID	0X2852	/* SeaLINK+8/485 (2802) Port 5 */
#define SEALEVEL_2802_6_PID	0X2862	/* SeaLINK+8/485 (2802) Port 6 */
#define SEALEVEL_2802_7_PID	0X2872	/* SeaLINK+8/485 (2802) Port 7 */
#define SEALEVEL_2802_8_PID	0X2882	/* SeaLINK+8/485 (2802) Port 8 */
#define SEALEVEL_2803_1_PID	0X2813	/* SeaLINK+8 (2803) Port 1 */
#define SEALEVEL_2803_2_PID	0X2823 	/* SeaLINK+8 (2803) Port 2 */
#define SEALEVEL_2803_3_PID	0X2833 	/* SeaLINK+8 (2803) Port 3 */
#define SEALEVEL_2803_4_PID	0X2843 	/* SeaLINK+8 (2803) Port 4 */
#define SEALEVEL_2803_5_PID	0X2853 	/* SeaLINK+8 (2803) Port 5 */
#define SEALEVEL_2803_6_PID	0X2863 	/* SeaLINK+8 (2803) Port 6 */
#define SEALEVEL_2803_7_PID	0X2873 	/* SeaLINK+8 (2803) Port 7 */
#define SEALEVEL_2803_8_PID	0X2883 	/* SeaLINK+8 (2803) Port 8 */

/*
 * The following are the values for two KOBIL chipcard terminals.
 */
#define KOBIL_VID		0x0d46	/* KOBIL Vendor ID */
#define KOBIL_CONV_B1_PID	0x2020	/* KOBIL Konverter for B1 */
#define KOBIL_CONV_KAAN_PID	0x2021	/* KOBIL_Konverter for KAAN */

/*
 * Icom ID-1 digital transceiver
 */

#define ICOM_ID1_VID            0x0C26
#define ICOM_ID1_PID            0x0004

/*
 * ASK.fr devices
 */
#define FTDI_ASK_RDR400_PID	0xC991	/* ASK RDR 400 series card reader */

/*
 * FTDI USB UART chips used in construction projects from the
 * Elektor Electronics magazine (http://elektor-electronics.co.uk)
 */
#define ELEKTOR_VID		0x0C7D
#define ELEKTOR_FT323R_PID	0x0005	/* RFID-Reader, issue 09-2006 */

/*
 * DSS-20 Sync Station for Sony Ericsson P800
 */
#define FTDI_DSS20_PID          0xFC82  

/*
 * Home Electronics (www.home-electro.com) USB gadgets
 */
#define FTDI_HE_TIRA1_PID	0xFA78	/* Tira-1 IR transceiver */

/* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
/* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
#define FTDI_USB_UIRT_PID	0xF850	/* Product Id */

/* TNC-X USB-to-packet-radio adapter, versions prior to 3.0 (DLP module) */

#define FTDI_TNC_X_PID		0xEBE0

/*
 * ELV USB devices submitted by Christian Abt of ELV (www.elv.de).
 * All of these devices use FTDI's vendor ID (0x0403).
 *
 * The previously included PID for the UO 100 module was incorrect.
 * In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58).
 *
 * Armin Laeuger originally sent the PID for the UM 100 module.
 */
#define FTDI_ELV_UR100_PID	0xFB58	/* USB-RS232-Umsetzer (UR 100) */
#define FTDI_ELV_UM100_PID	0xFB5A	/* USB-Modul UM 100 */
#define FTDI_ELV_UO100_PID	0xFB5B	/* USB-Modul UO 100 */
#define FTDI_ELV_ALC8500_PID	0xF06E	/* ALC 8500 Expert */
/* Additional ELV PIDs that default to using the FTDI D2XX drivers on
 * MS Windows, rather than the FTDI Virtual Com Port drivers.
 * Maybe these will be easier to use with the libftdi/libusb user-space
 * drivers, or possibly the Comedi drivers in some cases. */
#define FTDI_ELV_CLI7000_PID	0xFB59	/* Computer-Light-Interface (CLI 7000) */
#define FTDI_ELV_PPS7330_PID	0xFB5C	/* Processor-Power-Supply (PPS 7330) */
#define FTDI_ELV_TFM100_PID	0xFB5D	/* Temperartur-Feuchte Messgeraet (TFM 100) */
#define FTDI_ELV_UDF77_PID	0xFB5E	/* USB DCF Funkurh (UDF 77) */
#define FTDI_ELV_UIO88_PID	0xFB5F	/* USB-I/O Interface (UIO 88) */
#define FTDI_ELV_UAD8_PID	0xF068	/* USB-AD-Wandler (UAD 8) */
#define FTDI_ELV_UDA7_PID	0xF069	/* USB-DA-Wandler (UDA 7) */
#define FTDI_ELV_USI2_PID	0xF06A	/* USB-Schrittmotoren-Interface (USI 2) */
#define FTDI_ELV_T1100_PID	0xF06B	/* Thermometer (T 1100) */
#define FTDI_ELV_PCD200_PID	0xF06C	/* PC-Datenlogger (PCD 200) */
#define FTDI_ELV_ULA200_PID	0xF06D	/* USB-LCD-Ansteuerung (ULA 200) */
#define FTDI_ELV_FHZ1000PC_PID	0xF06F	/* FHZ 1000 PC */
#define FTDI_ELV_CSI8_PID	0xE0F0	/* Computer-Schalt-Interface (CSI 8) */
#define FTDI_ELV_EM1000DL_PID	0xE0F1	/* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */
#define FTDI_ELV_PCK100_PID	0xE0F2	/* PC-Kabeltester (PCK 100) */
#define FTDI_ELV_RFP500_PID	0xE0F3	/* HF-Leistungsmesser (RFP 500) */
#define FTDI_ELV_FS20SIG_PID	0xE0F4	/* Signalgeber (FS 20 SIG) */
#define FTDI_ELV_WS300PC_PID	0xE0F6	/* PC-Wetterstation (WS 300 PC) */
#define FTDI_ELV_FHZ1300PC_PID	0xE0E8	/* FHZ 1300 PC */
#define FTDI_ELV_WS500_PID	0xE0E9	/* PC-Wetterstation (WS 500) */

