| /* |
| * linux/include/linux/mtd/nand.h |
| * |
| * Copyright (c) 2000 David Woodhouse <dwmw2@infradead.org> |
| * Steven J. Hill <sjhill@realitydiluted.com> |
| * Thomas Gleixner <tglx@linutronix.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * Info: |
| * Contains standard defines and IDs for NAND flash devices |
| * |
| * Changelog: |
| * See git changelog. |
| */ |
| #ifndef __LINUX_MTD_NAND_H |
| #define __LINUX_MTD_NAND_H |
| |
| #include <linux/wait.h> |
| #include <linux/spinlock.h> |
| #include <linux/mtd/mtd.h> |
| |
| struct mtd_info; |
| /* Scan and identify a NAND device */ |
| extern int nand_scan (struct mtd_info *mtd, int max_chips); |
| /* Separate phases of nand_scan(), allowing board driver to intervene |
| * and override command or ECC setup according to flash type */ |
| extern int nand_scan_ident(struct mtd_info *mtd, int max_chips); |
| extern int nand_scan_tail(struct mtd_info *mtd); |
| |
| /* Free resources held by the NAND device */ |
| extern void nand_release (struct mtd_info *mtd); |
| |
| /* Internal helper for board drivers which need to override command function */ |
| extern void nand_wait_ready(struct mtd_info *mtd); |
| |
| /* The maximum number of NAND chips in an array */ |
| #define NAND_MAX_CHIPS 8 |
| |
| /* This constant declares the max. oobsize / page, which |
| * is supported now. If you add a chip with bigger oobsize/page |
| * adjust this accordingly. |
| */ |
| #define NAND_MAX_OOBSIZE 64 |
| #define NAND_MAX_PAGESIZE 2048 |
| |
| /* |
| * Constants for hardware specific CLE/ALE/NCE function |
| * |
| * These are bits which can be or'ed to set/clear multiple |
| * bits in one go. |
| */ |
| /* Select the chip by setting nCE to low */ |
| #define NAND_NCE 0x01 |
| /* Select the command latch by setting CLE to high */ |
| #define NAND_CLE 0x02 |
| /* Select the address latch by setting ALE to high */ |
| #define NAND_ALE 0x04 |
| |
| #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) |
| #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) |
| #define NAND_CTRL_CHANGE 0x80 |
| |
| /* |
| * Standard NAND flash commands |
| */ |
| #define NAND_CMD_READ0 0 |
| #define NAND_CMD_READ1 1 |
| #define NAND_CMD_RNDOUT 5 |
| #define NAND_CMD_PAGEPROG 0x10 |
| #define NAND_CMD_READOOB 0x50 |
| #define NAND_CMD_ERASE1 0x60 |
| #define NAND_CMD_STATUS 0x70 |
| #define NAND_CMD_STATUS_MULTI 0x71 |
| #define NAND_CMD_SEQIN 0x80 |
| #define NAND_CMD_RNDIN 0x85 |
| #define NAND_CMD_READID 0x90 |
| #define NAND_CMD_ERASE2 0xd0 |
| #define NAND_CMD_RESET 0xff |
| |
| /* Extended commands for large page devices */ |
| #define NAND_CMD_READSTART 0x30 |
| #define NAND_CMD_RNDOUTSTART 0xE0 |
| #define NAND_CMD_CACHEDPROG 0x15 |
| |
| /* Extended commands for AG-AND device */ |
| /* |
| * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but |
| * there is no way to distinguish that from NAND_CMD_READ0 |
| * until the remaining sequence of commands has been completed |
| * so add a high order bit and mask it off in the command. |
| */ |
| #define NAND_CMD_DEPLETE1 0x100 |
| #define NAND_CMD_DEPLETE2 0x38 |
| #define NAND_CMD_STATUS_MULTI 0x71 |
| #define NAND_CMD_STATUS_ERROR 0x72 |
| /* multi-bank error status (banks 0-3) */ |
| #define NAND_CMD_STATUS_ERROR0 0x73 |
| #define NAND_CMD_STATUS_ERROR1 0x74 |
| #define NAND_CMD_STATUS_ERROR2 0x75 |
| #define NAND_CMD_STATUS_ERROR3 0x76 |
| #define NAND_CMD_STATUS_RESET 0x7f |
| #define NAND_CMD_STATUS_CLEAR 0xff |
| |
| #define NAND_CMD_NONE -1 |
| |
| /* Status bits */ |
| #define NAND_STATUS_FAIL 0x01 |
