ixgbe:add support for a new 82599 10G Base-T device
This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 9551cbb..d571d10 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -108,6 +108,8 @@
board_82599 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_CX4),
board_82599 },
+ {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_T3_LOM),
+ board_82599 },
{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_COMBO_BACKPLANE),
board_82599 },
@@ -1618,6 +1620,48 @@
}
}
+/**
+ * ixgbe_check_overtemp_task - worker thread to check over tempurature
+ * @work: pointer to work_struct containing our data
+ **/
+static void ixgbe_check_overtemp_task(struct work_struct *work)
+{
+ struct ixgbe_adapter *adapter = container_of(work,
+ struct ixgbe_adapter,
+ check_overtemp_task);
+ struct ixgbe_hw *hw = &adapter->hw;
+ u32 eicr = adapter->interrupt_event;
+
+ if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) {
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_82599_T3_LOM: {
+ u32 autoneg;
+ bool link_up = false;
+
+ if (hw->mac.ops.check_link)
+ hw->mac.ops.check_link(hw, &autoneg, &link_up, false);
+
+ if (((eicr & IXGBE_EICR_GPI_SDP0) && (!link_up)) ||
+ (eicr & IXGBE_EICR_LSC))
+ /* Check if this is due to overtemp */
+ if (hw->phy.ops.check_overtemp(hw) == IXGBE_ERR_OVERTEMP)
+ break;
+ }
+ return;
+ default:
+ if (!(eicr & IXGBE_EICR_GPI_SDP0))
+ return;
+ break;
+ }
+ DPRINTK(DRV, ERR, "Network adapter has been stopped because it "
+ "has over heated. Restart the computer. If the problem "
+ "persists, power off the system and replace the "
+ "adapter\n");
+ /* write to clear the interrupt */
+ IXGBE_WRITE_REG(hw, IXGBE_EICR, IXGBE_EICR_GPI_SDP0);
+ }
+}
+
static void ixgbe_check_fan_failure(struct ixgbe_adapter *adapter, u32 eicr)
{
struct ixgbe_hw *hw = &adapter->hw;
@@ -1689,6 +1733,10 @@
if (hw->mac.type == ixgbe_mac_82599EB) {
ixgbe_check_sfp_event(adapter, eicr);
+ adapter->interrupt_event = eicr;
+ if ((adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) &&
+ ((eicr & IXGBE_EICR_GPI_SDP0) || (eicr & IXGBE_EICR_LSC)))
+ schedule_work(&adapter->check_overtemp_task);
/* Handle Flow Director Full threshold interrupt */
if (eicr & IXGBE_EICR_FLOW_DIR) {
@@ -2190,6 +2238,8 @@
u32 mask;
mask = (IXGBE_EIMS_ENABLE_MASK & ~IXGBE_EIMS_RTX_QUEUE);
+ if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE)
+ mask |= IXGBE_EIMS_GPI_SDP0;
if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE)
mask |= IXGBE_EIMS_GPI_SDP1;
if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
@@ -2250,6 +2300,9 @@
ixgbe_check_sfp_event(adapter, eicr);
ixgbe_check_fan_failure(adapter, eicr);
+ if ((adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) &&
+ ((eicr & IXGBE_EICR_GPI_SDP0) || (eicr & IXGBE_EICR_LSC)))
+ schedule_work(&adapter->check_overtemp_task);
if (napi_schedule_prep(&(q_vector->napi))) {
adapter->tx_ring[0]->total_packets = 0;
@@ -3265,6 +3318,13 @@
IXGBE_WRITE_REG(hw, IXGBE_EIAM, IXGBE_EICS_RTX_QUEUE);
}
+ /* Enable Thermal over heat sensor interrupt */
+ if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) {
+ gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
+ gpie |= IXGBE_SDP0_GPIEN;
+ IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
+ }
+
/* Enable fan failure interrupt if media type is copper */
if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE) {
gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
@@ -3666,6 +3726,9 @@
adapter->flags & IXGBE_FLAG_FDIR_PERFECT_CAPABLE)
cancel_work_sync(&adapter->fdir_reinit_task);
+ if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE)
+ cancel_work_sync(&adapter->check_overtemp_task);
+
/* disable transmits in the hardware now that interrupts are off */
for (i = 0; i < adapter->num_tx_queues; i++) {
j = adapter->tx_ring[i]->reg_idx;
@@ -4645,6 +4708,8 @@
adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82599;
adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE;
adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED;
+ if (hw->device_id == IXGBE_DEV_ID_82599_T3_LOM)
+ adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
if (dev->features & NETIF_F_NTUPLE) {
/* Flow Director perfect filter enabled */
adapter->flags |= IXGBE_FLAG_FDIR_PERFECT_CAPABLE;
@@ -6561,7 +6626,9 @@
}
/* reset_hw fills in the perm_addr as well */
+ hw->phy.reset_if_overtemp = true;
err = hw->mac.ops.reset_hw(hw);
+ hw->phy.reset_if_overtemp = false;
if (err == IXGBE_ERR_SFP_NOT_PRESENT &&
hw->mac.type == ixgbe_mac_82598EB) {
/*
@@ -6730,6 +6797,8 @@
adapter->flags & IXGBE_FLAG_FDIR_PERFECT_CAPABLE)
INIT_WORK(&adapter->fdir_reinit_task, ixgbe_fdir_reinit_task);
+ if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE)
+ INIT_WORK(&adapter->check_overtemp_task, ixgbe_check_overtemp_task);
#ifdef CONFIG_IXGBE_DCA
if (dca_add_requester(&pdev->dev) == 0) {
adapter->flags |= IXGBE_FLAG_DCA_ENABLED;