/*
 * Definitions for ID TECH (www.idt-net.com) devices
 */
#define IDTECH_VID		0x0ACD	/* ID TECH Vendor ID */
#define IDTECH_IDT1221U_PID	0x0300	/* IDT1221U USB to RS-232 adapter */

/*
 * Definitions for Omnidirectional Control Technology, Inc. devices
 */
#define OCT_VID			0x0B39	/* OCT vendor ID */
/* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
/* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
/* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
#define OCT_US101_PID		0x0421	/* OCT US101 USB to RS-232 */

/* an infrared receiver for user access control with IR tags */
#define FTDI_PIEGROUP_PID	0xF208	/* Product Id */

/*
 * Definitions for Artemis astronomical USB based cameras
 * Check it at http://www.artemisccd.co.uk/
 */
#define FTDI_ARTEMIS_PID	0xDF28	/* All Artemis Cameras */

/*
 * Definitions for ATIK Instruments astronomical USB based cameras
 * Check it at http://www.atik-instruments.com/
 */
#define FTDI_ATIK_ATK16_PID	0xDF30	/* ATIK ATK-16 Grayscale Camera */
#define FTDI_ATIK_ATK16C_PID	0xDF32	/* ATIK ATK-16C Colour Camera */
#define FTDI_ATIK_ATK16HR_PID	0xDF31	/* ATIK ATK-16HR Grayscale Camera */
#define FTDI_ATIK_ATK16HRC_PID	0xDF33	/* ATIK ATK-16HRC Colour Camera */

/*
 * Protego product ids
 */
#define PROTEGO_SPECIAL_1	0xFC70	/* special/unknown device */
#define PROTEGO_R2X0		0xFC71	/* R200-USB TRNG unit (R210, R220, and R230) */
#define PROTEGO_SPECIAL_3	0xFC72	/* special/unknown device */
#define PROTEGO_SPECIAL_4	0xFC73	/* special/unknown device */

/*
 * Gude Analog- und Digitalsysteme GmbH
 */
#define FTDI_GUDEADS_E808_PID    0xE808
#define FTDI_GUDEADS_E809_PID    0xE809
#define FTDI_GUDEADS_E80A_PID    0xE80A
#define FTDI_GUDEADS_E80B_PID    0xE80B
#define FTDI_GUDEADS_E80C_PID    0xE80C
#define FTDI_GUDEADS_E80D_PID    0xE80D
#define FTDI_GUDEADS_E80E_PID    0xE80E
#define FTDI_GUDEADS_E80F_PID    0xE80F
#define FTDI_GUDEADS_E888_PID    0xE888  /* Expert ISDN Control USB */
#define FTDI_GUDEADS_E889_PID    0xE889  /* USB RS-232 OptoBridge */
#define FTDI_GUDEADS_E88A_PID    0xE88A
#define FTDI_GUDEADS_E88B_PID    0xE88B
#define FTDI_GUDEADS_E88C_PID    0xE88C
#define FTDI_GUDEADS_E88D_PID    0xE88D
#define FTDI_GUDEADS_E88E_PID    0xE88E
#define FTDI_GUDEADS_E88F_PID    0xE88F

