Merge branches 'arnd-randcfg-fixes', 'debug', 'io' (early part), 'l2x0', 'p2v', 'pgt' (early part) and 'smp' into for-linus
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
new file mode 100644
index 0000000..7ca5216
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+ "arm,pl310-cache"
+ "arm,l220-cache"
+ "arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+ registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Minimum valid values are 1. Controllers
+ without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+ read, write and setup latencies. Controllers without setup latency control
+ should use 0. Controllers without separate read and write Tag RAM latency
+ values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+ filter. Addresses in the filter window are directed to the M1 port. Other
+ addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+ compatible = "arm,pl310-cache";
+ reg = <0xfff12000 0x1000>;
+ arm,data-latency = <1 1 1>;
+ arm,tag-latency = <2 2 2>;
+ arm,filter-latency = <0x80000000 0x8000000>;
+ cache-unified;
+ cache-level = <2>;
+ interrupts = <45>;
+};
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3146ed3..380e4f0 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -3,7 +3,7 @@
default y
select HAVE_AOUT
select HAVE_DMA_API_DEBUG
- select HAVE_IDE
+ select HAVE_IDE if PCI || ISA || PCMCIA
select HAVE_MEMBLOCK
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
@@ -195,7 +195,8 @@
The base address of exception vectors.
config ARM_PATCH_PHYS_VIRT
- bool "Patch physical to virtual translations at runtime"
+ bool "Patch physical to virtual translations at runtime" if EMBEDDED
+ default y
depends on !XIP_KERNEL && MMU
depends on !ARCH_REALVIEW || !SPARSEMEM
help
@@ -204,16 +205,12 @@
kernel in system memory.
This can only be used with non-XIP MMU kernels where the base
- of physical memory is at a 16MB boundary, or theoretically 64K
- for the MSM machine class.
+ of physical memory is at a 16MB boundary.
-config ARM_PATCH_PHYS_VIRT_16BIT
- def_bool y
- depends on ARM_PATCH_PHYS_VIRT && ARCH_MSM
- help
- This option extends the physical to virtual translation patching
- to allow physical memory down to a theoretical minimum of 64K
- boundaries.
+ Only disable this option if you know that you do not require
+ this feature (eg, building a kernel for a single machine) and
+ you need to shrink the kernel to the minimal size.
+
source "init/Kconfig"
@@ -301,7 +298,6 @@
select ARCH_REQUIRE_GPIOLIB
select HAVE_CLK
select CLKDEV_LOOKUP
- select ARM_PATCH_PHYS_VIRT if MMU
help
This enables support for systems based on the Atmel AT91RM9200,
AT91SAM9 and AT91CAP9 processors.
@@ -385,6 +381,7 @@
select CPU_SA110
select FOOTBRIDGE
select GENERIC_CLOCKEVENTS
+ select HAVE_IDE
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
@@ -631,6 +628,8 @@
select SPARSE_IRQ
select AUTO_ZRELADDR
select MULTI_IRQ_HANDLER
+ select ARM_CPU_SUSPEND if PM
+ select HAVE_IDE
help
Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
@@ -671,6 +670,7 @@
select NO_IOPORT
select ARCH_SPARSEMEM_ENABLE
select ARCH_USES_GETTIMEOFFSET
+ select HAVE_IDE
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -689,6 +689,7 @@
select HAVE_SCHED_CLOCK
select TICK_ONESHOT
select ARCH_REQUIRE_GPIOLIB
+ select HAVE_IDE
help
Support for StrongARM 11x0 based boards.
@@ -1375,6 +1376,7 @@
MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \
ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE
+ depends on MMU
select USE_GENERIC_SMP_HELPERS
select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
help
@@ -1407,6 +1409,31 @@
If you don't know what to do here, say Y.
+config ARM_CPU_TOPOLOGY
+ bool "Support cpu topology definition"
+ depends on SMP && CPU_V7
+ default y
+ help
+ Support ARM cpu topology definition. The MPIDR register defines
+ affinity between processors which is then used to describe the cpu
+ topology of an ARM System.
+
+config SCHED_MC
+ bool "Multi-core scheduler support"
+ depends on ARM_CPU_TOPOLOGY
+ help
+ Multi-core scheduler support improves the CPU scheduler's decision
+ making when dealing with multi-core CPU chips at a cost of slightly
+ increased overhead in some places. If unsure say N here.
+
+config SCHED_SMT
+ bool "SMT scheduler support"
+ depends on ARM_CPU_TOPOLOGY
+ help
+ Improves the CPU scheduler's decision making when dealing with
+ MultiThreading at a cost of slightly increased overhead in some
+ places. If unsure say N here.
+
config HAVE_ARM_SCU
bool
help
@@ -1482,6 +1509,7 @@
depends on CPU_V7 && !CPU_V6 && !CPU_V6K && EXPERIMENTAL
select AEABI
select ARM_ASM_UNIFIED
+ select ARM_UNWIND
help
By enabling this option, the kernel will be compiled in
Thumb-2 mode. A compiler/assembler that understand the unified
@@ -2101,6 +2129,9 @@
CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE
def_bool y
+config ARM_CPU_SUSPEND
+ def_bool PM_SLEEP
+
endmenu
source "net/Kconfig"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 81cbe40..df3eb3c 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -65,13 +65,71 @@
# These options are only for real kernel hackers who want to get their hands dirty.
config DEBUG_LL
- bool "Kernel low-level debugging functions"
+ bool "Kernel low-level debugging functions (read help!)"
depends on DEBUG_KERNEL
help
Say Y here to include definitions of printascii, printch, printhex
in the kernel. This is helpful if you are debugging code that
executes before the console is initialized.
+ Note that selecting this option will limit the kernel to a single
+ UART definition, as specified below. Attempting to boot the kernel
+ image on a different platform *will not work*, so this option should
+ not be enabled for kernels that are intended to be portable.
+
+choice
+ prompt "Kernel low-level debugging port"
+ depends on DEBUG_LL
+
+ config DEBUG_LL_UART_NONE
+ bool "No low-level debugging UART"
+ help
+ Say Y here if your platform doesn't provide a UART option
+ below. This relies on your platform choosing the right UART
+ definition internally in order for low-level debugging to
+ work.
+
+ config DEBUG_ICEDCC
+ bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the EmbeddedICE macrocell's DCC channel using
+ co-processor 14. This is known to work on the ARM9 style ICE
+ channel and on the XScale with the PEEDI.
+
+ Note that the system will appear to hang during boot if there
+ is nothing connected to read from the DCC.
+
+ config DEBUG_FOOTBRIDGE_COM1
+ bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+ depends on FOOTBRIDGE
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the 8250 at PCI COM1.
+
+ config DEBUG_DC21285_PORT
+ bool "Kernel low-level debugging messages via footbridge serial port"
+ depends on FOOTBRIDGE
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port in the DC21285 (Footbridge).
+
+ config DEBUG_CLPS711X_UART1
+ bool "Kernel low-level debugging messages via UART1"
+ depends on ARCH_CLPS711X
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the first serial port on these devices.
+
+ config DEBUG_CLPS711X_UART2
+ bool "Kernel low-level debugging messages via UART2"
+ depends on ARCH_CLPS711X
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the second serial port on these devices.
+
+endchoice
+
config EARLY_PRINTK
bool "Early printk"
depends on DEBUG_LL
@@ -80,43 +138,14 @@
kernel low-level debugging functions. Add earlyprintk to your
kernel parameters to enable this console.
-config DEBUG_ICEDCC
- bool "Kernel low-level debugging via EmbeddedICE DCC channel"
- depends on DEBUG_LL
- help
- Say Y here if you want the debug print routines to direct their
- output to the EmbeddedICE macrocell's DCC channel using
- co-processor 14. This is known to work on the ARM9 style ICE
- channel and on the XScale with the PEEDI.
-
- It does include a timeout to ensure that the system does not
- totally freeze when there is nothing connected to read.
-
config OC_ETM
bool "On-chip ETM and ETB"
- select ARM_AMBA
+ depends on ARM_AMBA
help
Enables the on-chip embedded trace macrocell and embedded trace
buffer driver that will allow you to collect traces of the
kernel code.
-config DEBUG_DC21285_PORT
- bool "Kernel low-level debugging messages via footbridge serial port"
- depends on DEBUG_LL && FOOTBRIDGE
- help
- Say Y here if you want the debug print routines to direct their
- output to the serial port in the DC21285 (Footbridge). Saying N
- will cause the debug messages to appear on the first 16550
- serial port.
-
-config DEBUG_CLPS711X_UART2
- bool "Kernel low-level debugging messages via UART2"
- depends on DEBUG_LL && ARCH_CLPS711X
- help
- Say Y here if you want the debug print routines to direct their
- output to the second serial port on these devices. Saying N will
- cause the debug messages to appear on the first serial port.
-
config DEBUG_S3C_UART
depends on PLAT_SAMSUNG
int "S3C UART to use for low-level debug"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 70c424e..5665c2a 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -128,6 +128,9 @@
ifeq ($(CONFIG_ARCH_SA1100),y)
textofs-$(CONFIG_SA1111) := 0x00208000
endif
+textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
# Machine directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c
index 3227ca9..666b278 100644
--- a/arch/arm/common/gic.c
+++ b/arch/arm/common/gic.c
@@ -180,7 +180,7 @@
return -EINVAL;
mask = 0xff << shift;
- bit = 1 << (cpu + shift);
+ bit = 1 << (cpu_logical_map(cpu) + shift);
spin_lock(&irq_controller_lock);
val = readl_relaxed(reg) & ~mask;
@@ -259,9 +259,15 @@
unsigned int irq_start)
{
unsigned int gic_irqs, irq_limit, i;
+ u32 cpumask;
void __iomem *base = gic->dist_base;
- u32 cpumask = 1 << smp_processor_id();
+ u32 cpu = 0;
+#ifdef CONFIG_SMP
+ cpu = cpu_logical_map(smp_processor_id());
+#endif
+
+ cpumask = 1 << cpu;
cpumask |= cpumask << 8;
cpumask |= cpumask << 16;
@@ -382,7 +388,12 @@
#ifdef CONFIG_SMP
void gic_raise_softirq(const struct cpumask *mask, unsigned int irq)
{
- unsigned long map = *cpus_addr(*mask);
+ int cpu;
+ unsigned long map = 0;
+
+ /* Convert our logical CPU mask into a physical one. */
+ for_each_cpu(cpu, mask)
+ map |= 1 << cpu_logical_map(cpu);
/*
* Ensure that stores to Normal memory are visible to the
diff --git a/arch/arm/common/vic.c b/arch/arm/common/vic.c
index 197f81c..01f18a4 100644
--- a/arch/arm/common/vic.c
+++ b/arch/arm/common/vic.c
@@ -346,7 +346,8 @@
/* Identify which VIC cell this one is, by reading the ID */
for (i = 0; i < 4; i++) {
- u32 addr = ((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
+ void __iomem *addr;
+ addr = (void __iomem *)((u32)base & PAGE_MASK) + 0xfe0 + (i * 4);
cellid |= (readl(addr) & 0xff) << (8 * i);
}
vendor = (cellid >> 12) & 0xff;
diff --git a/arch/arm/include/asm/cputype.h b/arch/arm/include/asm/cputype.h
index cd4458f..cb47d28 100644
--- a/arch/arm/include/asm/cputype.h
+++ b/arch/arm/include/asm/cputype.h
@@ -8,6 +8,7 @@
#define CPUID_CACHETYPE 1
#define CPUID_TCM 2
#define CPUID_TLBTYPE 3
+#define CPUID_MPIDR 5
#define CPUID_EXT_PFR0 "c1, 0"
#define CPUID_EXT_PFR1 "c1, 1"
@@ -70,6 +71,11 @@
return read_cpuid(CPUID_TCM);
}
+static inline unsigned int __attribute_const__ read_cpuid_mpidr(void)
+{
+ return read_cpuid(CPUID_MPIDR);
+}
+
/*
* Intel's XScale3 core supports some v6 features (supersections, L2)
* but advertises itself as v5 as it does not support the v6 ISA. For
diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h
index 7a21d0b..28b7ee8 100644
--- a/arch/arm/include/asm/dma-mapping.h
+++ b/arch/arm/include/asm/dma-mapping.h
@@ -32,7 +32,7 @@
static inline void *dma_to_virt(struct device *dev, dma_addr_t addr)
{
- return (void *)__bus_to_virt(addr);
+ return (void *)__bus_to_virt((unsigned long)addr);
}
static inline dma_addr_t virt_to_dma(struct device *dev, void *addr)
diff --git a/arch/arm/include/asm/ecard.h b/arch/arm/include/asm/ecard.h
index 29f2610..eaea146 100644
--- a/arch/arm/include/asm/ecard.h
+++ b/arch/arm/include/asm/ecard.h
@@ -161,7 +161,6 @@
/* Private internal data */
const char *card_desc; /* Card description */
- CONST unsigned int podaddr; /* Base Linux address for card */
CONST loader_t loader; /* loader program */
u64 dma_mask;
};
diff --git a/arch/arm/include/asm/exception.h b/arch/arm/include/asm/exception.h
new file mode 100644
index 0000000..5abaf5b
--- /dev/null
+++ b/arch/arm/include/asm/exception.h
@@ -0,0 +1,19 @@
+/*
+ * Annotations for marking C functions as exception handlers.
+ *
+ * These should only be used for C functions that are called from the low
+ * level exception entry code and not any intervening C code.
