Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6028): Turn an unnecessary mdelay() into msleep().
  V4L/DVB (6027): Get rid of an ill-behaved msleep in i2c write
  V4L/DVB (6026): Avoid powering up the camera on resume
  V4L/DVB (6016): get_dvb_firmware: update script for new location of tda10046 firmware
  V4L/DVB (5991): dvb-pll: Set minimum and maximum frequency properly
  V4L/DVB (5969): ivtv: report ivtv version in status log
  V4L/DVB (5967): ivtv: fix VIDIOC_S_FBUF:new OSD values where never set
  V4L/DVB (5968): videodev2.h: remove superfluous FBUF GLOBAL_INV_ALPHA support
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 4680e20..3e79bf0 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -44,8 +44,18 @@
 		#size-cells = <1>;
 		#interrupt-cells = <2>;
 		device_type = "soc";
-		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00100000>;	// CCSRBAR 1M
+
+
+		ranges = <00001000 e0001000 000ff000
+			  80000000 80000000 20000000
+			  a0000000 a0000000 10000000
+			  b0000000 b0000000 00100000
+			  c0000000 c0000000 20000000
+			  b0100000 b0100000 00100000
+			  e1000000 e1000000 00010000
+			  e1010000 e1010000 00010000
+			  e1020000 e1020000 00010000>;
+		reg = <e0000000 00001000>;	// CCSRBAR 1M
 		bus-frequency = <0>;		// Filled out by uboot.
 
 		memory-controller@2000 {
@@ -161,8 +171,8 @@
 			interrupt-parent = <&mpic>;
 			interrupts = <18 2>;
 			bus-range = <0 ff>;
-			ranges = <02000000 0 80000000 80000000 0 10000000
-				  01000000 0 00000000 e2000000 0 00800000>;
+			ranges = <02000000 0 c0000000 c0000000 0 20000000
+				  01000000 0 00000000 e1000000 0 00010000>;
 			clock-frequency = <3f940aa>;
 			#interrupt-cells = <1>;
 			#size-cells = <2>;
@@ -178,8 +188,8 @@
 			#address-cells = <3>;
 			reg = <9000 1000>;
 			bus-range = <0 ff>;
-			ranges = <02000000 0 90000000 90000000 0 10000000
-				  01000000 0 00000000 e3000000 0 00800000>;
+			ranges = <02000000 0 80000000 80000000 0 20000000
+				  01000000 0 00000000 e1010000 0 00010000>;
 			clock-frequency = <1fca055>;
 			interrupt-parent = <&mpic>;
 			interrupts = <1a 2>;
@@ -202,7 +212,7 @@
 			reg = <a000 1000>;
 			bus-range = <0 ff>;
 			ranges = <02000000 0 a0000000 a0000000 0 10000000
-				  01000000 0 00000000 e2800000 0 00800000>;
+				  01000000 0 00000000 e1020000 0 00010000>;
 			clock-frequency = <1fca055>;
 			interrupt-parent = <&mpic>;
 			interrupts = <19 2>;
@@ -224,49 +234,29 @@
 			#address-cells = <3>;
 			reg = <b000 1000>;
 			bus-range = <0 ff>;
-			ranges = <02000000 0 b0000000 b0000000 0 10000000
-				  01000000 0 00000000 e3800000 0 00800000>;
+			ranges = <02000000 0 b0000000 b0000000 0 00100000
+				  01000000 0 00000000 b0100000 0 00100000>;
 			clock-frequency = <1fca055>;
 			interrupt-parent = <&mpic>;
 			interrupts = <1b 2>;
-			interrupt-map-mask = <f800 0 0 7>;
+			interrupt-map-mask = <fb00 0 0 0>;
 			interrupt-map = <
-
-				// IDSEL 0x1a
-				d000 0 0 1 &i8259 6 2
-				d000 0 0 2 &i8259 3 2
-				d000 0 0 3 &i8259 4 2
-				d000 0 0 4 &i8259 5 2
-
-				// IDSEL 0x1b
-				d800 0 0 1 &i8259 5 2
-				d800 0 0 2 &i8259 0 0
-				d800 0 0 3 &i8259 0 0
-				d800 0 0 4 &i8259 0 0
-
 				// IDSEL 0x1c  USB
-				e000 0 0 1 &i8259 9 2
-				e000 0 0 2 &i8259 a 2
-				e000 0 0 3 &i8259 c 2
-				e000 0 0 4 &i8259 7 2
+				e000 0 0 0 &i8259 c 2
+				e100 0 0 0 &i8259 9 2
+				e200 0 0 0 &i8259 a 2
+				e300 0 0 0 &i8259 b 2
 
 				// IDSEL 0x1d  Audio
-				e800 0 0 1 &i8259 9 2
-				e800 0 0 2 &i8259 a 2
-				e800 0 0 3 &i8259 b 2
-				e800 0 0 4 &i8259 0 0
+				e800 0 0 0 &i8259 6 2
 
 				// IDSEL 0x1e Legacy
-				f000 0 0 1 &i8259 c 2
-				f000 0 0 2 &i8259 0 0
-				f000 0 0 3 &i8259 0 0
-				f000 0 0 4 &i8259 0 0
+				f000 0 0 0 &i8259 7 2
+				f100 0 0 0 &i8259 7 2
 
