[netdrvr] Remove Linux-specific changelogs from several Becker template drivers
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code. These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.
Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9". These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.
Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sundance.c b/drivers/net/sundance.c
index 643fcea..de66451 100644
--- a/drivers/net/sundance.c
+++ b/drivers/net/sundance.c
@@ -16,91 +16,13 @@
Support and updates available at
http://www.scyld.com/network/sundance.html
+ [link no longer provides useful info -jgarzik]
-
- Version LK1.01a (jgarzik):
- - Replace some MII-related magic numbers with constants
-
- Version LK1.02 (D-Link):
- - Add new board to PCI ID list
- - Fix multicast bug
-
- Version LK1.03 (D-Link):
- - New Rx scheme, reduce Rx congestion
- - Option to disable flow control
-
- Version LK1.04 (D-Link):
- - Tx timeout recovery
- - More support for ethtool.
-
- Version LK1.04a:
- - Remove unused/constant members from struct pci_id_info
- (which then allows removal of 'drv_flags' from private struct)
- (jgarzik)
- - If no phy is found, fail to load that board (jgarzik)
- - Always start phy id scan at id 1 to avoid problems (Donald Becker)
- - Autodetect where mii_preable_required is needed,
- default to not needed. (Donald Becker)
-
- Version LK1.04b:
- - Remove mii_preamble_required module parameter (Donald Becker)
- - Add per-interface mii_preamble_required (setting is autodetected)
- (Donald Becker)
- - Remove unnecessary cast from void pointer (jgarzik)
- - Re-align comments in private struct (jgarzik)
-
- Version LK1.04c (jgarzik):
- - Support bitmapped message levels (NETIF_MSG_xxx), and the
- two ethtool ioctls that get/set them
- - Don't hand-code MII ethtool support, use standard API/lib
-
- Version LK1.04d:
- - Merge from Donald Becker's sundance.c: (Jason Lunz)
- * proper support for variably-sized MTUs
- * default to PIO, to fix chip bugs
- - Add missing unregister_netdev (Jason Lunz)
- - Add CONFIG_SUNDANCE_MMIO config option (jgarzik)
- - Better rx buf size calculation (Donald Becker)
-
- Version LK1.05 (D-Link):
- - Fix DFE-580TX packet drop issue (for DL10050C)
- - Fix reset_tx logic
-
- Version LK1.06 (D-Link):
- - Fix crash while unloading driver
-
- Versin LK1.06b (D-Link):
- - New tx scheme, adaptive tx_coalesce
-
- Version LK1.07 (D-Link):
- - Fix tx bugs in big-endian machines
- - Remove unused max_interrupt_work module parameter, the new
- NAPI-like rx scheme doesn't need it.
- - Remove redundancy get_stats() in intr_handler(), those
- I/O access could affect performance in ARM-based system
- - Add Linux software VLAN support
-
- Version LK1.08 (Philippe De Muyter phdm@macqel.be):
- - Fix bug of custom mac address
- (StationAddr register only accept word write)
-
- Version LK1.09 (D-Link):
- - Fix the flowctrl bug.
- - Set Pause bit in MII ANAR if flow control enabled.
-
- Version LK1.09a (ICPlus):
- - Add the delay time in reading the contents of EEPROM
-
- Version LK1.10 (Philippe De Muyter phdm@macqel.be):
- - Make 'unblock interface after Tx underrun' work
-
- Version LK1.11 (Pedro Alejandro Lopez-Valencia palopezv at gmail.com):
- - Add support for IC Plus Corporation IP100A chipset
*/
#define DRV_NAME "sundance"
-#define DRV_VERSION "1.01+LK1.11"
-#define DRV_RELDATE "14-Jun-2006"
+#define DRV_VERSION "1.1"
+#define DRV_RELDATE "27-Jun-2006"
/* The user-configurable values.