/*
 * Linx Technologies product ids
 */
#define LINX_SDMUSBQSS_PID	0xF448	/* Linx SDM-USB-QS-S */
#define LINX_MASTERDEVEL2_PID   0xF449   /* Linx Master Development 2.0 */
#define LINX_FUTURE_0_PID   0xF44A   /* Linx future device */
#define LINX_FUTURE_1_PID   0xF44B   /* Linx future device */
#define LINX_FUTURE_2_PID   0xF44C   /* Linx future device */

/* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
/* unit for PIC16's/PIC18's */
#define FTDI_CCSICDU20_0_PID    0xF9D0
#define FTDI_CCSICDU40_1_PID    0xF9D1
#define FTDI_CCSMACHX_2_PID     0xF9D2

/* Inside Accesso contactless reader (http://www.insidefr.com) */
#define INSIDE_ACCESSO		0xFAD0

/*
 * Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
 */
#define INTREPID_VID		0x093C
#define INTREPID_VALUECAN_PID	0x0601
#define INTREPID_NEOVI_PID	0x0701

/*
 * Falcom Wireless Communications GmbH
 */
#define FALCOM_VID		0x0F94	/* Vendor Id */
#define FALCOM_TWIST_PID	0x0001	/* Falcom Twist USB GPRS modem */
#define FALCOM_SAMBA_PID	0x0005	/* Falcom Samba USB GPRS modem */

/*
 * SUUNTO product ids
 */
#define FTDI_SUUNTO_SPORTS_PID	0xF680	/* Suunto Sports instrument */

/*
 * TTi (Thurlby Thandar Instruments)
 */
#define TTI_VID			0x103E	/* Vendor Id */
#define TTI_QL355P_PID		0x03E8	/* TTi QL355P power supply */

/*
 * Definitions for B&B Electronics products.
 */
#define BANDB_VID		0x0856	/* B&B Electronics Vendor ID */
#define BANDB_USOTL4_PID	0xAC01	/* USOTL4 Isolated RS-485 Converter */
#define BANDB_USTL4_PID		0xAC02	/* USTL4 RS-485 Converter */
#define BANDB_USO9ML2_PID	0xAC03	/* USO9ML2 Isolated RS-232 Converter */

/*
 * RM Michaelides CANview USB (http://www.rmcan.com)
 * CAN fieldbus interface adapter, added by port GmbH www.port.de)
 * Ian Abbott changed the macro names for consistency.
 */
#define FTDI_RM_CANVIEW_PID	0xfd60	/* Product Id */

/*
 * EVER Eco Pro UPS (http://www.ever.com.pl/)
 */

#define	EVER_ECO_PRO_CDS	0xe520	/* RS-232 converter */

/*
 * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
 * USB-TTY activ, USB-TTY passiv.  Some PIDs are used by several devices
 * and I'm not entirely sure which are used by which.
 */
#define FTDI_4N_GALAXY_DE_1_PID	0xF3C0
#define FTDI_4N_GALAXY_DE_2_PID	0xF3C1

/*
 * Mobility Electronics products.
 */
#define MOBILITY_VID			0x1342
#define MOBILITY_USB_SERIAL_PID		0x0202	/* EasiDock USB 200 serial */

/*
 * microHAM product IDs (http://www.microham.com).
 * Submitted by Justin Burket (KL1RL) <zorton@jtan.com>
 * and Mike Studer (K6EEP) <k6eep@hamsoftware.org>.
 * Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file.
 */
#define FTDI_MHAM_KW_PID 0xEEE8		/* USB-KW interface */
#define FTDI_MHAM_YS_PID 0xEEE9		/* USB-YS interface */
#define FTDI_MHAM_Y6_PID 0xEEEA		/* USB-Y6 interface */
#define FTDI_MHAM_Y8_PID 0xEEEB		/* USB-Y8 interface */
#define FTDI_MHAM_IC_PID 0xEEEC		/* USB-IC interface */
#define FTDI_MHAM_DB9_PID 0xEEED	/* USB-DB9 interface */
#define FTDI_MHAM_RS232_PID 0xEEEE	/* USB-RS232 interface */
#define FTDI_MHAM_Y9_PID 0xEEEF		/* USB-Y9 interface */

/*
 * Active Robots product ids.
 */
#define FTDI_ACTIVE_ROBOTS_PID	0xE548	/* USB comms board */

/*
 * Xsens Technologies BV products (http://www.xsens.com).
 */
#define XSENS_CONVERTER_0_PID	0xD388
#define XSENS_CONVERTER_1_PID	0xD389
#define XSENS_CONVERTER_2_PID	0xD38A
#define XSENS_CONVERTER_3_PID	0xD38B
#define XSENS_CONVERTER_4_PID	0xD38C
#define XSENS_CONVERTER_5_PID	0xD38D
#define XSENS_CONVERTER_6_PID	0xD38E
#define XSENS_CONVERTER_7_PID	0xD38F