 				// IDSEL 0x1f IDE/SATA
-				f800 0 0 1 &i8259 6 2
-				f800 0 0 2 &i8259 0 0
-				f800 0 0 3 &i8259 0 0
-				f800 0 0 4 &i8259 0 0
+				f800 0 0 0 &i8259 e 2
+				f900 0 0 0 &i8259 5 2
 			>;
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
@@ -274,10 +264,10 @@
 				#address-cells = <3>;
 				ranges = <02000000 0 b0000000
 					  02000000 0 b0000000
-					  0 10000000
+					  0 00100000
 					  01000000 0 00000000
 					  01000000 0 00000000
-					  0 00080000>;
+					  0 00100000>;
 
 				pci_bridge@0 {
 					reg = <0 0 0 0 0>;
@@ -285,10 +275,10 @@
 					#address-cells = <3>;
 					ranges = <02000000 0 b0000000
 						  02000000 0 b0000000
-						  0 20000000
+						  0 00100000
 						  01000000 0 00000000
 						  01000000 0 00000000
-						  0 00100000>;
+						  0 00100000>; 
 
 					isa@1e {
 						device_type = "isa";
@@ -296,7 +286,8 @@
 						#size-cells = <1>;
 						#address-cells = <2>;
 						reg = <f000 0 0 0 0>;
-						ranges = <1 0 01000000 0 0
+						ranges = <1 0
+							  01000000 0 0
 							  00001000>;
 						interrupt-parent = <&i8259>;
 
@@ -312,8 +303,7 @@
 							built-in;
 							compatible = "chrp,iic";
 							interrupts = <9 2>;
-							interrupt-parent =
-								<&mpic>;
+							interrupt-parent = <&mpic>;
 						};
 
 						i8042@60 {
@@ -321,8 +311,7 @@
 							#address-cells = <1>;
 							reg = <1 60 1 1 64 1>;
 							interrupts = <1 3 c 3>;
-							interrupt-parent =
-								<&i8259>;
+							interrupt-parent = <&i8259>;
 
 							keyboard@0 {
 								reg = <0>;
@@ -336,8 +325,7 @@
 						};
 
 						rtc@70 {
-							compatible =
-								"pnpPNP,b00";
+							compatible = "pnpPNP,b00";
 							reg = <1 70 2>;
 						};
 
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 5d82709..b0166e5 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -224,98 +224,36 @@
 			clock-frequency = <1fca055>;
 			interrupt-parent = <&mpic>;
 			interrupts = <18 2>;
-			interrupt-map-mask = <f800 0 0 7>;
+			interrupt-map-mask = <fb00 0 0 0>;
 			interrupt-map = <
 				/* IDSEL 0x11 */
-				8800 0 0 1 &i8259 3 2
-				8800 0 0 2 &i8259 4 2
-				8800 0 0 3 &i8259 5 2
-				8800 0 0 4 &i8259 6 2
+				8800 0 0 1 &i8259 9 2
+				8800 0 0 2 &i8259 a 2
+				8800 0 0 3 &i8259 b 2
+				8800 0 0 4 &i8259 c 2
 
 				/* IDSEL 0x12 */
-				9000 0 0 1 &i8259 4 2
-				9000 0 0 2 &i8259 5 2
-				9000 0 0 3 &i8259 6 2
-				9000 0 0 4 &i8259 3 2
+				9000 0 0 1 &i8259 a 2
+				9000 0 0 2 &i8259 b 2
+				9000 0 0 3 &i8259 c 2
+				9000 0 0 4 &i8259 9 2
 
-				/* IDSEL 0x13 */
-				9800 0 0 1 &i8259 0 0
-				9800 0 0 2 &i8259 0 0
-				9800 0 0 3 &i8259 0 0
-				9800 0 0 4 &i8259 0 0
+				// IDSEL 0x1c  USB
+				e000 0 0 0 &i8259 c 2
+				e100 0 0 0 &i8259 9 2
+				e200 0 0 0 &i8259 a 2
+				e300 0 0 0 &i8259 b 2
 
-				/* IDSEL 0x14 */
-				a000 0 0 1 &i8259 0 0
-				a000 0 0 2 &i8259 0 0
-				a000 0 0 3 &i8259 0 0
-				a000 0 0 4 &i8259 0 0
+				// IDSEL 0x1d  Audio
+				e800 0 0 0 &i8259 6 2
 
-				/* IDSEL 0x15 */
-				a800 0 0 1 &i8259 0 0
-				a800 0 0 2 &i8259 0 0
-				a800 0 0 3 &i8259 0 0
-				a800 0 0 4 &i8259 0 0
+				// IDSEL 0x1e Legacy
+				f000 0 0 0 &i8259 7 2
+				f100 0 0 0 &i8259 7 2
 
-				/* IDSEL 0x16 */
-				b000 0 0 1 &i8259 0 0
-				b000 0 0 2 &i8259 0 0
-				b000 0 0 3 &i8259 0 0
-				b000 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x17 */
-				b800 0 0 1 &i8259 0 0
-				b800 0 0 2 &i8259 0 0
-				b800 0 0 3 &i8259 0 0
-				b800 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x18 */
-				c000 0 0 1 &i8259 0 0
-				c000 0 0 2 &i8259 0 0
-				c000 0 0 3 &i8259 0 0
-				c000 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x19 */
-				c800 0 0 1 &i8259 0 0
-				c800 0 0 2 &i8259 0 0
-				c800 0 0 3 &i8259 0 0
-				c800 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x1a */
-				d000 0 0 1 &i8259 6 2
-				d000 0 0 2 &i8259 3 2
-				d000 0 0 3 &i8259 4 2
-				d000 0 0 4 &i8259 5 2
-
-
-				/* IDSEL 0x1b */
-				d800 0 0 1 &i8259 5 2
-				d800 0 0 2 &i8259 0 0
-				d800 0 0 3 &i8259 0 0
-				d800 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x1c */
-				e000 0 0 1 &i8259 9 2
-				e000 0 0 2 &i8259 a 2
-				e000 0 0 3 &i8259 c 2
-				e000 0 0 4 &i8259 7 2
-
-				/* IDSEL 0x1d */
-				e800 0 0 1 &i8259 9 2
-				e800 0 0 2 &i8259 a 2
-				e800 0 0 3 &i8259 b 2
-				e800 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x1e */
-				f000 0 0 1 &i8259 c 2
-				f000 0 0 2 &i8259 0 0
-				f000 0 0 3 &i8259 0 0
-				f000 0 0 4 &i8259 0 0
-
-				/* IDSEL 0x1f */
-				f800 0 0 1 &i8259 6 2
-				f800 0 0 2 &i8259 0 0
-				f800 0 0 3 &i8259 0 0
-				f800 0 0 4 &i8259 0 0
+				// IDSEL 0x1f IDE/SATA
+				f800 0 0 0 &i8259 e 2
+				f900 0 0 0 &i8259 5 2
 				>;
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index 2bb1cb9..d8502e3 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -299,7 +299,7 @@
 #ifndef CONFIG_FSL_BOOKE
 #define get_mc_reason(regs)	((regs)->dsisr)
 #else
-#define get_mc_reason(regs)	(mfspr(SPRN_MCSR))
+#define get_mc_reason(regs)	(mfspr(SPRN_MCSR) & MCSR_MASK)
 #endif
 #define REASON_FP		ESR_FP
 #define REASON_ILLEGAL		(ESR_PIL | ESR_PUO)
@@ -414,8 +414,6 @@
 		printk("Data Cache Push Parity Error\n");
 	if (reason & MCSR_DCPERR)
 		printk("Data Cache Parity Error\n");
-	if (reason & MCSR_GL_CI)
-		printk("Guarded Load or Cache-Inhibited stwcx.\n");
 	if (reason & MCSR_BUS_IAERR)
 		printk("Bus - Instruction Address Error\n");
 	if (reason & MCSR_BUS_RAERR)
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index f581840..f620171 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -33,6 +33,7 @@
 	bool "Freescale MPC8544 DS"
 	select PPC_I8259
 	select DEFAULT_UIMAGE
+	select FSL_ULI1575
 	help
 	  This option enables support for the MPC8544 DS board
 