+ */
+#ifndef __ASM_ARM_EXCEPTION_H
+#define __ASM_ARM_EXCEPTION_H
+
+#include <linux/ftrace.h>
+
+#define __exception __attribute__((section(".exception.text")))
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+#define __exception_irq_entry __irq_entry
+#else
+#define __exception_irq_entry __exception
+#endif
+
+#endif /* __ASM_ARM_EXCEPTION_H */
diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h
index 99a6ed7..434edcc 100644
--- a/arch/arm/include/asm/hardware/cache-l2x0.h
+++ b/arch/arm/include/asm/hardware/cache-l2x0.h
@@ -52,6 +52,8 @@
#define L2X0_LOCKDOWN_WAY_D_BASE 0x900
#define L2X0_LOCKDOWN_WAY_I_BASE 0x904
#define L2X0_LOCKDOWN_STRIDE 0x08
+#define L2X0_ADDR_FILTER_START 0xC00
+#define L2X0_ADDR_FILTER_END 0xC04
#define L2X0_TEST_OPERATION 0xF00
#define L2X0_LINE_DATA 0xF10
#define L2X0_LINE_TAG 0xF30
@@ -65,8 +67,23 @@
#define L2X0_CACHE_ID_PART_MASK (0xf << 6)
#define L2X0_CACHE_ID_PART_L210 (1 << 6)
#define L2X0_CACHE_ID_PART_L310 (3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK 0x3f
+#define L2X0_CACHE_ID_RTL_R0P0 0x0
+#define L2X0_CACHE_ID_RTL_R1P0 0x2
+#define L2X0_CACHE_ID_RTL_R2P0 0x4
+#define L2X0_CACHE_ID_RTL_R3P0 0x5
+#define L2X0_CACHE_ID_RTL_R3P1 0x6
+#define L2X0_CACHE_ID_RTL_R3P2 0x8
#define L2X0_AUX_CTRL_MASK 0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT 0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK 0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT 3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK (0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT 6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK (0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT 9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK (0x7 << 9)
#define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16
#define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17
#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17)
@@ -77,8 +94,33 @@
#define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT 29
#define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT 30
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT 0
+#define L2X0_LATENCY_CTRL_RD_SHIFT 4
+#define L2X0_LATENCY_CTRL_WR_SHIFT 8
+
+#define L2X0_ADDR_FILTER_EN 1
+
#ifndef __ASSEMBLY__
extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+
+struct l2x0_regs {
+ unsigned long phy_base;
+ unsigned long aux_ctrl;
+ /*
+ * Whether the following registers need to be saved/restored
+ * depends on platform
+ */
+ unsigned long tag_latency;
+ unsigned long data_latency;
+ unsigned long filter_start;
+ unsigned long filter_end;
+ unsigned long prefetch_ctrl;
+ unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
#endif
#endif
diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h
index d66605d..dc2d510 100644
--- a/arch/arm/include/asm/io.h
+++ b/arch/arm/include/asm/io.h
@@ -110,6 +110,27 @@
#include <mach/io.h>
/*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support. Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space. Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
+/*
* IO port access primitives
* -------------------------
*
@@ -260,10 +281,16 @@
#define ioread16(p) ({ unsigned int __v = le16_to_cpu((__force __le16)__raw_readw(p)); __iormb(); __v; })
#define ioread32(p) ({ unsigned int __v = le32_to_cpu((__force __le32)__raw_readl(p)); __iormb(); __v; })
+#define ioread16be(p) ({ unsigned int __v = be16_to_cpu((__force __be16)__raw_readw(p)); __iormb(); __v; })
+#define ioread32be(p) ({ unsigned int __v = be32_to_cpu((__force __be32)__raw_readl(p)); __iormb(); __v; })
+
#define iowrite8(v,p) ({ __iowmb(); (void)__raw_writeb(v, p); })
#define iowrite16(v,p) ({ __iowmb(); (void)__raw_writew((__force __u16)cpu_to_le16(v), p); })
#define iowrite32(v,p) ({ __iowmb(); (void)__raw_writel((__force __u32)cpu_to_le32(v), p); })
+#define iowrite16be(v,p) ({ __iowmb(); (void)__raw_writew((__force __u16)cpu_to_be16(v), p); })
+#define iowrite32be(v,p) ({ __iowmb(); (void)__raw_writel((__force __u32)cpu_to_be32(v), p); })
+
#define ioread8_rep(p,d,c) __raw_readsb(p,d,c)
#define ioread16_rep(p,d,c) __raw_readsw(p,d,c)
#define ioread32_rep(p,d,c) __raw_readsl(p,d,c)
diff --git a/arch/arm/include/asm/localtimer.h b/arch/arm/include/asm/localtimer.h
index ff66638..6fd955d 100644
--- a/arch/arm/include/asm/localtimer.h
+++ b/arch/arm/include/asm/localtimer.h
@@ -24,6 +24,10 @@
*/
asmlinkage void do_local_timer(struct pt_regs *);
+/*
+ * Called from C code
+ */
+void handle_local_timer(struct pt_regs *);
#ifdef CONFIG_LOCAL_TIMERS
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index b8de516..441fc4f 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -160,7 +160,6 @@
* so that all we need to do is modify the 8-bit constant field.
*/
#define __PV_BITS_31_24 0x81000000
-#define __PV_BITS_23_16 0x00810000
extern unsigned long __pv_phys_offset;
#define PHYS_OFFSET __pv_phys_offset
@@ -178,9 +177,6 @@
{
unsigned long t;
__pv_stub(x, t, "add", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- __pv_stub(t, t, "add", __PV_BITS_23_16);
-#endif
return t;
}
@@ -188,9 +184,6 @@
{
unsigned long t;
__pv_stub(x, t, "sub", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- __pv_stub(t, t, "sub", __PV_BITS_23_16);
-#endif
return t;
}
#else
diff --git a/arch/arm/include/asm/module.h b/arch/arm/include/asm/module.h
index 543b449..6c6809f 100644
--- a/arch/arm/include/asm/module.h
+++ b/arch/arm/include/asm/module.h
@@ -31,11 +31,7 @@
/* Add __virt_to_phys patching state as well */
#ifdef CONFIG_ARM_PATCH_PHYS_VIRT
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-#define MODULE_ARCH_VERMAGIC_P2V "p2v16 "
-#else
#define MODULE_ARCH_VERMAGIC_P2V "p2v8 "
-#endif
#else
#define MODULE_ARCH_VERMAGIC_P2V ""
#endif
diff --git a/arch/arm/include/asm/outercache.h b/arch/arm/include/asm/outercache.h
index d838743..53426c6 100644
--- a/arch/arm/include/asm/outercache.h
+++ b/arch/arm/include/asm/outercache.h
@@ -34,6 +34,7 @@
void (*sync)(void);
#endif
void (*set_debug)(unsigned long);
+ void (*resume)(void);
};
#ifdef CONFIG_OUTER_CACHE
@@ -74,6 +75,12 @@
outer_cache.disable();
}
+static inline void outer_resume(void)
+{
+ if (outer_cache.resume)
+ outer_cache.resume();
+}
+
#else
static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)
diff --git a/arch/arm/include/asm/page.h b/arch/arm/include/asm/page.h
index ac75d08..ca94653 100644
--- a/arch/arm/include/asm/page.h
+++ b/arch/arm/include/asm/page.h
@@ -151,47 +151,7 @@
#define clear_page(page) memset((void *)(page), 0, PAGE_SIZE)
extern void copy_page(void *to, const void *from);
-typedef unsigned long pteval_t;
-
-#undef STRICT_MM_TYPECHECKS
-
-#ifdef STRICT_MM_TYPECHECKS
-/*
- * These are used to make use of C type-checking..
- */
-typedef struct { pteval_t pte; } pte_t;
-typedef struct { unsigned long pmd; } pmd_t;
-typedef struct { unsigned long pgd[2]; } pgd_t;
-typedef struct { unsigned long pgprot; } pgprot_t;
-
-#define pte_val(x) ((x).pte)
-#define pmd_val(x) ((x).pmd)
-#define pgd_val(x) ((x).pgd[0])
-#define pgprot_val(x) ((x).pgprot)
-
-#define __pte(x) ((pte_t) { (x) } )
-#define __pmd(x) ((pmd_t) { (x) } )
-#define __pgprot(x) ((pgprot_t) { (x) } )
-
-#else
-/*
- * .. while these make it easier on the compiler
- */
-typedef pteval_t pte_t;
-typedef unsigned long pmd_t;
-typedef unsigned long pgd_t[2];
-typedef unsigned long pgprot_t;
-
-#define pte_val(x) (x)
-#define pmd_val(x) (x)
-#define pgd_val(x) ((x)[0])
-#define pgprot_val(x) (x)
-
-#define __pte(x) (x)
-#define __pmd(x) (x)
-#define __pgprot(x) (x)
-
-#endif /* STRICT_MM_TYPECHECKS */
+#include <asm/pgtable-2level-types.h>
#endif /* CONFIG_MMU */
diff --git a/arch/arm/include/asm/pgalloc.h b/arch/arm/include/asm/pgalloc.h
index 22de005..3e08fd3 100644
--- a/arch/arm/include/asm/pgalloc.h
+++ b/arch/arm/include/asm/pgalloc.h
@@ -105,9 +105,9 @@
}
static inline void __pmd_populate(pmd_t *pmdp, phys_addr_t pte,
- unsigned long prot)
+ pmdval_t prot)
{
- unsigned long pmdval = (pte + PTE_HWTABLE_OFF) | prot;
+ pmdval_t pmdval = (pte + PTE_HWTABLE_OFF) | prot;
pmdp[0] = __pmd(pmdval);
pmdp[1] = __pmd(pmdval + 256 * sizeof(pte_t));
flush_pmd_entry(pmdp);
diff --git a/arch/arm/include/asm/pgtable-2level-hwdef.h b/arch/arm/include/asm/pgtable-2level-hwdef.h
new file mode 100644
index 0000000..5cfba15
--- /dev/null
+++ b/arch/arm/include/asm/pgtable-2level-hwdef.h
@@ -0,0 +1,93 @@
+/*
+ * arch/arm/include/asm/pgtable-2level-hwdef.h
+ *
+ * Copyright (C) 1995-2002 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef _ASM_PGTABLE_2LEVEL_HWDEF_H
+#define _ASM_PGTABLE_2LEVEL_HWDEF_H
+
+/*
+ * Hardware page table definitions.
+ *
+ * + Level 1 descriptor (PMD)
+ * - common
+ */
+#define PMD_TYPE_MASK (_AT(pmdval_t, 3) << 0)
+#define PMD_TYPE_FAULT (_AT(pmdval_t, 0) << 0)
+#define PMD_TYPE_TABLE (_AT(pmdval_t, 1) << 0)
+#define PMD_TYPE_SECT (_AT(pmdval_t, 2) << 0)
+#define PMD_BIT4 (_AT(pmdval_t, 1) << 4)
+#define PMD_DOMAIN(x) (_AT(pmdval_t, (x)) << 5)
+#define PMD_PROTECTION (_AT(pmdval_t, 1) << 9) /* v5 */
+/*
+ * - section
+ */
+#define PMD_SECT_BUFFERABLE (_AT(pmdval_t, 1) << 2)
+#define PMD_SECT_CACHEABLE (_AT(pmdval_t, 1) << 3)
+#define PMD_SECT_XN (_AT(pmdval_t, 1) << 4) /* v6 */
+#define PMD_SECT_AP_WRITE (_AT(pmdval_t, 1) << 10)
+#define PMD_SECT_AP_READ (_AT(pmdval_t, 1) << 11)
+#define PMD_SECT_TEX(x) (_AT(pmdval_t, (x)) << 12) /* v5 */
+#define PMD_SECT_APX (_AT(pmdval_t, 1) << 15) /* v6 */
+#define PMD_SECT_S (_AT(pmdval_t, 1) << 16) /* v6 */
+#define PMD_SECT_nG (_AT(pmdval_t, 1) << 17) /* v6 */
+#define PMD_SECT_SUPER (_AT(pmdval_t, 1) << 18) /* v6 */
+#define PMD_SECT_AF (_AT(pmdval_t, 0))
+
+#define PMD_SECT_UNCACHED (_AT(pmdval_t, 0))
+#define PMD_SECT_BUFFERED (PMD_SECT_BUFFERABLE)
+#define PMD_SECT_WT (PMD_SECT_CACHEABLE)
+#define PMD_SECT_WB (PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE)
+#define PMD_SECT_MINICACHE (PMD_SECT_TEX(1) | PMD_SECT_CACHEABLE)
+#define PMD_SECT_WBWA (PMD_SECT_TEX(1) | PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE)
+#define PMD_SECT_NONSHARED_DEV (PMD_SECT_TEX(2))
+
+/*
+ * - coarse table (not used)
+ */
+
+/*
+ * + Level 2 descriptor (PTE)
+ * - common
+ */
+#define PTE_TYPE_MASK (_AT(pteval_t, 3) << 0)
+#define PTE_TYPE_FAULT (_AT(pteval_t, 0) << 0)
+#define PTE_TYPE_LARGE (_AT(pteval_t, 1) << 0)
+#define PTE_TYPE_SMALL (_AT(pteval_t, 2) << 0)
+#define PTE_TYPE_EXT (_AT(pteval_t, 3) << 0) /* v5 */
+#define PTE_BUFFERABLE (_AT(pteval_t, 1) << 2)
+#define PTE_CACHEABLE (_AT(pteval_t, 1) << 3)
+
+/*
+ * - extended small page/tiny page
+ */
+#define PTE_EXT_XN (_AT(pteval_t, 1) << 0) /* v6 */
+#define PTE_EXT_AP_MASK (_AT(pteval_t, 3) << 4)
+#define PTE_EXT_AP0 (_AT(pteval_t, 1) << 4)
+#define PTE_EXT_AP1 (_AT(pteval_t, 2) << 4)
+#define PTE_EXT_AP_UNO_SRO (_AT(pteval_t, 0) << 4)
+#define PTE_EXT_AP_UNO_SRW (PTE_EXT_AP0)
+#define PTE_EXT_AP_URO_SRW (PTE_EXT_AP1)
+#define PTE_EXT_AP_URW_SRW (PTE_EXT_AP1|PTE_EXT_AP0)
+#define PTE_EXT_TEX(x) (_AT(pteval_t, (x)) << 6) /* v5 */
+#define PTE_EXT_APX (_AT(pteval_t, 1) << 9) /* v6 */
+#define PTE_EXT_COHERENT (_AT(pteval_t, 1) << 9) /* XScale3 */
+#define PTE_EXT_SHARED (_AT(pteval_t, 1) << 10) /* v6 */
+#define PTE_EXT_NG (_AT(pteval_t, 1) << 11) /* v6 */
+
+/*
+ * - small page
+ */
+#define PTE_SMALL_AP_MASK (_AT(pteval_t, 0xff) << 4)
+#define PTE_SMALL_AP_UNO_SRO (_AT(pteval_t, 0x00) << 4)
+#define PTE_SMALL_AP_UNO_SRW (_AT(pteval_t, 0x55) << 4)
+#define PTE_SMALL_AP_URO_SRW (_AT(pteval_t, 0xaa) << 4)
+#define PTE_SMALL_AP_URW_SRW (_AT(pteval_t, 0xff) << 4)
+
+#define PHYS_MASK (~0UL)
+
+#endif
diff --git a/arch/arm/include/asm/pgtable-2level-types.h b/arch/arm/include/asm/pgtable-2level-types.h
new file mode 100644
index 0000000..66cb5b0
--- /dev/null
+++ b/arch/arm/include/asm/pgtable-2level-types.h
@@ -0,0 +1,67 @@
+/*
+ * arch/arm/include/asm/pgtable-2level-types.h
+ *
+ * Copyright (C) 1995-2003 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef _ASM_PGTABLE_2LEVEL_TYPES_H
+#define _ASM_PGTABLE_2LEVEL_TYPES_H
+
+#include <asm/types.h>
+
+typedef u32 pteval_t;
+typedef u32 pmdval_t;
+
+#undef STRICT_MM_TYPECHECKS
+
+#ifdef STRICT_MM_TYPECHECKS
+/*
+ * These are used to make use of C type-checking..
+ */
+typedef struct { pteval_t pte; } pte_t;
+typedef struct { pmdval_t pmd; } pmd_t;
+typedef struct { pmdval_t pgd[2]; } pgd_t;
+typedef struct { pteval_t pgprot; } pgprot_t;
+
+#define pte_val(x) ((x).pte)
+#define pmd_val(x) ((x).pmd)
+#define pgd_val(x) ((x).pgd[0])
+#define pgprot_val(x) ((x).pgprot)
+
+#define __pte(x) ((pte_t) { (x) } )
+#define __pmd(x) ((pmd_t) { (x) } )
+#define __pgprot(x) ((pgprot_t) { (x) } )
+
+#else
+/*
+ * .. while these make it easier on the compiler
+ */
+typedef pteval_t pte_t;
+typedef pmdval_t pmd_t;
+typedef pmdval_t pgd_t[2];
+typedef pteval_t pgprot_t;
+
+#define pte_val(x) (x)
+#define pmd_val(x) (x)
+#define pgd_val(x) ((x)[0])
+#define pgprot_val(x) (x)
+
+#define __pte(x) (x)
+#define __pmd(x) (x)
+#define __pgprot(x) (x)
+
+#endif /* STRICT_MM_TYPECHECKS */
+
+#endif /* _ASM_PGTABLE_2LEVEL_TYPES_H */
diff --git a/arch/arm/include/asm/pgtable-2level.h b/arch/arm/include/asm/pgtable-2level.h
new file mode 100644
index 0000000..470457e
--- /dev/null
+++ b/arch/arm/include/asm/pgtable-2level.h
@@ -0,0 +1,143 @@
+/*
+ * arch/arm/include/asm/pgtable-2level.h
+ *
+ * Copyright (C) 1995-2002 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef _ASM_PGTABLE_2LEVEL_H
+#define _ASM_PGTABLE_2LEVEL_H
+
+/*
+ * Hardware-wise, we have a two level page table structure, where the first
+ * level has 4096 entries, and the second level has 256 entries. Each entry
+ * is one 32-bit word. Most of the bits in the second level entry are used
+ * by hardware, and there aren't any "accessed" and "dirty" bits.