/*
 * Teratronik product ids.
 * Submitted by O. Wölfelschneider.
 */
#define FTDI_TERATRONIK_VCP_PID	 0xEC88	/* Teratronik device (preferring VCP driver on windows) */
#define FTDI_TERATRONIK_D2XX_PID 0xEC89	/* Teratronik device (preferring D2XX driver on windows) */

/*
 * Evolution Robotics products (http://www.evolution.com/).
 * Submitted by Shawn M. Lavelle.
 */
#define EVOLUTION_VID		0xDEEE	/* Vendor ID */
#define EVOLUTION_ER1_PID	0x0300	/* ER1 Control Module */
#define EVO_8U232AM_PID	0x02FF	/* Evolution robotics RCM2 (FT232AM)*/
#define EVO_HYBRID_PID		0x0302	/* Evolution robotics RCM4 PID (FT232BM)*/
#define EVO_RCM4_PID		0x0303	/* Evolution robotics RCM4 PID */

/* Pyramid Computer GmbH */
#define FTDI_PYRAMID_PID	0xE6C8	/* Pyramid Appliance Display */

/*
 * Posiflex inc retail equipment (http://www.posiflex.com.tw)
 */
#define POSIFLEX_VID		0x0d3a  /* Vendor ID */
#define POSIFLEX_PP7000_PID	0x0300  /* PP-7000II thermal printer */

/*
 * Westrex International devices submitted by Cory Lee
 */
#define FTDI_WESTREX_MODEL_777_PID	0xDC00	/* Model 777 */
#define FTDI_WESTREX_MODEL_8900F_PID	0xDC01	/* Model 8900F */

/*
 * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
 */
#define FTDI_RRCIRKITS_LOCOBUFFER_PID	0xc7d0	/* LocoBuffer USB */

/*
 * Eclo (http://www.eclo.pt/) product IDs.
 * PID 0xEA90 submitted by Martin Grill.
 */
#define FTDI_ECLO_COM_1WIRE_PID	0xEA90	/* COM to 1-Wire USB adaptor */

/*
 * Papouch products (http://www.papouch.com/)
 * Submitted by Folkert van Heusden
 */

#define PAPOUCH_VID			0x5050	/* Vendor ID */
#define PAPOUCH_TMU_PID			0x0400	/* TMU USB Thermometer */

/*
 * ACG Identification Technologies GmbH products (http://www.acg.de/).
 * Submitted by anton -at- goto10 -dot- org.
 */
#define FTDI_ACG_HFDUAL_PID		0xDD20	/* HF Dual ISO Reader (RFID) */

/*
 * Yost Engineering, Inc. products (www.yostengineering.com).
 * PID 0xE050 submitted by Aaron Prose.
 */
#define FTDI_YEI_SERVOCENTER31_PID	0xE050	/* YEI ServoCenter3.1 USB */

/*
 * ThorLabs USB motor drivers
 */
#define FTDI_THORLABS_PID		0xfaf0 /* ThorLabs USB motor drivers */

/*
 * Testo products (http://www.testo.com/)
 * Submitted by Colin Leroy
 */
#define TESTO_VID			0x128D
#define TESTO_USB_INTERFACE_PID		0x0001

/*
 * Gamma Scout (http://gamma-scout.com/). Submitted by rsc@runtux.com.
 */
#define FTDI_GAMMA_SCOUT_PID		0xD678	/* Gamma Scout online */

/*
 * Tactrix OpenPort (ECU) devices.
 * OpenPort 1.3M submitted by Donour Sizemore.
 * OpenPort 1.3S and 1.3U submitted by Ian Abbott.
 */
#define FTDI_TACTRIX_OPENPORT_13M_PID	0xCC48	/* OpenPort 1.3 Mitsubishi */
#define FTDI_TACTRIX_OPENPORT_13S_PID	0xCC49	/* OpenPort 1.3 Subaru */
#define FTDI_TACTRIX_OPENPORT_13U_PID	0xCC4A	/* OpenPort 1.3 Universal */

/*
 * Telldus Technologies
 */
#define TELLDUS_VID			0x1781	/* Vendor ID */
#define TELLDUS_TELLSTICK_PID		0x0C30	/* RF control dongle 433 MHz using FT232RL */