diff --git a/arch/powerpc/platforms/85xx/mpc8544_ds.c b/arch/powerpc/platforms/85xx/mpc8544_ds.c
index 4905f6f..0f834d8 100644
--- a/arch/powerpc/platforms/85xx/mpc8544_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8544_ds.c
@@ -114,211 +114,25 @@
 }
 
 #ifdef CONFIG_PCI
-enum pirq { PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH };
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+				u_char bus, u_char devfn);
 
-/*
- * Value in  table -- IRQ number
- */
-const unsigned char uli1575_irq_route_table[16] = {
-	0,		/* 0: Reserved */
-	0x8,
-	0,		/* 2: Reserved */
-	0x2,
-	0x4,
-	0x5,
-	0x7,
-	0x6,
-	0,		/* 8: Reserved */
-	0x1,
-	0x3,
-	0x9,
-	0xb,
-	0,		/* 13: Reserved */
-	0xd,
-	0xf,
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
+static int mpc85xx_exclude_device(struct pci_controller *hose,
+				   u_char bus, u_char devfn)
 {
-	struct of_irq oirq;
-	u32 laddr[3];
-	struct device_node *hosenode = hose ? hose->arch_data : NULL;
+	struct device_node* node;	
+	struct resource rsrc;
 
-	if (!hosenode)
-		return -EINVAL;
+	node = (struct device_node *)hose->arch_data;
+	of_address_to_resource(node, 0, &rsrc);
 