+ *
+ * Linux on the other hand has a three level page table structure, which can
+ * be wrapped to fit a two level page table structure easily - using the PGD
+ * and PTE only. However, Linux also expects one "PTE" table per page, and
+ * at least a "dirty" bit.
+ *
+ * Therefore, we tweak the implementation slightly - we tell Linux that we
+ * have 2048 entries in the first level, each of which is 8 bytes (iow, two
+ * hardware pointers to the second level.) The second level contains two
+ * hardware PTE tables arranged contiguously, preceded by Linux versions
+ * which contain the state information Linux needs. We, therefore, end up
+ * with 512 entries in the "PTE" level.
+ *
+ * This leads to the page tables having the following layout:
+ *
+ * pgd pte
+ * | |
+ * +--------+
+ * | | +------------+ +0
+ * +- - - - + | Linux pt 0 |
+ * | | +------------+ +1024
+ * +--------+ +0 | Linux pt 1 |
+ * | |-----> +------------+ +2048
+ * +- - - - + +4 | h/w pt 0 |
+ * | |-----> +------------+ +3072
+ * +--------+ +8 | h/w pt 1 |
+ * | | +------------+ +4096
+ *
+ * See L_PTE_xxx below for definitions of bits in the "Linux pt", and
+ * PTE_xxx for definitions of bits appearing in the "h/w pt".
+ *
+ * PMD_xxx definitions refer to bits in the first level page table.
+ *
+ * The "dirty" bit is emulated by only granting hardware write permission
+ * iff the page is marked "writable" and "dirty" in the Linux PTE. This
+ * means that a write to a clean page will cause a permission fault, and
+ * the Linux MM layer will mark the page dirty via handle_pte_fault().
+ * For the hardware to notice the permission change, the TLB entry must
+ * be flushed, and ptep_set_access_flags() does that for us.
+ *
+ * The "accessed" or "young" bit is emulated by a similar method; we only
+ * allow accesses to the page if the "young" bit is set. Accesses to the
+ * page will cause a fault, and handle_pte_fault() will set the young bit
+ * for us as long as the page is marked present in the corresponding Linux
+ * PTE entry. Again, ptep_set_access_flags() will ensure that the TLB is
+ * up to date.
+ *
+ * However, when the "young" bit is cleared, we deny access to the page
+ * by clearing the hardware PTE. Currently Linux does not flush the TLB
+ * for us in this case, which means the TLB will retain the transation
+ * until either the TLB entry is evicted under pressure, or a context
+ * switch which changes the user space mapping occurs.
+ */
+#define PTRS_PER_PTE 512
+#define PTRS_PER_PMD 1
+#define PTRS_PER_PGD 2048
+
+#define PTE_HWTABLE_PTRS (PTRS_PER_PTE)
+#define PTE_HWTABLE_OFF (PTE_HWTABLE_PTRS * sizeof(pte_t))
+#define PTE_HWTABLE_SIZE (PTRS_PER_PTE * sizeof(u32))
+
+/*
+ * PMD_SHIFT determines the size of the area a second-level page table can map
+ * PGDIR_SHIFT determines what a third-level page table entry can map
+ */
+#define PMD_SHIFT 21
+#define PGDIR_SHIFT 21
+
+#define PMD_SIZE (1UL << PMD_SHIFT)
+#define PMD_MASK (~(PMD_SIZE-1))
+#define PGDIR_SIZE (1UL << PGDIR_SHIFT)
+#define PGDIR_MASK (~(PGDIR_SIZE-1))
+
+/*
+ * section address mask and size definitions.
+ */
+#define SECTION_SHIFT 20
+#define SECTION_SIZE (1UL << SECTION_SHIFT)
+#define SECTION_MASK (~(SECTION_SIZE-1))
+
+/*
+ * ARMv6 supersection address mask and size definitions.
+ */
+#define SUPERSECTION_SHIFT 24
+#define SUPERSECTION_SIZE (1UL << SUPERSECTION_SHIFT)
+#define SUPERSECTION_MASK (~(SUPERSECTION_SIZE-1))
+
+#define USER_PTRS_PER_PGD (TASK_SIZE / PGDIR_SIZE)
+
+/*
+ * "Linux" PTE definitions.
+ *
+ * We keep two sets of PTEs - the hardware and the linux version.
+ * This allows greater flexibility in the way we map the Linux bits
+ * onto the hardware tables, and allows us to have YOUNG and DIRTY
+ * bits.
+ *
+ * The PTE table pointer refers to the hardware entries; the "Linux"
+ * entries are stored 1024 bytes below.
+ */
+#define L_PTE_PRESENT (_AT(pteval_t, 1) << 0)
+#define L_PTE_YOUNG (_AT(pteval_t, 1) << 1)
+#define L_PTE_FILE (_AT(pteval_t, 1) << 2) /* only when !PRESENT */
+#define L_PTE_DIRTY (_AT(pteval_t, 1) << 6)
+#define L_PTE_RDONLY (_AT(pteval_t, 1) << 7)
+#define L_PTE_USER (_AT(pteval_t, 1) << 8)
+#define L_PTE_XN (_AT(pteval_t, 1) << 9)
+#define L_PTE_SHARED (_AT(pteval_t, 1) << 10) /* shared(v6), coherent(xsc3) */
+
+/*
+ * These are the memory types, defined to be compatible with
+ * pre-ARMv6 CPUs cacheable and bufferable bits: XXCB
+ */
+#define L_PTE_MT_UNCACHED (_AT(pteval_t, 0x00) << 2) /* 0000 */
+#define L_PTE_MT_BUFFERABLE (_AT(pteval_t, 0x01) << 2) /* 0001 */
+#define L_PTE_MT_WRITETHROUGH (_AT(pteval_t, 0x02) << 2) /* 0010 */
+#define L_PTE_MT_WRITEBACK (_AT(pteval_t, 0x03) << 2) /* 0011 */
+#define L_PTE_MT_MINICACHE (_AT(pteval_t, 0x06) << 2) /* 0110 (sa1100, xscale) */
+#define L_PTE_MT_WRITEALLOC (_AT(pteval_t, 0x07) << 2) /* 0111 */
+#define L_PTE_MT_DEV_SHARED (_AT(pteval_t, 0x04) << 2) /* 0100 */
+#define L_PTE_MT_DEV_NONSHARED (_AT(pteval_t, 0x0c) << 2) /* 1100 */
+#define L_PTE_MT_DEV_WC (_AT(pteval_t, 0x09) << 2) /* 1001 */
+#define L_PTE_MT_DEV_CACHED (_AT(pteval_t, 0x0b) << 2) /* 1011 */
+#define L_PTE_MT_MASK (_AT(pteval_t, 0x0f) << 2)
+
+#endif /* _ASM_PGTABLE_2LEVEL_H */
diff --git a/arch/arm/include/asm/pgtable-hwdef.h b/arch/arm/include/asm/pgtable-hwdef.h
index fd1521d..1831111 100644
--- a/arch/arm/include/asm/pgtable-hwdef.h
+++ b/arch/arm/include/asm/pgtable-hwdef.h
@@ -10,81 +10,6 @@
#ifndef _ASMARM_PGTABLE_HWDEF_H
#define _ASMARM_PGTABLE_HWDEF_H
-/*
- * Hardware page table definitions.
- *
- * + Level 1 descriptor (PMD)
- * - common
- */
-#define PMD_TYPE_MASK (3 << 0)
-#define PMD_TYPE_FAULT (0 << 0)
-#define PMD_TYPE_TABLE (1 << 0)
-#define PMD_TYPE_SECT (2 << 0)
-#define PMD_BIT4 (1 << 4)
-#define PMD_DOMAIN(x) ((x) << 5)
-#define PMD_PROTECTION (1 << 9) /* v5 */
-/*
- * - section
- */
-#define PMD_SECT_BUFFERABLE (1 << 2)
-#define PMD_SECT_CACHEABLE (1 << 3)
-#define PMD_SECT_XN (1 << 4) /* v6 */
-#define PMD_SECT_AP_WRITE (1 << 10)
-#define PMD_SECT_AP_READ (1 << 11)
-#define PMD_SECT_TEX(x) ((x) << 12) /* v5 */
-#define PMD_SECT_APX (1 << 15) /* v6 */
-#define PMD_SECT_S (1 << 16) /* v6 */
-#define PMD_SECT_nG (1 << 17) /* v6 */
-#define PMD_SECT_SUPER (1 << 18) /* v6 */
-
-#define PMD_SECT_UNCACHED (0)
-#define PMD_SECT_BUFFERED (PMD_SECT_BUFFERABLE)
-#define PMD_SECT_WT (PMD_SECT_CACHEABLE)
-#define PMD_SECT_WB (PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE)
-#define PMD_SECT_MINICACHE (PMD_SECT_TEX(1) | PMD_SECT_CACHEABLE)
-#define PMD_SECT_WBWA (PMD_SECT_TEX(1) | PMD_SECT_CACHEABLE | PMD_SECT_BUFFERABLE)
-#define PMD_SECT_NONSHARED_DEV (PMD_SECT_TEX(2))
-
-/*
- * - coarse table (not used)
- */
-
-/*
- * + Level 2 descriptor (PTE)
- * - common
- */
-#define PTE_TYPE_MASK (3 << 0)
-#define PTE_TYPE_FAULT (0 << 0)
-#define PTE_TYPE_LARGE (1 << 0)
-#define PTE_TYPE_SMALL (2 << 0)
-#define PTE_TYPE_EXT (3 << 0) /* v5 */
-#define PTE_BUFFERABLE (1 << 2)
-#define PTE_CACHEABLE (1 << 3)
-
-/*
- * - extended small page/tiny page
- */
-#define PTE_EXT_XN (1 << 0) /* v6 */
-#define PTE_EXT_AP_MASK (3 << 4)
-#define PTE_EXT_AP0 (1 << 4)
-#define PTE_EXT_AP1 (2 << 4)
-#define PTE_EXT_AP_UNO_SRO (0 << 4)
-#define PTE_EXT_AP_UNO_SRW (PTE_EXT_AP0)
-#define PTE_EXT_AP_URO_SRW (PTE_EXT_AP1)
-#define PTE_EXT_AP_URW_SRW (PTE_EXT_AP1|PTE_EXT_AP0)
-#define PTE_EXT_TEX(x) ((x) << 6) /* v5 */
-#define PTE_EXT_APX (1 << 9) /* v6 */
-#define PTE_EXT_COHERENT (1 << 9) /* XScale3 */
-#define PTE_EXT_SHARED (1 << 10) /* v6 */
-#define PTE_EXT_NG (1 << 11) /* v6 */
-
-/*
- * - small page
- */
-#define PTE_SMALL_AP_MASK (0xff << 4)
-#define PTE_SMALL_AP_UNO_SRO (0x00 << 4)
-#define PTE_SMALL_AP_UNO_SRW (0x55 << 4)
-#define PTE_SMALL_AP_URO_SRW (0xaa << 4)
-#define PTE_SMALL_AP_URW_SRW (0xff << 4)
+#include <asm/pgtable-2level-hwdef.h>
#endif
diff --git a/arch/arm/include/asm/pgtable.h b/arch/arm/include/asm/pgtable.h
index 5750704..8ade184 100644
--- a/arch/arm/include/asm/pgtable.h
+++ b/arch/arm/include/asm/pgtable.h
@@ -24,6 +24,8 @@
#include <mach/vmalloc.h>
#include <asm/pgtable-hwdef.h>
+#include <asm/pgtable-2level.h>
+
/*
* Just any arbitrary offset to the start of the vmalloc VM area: the
* current 8MB value just means that there will be a 8MB "hole" after the
@@ -41,79 +43,6 @@
#define VMALLOC_START (((unsigned long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))
#endif
-/*
- * Hardware-wise, we have a two level page table structure, where the first
- * level has 4096 entries, and the second level has 256 entries. Each entry
- * is one 32-bit word. Most of the bits in the second level entry are used
- * by hardware, and there aren't any "accessed" and "dirty" bits.
- *
- * Linux on the other hand has a three level page table structure, which can
- * be wrapped to fit a two level page table structure easily - using the PGD
- * and PTE only. However, Linux also expects one "PTE" table per page, and
- * at least a "dirty" bit.
- *
- * Therefore, we tweak the implementation slightly - we tell Linux that we
- * have 2048 entries in the first level, each of which is 8 bytes (iow, two
- * hardware pointers to the second level.) The second level contains two
- * hardware PTE tables arranged contiguously, preceded by Linux versions
- * which contain the state information Linux needs. We, therefore, end up
- * with 512 entries in the "PTE" level.
- *
- * This leads to the page tables having the following layout:
- *
- * pgd pte
- * | |
- * +--------+
- * | | +------------+ +0
- * +- - - - + | Linux pt 0 |
- * | | +------------+ +1024
- * +--------+ +0 | Linux pt 1 |
- * | |-----> +------------+ +2048
- * +- - - - + +4 | h/w pt 0 |
- * | |-----> +------------+ +3072
- * +--------+ +8 | h/w pt 1 |
- * | | +------------+ +4096
- *
- * See L_PTE_xxx below for definitions of bits in the "Linux pt", and
- * PTE_xxx for definitions of bits appearing in the "h/w pt".
- *
- * PMD_xxx definitions refer to bits in the first level page table.
- *
- * The "dirty" bit is emulated by only granting hardware write permission
- * iff the page is marked "writable" and "dirty" in the Linux PTE. This
- * means that a write to a clean page will cause a permission fault, and
- * the Linux MM layer will mark the page dirty via handle_pte_fault().
- * For the hardware to notice the permission change, the TLB entry must
- * be flushed, and ptep_set_access_flags() does that for us.
- *
- * The "accessed" or "young" bit is emulated by a similar method; we only
- * allow accesses to the page if the "young" bit is set. Accesses to the
- * page will cause a fault, and handle_pte_fault() will set the young bit
- * for us as long as the page is marked present in the corresponding Linux
- * PTE entry. Again, ptep_set_access_flags() will ensure that the TLB is
- * up to date.
- *
- * However, when the "young" bit is cleared, we deny access to the page
- * by clearing the hardware PTE. Currently Linux does not flush the TLB
- * for us in this case, which means the TLB will retain the transation
- * until either the TLB entry is evicted under pressure, or a context
- * switch which changes the user space mapping occurs.