/*
 * IBS elektronik product ids
 * Submitted by Thomas Schleusener
 */
#define FTDI_IBS_US485_PID	0xff38  /* IBS US485 (USB<-->RS422/485 interface) */
#define FTDI_IBS_PICPRO_PID	0xff39  /* IBS PIC-Programmer */
#define FTDI_IBS_PCMCIA_PID	0xff3a  /* IBS Card reader for PCMCIA SRAM-cards */
#define FTDI_IBS_PK1_PID	0xff3b  /* IBS PK1 - Particel counter */
#define FTDI_IBS_RS232MON_PID	0xff3c  /* IBS RS232 - Monitor */
#define FTDI_IBS_APP70_PID	0xff3d  /* APP 70 (dust monitoring system) */
#define FTDI_IBS_PEDO_PID	0xff3e  /* IBS PEDO-Modem (RF modem 868.35 MHz) */
#define FTDI_IBS_PROD_PID	0xff3f  /* future device */

/*
 *  MaxStream devices	www.maxstream.net
 */
#define FTDI_MAXSTREAM_PID	0xEE18	/* Xbee PKG-U Module */

/* Olimex */
#define OLIMEX_VID			0x15BA
#define OLIMEX_ARM_USB_OCD_PID		0x0003

/* Commands */
#define FTDI_SIO_RESET 		0 /* Reset the port */
#define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */
#define FTDI_SIO_SET_FLOW_CTRL	2 /* Set flow control register */
#define FTDI_SIO_SET_BAUD_RATE	3 /* Set baud rate */
#define FTDI_SIO_SET_DATA	4 /* Set the data characteristics of the port */
#define FTDI_SIO_GET_MODEM_STATUS	5 /* Retrieve current value of modern status register */
#define FTDI_SIO_SET_EVENT_CHAR	6 /* Set the event character */
#define FTDI_SIO_SET_ERROR_CHAR	7 /* Set the error character */
#define FTDI_SIO_SET_LATENCY_TIMER	9 /* Set the latency timer */
#define FTDI_SIO_GET_LATENCY_TIMER	10 /* Get the latency timer */


/*
 *   BmRequestType:  1100 0000b
 *   bRequest:       FTDI_E2_READ
 *   wValue:         0
 *   wIndex:         Address of word to read
 *   wLength:        2
 *   Data:           Will return a word of data from E2Address
 *
 */

/* Port Identifier Table */
#define PIT_DEFAULT 		0 /* SIOA */
#define PIT_SIOA		1 /* SIOA */
/* The device this driver is tested with one has only one port */
#define PIT_SIOB		2 /* SIOB */
#define PIT_PARALLEL		3 /* Parallel */

/* FTDI_SIO_RESET */
#define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
#define FTDI_SIO_RESET_REQUEST_TYPE 0x40
#define FTDI_SIO_RESET_SIO 0
#define FTDI_SIO_RESET_PURGE_RX 1
#define FTDI_SIO_RESET_PURGE_TX 2

/*
 * BmRequestType:  0100 0000B
 * bRequest:       FTDI_SIO_RESET
 * wValue:         Control Value 
 *                   0 = Reset SIO
 *                   1 = Purge RX buffer
 *                   2 = Purge TX buffer
 * wIndex:         Port
 * wLength:        0
 * Data:           None
 *
 * The Reset SIO command has this effect:
 *
 *    Sets flow control set to 'none'
 *    Event char = $0D
 *    Event trigger = disabled
 *    Purge RX buffer
 *    Purge TX buffer
 *    Clear DTR
 *    Clear RTS
 *    baud and data format not reset
 *
 * The Purge RX and TX buffer commands affect nothing except the buffers
 *
   */

/* FTDI_SIO_SET_BAUDRATE */
#define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_BAUDRATE_REQUEST 3

/*
 * BmRequestType:  0100 0000B
 * bRequest:       FTDI_SIO_SET_BAUDRATE
 * wValue:         BaudDivisor value - see below
 * wIndex:         Port
 * wLength:        0
 * Data:           None
 * The BaudDivisor values are calculated as follows:
 * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
 *   I knew how to detect old chips to select proper base clock!
 * - BaudDivisor is a fixed point number encoded in a funny way.
 *   (--WRONG WAY OF THINKING--)
 *   BaudDivisor is a fixed point number encoded with following bit weighs:
 *   (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
 *   end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
 *   (--THE REALITY--)
 *   The both-bits-set has quite different meaning from 0.75 - the chip designers
 *   have decided it to mean 0.125 instead of 0.75.
 *   This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
 *   and Flow Control Consideration for USB to RS232".
 * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
 *   automagically re-encode the resulting value to take fractions into consideration.
 * As all values are integers, some bit twiddling is in order:
 *   BaudDivisor = (BaseClock / 16 / BaudRate) |
 *   (((BaseClock / 2 / BaudRate) & 4) ? 0x4000    // 0.5
 *    : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000  // 0.25
 *    : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000  // 0.125
 *    : 0)
 *
 * For the FT232BM, a 17th divisor bit was introduced to encode the multiples
 * of 0.125 missing from the FT8U232AM.  Bits 16 to 14 are coded as follows
 * (the first four codes are the same as for the FT8U232AM, where bit 16 is
 * always 0):
 *   000 - add .000 to divisor
 *   001 - add .500 to divisor
 *   010 - add .250 to divisor
 *   011 - add .125 to divisor
 *   100 - add .375 to divisor
 *   101 - add .625 to divisor
 *   110 - add .750 to divisor
 *   111 - add .875 to divisor
 * Bits 15 to 0 of the 17-bit divisor are placed in the urb value.  Bit 16 is 
 * placed in bit 0 of the urb index.
 *
 * Note that there are a couple of special cases to support the highest baud
 * rates.  If the calculated divisor value is 1, this needs to be replaced with
 * 0.  Additionally for the FT232BM, if the calculated divisor value is 0x4001
 * (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
 * not supported by the FT8U232AM).
 */