-	laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
-	laddr[1] = laddr[2] = 0;
-	of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
-	DBG("mpc8544_ds: pci irq addr %x, slot %d, pin %d, irq %d\n",
-	    laddr[0], slot, pin, oirq.specifier[0]);
-	return oirq.specifier[0];
+	if ((rsrc.start & 0xfffff) == 0xb000) {
+		return uli_exclude_device(hose, bus, devfn);
+	}
+
+	return PCIBIOS_SUCCESSFUL;
 }
-
-/*8259*/
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
-	unsigned short temp;
-	struct pci_controller *hose = pci_bus_to_host(dev->bus);
-	unsigned char irq2pin[16];
-	unsigned long pirq_map_word = 0;
-	u32 irq;
-	int i;
-
-	/*
-	 * ULI1575 interrupts route setup
-	 */
-	memset(irq2pin, 0, 16);	/* Initialize default value 0 */
-
-	irq2pin[6]=PIRQA+3;	/* enabled mapping for IRQ6 to PIRQD, used by SATA */
-
-	/*
-	 * PIRQE -> PIRQF mapping set manually
-	 *
-	 * IRQ pin   IRQ#
-	 * PIRQE ---- 9
-	 * PIRQF ---- 10
-	 * PIRQG ---- 11
-	 * PIRQH ---- 12
-	 */
-	for (i = 0; i < 4; i++)
-		irq2pin[i + 9] = PIRQE + i;
-
-	/* Set IRQ-PIRQ Mapping to ULI1575 */
-	for (i = 0; i < 16; i++)
-		if (irq2pin[i])
-			pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
-			    << ((irq2pin[i] - PIRQA) * 4);
-
-	pirq_map_word |= 1<<26;	/* disable INTx in EP mode*/
-
-	/* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
-	DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
-		(int)pirq_map_word);
-	pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg)				\
-	do {								\
-		int irq;						\
-		irq = get_pci_irq_from_of(hose, slot, pin);		\
-		if (irq > 0 && irq < 16) 				\
-			pci_write_config_byte(dev, reg, irq2pin[irq]);	\
-		else							\
-			printk(KERN_WARNING "ULI1575 device"		\
-				"(slot %d, pin %d) irq %d is invalid.\n", \
-				slot, pin, irq);			\
-	} while(0)
-
-	/* USB 1.1 OHCI controller 1, slot 28, pin 1 */
-	ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
-	/* USB 1.1 OHCI controller 2, slot 28, pin 2 */
-	ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
-	/* USB 1.1 OHCI controller 3, slot 28, pin 3 */
-	ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
-	/* USB 2.0 controller, slot 28, pin 4 */
-	irq = get_pci_irq_from_of(hose, 28, 4);
-	if (irq >= 0 && irq <= 15)
-		pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
-	/* Audio controller, slot 29, pin 1 */
-	ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
-	/* Modem controller, slot 29, pin 2 */
-	ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
-	/* HD audio controller, slot 29, pin 3 */
-	ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
-	/* SMB interrupt: slot 30, pin 1 */
-	ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
-	/* PMU ACPI SCI interrupt: slot 30, pin 2 */
-	ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
-	/* Serial ATA interrupt: slot 31, pin 1 */
-	ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
-	/* Primary PATA IDE IRQ: 14
-	 * Secondary PATA IDE IRQ: 15
-	 */
-	pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
-	pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
-	/* Set IRQ14 and IRQ15 to legacy IRQs */
-	pci_read_config_word(dev, 0x46, &temp);
-	temp |= 0xc000;
-	pci_write_config_word(dev, 0x46, temp);
-
-	/* Set i8259 interrupt trigger
-	 * IRQ 3:  Level
-	 * IRQ 4:  Level
-	 * IRQ 5:  Level
-	 * IRQ 6:  Level
-	 * IRQ 7:  Level
-	 * IRQ 9:  Level
-	 * IRQ 10: Level
-	 * IRQ 11: Level
-	 * IRQ 12: Level
-	 * IRQ 14: Edge
-	 * IRQ 15: Edge
-	 */
-	outb(0xfa, 0x4d0);
-	outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-}
-
-/* SATA */
-static void __devinit quirk_uli5288(struct pci_dev *dev)
-{
-	unsigned char c;
-
-	pci_read_config_byte(dev, 0x83, &c);
-	c |= 0x80;		/* read/write lock */
-	pci_write_config_byte(dev, 0x83, c);
-
-	pci_write_config_byte(dev, 0x09, 0x01);	/* Base class code: storage */
-	pci_write_config_byte(dev, 0x0a, 0x06);	/* IDE disk */
-
-	pci_read_config_byte(dev, 0x83, &c);
-	c &= 0x7f;
-	pci_write_config_byte(dev, 0x83, c);
-
-	pci_read_config_byte(dev, 0x84, &c);
-	c |= 0x01;				/* emulated PATA mode enabled */
-	pci_write_config_byte(dev, 0x84, c);
-}
-
-/* PATA */
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
-	unsigned short temp;
-	pci_write_config_word(dev, 0x04, 0x0405);	/* MEM IO MSI */
-	pci_read_config_word(dev, 0x4a, &temp);
-	temp |= 0x1000;				/* Enable Native IRQ 14/15 */
-	pci_write_config_word(dev, 0x4a, temp);
-}
-
-/*Bridge*/
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
-	unsigned char temp;
-	pci_write_config_word(dev, 0x04, 0x0007);	/* mem access */
-	pci_read_config_byte(dev, 0x7c, &temp);
-	pci_write_config_byte(dev, 0x7c, 0x80);	/* R/W lock control */
-	pci_write_config_byte(dev, 0x09, 0x01);	/* set as pci-pci bridge */
-	pci_write_config_byte(dev, 0x7c, temp);	/* restore pci bus debug control */
-	dev->class |= 0x1;
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
 #endif	/* CONFIG_PCI */
 
 /*
@@ -342,6 +156,8 @@
 		else
 			fsl_add_bridge(np, 0);
 	}
+	uses_fsl_uli_m1575 = 1;
+	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
 #endif
 
 	printk("MPC8544 DS board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig
index 343b76d..685b2fb 100644
--- a/arch/powerpc/platforms/86xx/Kconfig
+++ b/arch/powerpc/platforms/86xx/Kconfig
@@ -7,6 +7,7 @@
 	bool "Freescale MPC8641 HPCN"
 	select PPC_I8259
 	select DEFAULT_UIMAGE
+	select FSL_ULI1575
 	help
 	  This option enables support for the MPC8641 HPCN board.
 
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index e9eaa07..56b27ca 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -107,220 +107,25 @@
 }
 
 #ifdef CONFIG_PCI
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+				u_char bus, u_char devfn);
 
-enum pirq{PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH};
-const unsigned char uli1575_irq_route_table[16] = {
-	0, 	/* 0: Reserved */
-	0x8, 	/* 1: 0b1000 */
-	0, 	/* 2: Reserved */
-	0x2,	/* 3: 0b0010 */
-	0x4,	/* 4: 0b0100 */
-	0x5, 	/* 5: 0b0101 */
-	0x7,	/* 6: 0b0111 */
-	0x6,	/* 7: 0b0110 */
-	0, 	/* 8: Reserved */
-	0x1,	/* 9: 0b0001 */
-	0x3,	/* 10: 0b0011 */
-	0x9,	/* 11: 0b1001 */
-	0xb,	/* 12: 0b1011 */
-	0, 	/* 13: Reserved */
-	0xd,	/* 14, 0b1101 */
-	0xf,	/* 15, 0b1111 */
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
+static int mpc86xx_exclude_device(struct pci_controller *hose,
+				   u_char bus, u_char devfn)
 {
-	struct of_irq oirq;
-	u32 laddr[3];
-	struct device_node *hosenode = hose ? hose->arch_data : NULL;
+	struct device_node* node;	
+	struct resource rsrc;
 
-	if (!hosenode) return -EINVAL;
+	node = (struct device_node *)hose->arch_data;
+	of_address_to_resource(node, 0, &rsrc);
 