- */
-#define PTRS_PER_PTE 512
-#define PTRS_PER_PMD 1
-#define PTRS_PER_PGD 2048
-
-#define PTE_HWTABLE_PTRS (PTRS_PER_PTE)
-#define PTE_HWTABLE_OFF (PTE_HWTABLE_PTRS * sizeof(pte_t))
-#define PTE_HWTABLE_SIZE (PTRS_PER_PTE * sizeof(u32))
-
-/*
- * PMD_SHIFT determines the size of the area a second-level page table can map
- * PGDIR_SHIFT determines what a third-level page table entry can map
- */
-#define PMD_SHIFT 21
-#define PGDIR_SHIFT 21
-
#define LIBRARY_TEXT_START 0x0c000000
#ifndef __ASSEMBLY__
@@ -124,12 +53,6 @@
#define pte_ERROR(pte) __pte_error(__FILE__, __LINE__, pte)
#define pmd_ERROR(pmd) __pmd_error(__FILE__, __LINE__, pmd)
#define pgd_ERROR(pgd) __pgd_error(__FILE__, __LINE__, pgd)
-#endif /* !__ASSEMBLY__ */
-
-#define PMD_SIZE (1UL << PMD_SHIFT)
-#define PMD_MASK (~(PMD_SIZE-1))
-#define PGDIR_SIZE (1UL << PGDIR_SHIFT)
-#define PGDIR_MASK (~(PGDIR_SIZE-1))
/*
* This is the lowest virtual address we can permit any user space
@@ -138,60 +61,6 @@
*/
#define FIRST_USER_ADDRESS PAGE_SIZE
-#define USER_PTRS_PER_PGD (TASK_SIZE / PGDIR_SIZE)
-
-/*
- * section address mask and size definitions.
- */
-#define SECTION_SHIFT 20
-#define SECTION_SIZE (1UL << SECTION_SHIFT)
-#define SECTION_MASK (~(SECTION_SIZE-1))
-
-/*
- * ARMv6 supersection address mask and size definitions.
- */
-#define SUPERSECTION_SHIFT 24
-#define SUPERSECTION_SIZE (1UL << SUPERSECTION_SHIFT)
-#define SUPERSECTION_MASK (~(SUPERSECTION_SIZE-1))
-
-/*
- * "Linux" PTE definitions.
- *
- * We keep two sets of PTEs - the hardware and the linux version.
- * This allows greater flexibility in the way we map the Linux bits
- * onto the hardware tables, and allows us to have YOUNG and DIRTY
- * bits.
- *
- * The PTE table pointer refers to the hardware entries; the "Linux"
- * entries are stored 1024 bytes below.
- */
-#define L_PTE_PRESENT (_AT(pteval_t, 1) << 0)
-#define L_PTE_YOUNG (_AT(pteval_t, 1) << 1)
-#define L_PTE_FILE (_AT(pteval_t, 1) << 2) /* only when !PRESENT */
-#define L_PTE_DIRTY (_AT(pteval_t, 1) << 6)
-#define L_PTE_RDONLY (_AT(pteval_t, 1) << 7)
-#define L_PTE_USER (_AT(pteval_t, 1) << 8)
-#define L_PTE_XN (_AT(pteval_t, 1) << 9)
-#define L_PTE_SHARED (_AT(pteval_t, 1) << 10) /* shared(v6), coherent(xsc3) */
-
-/*
- * These are the memory types, defined to be compatible with
- * pre-ARMv6 CPUs cacheable and bufferable bits: XXCB
- */
-#define L_PTE_MT_UNCACHED (_AT(pteval_t, 0x00) << 2) /* 0000 */
-#define L_PTE_MT_BUFFERABLE (_AT(pteval_t, 0x01) << 2) /* 0001 */
-#define L_PTE_MT_WRITETHROUGH (_AT(pteval_t, 0x02) << 2) /* 0010 */
-#define L_PTE_MT_WRITEBACK (_AT(pteval_t, 0x03) << 2) /* 0011 */
-#define L_PTE_MT_MINICACHE (_AT(pteval_t, 0x06) << 2) /* 0110 (sa1100, xscale) */
-#define L_PTE_MT_WRITEALLOC (_AT(pteval_t, 0x07) << 2) /* 0111 */
-#define L_PTE_MT_DEV_SHARED (_AT(pteval_t, 0x04) << 2) /* 0100 */
-#define L_PTE_MT_DEV_NONSHARED (_AT(pteval_t, 0x0c) << 2) /* 1100 */
-#define L_PTE_MT_DEV_WC (_AT(pteval_t, 0x09) << 2) /* 1001 */
-#define L_PTE_MT_DEV_CACHED (_AT(pteval_t, 0x0b) << 2) /* 1011 */
-#define L_PTE_MT_MASK (_AT(pteval_t, 0x0f) << 2)
-
-#ifndef __ASSEMBLY__
-
/*
* The pgprot_* and protection_map entries will be fixed up in runtime
* to include the cachable and bufferable bits based on memory policy,
@@ -327,10 +196,10 @@
static inline pte_t *pmd_page_vaddr(pmd_t pmd)
{
- return __va(pmd_val(pmd) & PAGE_MASK);
+ return __va(pmd_val(pmd) & PHYS_MASK & (s32)PAGE_MASK);
}
-#define pmd_page(pmd) pfn_to_page(__phys_to_pfn(pmd_val(pmd)))
+#define pmd_page(pmd) pfn_to_page(__phys_to_pfn(pmd_val(pmd) & PHYS_MASK))
/* we don't need complex calculations here as the pmd is folded into the pgd */
#define pmd_addr_end(addr,end) (end)
@@ -351,7 +220,7 @@
#define pte_offset_map(pmd,addr) (__pte_map(pmd) + pte_index(addr))
#define pte_unmap(pte) __pte_unmap(pte)
-#define pte_pfn(pte) (pte_val(pte) >> PAGE_SHIFT)
+#define pte_pfn(pte) ((pte_val(pte) & PHYS_MASK) >> PAGE_SHIFT)
#define pfn_pte(pfn,prot) __pte(__pfn_to_phys(pfn) | pgprot_val(prot))
#define pte_page(pte) pfn_to_page(pte_pfn(pte))
diff --git a/arch/arm/include/asm/smp.h b/arch/arm/include/asm/smp.h
index e42d96a..0a17b62 100644
--- a/arch/arm/include/asm/smp.h
+++ b/arch/arm/include/asm/smp.h
@@ -33,6 +33,11 @@
asmlinkage void do_IPI(int ipinr, struct pt_regs *regs);
/*
+ * Called from C code, this handles an IPI.
+ */
+void handle_IPI(int ipinr, struct pt_regs *regs);
+
+/*
* Setup the set of possible CPUs (via set_cpu_possible)
*/
extern void smp_init_cpus(void);
@@ -66,6 +71,12 @@
extern void platform_smp_prepare_cpus(unsigned int);
/*
+ * Logical CPU mapping.
+ */
+extern int __cpu_logical_map[NR_CPUS];
+#define cpu_logical_map(cpu) __cpu_logical_map[cpu]
+
+/*
* Initial data for bringing up a secondary CPU.
*/
struct secondary_data {
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
index 832888d..ed6b049 100644
--- a/arch/arm/include/asm/system.h
+++ b/arch/arm/include/asm/system.h
@@ -62,13 +62,6 @@
#include <asm/outercache.h>
-#define __exception __attribute__((section(".exception.text")))
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
-#define __exception_irq_entry __irq_entry
-#else
-#define __exception_irq_entry __exception
-#endif
-
struct thread_info;
struct task_struct;
diff --git a/arch/arm/include/asm/tlbflush.h b/arch/arm/include/asm/tlbflush.h
index 8077145..02b2f82 100644
--- a/arch/arm/include/asm/tlbflush.h
+++ b/arch/arm/include/asm/tlbflush.h
@@ -471,7 +471,7 @@
* these operations. This is typically used when we are removing
* PMD entries.
*/
-static inline void flush_pmd_entry(pmd_t *pmd)
+static inline void flush_pmd_entry(void *pmd)
{
const unsigned int __tlb_flag = __cpu_tlb_flags;
@@ -487,7 +487,7 @@
dsb();
}
-static inline void clean_pmd_entry(pmd_t *pmd)
+static inline void clean_pmd_entry(void *pmd)
{
const unsigned int __tlb_flag = __cpu_tlb_flags;
diff --git a/arch/arm/include/asm/topology.h b/arch/arm/include/asm/topology.h
index accbd7c..a7e457e 100644
--- a/arch/arm/include/asm/topology.h
+++ b/arch/arm/include/asm/topology.h
@@ -1,6 +1,39 @@
#ifndef _ASM_ARM_TOPOLOGY_H
#define _ASM_ARM_TOPOLOGY_H
+#ifdef CONFIG_ARM_CPU_TOPOLOGY
+
+#include <linux/cpumask.h>
+
+struct cputopo_arm {
+ int thread_id;
+ int core_id;
+ int socket_id;
+ cpumask_t thread_sibling;
+ cpumask_t core_sibling;
+};
+
+extern struct cputopo_arm cpu_topology[NR_CPUS];
+
+#define topology_physical_package_id(cpu) (cpu_topology[cpu].socket_id)
+#define topology_core_id(cpu) (cpu_topology[cpu].core_id)
+#define topology_core_cpumask(cpu) (&cpu_topology[cpu].core_sibling)
+#define topology_thread_cpumask(cpu) (&cpu_topology[cpu].thread_sibling)
+
+#define mc_capable() (cpu_topology[0].socket_id != -1)
+#define smt_capable() (cpu_topology[0].thread_id != -1)
+
+void init_cpu_topology(void);
+void store_cpu_topology(unsigned int cpuid);
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu);
+
+#else
+
+static inline void init_cpu_topology(void) { }
+static inline void store_cpu_topology(unsigned int cpuid) { }
+
+#endif
+
#include <asm-generic/topology.h>
#endif /* _ASM_ARM_TOPOLOGY_H */
diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index f7887dc..68036ee 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -29,7 +29,7 @@
obj-$(CONFIG_ARTHUR) += arthur.o
obj-$(CONFIG_ISA_DMA) += dma-isa.o
obj-$(CONFIG_PCI) += bios32.o isa.o
-obj-$(CONFIG_PM_SLEEP) += sleep.o
+obj-$(CONFIG_ARM_CPU_SUSPEND) += sleep.o
obj-$(CONFIG_HAVE_SCHED_CLOCK) += sched_clock.o
obj-$(CONFIG_SMP) += smp.o smp_tlb.o
obj-$(CONFIG_HAVE_ARM_SCU) += smp_scu.o
@@ -66,6 +66,7 @@
obj-$(CONFIG_CPU_HAS_PMU) += pmu.o
obj-$(CONFIG_HW_PERF_EVENTS) += perf_event.o
AFLAGS_iwmmxt.o := -Wa,-mcpu=iwmmxt
+obj-$(CONFIG_ARM_CPU_TOPOLOGY) += topology.o
ifneq ($(CONFIG_ARCH_EBSA110),y)
obj-y += io.o
diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c
index 16baba2..1429d89 100644
--- a/arch/arm/kernel/asm-offsets.c
+++ b/arch/arm/kernel/asm-offsets.c
@@ -20,6 +20,7 @@
#include <asm/thread_info.h>
#include <asm/memory.h>
#include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
#include <linux/kbuild.h>
/*
@@ -92,6 +93,17 @@
DEFINE(S_OLD_R0, offsetof(struct pt_regs, ARM_ORIG_r0));
DEFINE(S_FRAME_SIZE, sizeof(struct pt_regs));
BLANK();
+#ifdef CONFIG_CACHE_L2X0
+ DEFINE(L2X0_R_PHY_BASE, offsetof(struct l2x0_regs, phy_base));
+ DEFINE(L2X0_R_AUX_CTRL, offsetof(struct l2x0_regs, aux_ctrl));
+ DEFINE(L2X0_R_TAG_LATENCY, offsetof(struct l2x0_regs, tag_latency));
+ DEFINE(L2X0_R_DATA_LATENCY, offsetof(struct l2x0_regs, data_latency));
+ DEFINE(L2X0_R_FILTER_START, offsetof(struct l2x0_regs, filter_start));
+ DEFINE(L2X0_R_FILTER_END, offsetof(struct l2x0_regs, filter_end));
+ DEFINE(L2X0_R_PREFETCH_CTRL, offsetof(struct l2x0_regs, prefetch_ctrl));
+ DEFINE(L2X0_R_PWR_CTRL, offsetof(struct l2x0_regs, pwr_ctrl));
+ BLANK();
+#endif
#ifdef CONFIG_CPU_HAS_ASID
DEFINE(MM_CONTEXT_ID, offsetof(struct mm_struct, context.id));
BLANK();
diff --git a/arch/arm/kernel/bios32.c b/arch/arm/kernel/bios32.c
index d6df359..c0d9203 100644
--- a/arch/arm/kernel/bios32.c
+++ b/arch/arm/kernel/bios32.c
@@ -412,6 +412,9 @@
printk(KERN_INFO "PCI: bus%d: Fast back to back transfers %sabled\n",
bus->number, (features & PCI_COMMAND_FAST_BACK) ? "en" : "dis");
}
+#ifdef CONFIG_HOTPLUG
+EXPORT_SYMBOL(pcibios_fixup_bus);
+#endif
/*
* Convert from Linux-centric to bus-centric addresses for bridge devices.