typedef enum {
	SIO = 1,
	FT8U232AM = 2,
	FT232BM = 3,
	FT2232C = 4,
	FT232RL = 5,
} ftdi_chip_type_t;

typedef enum {
 ftdi_sio_b300 = 0, 
 ftdi_sio_b600 = 1, 
 ftdi_sio_b1200 = 2,
 ftdi_sio_b2400 = 3,
 ftdi_sio_b4800 = 4,
 ftdi_sio_b9600 = 5,
 ftdi_sio_b19200 = 6,
 ftdi_sio_b38400 = 7,
 ftdi_sio_b57600 = 8,
 ftdi_sio_b115200 = 9
} FTDI_SIO_baudrate_t ;

/*
 * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
 * are calculated internally.
 */

#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )
#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )
#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )
#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )
#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )
#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )
#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )
#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )
#define FTDI_SIO_SET_BREAK (0x1 << 14)
/* FTDI_SIO_SET_DATA */

/*
 * BmRequestType:  0100 0000B 
 * bRequest:       FTDI_SIO_SET_DATA
 * wValue:         Data characteristics (see below)
 * wIndex:         Port
 * wLength:        0
 * Data:           No
 *
 * Data characteristics
 *
 *   B0..7   Number of data bits
 *   B8..10  Parity
 *           0 = None
 *           1 = Odd
 *           2 = Even
 *           3 = Mark
 *           4 = Space
 *   B11..13 Stop Bits
 *           0 = 1
 *           1 = 1.5
 *           2 = 2
 *   B14
 *           1 = TX ON (break)
 *           0 = TX OFF (normal state)
 *   B15 Reserved
 *
 */



/* FTDI_SIO_MODEM_CTRL */
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL

/* 
 * BmRequestType:   0100 0000B
 * bRequest:        FTDI_SIO_MODEM_CTRL
 * wValue:          ControlValue (see below)
 * wIndex:          Port
 * wLength:         0
 * Data:            None
 *
 * NOTE: If the device is in RTS/CTS flow control, the RTS set by this
 * command will be IGNORED without an error being returned
 * Also - you can not set DTR and RTS with one control message
 */

#define FTDI_SIO_SET_DTR_MASK 0x1
#define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
#define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
#define FTDI_SIO_SET_RTS_MASK 0x2
#define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
#define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))

/*
 * ControlValue
 * B0    DTR state
 *          0 = reset
 *          1 = set
 * B1    RTS state
 *          0 = reset
 *          1 = set
 * B2..7 Reserved
 * B8    DTR state enable
 *          0 = ignore
 *          1 = use DTR state
 * B9    RTS state enable
 *          0 = ignore
 *          1 = use RTS state
 * B10..15 Reserved
 */

/* FTDI_SIO_SET_FLOW_CTRL */
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
#define FTDI_SIO_DISABLE_FLOW_CTRL 0x0 
#define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
#define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
#define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
/*
 *   BmRequestType:  0100 0000b
 *   bRequest:       FTDI_SIO_SET_FLOW_CTRL
 *   wValue:         Xoff/Xon
 *   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port
 *   wLength:        0 
 *   Data:           None
 *
 * hIndex protocol is:
 *   B0 Output handshaking using RTS/CTS
 *       0 = disabled
 *       1 = enabled
 *   B1 Output handshaking using DTR/DSR
 *       0 = disabled
 *       1 = enabled
 *   B2 Xon/Xoff handshaking
 *       0 = disabled
 *       1 = enabled
 *
 * A value of zero in the hIndex field disables handshaking
 *
 * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character 
 * and the lValue field contains the XON character.
 */  
 