-	laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
-	laddr[1] = laddr[2] = 0;
-	of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
-	DBG("mpc86xx_hpcn: pci irq addr %x, slot %d, pin %d, irq %d\n",
-			laddr[0], slot, pin, oirq.specifier[0]);
-	return oirq.specifier[0];
-}
-
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
-	unsigned short temp;
-	struct pci_controller *hose = pci_bus_to_host(dev->bus);
-	unsigned char irq2pin[16], c;
-	unsigned long pirq_map_word = 0;
-	u32 irq;
-	int i;
-
-	/*
-	 * ULI1575 interrupts route setup
-	 */
-	memset(irq2pin, 0, 16); /* Initialize default value 0 */
-
-	/*
-	 * PIRQA -> PIRQD mapping read from OF-tree
-	 *
-	 * interrupts for PCI slot0 -- PIRQA / PIRQB / PIRQC / PIRQD
-	 *                PCI slot1 -- PIRQB / PIRQC / PIRQD / PIRQA
-	 */
-	for (i = 0; i < 4; i++){
-		irq = get_pci_irq_from_of(hose, 17, i + 1);
-		if (irq > 0 && irq < 16)
-			irq2pin[irq] = PIRQA + i;
-		else
-			printk(KERN_WARNING "ULI1575 device"
-			    "(slot %d, pin %d) irq %d is invalid.\n",
-			    17, i, irq);
+	if ((rsrc.start & 0xfffff) == 0x8000) {
+		return uli_exclude_device(hose, bus, devfn);
 	}
 
-	/*
-	 * PIRQE -> PIRQF mapping set manually
-	 *
-	 * IRQ pin   IRQ#
-	 * PIRQE ---- 9
-	 * PIRQF ---- 10
-	 * PIRQG ---- 11
-	 * PIRQH ---- 12
-	 */
-	for (i = 0; i < 4; i++) irq2pin[i + 9] = PIRQE + i;
-
-	/* Set IRQ-PIRQ Mapping to ULI1575 */
-	for (i = 0; i < 16; i++)
-		if (irq2pin[i])
-			pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
-				<< ((irq2pin[i] - PIRQA) * 4);
-
-	/* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
-	DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
-			pirq_map_word);
-	pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg) 				\
-	do { 								\
-		int irq; 						\
-		irq = get_pci_irq_from_of(hose, slot, pin); 		\
-		if (irq > 0 && irq < 16) 				\
-			pci_write_config_byte(dev, reg, irq2pin[irq]); 	\
-		else							\
-			printk(KERN_WARNING "ULI1575 device"		\
-			    "(slot %d, pin %d) irq %d is invalid.\n",	\
-			    slot, pin, irq);				\
-	} while(0)
-
-	/* USB 1.1 OHCI controller 1, slot 28, pin 1 */
-	ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
-	/* USB 1.1 OHCI controller 2, slot 28, pin 2 */
-	ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
-	/* USB 1.1 OHCI controller 3, slot 28, pin 3 */
-	ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
-	/* USB 2.0 controller, slot 28, pin 4 */
-	irq = get_pci_irq_from_of(hose, 28, 4);
-	if (irq >= 0 && irq <=15)
-		pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
-	/* Audio controller, slot 29, pin 1 */
-	ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
-	/* Modem controller, slot 29, pin 2 */
-	ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
-	/* HD audio controller, slot 29, pin 3 */
-	ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
-	/* SMB interrupt: slot 30, pin 1 */
-	ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
-	/* PMU ACPI SCI interrupt: slot 30, pin 2 */
-	ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
-	/* Serial ATA interrupt: slot 31, pin 1 */
-	ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
-	/* Primary PATA IDE IRQ: 14
-	 * Secondary PATA IDE IRQ: 15
-	 */
-	pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
-	pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
-	/* Set IRQ14 and IRQ15 to legacy IRQs */
-	pci_read_config_word(dev, 0x46, &temp);
-	temp |= 0xc000;
-	pci_write_config_word(dev, 0x46, temp);
-
-	/* Set i8259 interrupt trigger
-	 * IRQ 3:  Level
-	 * IRQ 4:  Level
-	 * IRQ 5:  Level
-	 * IRQ 6:  Level
-	 * IRQ 7:  Level
-	 * IRQ 9:  Level
-	 * IRQ 10: Level
-	 * IRQ 11: Level
-	 * IRQ 12: Level
-	 * IRQ 14: Edge
-	 * IRQ 15: Edge
-	 */
-	outb(0xfa, 0x4d0);
-	outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-
-	/* Disable the HD interface and enable the AC97 interface. */
-	pci_read_config_byte(dev, 0xb8, &c);
-	c &= 0x7f;
-	pci_write_config_byte(dev, 0xb8, c);
+	return PCIBIOS_SUCCESSFUL;
 }
-
-static void __devinit quirk_uli5288(struct pci_dev *dev)
-{
-	unsigned char c;
-
-	pci_read_config_byte(dev,0x83,&c);
-	c |= 0x80;
-	pci_write_config_byte(dev, 0x83, c);
-
-	pci_write_config_byte(dev, 0x09, 0x01);
-	pci_write_config_byte(dev, 0x0a, 0x06);
-
-	pci_read_config_byte(dev,0x83,&c);
-	c &= 0x7f;
-	pci_write_config_byte(dev, 0x83, c);
-
-	pci_read_config_byte(dev,0x84,&c);
-	c |= 0x01;
-	pci_write_config_byte(dev, 0x84, c);
-}
-
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
-	unsigned short temp;
-	pci_write_config_word(dev, 0x04, 0x0405);
-	dev->class &= ~0x5;
-	pci_read_config_word(dev, 0x4a, &temp);
-	temp |= 0x1000;
-	pci_write_config_word(dev, 0x4a, temp);
-}
-
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
-	unsigned char temp;
-	pci_write_config_word(dev, 0x04, 0x0007);
-	pci_read_config_byte(dev, 0x7c, &temp);
-	pci_write_config_byte(dev, 0x7c, 0x80);
-	pci_write_config_byte(dev, 0x09, 0x01);
-	pci_write_config_byte(dev, 0x7c, temp);
-	dev->class |= 0x1;
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
 #endif /* CONFIG_PCI */
 
 
@@ -353,6 +158,9 @@
 		else
 			fsl_add_bridge(np, 0);
 	}
+	uses_fsl_uli_m1575 = 1;
+	ppc_md.pci_exclude_device = mpc86xx_exclude_device;
+
 #endif
 
 	printk("MPC86xx HPCN board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 932538a..cfc2497 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -282,4 +282,12 @@
 	  minor numbers are available in /proc/devices, /proc/partitions or
 	  in /sys/block/axonram?/dev.
 