@@ -431,6 +434,7 @@
region->start = res->start - offset;
region->end = res->end - offset;
}
+EXPORT_SYMBOL(pcibios_resource_to_bus);
void __devinit
pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
@@ -447,12 +451,7 @@
res->start = region->start + offset;
res->end = region->end + offset;
}
-
-#ifdef CONFIG_HOTPLUG
-EXPORT_SYMBOL(pcibios_fixup_bus);
-EXPORT_SYMBOL(pcibios_resource_to_bus);
EXPORT_SYMBOL(pcibios_bus_to_resource);
-#endif
/*
* Swizzle the device pin each time we cross a bridge.
diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c
index d165001..4dd0eda 100644
--- a/arch/arm/kernel/ecard.c
+++ b/arch/arm/kernel/ecard.c
@@ -237,7 +237,7 @@
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
- src_pgd = pgd_offset(mm, EASI_BASE);
+ src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
dst_pgd = pgd_offset(mm, EASI_START);
memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
@@ -674,44 +674,37 @@
#define ecard_probeirqhw() (0)
#endif
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
{
- unsigned long address = 0;
+ void __iomem *address = NULL;
int slot = ec->slot_no;
if (ec->slot_no == 8)
- return IO_EC_MEMC8_BASE;
+ return ECARD_MEMC8_BASE;
ectcr &= ~(1 << slot);
switch (type) {
case ECARD_MEMC:
if (slot < 4)
- address = IO_EC_MEMC_BASE + (slot << 12);
+ address = ECARD_MEMC_BASE + (slot << 14);
break;
case ECARD_IOC:
if (slot < 4)
- address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+ address = ECARD_IOC_BASE + (slot << 14);
else
- address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+ address = ECARD_IOC4_BASE + ((slot - 4) << 14);
if (address)
- address += speed << 17;
+ address += speed << 19;
break;
-#ifdef IO_EC_EASI_BASE
case ECARD_EASI:
- address = IO_EC_EASI_BASE + (slot << 22);
+ address = ECARD_EASI_BASE + (slot << 24);
if (speed == ECARD_FAST)
ectcr |= 1 << slot;
break;
-#endif
+
default:
break;
}
@@ -990,6 +983,7 @@
ecard_t **ecp;
ecard_t *ec;
struct ex_ecid cid;
+ void __iomem *addr;
int i, rc;
ec = ecard_alloc_card(type, slot);
@@ -999,7 +993,7 @@
}
rc = -ENODEV;
- if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+ if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
goto nodev;
cid.r_zero = 1;
@@ -1019,7 +1013,7 @@
ec->cid.fiqmask = cid.r_fiqmask;
ec->cid.fiqoff = ecard_gets24(cid.r_fiqoff);
ec->fiqaddr =
- ec->irqaddr = (void __iomem *)ioaddr(ec->podaddr);
+ ec->irqaddr = addr;
if (ec->cid.is) {
ec->irqmask = ec->cid.irqmask;
@@ -1048,10 +1042,8 @@
set_irq_flags(ec->irq, IRQF_VALID);
}
-#ifdef IO_EC_MEMC8_BASE
if (slot == 8)
ec->irq = 11;
-#endif
#ifdef CONFIG_ARCH_RPC
/* On RiscPC, only first two slots have DMA capability */
if (slot < 2)
@@ -1097,9 +1089,7 @@
ecard_probe(slot, ECARD_IOC);
}
-#ifdef IO_EC_MEMC8_BASE
ecard_probe(8, ECARD_IOC);
-#endif
irqhw = ecard_probeirqhw();
diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S
index 742b610..239703d 100644
--- a/arch/arm/kernel/head.S
+++ b/arch/arm/kernel/head.S
@@ -21,6 +21,7 @@
#include <asm/memory.h>
#include <asm/thread_info.h>
#include <asm/system.h>
+#include <asm/pgtable.h>
#ifdef CONFIG_DEBUG_LL
#include <mach/debug-macro.S>
@@ -38,11 +39,14 @@
#error KERNEL_RAM_VADDR must start at 0xXXXX8000
#endif
+#define PG_DIR_SIZE 0x4000
+#define PMD_ORDER 2
+
.globl swapper_pg_dir
- .equ swapper_pg_dir, KERNEL_RAM_VADDR - 0x4000
+ .equ swapper_pg_dir, KERNEL_RAM_VADDR - PG_DIR_SIZE
.macro pgtbl, rd, phys
- add \rd, \phys, #TEXT_OFFSET - 0x4000
+ add \rd, \phys, #TEXT_OFFSET - PG_DIR_SIZE
.endm
#ifdef CONFIG_XIP_KERNEL
@@ -148,11 +152,11 @@
pgtbl r4, r8 @ page table address
/*
- * Clear the 16K level 1 swapper page table
+ * Clear the swapper page table
*/
mov r0, r4
mov r3, #0
- add r6, r0, #0x4000
+ add r6, r0, #PG_DIR_SIZE
1: str r3, [r0], #4
str r3, [r0], #4
str r3, [r0], #4
@@ -171,30 +175,30 @@
sub r0, r0, r3 @ virt->phys offset
add r5, r5, r0 @ phys __enable_mmu
add r6, r6, r0 @ phys __enable_mmu_end
- mov r5, r5, lsr #20
- mov r6, r6, lsr #20
+ mov r5, r5, lsr #SECTION_SHIFT
+ mov r6, r6, lsr #SECTION_SHIFT
-1: orr r3, r7, r5, lsl #20 @ flags + kernel base
- str r3, [r4, r5, lsl #2] @ identity mapping
- teq r5, r6
- addne r5, r5, #1 @ next section
- bne 1b
+1: orr r3, r7, r5, lsl #SECTION_SHIFT @ flags + kernel base
+ str r3, [r4, r5, lsl #PMD_ORDER] @ identity mapping
+ cmp r5, r6
+ addlo r5, r5, #1 @ next section
+ blo 1b
/*
* Now setup the pagetables for our kernel direct
* mapped region.
*/
mov r3, pc
- mov r3, r3, lsr #20
- orr r3, r7, r3, lsl #20
- add r0, r4, #(KERNEL_START & 0xff000000) >> 18
- str r3, [r0, #(KERNEL_START & 0x00f00000) >> 18]!
+ mov r3, r3, lsr #SECTION_SHIFT
+ orr r3, r7, r3, lsl #SECTION_SHIFT
+ add r0, r4, #(KERNEL_START & 0xff000000) >> (SECTION_SHIFT - PMD_ORDER)
+ str r3, [r0, #((KERNEL_START & 0x00f00000) >> SECTION_SHIFT) << PMD_ORDER]!
ldr r6, =(KERNEL_END - 1)
- add r0, r0, #4
- add r6, r4, r6, lsr #18
+ add r0, r0, #1 << PMD_ORDER
+ add r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
1: cmp r0, r6
- add r3, r3, #1 << 20
- strls r3, [r0], #4
+ add r3, r3, #1 << SECTION_SHIFT
+ strls r3, [r0], #1 << PMD_ORDER
bls 1b
#ifdef CONFIG_XIP_KERNEL
@@ -203,11 +207,11 @@
*/
add r3, r8, #TEXT_OFFSET
orr r3, r3, r7
- add r0, r4, #(KERNEL_RAM_VADDR & 0xff000000) >> 18
- str r3, [r0, #(KERNEL_RAM_VADDR & 0x00f00000) >> 18]!
+ add r0, r4, #(KERNEL_RAM_VADDR & 0xff000000) >> (SECTION_SHIFT - PMD_ORDER)
+ str r3, [r0, #(KERNEL_RAM_VADDR & 0x00f00000) >> (SECTION_SHIFT - PMD_ORDER)]!
ldr r6, =(_end - 1)
add r0, r0, #4
- add r6, r4, r6, lsr #18
+ add r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
1: cmp r0, r6
add r3, r3, #1 << 20
strls r3, [r0], #4
@@ -218,12 +222,12 @@
* Then map boot params address in r2 or
* the first 1MB of ram if boot params address is not specified.
*/
- mov r0, r2, lsr #20
- movs r0, r0, lsl #20
+ mov r0, r2, lsr #SECTION_SHIFT
+ movs r0, r0, lsl #SECTION_SHIFT
moveq r0, r8
sub r3, r0, r8
add r3, r3, #PAGE_OFFSET
- add r3, r4, r3, lsr #18
+ add r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER)
orr r6, r7, r0
str r6, [r3]
@@ -236,21 +240,21 @@
*/
addruart r7, r3
- mov r3, r3, lsr #20
- mov r3, r3, lsl #2
+ mov r3, r3, lsr #SECTION_SHIFT
+ mov r3, r3, lsl #PMD_ORDER
add r0, r4, r3
rsb r3, r3, #0x4000 @ PTRS_PER_PGD*sizeof(long)
cmp r3, #0x0800 @ limit to 512MB
movhi r3, #0x0800
add r6, r0, r3
- mov r3, r7, lsr #20
+ mov r3, r7, lsr #SECTION_SHIFT
ldr r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags
- orr r3, r7, r3, lsl #20
+ orr r3, r7, r3, lsl #SECTION_SHIFT
1: str r3, [r0], #4
- add r3, r3, #1 << 20
- teq r0, r6
- bne 1b
+ add r3, r3, #1 << SECTION_SHIFT
+ cmp r0, r6
+ blo 1b
#else /* CONFIG_DEBUG_ICEDCC */
/* we don't need any serial debugging mappings for ICEDCC */
@@ -262,7 +266,7 @@
* If we're using the NetWinder or CATS, we also need to map
* in the 16550-type serial port for the debug messages
*/
- add r0, r4, #0xff000000 >> 18
+ add r0, r4, #0xff000000 >> (SECTION_SHIFT - PMD_ORDER)
orr r3, r7, #0x7c000000
str r3, [r0]
#endif
@@ -272,10 +276,10 @@
* Similar reasons here - for debug. This is
* only for Acorn RiscPC architectures.
*/
- add r0, r4, #0x02000000 >> 18
+ add r0, r4, #0x02000000 >> (SECTION_SHIFT - PMD_ORDER)
orr r3, r7, #0x02000000
str r3, [r0]
- add r0, r4, #0xd8000000 >> 18
+ add r0, r4, #0xd8000000 >> (SECTION_SHIFT - PMD_ORDER)
str r3, [r0]
#endif
#endif
@@ -488,13 +492,8 @@
add r5, r5, r3 @ adjust table end address
add r7, r7, r3 @ adjust __pv_phys_offset address
str r8, [r7] @ save computed PHYS_OFFSET to __pv_phys_offset
-#ifndef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
mov r6, r3, lsr #24 @ constant for add/sub instructions
teq r3, r6, lsl #24 @ must be 16MiB aligned
-#else
- mov r6, r3, lsr #16 @ constant for add/sub instructions
- teq r3, r6, lsl #16 @ must be 64kiB aligned
-#endif
THUMB( it ne @ cross section branch )
bne __error
str r6, [r7, #4] @ save to __pv_offset
@@ -510,20 +509,8 @@
.text
__fixup_a_pv_table:
#ifdef CONFIG_THUMB2_KERNEL
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- lsls r0, r6, #24
- lsr r6, #8
- beq 1f
- clz r7, r0
- lsr r0, #24
- lsl r0, r7
- bic r0, 0x0080
- lsrs r7, #1
- orrcs r0, #0x0080
- orr r0, r0, r7, lsl #12
-#endif
-1: lsls r6, #24
- beq 4f
+ lsls r6, #24
+ beq 2f
clz r7, r6
lsr r6, #24
lsl r6, r7
@@ -532,43 +519,25 @@
orrcs r6, #0x0080
orr r6, r6, r7, lsl #12
orr r6, #0x4000
- b 4f
-2: @ at this point the C flag is always clear
- add r7, r3
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- ldrh ip, [r7]
- tst ip, 0x0400 @ the i bit tells us LS or MS byte
- beq 3f
- cmp r0, #0 @ set C flag, and ...
- biceq ip, 0x0400 @ immediate zero value has a special encoding
- streqh ip, [r7] @ that requires the i bit cleared
-#endif
-3: ldrh ip, [r7, #2]
+ b 2f
+1: add r7, r3
+ ldrh ip, [r7, #2]
and ip, 0x8f00
- orrcc ip, r6 @ mask in offset bits 31-24
- orrcs ip, r0 @ mask in offset bits 23-16
+ orr ip, r6 @ mask in offset bits 31-24
strh ip, [r7, #2]
-4: cmp r4, r5
+2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
- bcc 2b
+ bcc 1b
bx lr
#else
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
- and r0, r6, #255 @ offset bits 23-16
- mov r6, r6, lsr #8 @ offset bits 31-24
-#else
- mov r0, #0 @ just in case...
-#endif
- b 3f
-2: ldr ip, [r7, r3]
+ b 2f
+1: ldr ip, [r7, r3]
bic ip, ip, #0x000000ff
- tst ip, #0x400 @ rotate shift tells us LS or MS byte
- orrne ip, ip, r6 @ mask in offset bits 31-24
- orreq ip, ip, r0 @ mask in offset bits 23-16
+ orr ip, ip, r6 @ mask in offset bits 31-24
str ip, [r7, r3]
-3: cmp r4, r5
+2: cmp r4, r5
ldrcc r7, [r4], #4 @ use branch for delay slot
- bcc 2b
+ bcc 1b
mov pc, lr
#endif
ENDPROC(__fixup_a_pv_table)
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index de3dcab..53919b2 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -35,8 +35,8 @@
#include <linux/list.h>
#include <linux/kallsyms.h>
#include <linux/proc_fs.h>
-#include <linux/ftrace.h>
+#include <asm/exception.h>
#include <asm/system.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
diff --git a/arch/arm/kernel/module.c b/arch/arm/kernel/module.c
index cc2020c..1e9be5d 100644
--- a/arch/arm/kernel/module.c
+++ b/arch/arm/kernel/module.c
@@ -33,7 +33,7 @@
* recompiling the whole kernel when CONFIG_XIP_KERNEL is turned on/off.
*/
#undef MODULES_VADDR
-#define MODULES_VADDR (((unsigned long)_etext + ~PGDIR_MASK) & PGDIR_MASK)
+#define MODULES_VADDR (((unsigned long)_etext + ~PMD_MASK) & PMD_MASK)
#endif
#ifdef CONFIG_MMU
diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c
index d88ff02..35417d0 100644
--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -16,7 +16,6 @@
#include <linux/cache.h>
#include <linux/profile.h>
#include <linux/errno.h>
-#include <linux/ftrace.h>
#include <linux/mm.h>
#include <linux/err.h>
#include <linux/cpu.h>
@@ -31,6 +30,8 @@
#include <asm/cacheflush.h>
#include <asm/cpu.h>
#include <asm/cputype.h>
+#include <asm/exception.h>
+#include <asm/topology.h>
#include <asm/mmu_context.h>
#include <asm/pgtable.h>
#include <asm/pgalloc.h>
@@ -39,6 +40,7 @@
#include <asm/tlbflush.h>
#include <asm/ptrace.h>
#include <asm/localtimer.h>
+#include <asm/smp_plat.h>
/*
* as from 2.5, kernels no longer have an init_tasks structure
@@ -259,6 +261,20 @@
}
#endif /* CONFIG_HOTPLUG_CPU */
+int __cpu_logical_map[NR_CPUS];
+
+void __init smp_setup_processor_id(void)
+{
+ int i;
+ u32 cpu = is_smp() ? read_cpuid_mpidr() & 0xff : 0;
+
+ cpu_logical_map(0) = cpu;
+ for (i = 1; i < NR_CPUS; ++i)
+ cpu_logical_map(i) = i == cpu ? 0 : i;
+
+ printk(KERN_INFO "Booting Linux on physical CPU %d\n", cpu);
+}
+
/*
* Called by both boot and secondaries to move global data into
* per-processor storage.
@@ -268,6 +284,8 @@
struct cpuinfo_arm *cpu_info = &per_cpu(cpu_data, cpuid);
cpu_info->loops_per_jiffy = loops_per_jiffy;
+
+ store_cpu_topology(cpuid);
}
/*
@@ -358,6 +376,8 @@
{
unsigned int ncores = num_possible_cpus();
+ init_cpu_topology();
+
smp_store_cpu_info(smp_processor_id());
/*
@@ -460,6 +480,11 @@
#ifdef CONFIG_LOCAL_TIMERS
asmlinkage void __exception_irq_entry do_local_timer(struct pt_regs *regs)
{
+ handle_local_timer(regs);
+}
+
+void handle_local_timer(struct pt_regs *regs)
+{
struct pt_regs *old_regs = set_irq_regs(regs);
int cpu = smp_processor_id();
@@ -567,6 +592,11 @@
*/
asmlinkage void __exception_irq_entry do_IPI(int ipinr, struct pt_regs *regs)
{
+ handle_IPI(ipinr, regs);
+}
+
+void handle_IPI(int ipinr, struct pt_regs *regs)
+{
unsigned int cpu = smp_processor_id();
struct pt_regs *old_regs = set_irq_regs(regs);
diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c
index 7fcddb7..8f5dd79 100644
--- a/arch/arm/kernel/smp_scu.c
+++ b/arch/arm/kernel/smp_scu.c
@@ -34,7 +34,7 @@
/*
* Enable the SCU
*/
-void __init scu_enable(void __iomem *scu_base)
+void scu_enable(void __iomem *scu_base)
{
u32 scu_ctrl;
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index cb634c3..5a54b95 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -39,13 +39,11 @@
*/
static struct sys_timer *system_timer;
-#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE)
+#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE) || \
+ defined(CONFIG_NVRAM) || defined(CONFIG_NVRAM_MODULE)
/* this needs a better home */
DEFINE_SPINLOCK(rtc_lock);
-
-#ifdef CONFIG_RTC_DRV_CMOS_MODULE
EXPORT_SYMBOL(rtc_lock);
-#endif
#endif /* pc-style 'CMOS' RTC support */
/* change this if you have some constant time drift */
diff --git a/arch/arm/kernel/topology.c b/arch/arm/kernel/topology.c
new file mode 100644
index 0000000..1040c00
--- /dev/null
+++ b/arch/arm/kernel/topology.c
@@ -0,0 +1,148 @@
+/*
+ * arch/arm/kernel/topology.c
+ *
+ * Copyright (C) 2011 Linaro Limited.
