iwlwifi: add iwl5000_tx_response structure
This patch adds iwl5000_tx_repsons structure.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h
index 6f62beb..bad0e94 100644
--- a/drivers/net/wireless/iwlwifi/iwl-commands.h
+++ b/drivers/net/wireless/iwlwifi/iwl-commands.h
@@ -1419,6 +1419,11 @@
* within the sending station (this 4965), rather than whether it was
* received successfully by the destination station.
*/
+struct agg_tx_status {
+ __le16 status;
+ __le16 sequence;
+} __attribute__ ((packed));
+
struct iwl4965_tx_resp {
u8 frame_count; /* 1 no aggregation, >1 aggregation */
u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
@@ -1453,11 +1458,6 @@
__le32 status; /* TX status (for aggregation status of 1st frame) */
} __attribute__ ((packed));
-struct agg_tx_status {
- __le16 status;
- __le16 sequence;
-} __attribute__ ((packed));
-
struct iwl4965_tx_resp_agg {
u8 frame_count; /* 1 no aggregation, >1 aggregation */
u8 reserved1;
@@ -1472,6 +1472,44 @@
/* of 1st frame) */
} __attribute__ ((packed));
+struct iwl5000_tx_resp {
+ u8 frame_count; /* 1 no aggregation, >1 aggregation */
+ u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
+ u8 failure_rts; /* # failures due to unsuccessful RTS */
+ u8 failure_frame; /* # failures due to no ACK (unused for agg) */
+
+ /* For non-agg: Rate at which frame was successful.
+ * For agg: Rate at which all frames were transmitted. */
+ __le32 rate_n_flags; /* RATE_MCS_* */
+
+ /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
+ * For agg: RTS + CTS + aggregation tx time + block-ack time. */
+ __le16 wireless_media_time; /* uSecs */
+
+ __le16 reserved;
+ __le32 pa_power1; /* RF power amplifier measurement (not used) */
+ __le32 pa_power2;
+
+ __le32 tfd_info;
+ __le16 seq_ctl;
+ __le16 byte_cnt;
+ __le32 tlc_info;
+ /*
+ * For non-agg: frame status TX_STATUS_*
+ * For agg: status of 1st frame, AGG_TX_STATE_*; other frame status
+ * fields follow this one, up to frame_count.
+ * Bit fields:
+ * 11- 0: AGG_TX_STATE_* status code
+ * 15-12: Retry count for 1st frame in aggregation (retries
+ * occur if tx failed for this frame when it was a
+ * member of a previous aggregation block). If rate
+ * scaling is used, retry count indicates the rate
+ * table entry used for all frames in the new agg.
+ * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
+ */
+ struct agg_tx_status status; /* TX status (in aggregation -
+ * status of 1st frame) */
+} __attribute__ ((packed));
/*
* REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
*