+config FSL_ULI1575
+	bool
+	default n
+	help
+	  Supports for the ULI1575 PCIe south bridge that exists on some
+	  Freescale reference boards. The boards all use the ULI in pretty
+	  much the same way.
+
 endmenu
diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile
index d6e041a..d44e832 100644
--- a/arch/powerpc/platforms/Makefile
+++ b/arch/powerpc/platforms/Makefile
@@ -1,3 +1,6 @@
+
+obj-$(CONFIG_FSL_ULI1575)	+= fsl_uli1575.o
+
 ifeq ($(CONFIG_PPC_MERGE),y)
 obj-$(CONFIG_PPC_PMAC)		+= powermac/
 else
diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
new file mode 100644
index 0000000..afc9141
--- /dev/null
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -0,0 +1,255 @@
+/*
+ * ULI M1575 setup code - specific to Freescale boards
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+
+#include <asm/system.h>
+#include <asm/pci-bridge.h>
+
+#define ULI_PIRQA	0x08
+#define ULI_PIRQB	0x09
+#define ULI_PIRQC	0x0a
+#define ULI_PIRQD	0x0b
+#define ULI_PIRQE	0x0c
+#define ULI_PIRQF	0x0d
+#define ULI_PIRQG	0x0e
+
+#define ULI_8259_NONE	0x00
+#define ULI_8259_IRQ1	0x08
+#define ULI_8259_IRQ3	0x02
+#define ULI_8259_IRQ4	0x04
+#define ULI_8259_IRQ5	0x05
+#define ULI_8259_IRQ6	0x07
+#define ULI_8259_IRQ7	0x06
+#define ULI_8259_IRQ9	0x01
+#define ULI_8259_IRQ10	0x03
+#define ULI_8259_IRQ11	0x09
+#define ULI_8259_IRQ12	0x0b
+#define ULI_8259_IRQ14	0x0d
+#define ULI_8259_IRQ15	0x0f
+
+u8 uli_pirq_to_irq[8] = {
+	ULI_8259_IRQ9,		/* PIRQA */
+	ULI_8259_IRQ10,		/* PIRQB */
+	ULI_8259_IRQ11,		/* PIRQC */
+	ULI_8259_IRQ12,		/* PIRQD */
+	ULI_8259_IRQ5,		/* PIRQE */
+	ULI_8259_IRQ6,		/* PIRQF */
+	ULI_8259_IRQ7,		/* PIRQG */
+	ULI_8259_NONE,		/* PIRQH */
+};
+
+/* set in board code if you want this quirks to do something */
+int uses_fsl_uli_m1575;
+
+/* Bridge */
+static void __devinit early_uli5249(struct pci_dev *dev)
+{
+	unsigned char temp;
+
+	if (!uses_fsl_uli_m1575)
+		return;
+
+	pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_IO |
+		 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+	/* read/write lock */
+	pci_read_config_byte(dev, 0x7c, &temp);
+	pci_write_config_byte(dev, 0x7c, 0x80);
+
+	/* set as P2P bridge */
+	pci_write_config_byte(dev, PCI_CLASS_PROG, 0x01);
+	dev->class |= 0x1;
+
+	/* restore lock */
+	pci_write_config_byte(dev, 0x7c, temp);
+}
+
+
+static void __devinit quirk_uli1575(struct pci_dev *dev)
+{
+	int i;
+
+	if (!uses_fsl_uli_m1575)
+		return;
+
+	/*
+	 * ULI1575 interrupts route setup
+	 */
+
+	/* ULI1575 IRQ mapping conf register maps PIRQx to IRQn */
+	for (i = 0; i < 4; i++) {
+		u8 val = uli_pirq_to_irq[i*2] | (uli_pirq_to_irq[i*2+1] << 4);
+		pci_write_config_byte(dev, 0x48 + i, val);
+	}
+
+	/* USB 1.1 OHCI controller 1: dev 28, func 0 - IRQ12 */
+	pci_write_config_byte(dev, 0x86, ULI_PIRQD);
+
+	/* USB 1.1 OHCI controller 2: dev 28, func 1 - IRQ9 */
+	pci_write_config_byte(dev, 0x87, ULI_PIRQA);
+
+	/* USB 1.1 OHCI controller 3: dev 28, func 2 - IRQ10 */
+	pci_write_config_byte(dev, 0x88, ULI_PIRQB);
+
+	/* Lan controller: dev 27, func 0 - IRQ6 */
+	pci_write_config_byte(dev, 0x89, ULI_PIRQF);
+
+	/* AC97 Audio controller: dev 29, func 0 - IRQ6 */
+	pci_write_config_byte(dev, 0x8a, ULI_PIRQF);
+
+	/* Modem controller: dev 29, func 1 - IRQ6 */
+	pci_write_config_byte(dev, 0x8b, ULI_PIRQF);
+
+	/* HD Audio controller: dev 29, func 2 - IRQ6 */
+	pci_write_config_byte(dev, 0x8c, ULI_PIRQF);
+
+	/* SATA controller: dev 31, func 1 - IRQ5 */
+	pci_write_config_byte(dev, 0x8d, ULI_PIRQE);
+
+	/* SMB interrupt: dev 30, func 1 - IRQ7 */
+	pci_write_config_byte(dev, 0x8e, ULI_PIRQG);
+
+	/* PMU ACPI SCI interrupt: dev 30, func 2 - IRQ7 */
+	pci_write_config_byte(dev, 0x8f, ULI_PIRQG);
+