+ * Written by: Vincent Guittot
+ *
+ * based on arch/sh/kernel/topology.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/cpu.h>
+#include <linux/cpumask.h>
+#include <linux/init.h>
+#include <linux/percpu.h>
+#include <linux/node.h>
+#include <linux/nodemask.h>
+#include <linux/sched.h>
+
+#include <asm/cputype.h>
+#include <asm/topology.h>
+
+#define MPIDR_SMP_BITMASK (0x3 << 30)
+#define MPIDR_SMP_VALUE (0x2 << 30)
+
+#define MPIDR_MT_BITMASK (0x1 << 24)
+
+/*
+ * These masks reflect the current use of the affinity levels.
+ * The affinity level can be up to 16 bits according to ARM ARM
+ */
+
+#define MPIDR_LEVEL0_MASK 0x3
+#define MPIDR_LEVEL0_SHIFT 0
+
+#define MPIDR_LEVEL1_MASK 0xF
+#define MPIDR_LEVEL1_SHIFT 8
+
+#define MPIDR_LEVEL2_MASK 0xFF
+#define MPIDR_LEVEL2_SHIFT 16
+
+struct cputopo_arm cpu_topology[NR_CPUS];
+
+const struct cpumask *cpu_coregroup_mask(unsigned int cpu)
+{
+ return &cpu_topology[cpu].core_sibling;
+}
+
+/*
+ * store_cpu_topology is called at boot when only one cpu is running
+ * and with the mutex cpu_hotplug.lock locked, when several cpus have booted,
+ * which prevents simultaneous write access to cpu_topology array
+ */
+void store_cpu_topology(unsigned int cpuid)
+{
+ struct cputopo_arm *cpuid_topo = &cpu_topology[cpuid];
+ unsigned int mpidr;
+ unsigned int cpu;
+
+ /* If the cpu topology has been already set, just return */
+ if (cpuid_topo->core_id != -1)
+ return;
+
+ mpidr = read_cpuid_mpidr();
+
+ /* create cpu topology mapping */
+ if ((mpidr & MPIDR_SMP_BITMASK) == MPIDR_SMP_VALUE) {
+ /*
+ * This is a multiprocessor system
+ * multiprocessor format & multiprocessor mode field are set
+ */
+
+ if (mpidr & MPIDR_MT_BITMASK) {
+ /* core performance interdependency */
+ cpuid_topo->thread_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+ & MPIDR_LEVEL0_MASK;
+ cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+ & MPIDR_LEVEL1_MASK;
+ cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL2_SHIFT)
+ & MPIDR_LEVEL2_MASK;
+ } else {
+ /* largely independent cores */
+ cpuid_topo->thread_id = -1;
+ cpuid_topo->core_id = (mpidr >> MPIDR_LEVEL0_SHIFT)
+ & MPIDR_LEVEL0_MASK;
+ cpuid_topo->socket_id = (mpidr >> MPIDR_LEVEL1_SHIFT)
+ & MPIDR_LEVEL1_MASK;
+ }
+ } else {
+ /*
+ * This is an uniprocessor system
+ * we are in multiprocessor format but uniprocessor system
+ * or in the old uniprocessor format
+ */
+ cpuid_topo->thread_id = -1;
+ cpuid_topo->core_id = 0;
+ cpuid_topo->socket_id = -1;
+ }
+
+ /* update core and thread sibling masks */
+ for_each_possible_cpu(cpu) {
+ struct cputopo_arm *cpu_topo = &cpu_topology[cpu];
+
+ if (cpuid_topo->socket_id == cpu_topo->socket_id) {
+ cpumask_set_cpu(cpuid, &cpu_topo->core_sibling);
+ if (cpu != cpuid)
+ cpumask_set_cpu(cpu,
+ &cpuid_topo->core_sibling);
+
+ if (cpuid_topo->core_id == cpu_topo->core_id) {
+ cpumask_set_cpu(cpuid,
+ &cpu_topo->thread_sibling);
+ if (cpu != cpuid)
+ cpumask_set_cpu(cpu,
+ &cpuid_topo->thread_sibling);
+ }
+ }
+ }
+ smp_wmb();
+
+ printk(KERN_INFO "CPU%u: thread %d, cpu %d, socket %d, mpidr %x\n",
+ cpuid, cpu_topology[cpuid].thread_id,
+ cpu_topology[cpuid].core_id,
+ cpu_topology[cpuid].socket_id, mpidr);
+}
+
+/*
+ * init_cpu_topology is called at boot when only one cpu is running
+ * which prevent simultaneous write access to cpu_topology array
+ */
+void init_cpu_topology(void)
+{
+ unsigned int cpu;
+
+ /* init core mask */
+ for_each_possible_cpu(cpu) {
+ struct cputopo_arm *cpu_topo = &(cpu_topology[cpu]);
+
+ cpu_topo->thread_id = -1;
+ cpu_topo->core_id = -1;
+ cpu_topo->socket_id = -1;
+ cpumask_clear(&cpu_topo->core_sibling);
+ cpumask_clear(&cpu_topo->thread_sibling);
+ }
+ smp_wmb();
+}
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index bc9f9da..2103825 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -27,6 +27,7 @@
#include <linux/atomic.h>
#include <asm/cacheflush.h>
+#include <asm/exception.h>
#include <asm/system.h>
#include <asm/unistd.h>
#include <asm/traps.h>
diff --git a/arch/arm/lib/uaccess_with_memcpy.c b/arch/arm/lib/uaccess_with_memcpy.c
index 8b9b136..025f742 100644
--- a/arch/arm/lib/uaccess_with_memcpy.c
+++ b/arch/arm/lib/uaccess_with_memcpy.c
@@ -17,6 +17,7 @@
#include <linux/sched.h>
#include <linux/hardirq.h> /* for in_atomic() */
#include <linux/gfp.h>
+#include <linux/highmem.h>
#include <asm/current.h>
#include <asm/page.h>
diff --git a/arch/arm/mach-ebsa110/include/mach/io.h b/arch/arm/mach-ebsa110/include/mach/io.h
index f68daa63..44679db 100644
--- a/arch/arm/mach-ebsa110/include/mach/io.h
+++ b/arch/arm/mach-ebsa110/include/mach/io.h
@@ -13,8 +13,6 @@
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
u8 __inb8(unsigned int port);
void __outb8(u8 val, unsigned int port);
diff --git a/arch/arm/mach-exynos4/Kconfig b/arch/arm/mach-exynos4/Kconfig
index 0c77ab9..fc1f92d 100644
--- a/arch/arm/mach-exynos4/Kconfig
+++ b/arch/arm/mach-exynos4/Kconfig
@@ -12,6 +12,7 @@
config CPU_EXYNOS4210
bool
select S3C_PL330_DMA
+ select ARM_CPU_SUSPEND if PM
help
Enable EXYNOS4210 CPU support
diff --git a/arch/arm/mach-exynos4/platsmp.c b/arch/arm/mach-exynos4/platsmp.c
index df6ef1b..0c90896 100644
--- a/arch/arm/mach-exynos4/platsmp.c
+++ b/arch/arm/mach-exynos4/platsmp.c
@@ -193,12 +193,10 @@
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
- if (ncores > NR_CPUS) {
- printk(KERN_WARNING
- "EXYNOS4: no. of cores (%d) greater than configured "
- "maximum of %d - clipping\n",
- ncores, NR_CPUS);
- ncores = NR_CPUS;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-footbridge/include/mach/io.h b/arch/arm/mach-footbridge/include/mach/io.h
index 32e4cc3..15a7039 100644
--- a/arch/arm/mach-footbridge/include/mach/io.h
+++ b/arch/arm/mach-footbridge/include/mach/io.h
@@ -23,8 +23,6 @@
#define PCIO_SIZE 0x00100000
#define PCIO_BASE MMU_IO(0xff000000, 0x7c000000)
-#define IO_SPACE_LIMIT 0xffff
-
/*
* Translation of various region addresses to virtual addresses
*/
diff --git a/arch/arm/mach-integrator/include/mach/io.h b/arch/arm/mach-integrator/include/mach/io.h
index f21bb54..37beed3 100644
--- a/arch/arm/mach-integrator/include/mach/io.h
+++ b/arch/arm/mach-integrator/include/mach/io.h
@@ -20,8 +20,6 @@
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
/*
* WARNING: this has to mirror definitions in platform.h
*/
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index 57b5410..ffb9d6a 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -17,8 +17,6 @@
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0x0000ffff
-
extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c
index b7a8496..d1e4cc8 100644
--- a/arch/arm/mach-msm/board-msm7x30.c
+++ b/arch/arm/mach-msm/board-msm7x30.c
@@ -24,6 +24,7 @@
#include <linux/smsc911x.h>
#include <linux/usb/msm_hsusb.h>
#include <linux/clkdev.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -42,6 +43,21 @@
extern struct sys_timer msm_timer;
+static void __init msm7x30_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM && tag->u.mem.start == 0x200000) {
+ tag->u.mem.start = 0;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm7x30_reserve(void)
+{
+ memblock_remove(0x0, SZ_2M);
+}
+
static int hsusb_phy_init_seq[] = {
0x30, 0x32, /* Enable and set Pre-Emphasis Depth to 20% */
0x02, 0x36, /* Disable CDR Auto Reset feature */
@@ -107,6 +123,8 @@
MACHINE_START(MSM7X30_SURF, "QCT MSM7X30 SURF")
.boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
@@ -115,6 +133,8 @@
MACHINE_START(MSM7X30_FFA, "QCT MSM7X30 FFA")
.boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
@@ -123,6 +143,8 @@
MACHINE_START(MSM7X30_FLUID, "QCT MSM7X30 FLUID")
.boot_params = PLAT_PHYS_OFFSET + 0x100,
+ .fixup = msm7x30_fixup,
+ .reserve = msm7x30_reserve,
.map_io = msm7x30_map_io,
.init_irq = msm7x30_init_irq,
.init_machine = msm7x30_init,
diff --git a/arch/arm/mach-msm/board-msm8960.c b/arch/arm/mach-msm/board-msm8960.c
index 35c7cee..b04468e 100644
--- a/arch/arm/mach-msm/board-msm8960.c
+++ b/arch/arm/mach-msm/board-msm8960.c
@@ -20,16 +20,34 @@
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/clkdev.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
+#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include "devices.h"
+static void __init msm8960_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM &&
+ tag->u.mem.start == 0x40200000) {
+ tag->u.mem.start = 0x40000000;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm8960_reserve(void)
+{
+ memblock_remove(0x40000000, SZ_2M);
+}
+
static void __init msm8960_map_io(void)
{
msm_map_msm8960_io();
@@ -76,6 +94,8 @@
}
MACHINE_START(MSM8960_SIM, "QCT MSM8960 SIMULATOR")
+ .fixup = msm8960_fixup,
+ .reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
@@ -83,6 +103,8 @@
MACHINE_END
MACHINE_START(MSM8960_RUMI3, "QCT MSM8960 RUMI3")
+ .fixup = msm8960_fixup,
+ .reserve = msm8960_reserve,
.map_io = msm8960_map_io,
.init_irq = msm8960_init_irq,
.timer = &msm_timer,
diff --git a/arch/arm/mach-msm/board-msm8x60.c b/arch/arm/mach-msm/board-msm8x60.c
index 1163b6f..9221f54 100644
--- a/arch/arm/mach-msm/board-msm8x60.c
+++ b/arch/arm/mach-msm/board-msm8x60.c
@@ -20,14 +20,31 @@
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/memblock.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
+#include <asm/setup.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
+static void __init msm8x60_fixup(struct machine_desc *desc, struct tag *tag,
+ char **cmdline, struct meminfo *mi)
+{
+ for (; tag->hdr.size; tag = tag_next(tag))
+ if (tag->hdr.tag == ATAG_MEM &&
+ tag->u.mem.start == 0x40200000) {
+ tag->u.mem.start = 0x40000000;
+ tag->u.mem.size += SZ_2M;
+ }
+}
+
+static void __init msm8x60_reserve(void)
+{
+ memblock_remove(0x40000000, SZ_2M);
+}
static void __init msm8x60_map_io(void)
{
@@ -65,6 +82,8 @@
}
MACHINE_START(MSM8X60_RUMI3, "QCT MSM8X60 RUMI3")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
@@ -72,6 +91,8 @@
MACHINE_END
MACHINE_START(MSM8X60_SURF, "QCT MSM8X60 SURF")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
@@ -79,6 +100,8 @@
MACHINE_END
MACHINE_START(MSM8X60_SIM, "QCT MSM8X60 SIMULATOR")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
@@ -86,6 +109,8 @@
MACHINE_END
MACHINE_START(MSM8X60_FFA, "QCT MSM8X60 FFA")
+ .fixup = msm8x60_fixup,
+ .reserve = msm8x60_reserve,
.map_io = msm8x60_map_io,