/*
 * FTDI_SIO_GET_LATENCY_TIMER
 *
 * Set the timeout interval. The FTDI collects data from the slave
 * device, transmitting it to the host when either A) 62 bytes are
 * received, or B) the timeout interval has elapsed and the buffer
 * contains at least 1 byte.  Setting this value to a small number
 * can dramatically improve performance for applications which send
 * small packets, since the default value is 16ms.
 */
#define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
#define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0

/* 
 *  BmRequestType:   1100 0000b
 *  bRequest:        FTDI_SIO_GET_LATENCY_TIMER
 *  wValue:          0
 *  wIndex:          Port
 *  wLength:         0
 *  Data:            latency (on return)
 */

/* 
 * FTDI_SIO_SET_LATENCY_TIMER
 *
 * Set the timeout interval. The FTDI collects data from the slave
 * device, transmitting it to the host when either A) 62 bytes are
 * received, or B) the timeout interval has elapsed and the buffer
 * contains at least 1 byte.  Setting this value to a small number
 * can dramatically improve performance for applications which send
 * small packets, since the default value is 16ms.
 */
#define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
#define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40

/* 
 *  BmRequestType:   0100 0000b
 *  bRequest:        FTDI_SIO_SET_LATENCY_TIMER
 *  wValue:          Latency (milliseconds)
 *  wIndex:          Port
 *  wLength:         0
 *  Data:            None
 *
 * wValue:
 *   B0..7   Latency timer
 *   B8..15  0
 *
 */

/*
 * FTDI_SIO_SET_EVENT_CHAR 
 *
 * Set the special event character for the specified communications port.
 * If the device sees this character it will immediately return the
 * data read so far - rather than wait 40ms or until 62 bytes are read
 * which is what normally happens.
 */


#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40


/* 
 *  BmRequestType:   0100 0000b
 *  bRequest:        FTDI_SIO_SET_EVENT_CHAR
 *  wValue:          EventChar
 *  wIndex:          Port
 *  wLength:         0
 *  Data:            None
 *
 * wValue:
 *   B0..7   Event Character
 *   B8      Event Character Processing
 *             0 = disabled
 *             1 = enabled
 *   B9..15  Reserved
 *
 */
          
/* FTDI_SIO_SET_ERROR_CHAR */

/* Set the parity error replacement character for the specified communications port */

/* 
 *  BmRequestType:  0100 0000b
 *  bRequest:       FTDI_SIO_SET_EVENT_CHAR
 *  wValue:         Error Char
 *  wIndex:         Port
 *  wLength:        0
 *  Data:           None
 *
 *Error Char
 *  B0..7  Error Character
 *  B8     Error Character Processing
 *           0 = disabled
 *           1 = enabled
 *  B9..15 Reserved
 *
 */

/* FTDI_SIO_GET_MODEM_STATUS */
/* Retrieve the current value of the modem status register */

#define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
#define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
#define FTDI_SIO_CTS_MASK 0x10
#define FTDI_SIO_DSR_MASK 0x20
#define FTDI_SIO_RI_MASK  0x40
#define FTDI_SIO_RLSD_MASK 0x80
/* 
 *   BmRequestType:   1100 0000b
 *   bRequest:        FTDI_SIO_GET_MODEM_STATUS
 *   wValue:          zero
 *   wIndex:          Port
 *   wLength:         1
 *   Data:            Status
 * 
 * One byte of data is returned 
 * B0..3 0
 * B4    CTS
 *         0 = inactive
 *         1 = active
 * B5    DSR
 *         0 = inactive
 *         1 = active
 * B6    Ring Indicator (RI)
 *         0 = inactive
 *         1 = active
 * B7    Receive Line Signal Detect (RLSD)
 *         0 = inactive
 *         1 = active 
 */