+	/* USB 2.0 controller: dev 28, func 3 */
+	pci_write_config_byte(dev, 0x74, ULI_8259_IRQ11);
+
+	/* Primary PATA IDE IRQ: 14
+	 * Secondary PATA IDE IRQ: 15
+	 */
+	pci_write_config_byte(dev, 0x44, 0x30 | ULI_8259_IRQ14);
+	pci_write_config_byte(dev, 0x75, ULI_8259_IRQ15);
+}
+
+static void __devinit quirk_final_uli1575(struct pci_dev *dev)
+{
+	/* Set i8259 interrupt trigger
+	 * IRQ 3:  Level
+	 * IRQ 4:  Level
+	 * IRQ 5:  Level
+	 * IRQ 6:  Level
+	 * IRQ 7:  Level
+	 * IRQ 9:  Level
+	 * IRQ 10: Level
+	 * IRQ 11: Level
+	 * IRQ 12: Level
+	 * IRQ 14: Edge
+	 * IRQ 15: Edge
+	 */
+	if (!uses_fsl_uli_m1575)
+		return;
+
+	outb(0xfa, 0x4d0);
+	outb(0x1e, 0x4d1);
+
+	/* setup RTC */
+	CMOS_WRITE(RTC_SET, RTC_CONTROL);
+	CMOS_WRITE(RTC_24H, RTC_CONTROL);
+
+	/* ensure month, date, and week alarm fields are ignored */
+	CMOS_WRITE(0, RTC_VALID);
+
+	outb_p(0x7c, 0x72);
+	outb_p(RTC_ALARM_DONT_CARE, 0x73);
+
+	outb_p(0x7d, 0x72);
+	outb_p(RTC_ALARM_DONT_CARE, 0x73);
+}
+
+/* SATA */
+static void __devinit quirk_uli5288(struct pci_dev *dev)
+{
+	unsigned char c;
+	unsigned int d;
+
+	if (!uses_fsl_uli_m1575)
+		return;
+
+	/* read/write lock */
+	pci_read_config_byte(dev, 0x83, &c);
+	pci_write_config_byte(dev, 0x83, c|0x80);
+
+	pci_read_config_dword(dev, PCI_CLASS_REVISION, &d);
+	d = (d & 0xff) | (PCI_CLASS_STORAGE_SATA_AHCI << 8);
+	pci_write_config_dword(dev, PCI_CLASS_REVISION, d);
+
+	/* restore lock */
+	pci_write_config_byte(dev, 0x83, c);
+
+	/* disable emulated PATA mode enabled */
+	pci_read_config_byte(dev, 0x84, &c);
+	pci_write_config_byte(dev, 0x84, c & ~0x01);
+}
+
+/* PATA */
+static void __devinit quirk_uli5229(struct pci_dev *dev)
+{
+	unsigned short temp;
+
+	if (!uses_fsl_uli_m1575)
+		return;
+
+	pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE |
+		PCI_COMMAND_MASTER | PCI_COMMAND_IO);
+
+	/* Enable Native IRQ 14/15 */
+	pci_read_config_word(dev, 0x4a, &temp);
+	pci_write_config_word(dev, 0x4a, temp | 0x1000);
+}
+
+/* We have to do a dummy read on the P2P for the RTC to work, WTF */
+static void __devinit quirk_final_uli5249(struct pci_dev *dev)
+{
+	int i;
+	u8 *dummy;
+	struct pci_bus *bus = dev->bus;
+
+	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
+		if ((bus->resource[i]) &&
+			(bus->resource[i]->flags & IORESOURCE_MEM)) {
+			dummy = ioremap(bus->resource[i]->start, 0x4);
+			if (dummy) {
+				in_8(dummy);
+				iounmap(dummy);
+			}
+			break;
+		}
+	}
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5249, quirk_final_uli5249);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x1575, quirk_final_uli1575);
+
+int uli_exclude_device(struct pci_controller *hose,
+			u_char bus, u_char devfn)
+{
+	if (bus == (hose->first_busno + 2)) {
+		/* exclude Modem controller */
+		if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 1))
+			return PCIBIOS_DEVICE_NOT_FOUND;
+
+		/* exclude HD Audio controller */
+		if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 2))
+			return PCIBIOS_DEVICE_NOT_FOUND;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
index 727453d..1cf29c9 100644
--- a/arch/powerpc/sysdev/fsl_soc.c
+++ b/arch/powerpc/sysdev/fsl_soc.c
@@ -22,6 +22,7 @@
 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
+#include <linux/of_platform.h>
 #include <linux/phy.h>
 #include <linux/fsl_devices.h>
 #include <linux/fs_enet_pd.h>
diff --git a/arch/powerpc/sysdev/rtc_cmos_setup.c b/arch/powerpc/sysdev/rtc_cmos_setup.c
index e276048..0c9ac7e 100644
--- a/arch/powerpc/sysdev/rtc_cmos_setup.c
+++ b/arch/powerpc/sysdev/rtc_cmos_setup.c
@@ -20,14 +20,16 @@
 {
 	struct device_node *np;
 	struct platform_device *pd;
-	struct resource res;
+	struct resource res[2];
 	int ret;
 