.init_irq = msm8x60_init_irq,
.init_machine = msm8x60_init,
diff --git a/arch/arm/mach-msm/include/mach/memory.h b/arch/arm/mach-msm/include/mach/memory.h
index f2f8d29..58d5e7e 100644
--- a/arch/arm/mach-msm/include/mach/memory.h
+++ b/arch/arm/mach-msm/include/mach/memory.h
@@ -22,11 +22,11 @@
#elif defined(CONFIG_ARCH_QSD8X50)
#define PLAT_PHYS_OFFSET UL(0x20000000)
#elif defined(CONFIG_ARCH_MSM7X30)
-#define PLAT_PHYS_OFFSET UL(0x00200000)
+#define PLAT_PHYS_OFFSET UL(0x00000000)
#elif defined(CONFIG_ARCH_MSM8X60)
-#define PLAT_PHYS_OFFSET UL(0x40200000)
+#define PLAT_PHYS_OFFSET UL(0x40000000)
#elif defined(CONFIG_ARCH_MSM8960)
-#define PLAT_PHYS_OFFSET UL(0x40200000)
+#define PLAT_PHYS_OFFSET UL(0x40000000)
#else
#define PLAT_PHYS_OFFSET UL(0x10000000)
#endif
diff --git a/arch/arm/mach-msm/platsmp.c b/arch/arm/mach-msm/platsmp.c
index 1a1af9e..7276595 100644
--- a/arch/arm/mach-msm/platsmp.c
+++ b/arch/arm/mach-msm/platsmp.c
@@ -156,6 +156,12 @@
{
unsigned int i, ncores = get_core_count();
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
+ }
+
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 57b66d5..89bfb49 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -36,6 +36,7 @@
select ARM_L1_CACHE_SHIFT_6 if !ARCH_OMAP4
select ARCH_HAS_OPP
select PM_OPP if PM
+ select ARM_CPU_SUSPEND if PM
config ARCH_OMAP4
bool "TI OMAP4"
@@ -50,6 +51,7 @@
select ARCH_HAS_OPP
select PM_OPP if PM
select USB_ARCH_HAS_EHCI
+ select ARM_CPU_SUSPEND if PM
comment "OMAP Core Type"
depends on ARCH_OMAP2
diff --git a/arch/arm/mach-omap2/omap-smp.c b/arch/arm/mach-omap2/omap-smp.c
index ce65e93..889464d 100644
--- a/arch/arm/mach-omap2/omap-smp.c
+++ b/arch/arm/mach-omap2/omap-smp.c
@@ -109,12 +109,10 @@
ncores = scu_get_core_count(scu_base);
/* sanity check */
- if (ncores > NR_CPUS) {
- printk(KERN_WARNING
- "OMAP4: no. of cores (%d) greater than configured "
- "maximum of %d - clipping\n",
- ncores, NR_CPUS);
- ncores = NR_CPUS;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index b09e848..ca60757 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -19,6 +19,8 @@
#include <linux/io.h>
#include <linux/irq.h>
+#include <asm/exception.h>
+
#include <mach/hardware.h>
#include <mach/irqs.h>
#include <mach/gpio.h>
diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c
index 4ae943b..e83c654 100644
--- a/arch/arm/mach-realview/platsmp.c
+++ b/arch/arm/mach-realview/platsmp.c
@@ -52,12 +52,10 @@
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
- if (ncores > NR_CPUS) {
- printk(KERN_WARNING
- "Realview: no. of cores (%d) greater than configured "
- "maximum of %d - clipping\n",
- ncores, NR_CPUS);
- ncores = NR_CPUS;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-rpc/include/mach/hardware.h b/arch/arm/mach-rpc/include/mach/hardware.h
index dde6b3c..050d63c 100644
--- a/arch/arm/mach-rpc/include/mach/hardware.h
+++ b/arch/arm/mach-rpc/include/mach/hardware.h
@@ -36,7 +36,7 @@
#define EASI_SIZE 0x08000000 /* EASI I/O */
#define EASI_START 0x08000000
-#define EASI_BASE 0xe5000000
+#define EASI_BASE IOMEM(0xe5000000)
#define IO_START 0x03000000 /* I/O */
#define IO_SIZE 0x01000000
@@ -51,21 +51,20 @@
/*
* IO Addresses
*/
-#define VIDC_BASE IOMEM(0xe0400000)
-#define EXPMASK_BASE 0xe0360000
-#define IOMD_BASE IOMEM(0xe0200000)
-#define IOC_BASE IOMEM(0xe0200000)
-#define PCIO_BASE IOMEM(0xe0010000)
-#define FLOPPYDMA_BASE IOMEM(0xe002a000)
+#define ECARD_EASI_BASE (EASI_BASE)
+#define VIDC_BASE (IO_BASE + 0x00400000)
+#define EXPMASK_BASE (IO_BASE + 0x00360000)
+#define ECARD_IOC4_BASE (IO_BASE + 0x00270000)
+#define ECARD_IOC_BASE (IO_BASE + 0x00240000)
+#define IOMD_BASE (IO_BASE + 0x00200000)
+#define IOC_BASE (IO_BASE + 0x00200000)
+#define ECARD_MEMC8_BASE (IO_BASE + 0x0002b000)
+#define FLOPPYDMA_BASE (IO_BASE + 0x0002a000)
+#define PCIO_BASE (IO_BASE + 0x00010000)
+#define ECARD_MEMC_BASE (IO_BASE + 0x00000000)
#define vidc_writel(val) __raw_writel(val, VIDC_BASE)
-#define IO_EC_EASI_BASE 0x81400000
-#define IO_EC_IOC4_BASE 0x8009c000
-#define IO_EC_IOC_BASE 0x80090000
-#define IO_EC_MEMC8_BASE 0x8000ac00
-#define IO_EC_MEMC_BASE 0x80000000
-
#define NETSLOT_BASE 0x0302b000
#define NETSLOT_SIZE 0x00001000
diff --git a/arch/arm/mach-rpc/include/mach/io.h b/arch/arm/mach-rpc/include/mach/io.h
index 20da7f4..695f4ed 100644
--- a/arch/arm/mach-rpc/include/mach/io.h
+++ b/arch/arm/mach-rpc/include/mach/io.h
@@ -15,195 +15,18 @@
#include <mach/hardware.h>
-#define IO_SPACE_LIMIT 0xffffffff
+#define IO_SPACE_LIMIT 0xffff
/*
- * We use two different types of addressing - PC style addresses, and ARM
- * addresses. PC style accesses the PC hardware with the normal PC IO
- * addresses, eg 0x3f8 for serial#1. ARM addresses are 0x80000000+
- * and are translated to the start of IO. Note that all addresses are
- * shifted left!
- */
-#define __PORT_PCIO(x) (!((x) & 0x80000000))
-
-/*
- * Dynamic IO functions.
- */
-static inline void __outb (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "strb %1, [%0, %2, lsl #2] @ outb"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outw (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outw"
- : "=&r" (temp)
- : "r" (value|value<<16), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-static inline void __outl (unsigned int value, unsigned int port)
-{
- unsigned long temp;
- __asm__ __volatile__(
- "tst %2, #0x80000000\n\t"
- "mov %0, %4\n\t"
- "addeq %0, %0, %3\n\t"
- "str %1, [%0, %2, lsl #2] @ outl"
- : "=&r" (temp)
- : "r" (value), "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE)
- : "cc");
-}
-
-#define DECLARE_DYN_IN(sz,fnsuffix,instr) \
-static inline unsigned sz __in##fnsuffix (unsigned int port) \
-{ \
- unsigned long temp, value; \
- __asm__ __volatile__( \
- "tst %2, #0x80000000\n\t" \
- "mov %0, %4\n\t" \
- "addeq %0, %0, %3\n\t" \
- "ldr" instr " %1, [%0, %2, lsl #2] @ in" #fnsuffix \
- : "=&r" (temp), "=r" (value) \
- : "r" (port), "Ir" (PCIO_BASE - IO_BASE), "Ir" (IO_BASE) \
- : "cc"); \
- return (unsigned sz)value; \
-}
-
-static inline void __iomem *__deprecated __ioaddr(unsigned int port)
-{
- void __iomem *ret;
- if (__PORT_PCIO(port))
- ret = PCIO_BASE;
- else
- ret = IO_BASE;
- return ret + (port << 2);
-}
-
-#define DECLARE_IO(sz,fnsuffix,instr) \
- DECLARE_DYN_IN(sz,fnsuffix,instr)
-
-DECLARE_IO(char,b,"b")
-DECLARE_IO(short,w,"")
-DECLARE_IO(int,l,"")
-
-#undef DECLARE_IO
-#undef DECLARE_DYN_IN
-
-/*
- * Constant address IO functions
+ * We need PC style IO addressing for:
+ * - floppy (at 0x3f2,0x3f4,0x3f5,0x3f7)
+ * - parport (at 0x278-0x27a, 0x27b-0x27f, 0x778-0x77a)
+ * - 8250 serial (only for compile)
*
- * These have to be macros for the 'J' constraint to work -
- * +/-4096 immediate operand.
+ * These peripherals are found in an area of MMIO which looks very much
+ * like an ISA bus, but with registers at the low byte of each word.
*/
-#define __outbc(value,port) \
-({ \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "strb %0, [%1, %2] @ outbc" \
- : : "r" (value), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inbc(port) \
-({ \
- unsigned char result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldrb %0, [%1, %2] @ inbc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define __outwc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outwc" \
- : : "r" (__v|__v<<16), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inwc(port) \
-({ \
- unsigned short result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inwc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result & 0xffff; \
-})
-
-#define __outlc(value,port) \
-({ \
- unsigned long __v = value; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "str %0, [%1, %2] @ outlc" \
- : : "r" (__v), "r" (IO_BASE), "r" ((port) << 2)); \
-})
-
-#define __inlc(port) \
-({ \
- unsigned long result; \
- if (__PORT_PCIO((port))) \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (PCIO_BASE), "Jr" ((port) << 2)); \
- else \
- __asm__ __volatile__( \
- "ldr %0, [%1, %2] @ inlc" \
- : "=r" (result) : "r" (IO_BASE), "r" ((port) << 2)); \
- result; \
-})
-
-#define inb(p) (__builtin_constant_p((p)) ? __inbc(p) : __inb(p))
-#define inw(p) (__builtin_constant_p((p)) ? __inwc(p) : __inw(p))
-#define inl(p) (__builtin_constant_p((p)) ? __inlc(p) : __inl(p))
-#define outb(v,p) (__builtin_constant_p((p)) ? __outbc(v,p) : __outb(v,p))
-#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
-#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
-
-/* the following macro is deprecated */
-#define ioaddr(port) ((unsigned long)__ioaddr((port)))
-
-#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
-#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
-
-#define outsb(p,d,l) __raw_writesb(__ioaddr(p),d,l)
-#define outsw(p,d,l) __raw_writesw(__ioaddr(p),d,l)
+#define __io(a) (PCIO_BASE + ((a) << 2))
/*
* 1:1 mapping for ioremapped regions.
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index 580b3c7..1e0e60d 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -74,7 +74,7 @@
.length = IO_SIZE ,
.type = MT_DEVICE
}, { /* EASI space */
- .virtual = EASI_BASE,
+ .virtual = (unsigned long)EASI_BASE,
.pfn = __phys_to_pfn(EASI_START),
.length = EASI_SIZE,
.type = MT_DEVICE
diff --git a/arch/arm/mach-s3c2410/include/mach/io.h b/arch/arm/mach-s3c2410/include/mach/io.h
index 9813dbf..118749f 100644
--- a/arch/arm/mach-s3c2410/include/mach/io.h
+++ b/arch/arm/mach-s3c2410/include/mach/io.h
@@ -199,8 +199,6 @@
#define outw(v,p) (__builtin_constant_p((p)) ? __outwc(v,p) : __outw(v,p))
#define outl(v,p) (__builtin_constant_p((p)) ? __outlc(v,p) : __outl(v,p))
#define __ioaddr(p) (__builtin_constant_p((p)) ? __ioaddr(p) : __ioaddrc(p))
-/* the following macro is deprecated */
-#define ioaddr(port) __ioaddr((port))
#define insb(p,d,l) __raw_readsb(__ioaddr(p),d,l)
#define insw(p,d,l) __raw_readsw(__ioaddr(p),d,l)
diff --git a/arch/arm/mach-sa1100/include/mach/io.h b/arch/arm/mach-sa1100/include/mach/io.h
index d8b43f3..dfc27ff 100644
--- a/arch/arm/mach-sa1100/include/mach/io.h
+++ b/arch/arm/mach-sa1100/include/mach/io.h
@@ -10,11 +10,9 @@
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffffffff
-
/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
+ * __io() is required to be an equivalent mapping to __mem_pci() for
+ * SOC_COMMON to work.