/* Descriptors returned by the device 
 * 
 *  Device Descriptor
 * 
 * Offset	Field		Size	Value	Description
 * 0	bLength		1	0x12	Size of descriptor in bytes
 * 1	bDescriptorType	1	0x01	DEVICE Descriptor Type
 * 2	bcdUSB		2	0x0110	USB Spec Release Number
 * 4	bDeviceClass	1	0x00	Class Code
 * 5	bDeviceSubClass	1	0x00	SubClass Code
 * 6	bDeviceProtocol	1	0x00	Protocol Code
 * 7	bMaxPacketSize0 1	0x08	Maximum packet size for endpoint 0
 * 8	idVendor	2	0x0403	Vendor ID
 * 10	idProduct	2	0x8372	Product ID (FTDI_SIO_PID)
 * 12	bcdDevice	2	0x0001	Device release number
 * 14	iManufacturer	1	0x01	Index of man. string desc
 * 15	iProduct	1	0x02	Index of prod string desc
 * 16	iSerialNumber	1	0x02	Index of serial nmr string desc
 * 17	bNumConfigurations 1    0x01	Number of possible configurations
 * 
 * Configuration Descriptor
 * 
 * Offset	Field			Size	Value
 * 0	bLength			1	0x09	Size of descriptor in bytes
 * 1	bDescriptorType		1	0x02	CONFIGURATION Descriptor Type
 * 2	wTotalLength		2	0x0020	Total length of data
 * 4	bNumInterfaces		1	0x01	Number of interfaces supported
 * 5	bConfigurationValue	1	0x01	Argument for SetCOnfiguration() req
 * 6	iConfiguration		1	0x02	Index of config string descriptor
 * 7	bmAttributes		1	0x20	Config characteristics Remote Wakeup
 * 8	MaxPower		1	0x1E	Max power consumption
 * 
 * Interface Descriptor
 * 
 * Offset	Field			Size	Value
 * 0	bLength			1	0x09	Size of descriptor in bytes
 * 1	bDescriptorType		1	0x04	INTERFACE Descriptor Type
 * 2	bInterfaceNumber	1	0x00	Number of interface
 * 3	bAlternateSetting	1	0x00	Value used to select alternate
 * 4	bNumEndpoints		1	0x02	Number of endpoints
 * 5	bInterfaceClass		1	0xFF	Class Code
 * 6	bInterfaceSubClass	1	0xFF	Subclass Code
 * 7	bInterfaceProtocol	1	0xFF	Protocol Code
 * 8	iInterface		1	0x02	Index of interface string description
 * 
 * IN Endpoint Descriptor
 * 
 * Offset	Field			Size	Value
 * 0	bLength			1	0x07	Size of descriptor in bytes
 * 1	bDescriptorType		1	0x05	ENDPOINT descriptor type
 * 2	bEndpointAddress	1	0x82	Address of endpoint
 * 3	bmAttributes		1	0x02	Endpoint attributes - Bulk
 * 4	bNumEndpoints		2	0x0040	maximum packet size
 * 5	bInterval		1	0x00	Interval for polling endpoint
 * 
 * OUT Endpoint Descriptor
 * 
 * Offset	Field			Size	Value
 * 0	bLength			1	0x07	Size of descriptor in bytes
 * 1	bDescriptorType		1	0x05	ENDPOINT descriptor type
 * 2	bEndpointAddress	1	0x02	Address of endpoint
 * 3	bmAttributes		1	0x02	Endpoint attributes - Bulk
 * 4	bNumEndpoints		2	0x0040	maximum packet size
 * 5	bInterval		1	0x00	Interval for polling endpoint
 *     
 * DATA FORMAT
 * 
 * IN Endpoint
 * 
 * The device reserves the first two bytes of data on this endpoint to contain the current
 * values of the modem and line status registers. In the absence of data, the device 
 * generates a message consisting of these two status bytes every 40 ms
 * 
 * Byte 0: Modem Status
 * 
 * Offset	Description
 * B0	Reserved - must be 1
 * B1	Reserved - must be 0
 * B2	Reserved - must be 0
 * B3	Reserved - must be 0
 * B4	Clear to Send (CTS)
 * B5	Data Set Ready (DSR)
 * B6	Ring Indicator (RI)
 * B7	Receive Line Signal Detect (RLSD)
 * 
 * Byte 1: Line Status
 * 
 * Offset	Description
 * B0	Data Ready (DR)
 * B1	Overrun Error (OE)
 * B2	Parity Error (PE)
 * B3	Framing Error (FE)
 * B4	Break Interrupt (BI)
 * B5	Transmitter Holding Register (THRE)
 * B6	Transmitter Empty (TEMT)
 * B7	Error in RCVR FIFO
 * 
 */
#define FTDI_RS0_CTS	(1 << 4)
#define FTDI_RS0_DSR	(1 << 5)
#define FTDI_RS0_RI	(1 << 6)
#define FTDI_RS0_RLSD	(1 << 7)

#define FTDI_RS_DR  1
#define FTDI_RS_OE (1<<1)
#define FTDI_RS_PE (1<<2)
#define FTDI_RS_FE (1<<3)
#define FTDI_RS_BI (1<<4)
#define FTDI_RS_THRE (1<<5)
#define FTDI_RS_TEMT (1<<6)
#define FTDI_RS_FIFO  (1<<7)

/*
 * OUT Endpoint
 * 
 * This device reserves the first bytes of data on this endpoint contain the length
 * and port identifier of the message. For the FTDI USB Serial converter the port 
 * identifier is always 1.
 * 
 * Byte 0: Line Status
 * 
 * Offset	Description
 * B0	Reserved - must be 1
 * B1	Reserved - must be 0
 * B2..7	Length of message - (not including Byte 0)
 * 
 */