+	memset(&res, 0, sizeof(res));
+
 	np = of_find_compatible_node(NULL, NULL, "pnpPNP,b00");
 	if (!np)
 		return -ENODEV;
 
-	ret = of_address_to_resource(np, 0, &res);
+	ret = of_address_to_resource(np, 0, &res[0]);
 	of_node_put(np);
 	if (ret)
 		return ret;
@@ -36,11 +38,18 @@
 	 * RTC_PORT(x) is hardcoded in asm/mc146818rtc.h.  Verify that the
 	 * address provided by the device node matches.
 	 */
-	if (res.start != RTC_PORT(0))
+	if (res[0].start != RTC_PORT(0))
 		return -EINVAL;
 
+	/* Use a fixed interrupt value of 8 since on PPC if we are using this
+	 * its off an i8259 which we ensure has interrupt numbers 0..15. */
+	res[1].start = 8;
+	res[1].end = 8;
+	res[1].flags = IORESOURCE_IRQ;
+
 	pd = platform_device_register_simple("rtc_cmos", -1,
-					     &res, 1);
+					     &res[0], 2);
+
 	if (IS_ERR(pd))
 		return PTR_ERR(pd);
 
diff --git a/drivers/kvm/kvm_main.c b/drivers/kvm/kvm_main.c
index 9685609..cd05579 100644
--- a/drivers/kvm/kvm_main.c
+++ b/drivers/kvm/kvm_main.c
@@ -2974,6 +2974,10 @@
 	switch (val) {
 	case CPU_DYING:
 	case CPU_DYING_FROZEN:
+		printk(KERN_INFO "kvm: disabling virtualization on CPU%d\n",
+		       cpu);
+		hardware_disable(NULL);
+		break;
 	case CPU_UP_CANCELED:
 	case CPU_UP_CANCELED_FROZEN:
 		printk(KERN_INFO "kvm: disabling virtualization on CPU%d\n",
diff --git a/fs/jffs2/write.c b/fs/jffs2/write.c
index bc61859..664c164 100644
--- a/fs/jffs2/write.c
+++ b/fs/jffs2/write.c
@@ -566,6 +566,9 @@
 		struct jffs2_full_dirent **prev = &dir_f->dents;
 		uint32_t nhash = full_name_hash(name, namelen);
 
+		/* We don't actually want to reserve any space, but we do
+		   want to be holding the alloc_sem when we write to flash */
+		down(&c->alloc_sem);
 		down(&dir_f->sem);
 
 		while ((*prev) && (*prev)->nhash <= nhash) {
diff --git a/include/asm-powerpc/reg_booke.h b/include/asm-powerpc/reg_booke.h
index 064405c..8fdc2b4 100644
--- a/include/asm-powerpc/reg_booke.h
+++ b/include/asm-powerpc/reg_booke.h
@@ -223,7 +223,6 @@
 #define MCSR_ICPERR 	0x40000000UL /* I-Cache Parity Error */
 #define MCSR_DCP_PERR 	0x20000000UL /* D-Cache Push Parity Error */
 #define MCSR_DCPERR 	0x10000000UL /* D-Cache Parity Error */
-#define MCSR_GL_CI 	0x00010000UL /* Guarded Load or Cache-Inhibited stwcx. */
 #define MCSR_BUS_IAERR 	0x00000080UL /* Instruction Address Error */
 #define MCSR_BUS_RAERR 	0x00000040UL /* Read Address Error */
 #define MCSR_BUS_WAERR 	0x00000020UL /* Write Address Error */
@@ -232,6 +231,12 @@
 #define MCSR_BUS_WBERR 	0x00000004UL /* Write Data Bus Error */
 #define MCSR_BUS_IPERR 	0x00000002UL /* Instruction parity Error */
 #define MCSR_BUS_RPERR 	0x00000001UL /* Read parity Error */
+
+/* e500 parts may set unused bits in MCSR; mask these off */
+#define MCSR_MASK	(MCSR_MCP | MCSR_ICPERR | MCSR_DCP_PERR | \
+			MCSR_DCPERR | MCSR_BUS_IAERR | MCSR_BUS_RAERR | \
+			MCSR_BUS_WAERR | MCSR_BUS_IBERR | MCSR_BUS_RBERR | \
+			MCSR_BUS_WBERR | MCSR_BUS_IPERR | MCSR_BUS_RPERR)
 #endif
 #ifdef CONFIG_E200
 #define MCSR_MCP 	0x80000000UL /* Machine Check Input Pin */
@@ -243,6 +248,11 @@
 #define MCSR_BUS_DRERR 	0x00000008UL /* Read Bus Error on data load */
 #define MCSR_BUS_WRERR 	0x00000004UL /* Write Bus Error on buffered
 					store or cache line push */
+
+/* e200 parts may set unused bits in MCSR; mask these off */
+#define MCSR_MASK	(MCSR_MCP | MCSR_CP_PERR | MCSR_CPERR | \
+			MCSR_EXCP_ERR | MCSR_BUS_IRERR | MCSR_BUS_DRERR | \
+			MCSR_BUS_WRERR)
 #endif
 
 /* Bit definitions for the DBSR. */
diff --git a/kernel/printk.c b/kernel/printk.c
index bd2cd06..5c7c325 100644
--- a/kernel/printk.c
+++ b/kernel/printk.c
@@ -1083,6 +1083,17 @@
 }
 EXPORT_SYMBOL(unregister_console);
 
+static int __init disable_boot_consoles(void)
+{
+	if (console_drivers->flags & CON_BOOT) {
+		printk(KERN_INFO "turn off boot console %s%d\n",
+			console_drivers->name, console_drivers->index);
+		return unregister_console(console_drivers);
+	}
+	return 0;
+}
+late_initcall(disable_boot_consoles);
+
 /**
  * tty_write_message - write a message to a certain tty, not just the console.
  * @tty: the destination tty_struct
diff --git a/kernel/sysctl.c b/kernel/sysctl.c
index 8bdb8c0..9029690 100644
--- a/kernel/sysctl.c
+++ b/kernel/sysctl.c
@@ -27,7 +27,6 @@
 #include <linux/capability.h>
 #include <linux/ctype.h>
 #include <linux/utsname.h>
-#include <linux/capability.h>
 #include <linux/smp_lock.h>
 #include <linux/fs.h>
 #include <linux/init.h>
diff --git a/net/bridge/br_sysfs_br.c b/net/bridge/br_sysfs_br.c
index 88f4300..c65f54e 100644
--- a/net/bridge/br_sysfs_br.c
+++ b/net/bridge/br_sysfs_br.c
@@ -167,6 +167,7 @@
 	br_stp_set_enabled(br, val);
 	rtnl_unlock();
 
+	return len;
 }
 static DEVICE_ATTR(stp_state, S_IRUGO | S_IWUSR, show_stp_state,
 		   store_stp_state);