*/
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
diff --git a/arch/arm/mach-shmobile/platsmp.c b/arch/arm/mach-shmobile/platsmp.c
index 66f9806..e4e485f 100644
--- a/arch/arm/mach-shmobile/platsmp.c
+++ b/arch/arm/mach-shmobile/platsmp.c
@@ -56,6 +56,12 @@
unsigned int ncores = shmobile_smp_get_core_count();
unsigned int i;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
+ }
+
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
diff --git a/arch/arm/mach-tegra/platsmp.c b/arch/arm/mach-tegra/platsmp.c
index 0886cbc..7d2b5d0 100644
--- a/arch/arm/mach-tegra/platsmp.c
+++ b/arch/arm/mach-tegra/platsmp.c
@@ -114,10 +114,10 @@
{
unsigned int i, ncores = scu_get_core_count(scu_base);
- if (ncores > NR_CPUS) {
- printk(KERN_ERR "Tegra: no. of cores (%u) greater than configured (%u), clipping\n",
- ncores, NR_CPUS);
- ncores = NR_CPUS;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index a33df5f..eb51991 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -156,12 +156,10 @@
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
- if (ncores > NR_CPUS) {
- printk(KERN_WARNING
- "U8500: no. of cores (%d) greater than configured "
- "maximum of %d - clipping\n",
- ncores, NR_CPUS);
- ncores = NR_CPUS;
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index bfd32f5..2b1e836 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -221,6 +221,12 @@
{
int i, ncores = scu_get_core_count(MMIO_P2V(A9_MPCORE_SCU));
+ if (ncores > nr_cpu_ids) {
+ pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
+ ncores, nr_cpu_ids);
+ ncores = nr_cpu_ids;
+ }
+
for (i = 0; i < ncores; ++i)
set_cpu_possible(i, true);
diff --git a/arch/arm/mach-vexpress/include/mach/io.h b/arch/arm/mach-vexpress/include/mach/io.h
index 748bb52..13522d8 100644
--- a/arch/arm/mach-vexpress/include/mach/io.h
+++ b/arch/arm/mach-vexpress/include/mach/io.h
@@ -20,8 +20,6 @@
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffffffff
-
#define __io(a) __typesafe_io(a)
#define __mem_pci(a) (a)
diff --git a/arch/arm/mach-vt8500/include/mach/io.h b/arch/arm/mach-vt8500/include/mach/io.h
index 9077239..46181ee 100644
--- a/arch/arm/mach-vt8500/include/mach/io.h
+++ b/arch/arm/mach-vt8500/include/mach/io.h
@@ -20,8 +20,6 @@
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#define IO_SPACE_LIMIT 0xffff
-
#define __io(a) __typesafe_io((a) + 0xf0000000)
#define __mem_pci(a) (a)
diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c
index cfbcf8b..c335c76 100644
--- a/arch/arm/mm/alignment.c
+++ b/arch/arm/mm/alignment.c
@@ -86,16 +86,6 @@
#define UM_FIXUP (1 << 1)
#define UM_SIGNAL (1 << 2)
-#ifdef CONFIG_PROC_FS
-static const char *usermode_action[] = {
- "ignored",
- "warn",
- "fixup",
- "fixup+warn",
- "signal",
- "signal+warn"
-};
-
/* Return true if and only if the ARMv6 unaligned access model is in use. */
static bool cpu_is_v6_unaligned(void)
{
@@ -123,6 +113,16 @@
return new_usermode;
}
+#ifdef CONFIG_PROC_FS
+static const char *usermode_action[] = {
+ "ignored",
+ "warn",
+ "fixup",
+ "fixup+warn",
+ "signal",
+ "signal+warn"
+};
+
static int alignment_proc_show(struct seq_file *m, void *v)
{
seq_printf(m, "User:\t\t%lu\n", ai_user);
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 9ecfdb5..3f9b998 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -16,9 +16,12 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
+#include <linux/err.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/cacheflush.h>
#include <asm/hardware/cache-l2x0.h>
@@ -30,11 +33,19 @@
static uint32_t l2x0_way_mask; /* Bitmask of active ways */
static uint32_t l2x0_size;
+struct l2x0_regs l2x0_saved_regs;
+
+struct l2x0_of_data {
+ void (*setup)(const struct device_node *, __u32 *, __u32 *);
+ void (*save)(void);
+ void (*resume)(void);
+};
+
static inline void cache_wait_way(void __iomem *reg, unsigned long mask)
{
/* wait for cache operation by line or way to complete */
while (readl_relaxed(reg) & mask)
- ;
+ cpu_relax();
}
#ifdef CONFIG_CACHE_PL310
@@ -277,7 +288,7 @@
spin_unlock_irqrestore(&l2x0_lock, flags);
}
-static void __init l2x0_unlock(__u32 cache_id)
+static void l2x0_unlock(__u32 cache_id)
{
int lockregs;
int i;
@@ -353,6 +364,8 @@
/* l2x0 controller is disabled */
writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL);
+ l2x0_saved_regs.aux_ctrl = aux;
+
l2x0_inv_all();
/* enable L2X0 */
@@ -372,3 +385,202 @@
printk(KERN_INFO "l2x0: %d ways, CACHE_ID 0x%08x, AUX_CTRL 0x%08x, Cache size: %d B\n",
ways, cache_id, aux, l2x0_size);
}
+
+#ifdef CONFIG_OF
+static void __init l2x0_of_setup(const struct device_node *np,
+ __u32 *aux_val, __u32 *aux_mask)
+{
+ u32 data[2] = { 0, 0 };
+ u32 tag = 0;
+ u32 dirty = 0;
+ u32 val = 0, mask = 0;
+
+ of_property_read_u32(np, "arm,tag-latency", &tag);
+ if (tag) {
+ mask |= L2X0_AUX_CTRL_TAG_LATENCY_MASK;
+ val |= (tag - 1) << L2X0_AUX_CTRL_TAG_LATENCY_SHIFT;
+ }
+
+ of_property_read_u32_array(np, "arm,data-latency",
+ data, ARRAY_SIZE(data));
+ if (data[0] && data[1]) {
+ mask |= L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK |
+ L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK;
+ val |= ((data[0] - 1) << L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT) |
+ ((data[1] - 1) << L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT);
+ }
+
+ of_property_read_u32(np, "arm,dirty-latency", &dirty);
+ if (dirty) {
+ mask |= L2X0_AUX_CTRL_DIRTY_LATENCY_MASK;
+ val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT;
+ }
+
+ *aux_val &= ~mask;
+ *aux_val |= val;
+ *aux_mask &= ~mask;
+}
+
+static void __init pl310_of_setup(const struct device_node *np,
+ __u32 *aux_val, __u32 *aux_mask)
+{
+ u32 data[3] = { 0, 0, 0 };
+ u32 tag[3] = { 0, 0, 0 };
+ u32 filter[2] = { 0, 0 };
+
+ of_property_read_u32_array(np, "arm,tag-latency", tag, ARRAY_SIZE(tag));
+ if (tag[0] && tag[1] && tag[2])
+ writel_relaxed(
+ ((tag[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+ ((tag[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+ ((tag[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+ l2x0_base + L2X0_TAG_LATENCY_CTRL);
+
+ of_property_read_u32_array(np, "arm,data-latency",
+ data, ARRAY_SIZE(data));
+ if (data[0] && data[1] && data[2])
+ writel_relaxed(
+ ((data[0] - 1) << L2X0_LATENCY_CTRL_RD_SHIFT) |
+ ((data[1] - 1) << L2X0_LATENCY_CTRL_WR_SHIFT) |
+ ((data[2] - 1) << L2X0_LATENCY_CTRL_SETUP_SHIFT),
+ l2x0_base + L2X0_DATA_LATENCY_CTRL);
+
+ of_property_read_u32_array(np, "arm,filter-ranges",
+ filter, ARRAY_SIZE(filter));
+ if (filter[1]) {
+ writel_relaxed(ALIGN(filter[0] + filter[1], SZ_1M),
+ l2x0_base + L2X0_ADDR_FILTER_END);
+ writel_relaxed((filter[0] & ~(SZ_1M - 1)) | L2X0_ADDR_FILTER_EN,
+ l2x0_base + L2X0_ADDR_FILTER_START);
+ }
+}
+
+static void __init pl310_save(void)
+{
+ u32 l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) &
+ L2X0_CACHE_ID_RTL_MASK;
+
+ l2x0_saved_regs.tag_latency = readl_relaxed(l2x0_base +
+ L2X0_TAG_LATENCY_CTRL);
+ l2x0_saved_regs.data_latency = readl_relaxed(l2x0_base +
+ L2X0_DATA_LATENCY_CTRL);
+ l2x0_saved_regs.filter_end = readl_relaxed(l2x0_base +
+ L2X0_ADDR_FILTER_END);
+ l2x0_saved_regs.filter_start = readl_relaxed(l2x0_base +
+ L2X0_ADDR_FILTER_START);
+
+ if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) {
+ /*
+ * From r2p0, there is Prefetch offset/control register
+ */
+ l2x0_saved_regs.prefetch_ctrl = readl_relaxed(l2x0_base +
+ L2X0_PREFETCH_CTRL);
+ /*
+ * From r3p0, there is Power control register
+ */
+ if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0)
+ l2x0_saved_regs.pwr_ctrl = readl_relaxed(l2x0_base +
+ L2X0_POWER_CTRL);
+ }
+}
+
+static void l2x0_resume(void)
+{
+ if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+ /* restore aux ctrl and enable l2 */
+ l2x0_unlock(readl_relaxed(l2x0_base + L2X0_CACHE_ID));
+
+ writel_relaxed(l2x0_saved_regs.aux_ctrl, l2x0_base +
+ L2X0_AUX_CTRL);
+
+ l2x0_inv_all();
+
+ writel_relaxed(1, l2x0_base + L2X0_CTRL);
+ }
+}
+
+static void pl310_resume(void)
+{
+ u32 l2x0_revision;
+
+ if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+ /* restore pl310 setup */
+ writel_relaxed(l2x0_saved_regs.tag_latency,
+ l2x0_base + L2X0_TAG_LATENCY_CTRL);
+ writel_relaxed(l2x0_saved_regs.data_latency,
+ l2x0_base + L2X0_DATA_LATENCY_CTRL);
+ writel_relaxed(l2x0_saved_regs.filter_end,
+ l2x0_base + L2X0_ADDR_FILTER_END);
+ writel_relaxed(l2x0_saved_regs.filter_start,
+ l2x0_base + L2X0_ADDR_FILTER_START);
+
+ l2x0_revision = readl_relaxed(l2x0_base + L2X0_CACHE_ID) &
+ L2X0_CACHE_ID_RTL_MASK;
+
+ if (l2x0_revision >= L2X0_CACHE_ID_RTL_R2P0) {
+ writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
+ l2x0_base + L2X0_PREFETCH_CTRL);
+ if (l2x0_revision >= L2X0_CACHE_ID_RTL_R3P0)
+ writel_relaxed(l2x0_saved_regs.pwr_ctrl,
+ l2x0_base + L2X0_POWER_CTRL);
+ }
+ }
+
+ l2x0_resume();
+}
+
+static const struct l2x0_of_data pl310_data = {
+ pl310_of_setup,
+ pl310_save,
+ pl310_resume,
+};
+
+static const struct l2x0_of_data l2x0_data = {
+ l2x0_of_setup,
+ NULL,
+ l2x0_resume,
+};
+
+static const struct of_device_id l2x0_ids[] __initconst = {
+ { .compatible = "arm,pl310-cache", .data = (void *)&pl310_data },
+ { .compatible = "arm,l220-cache", .data = (void *)&l2x0_data },
+ { .compatible = "arm,l210-cache", .data = (void *)&l2x0_data },
+ {}
+};
+
+int __init l2x0_of_init(__u32 aux_val, __u32 aux_mask)
+{
+ struct device_node *np;
+ struct l2x0_of_data *data;
+ struct resource res;
+
+ np = of_find_matching_node(NULL, l2x0_ids);
+ if (!np)
+ return -ENODEV;
+
+ if (of_address_to_resource(np, 0, &res))
+ return -ENODEV;
+
+ l2x0_base = ioremap(res.start, resource_size(&res));
+ if (!l2x0_base)
+ return -ENOMEM;
+
+ l2x0_saved_regs.phy_base = res.start;
+
+ data = of_match_node(l2x0_ids, np)->data;
+
+ /* L2 configuration can only be changed if the cache is disabled */
+ if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+ if (data->setup)
+ data->setup(np, &aux_val, &aux_mask);
+ }
+
+ if (data->save)
+ data->save();
+
+ l2x0_init(l2x0_base, aux_val, aux_mask);
+
+ outer_cache.resume = data->resume;
+ return 0;
+}
+#endif
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index c3ff82f..235eb77 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -123,8 +123,8 @@
#endif
#define CONSISTENT_OFFSET(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PAGE_SHIFT)
-#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PGDIR_SHIFT)
-#define NUM_CONSISTENT_PTES (CONSISTENT_DMA_SIZE >> PGDIR_SHIFT)
+#define CONSISTENT_PTE_INDEX(x) (((unsigned long)(x) - CONSISTENT_BASE) >> PMD_SHIFT)
+#define NUM_CONSISTENT_PTES (CONSISTENT_DMA_SIZE >> PMD_SHIFT)
/*
* These are the page tables (2MB each) covering uncached, DMA consistent allocations
@@ -183,7 +183,7 @@
}
consistent_pte[i++] = pte;
- base += (1 << PGDIR_SHIFT);
+ base += PMD_SIZE;
} while (base < CONSISTENT_END);
return ret;
diff --git a/arch/arm/mm/fault.c b/arch/arm/mm/fault.c
index 3b5ea68..aa33949 100644
--- a/arch/arm/mm/fault.c
+++ b/arch/arm/mm/fault.c
@@ -20,6 +20,7 @@
#include <linux/highmem.h>
#include <linux/perf_event.h>
+#include <asm/exception.h>
#include <asm/system.h>
#include <asm/pgtable.h>
#include <asm/tlbflush.h>
diff --git a/arch/arm/mm/mm.h b/arch/arm/mm/mm.h
index 0105667..ad7cce3 100644
--- a/arch/arm/mm/mm.h
+++ b/arch/arm/mm/mm.h
@@ -12,8 +12,8 @@
struct mem_type {
pteval_t prot_pte;
- unsigned int prot_l1;
- unsigned int prot_sect;
+ pmdval_t prot_l1;
+ pmdval_t prot_sect;
unsigned int domain;
};
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 594d677..226f180 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -60,7 +60,7 @@
struct cachepolicy {
const char policy[16];
unsigned int cr_mask;
- unsigned int pmd;
+ pmdval_t pmd;
pteval_t pte;
};
@@ -288,7 +288,7 @@
{
struct cachepolicy *cp;
unsigned int cr = get_cr();
- unsigned int user_pgprot, kern_pgprot, vecs_pgprot;
+ pteval_t user_pgprot, kern_pgprot, vecs_pgprot;
int cpu_arch = cpu_architecture();
int i;
@@ -863,14 +863,14 @@
/*
* Clear out all the mappings below the kernel image.
*/
- for (addr = 0; addr < MODULES_VADDR; addr += PGDIR_SIZE)
+ for (addr = 0; addr < MODULES_VADDR; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
#ifdef CONFIG_XIP_KERNEL
/* The XIP kernel is mapped in the module area -- skip over it */
- addr = ((unsigned long)_etext + PGDIR_SIZE - 1) & PGDIR_MASK;
+ addr = ((unsigned long)_etext + PMD_SIZE - 1) & PMD_MASK;
#endif
- for ( ; addr < PAGE_OFFSET; addr += PGDIR_SIZE)
+ for ( ; addr < PAGE_OFFSET; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
/*
@@ -885,10 +885,12 @@
* memory bank, up to the end of the vmalloc region.
*/
for (addr = __phys_to_virt(end);
- addr < VMALLOC_END; addr += PGDIR_SIZE)
+ addr < VMALLOC_END; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
}
+#define SWAPPER_PG_DIR_SIZE (PTRS_PER_PGD * sizeof(pgd_t))
+
/*
* Reserve the special regions of memory
*/
@@ -898,7 +900,7 @@
* Reserve the page tables. These are already in use,
* and can only be in node 0.
*/
- memblock_reserve(__pa(swapper_pg_dir), PTRS_PER_PGD * sizeof(pgd_t));
+ memblock_reserve(__pa(swapper_pg_dir), SWAPPER_PG_DIR_SIZE);
#ifdef CONFIG_SA1111
/*
@@ -926,7 +928,7 @@
*/
vectors_page = early_alloc(PAGE_SIZE);
- for (addr = VMALLOC_END; addr; addr += PGDIR_SIZE)
+ for (addr = VMALLOC_END; addr; addr += PMD_SIZE)
pmd_clear(pmd_off_k(addr));
/*
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index 9049c07..9591c8e 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -218,7 +218,7 @@
/* Suspend/resume support: derived from arch/arm/mach-s5pv210/sleep.S */
.globl cpu_v7_suspend_size
.equ cpu_v7_suspend_size, 4 * 9
-#ifdef CONFIG_PM_SLEEP
+#ifdef CONFIG_ARM_CPU_SUSPEND
ENTRY(cpu_v7_do_suspend)
stmfd sp!, {r4 - r11, lr}
mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
index bb8f4a6..5b605a9 100644
--- a/arch/arm/plat-omap/Kconfig
+++ b/arch/arm/plat-omap/Kconfig
@@ -14,6 +14,7 @@
select CLKDEV_LOOKUP
select CLKSRC_MMIO
select GENERIC_IRQ_CHIP
+ select HAVE_IDE
help
"Systems based on omap7xx, omap15xx or omap16xx"
diff --git a/arch/arm/vfp/Makefile b/arch/arm/vfp/Makefile
index 6de73aa..a81404c 100644
--- a/arch/arm/vfp/Makefile
+++ b/arch/arm/vfp/Makefile
@@ -7,7 +7,7 @@
# ccflags-y := -DDEBUG
# asflags-y := -DDEBUG
-KBUILD_AFLAGS :=$(KBUILD_AFLAGS:-msoft-float=-Wa,-mfpu=softvfp+vfp)
+KBUILD_AFLAGS :=$(KBUILD_AFLAGS:-msoft-float=-Wa,-mfpu=softvfp+vfp -mfloat-abi=soft)
LDFLAGS +=--no-warn-mismatch
obj-y += vfp.o
diff --git a/lib/Kconfig.debug b/lib/Kconfig.debug
index c0cb9c4..103c171 100644
--- a/lib/Kconfig.debug
+++ b/lib/Kconfig.debug
@@ -1081,7 +1081,7 @@
depends on FAULT_INJECTION_DEBUG_FS && STACKTRACE_SUPPORT
depends on !X86_64
select STACKTRACE
- select FRAME_POINTER if !PPC && !S390 && !MICROBLAZE
+ select FRAME_POINTER if !PPC && !S390 && !MICROBLAZE && !ARM_UNWIND
help
Provide stacktrace filter for fault-injection capabilities
@@ -1091,7 +1091,7 @@
depends on DEBUG_KERNEL
depends on STACKTRACE_SUPPORT
depends on PROC_FS
- select FRAME_POINTER if !MIPS && !PPC && !S390 && !MICROBLAZE
+ select FRAME_POINTER if !MIPS && !PPC && !S390 && !MICROBLAZE && !ARM_UNWIND
select KALLSYMS
select KALLSYMS_ALL
select STACKTRACE