| #define NAND_STATUS_FAIL_N1 0x02 |
| #define NAND_STATUS_TRUE_READY 0x20 |
| #define NAND_STATUS_READY 0x40 |
| #define NAND_STATUS_WP 0x80 |
| |
| /* |
| * Constants for ECC_MODES |
| */ |
| typedef enum { |
| NAND_ECC_NONE, |
| NAND_ECC_SOFT, |
| NAND_ECC_HW, |
| NAND_ECC_HW_SYNDROME, |
| } nand_ecc_modes_t; |
| |
| /* |
| * Constants for Hardware ECC |
| */ |
| /* Reset Hardware ECC for read */ |
| #define NAND_ECC_READ 0 |
| /* Reset Hardware ECC for write */ |
| #define NAND_ECC_WRITE 1 |
| /* Enable Hardware ECC before syndrom is read back from flash */ |
| #define NAND_ECC_READSYN 2 |
| |
| /* Bit mask for flags passed to do_nand_read_ecc */ |
| #define NAND_GET_DEVICE 0x80 |
| |
| |
| /* Option constants for bizarre disfunctionality and real |
| * features |
| */ |
| /* Chip can not auto increment pages */ |
| #define NAND_NO_AUTOINCR 0x00000001 |
| /* Buswitdh is 16 bit */ |
| #define NAND_BUSWIDTH_16 0x00000002 |
| /* Device supports partial programming without padding */ |
| #define NAND_NO_PADDING 0x00000004 |
| /* Chip has cache program function */ |
| #define NAND_CACHEPRG 0x00000008 |
| /* Chip has copy back function */ |
| #define NAND_COPYBACK 0x00000010 |
| /* AND Chip which has 4 banks and a confusing page / block |
| * assignment. See Renesas datasheet for further information */ |
| #define NAND_IS_AND 0x00000020 |
| /* Chip has a array of 4 pages which can be read without |
| * additional ready /busy waits */ |
| #define NAND_4PAGE_ARRAY 0x00000040 |
| /* Chip requires that BBT is periodically rewritten to prevent |
| * bits from adjacent blocks from 'leaking' in altering data. |
| * This happens with the Renesas AG-AND chips, possibly others. */ |
| #define BBT_AUTO_REFRESH 0x00000080 |
| /* Chip does not require ready check on read. True |
| * for all large page devices, as they do not support |
| * autoincrement.*/ |
| #define NAND_NO_READRDY 0x00000100 |
| /* Chip does not allow subpage writes */ |
| #define NAND_NO_SUBPAGE_WRITE 0x00000200 |
| |
| |
| /* Options valid for Samsung large page devices */ |
| #define NAND_SAMSUNG_LP_OPTIONS \ |
| (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK) |
| |
| /* Macros to identify the above */ |
| #define NAND_CANAUTOINCR(chip) (!(chip->options & NAND_NO_AUTOINCR)) |
| #define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING)) |
| #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) |
| #define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK)) |
| /* Large page NAND with SOFT_ECC should support subpage reads */ |
| #define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \ |
| && (chip->page_shift > 9)) |
| |
| /* Mask to zero out the chip options, which come from the id table */ |
| #define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR) |
| |
| /* Non chip related options */ |
| /* Use a flash based bad block table. This option is passed to the |
| * default bad block table function. */ |
| #define NAND_USE_FLASH_BBT 0x00010000 |
| /* This option skips the bbt scan during initialization. */ |
| #define NAND_SKIP_BBTSCAN 0x00020000 |
| /* This option is defined if the board driver allocates its own buffers |
| (e.g. because it needs them DMA-coherent */ |
| #define NAND_OWN_BUFFERS 0x00040000 |
| /* Options set by nand scan */ |
| /* Nand scan has allocated controller struct */ |
| #define NAND_CONTROLLER_ALLOC 0x80000000 |
| |
| /* Cell info constants */ |
| #define NAND_CI_CHIPNR_MSK 0x03 |
| #define NAND_CI_CELLTYPE_MSK 0x0C |
| |
| /* |
| * nand_state_t - chip states |
| * Enumeration for NAND flash chip state |
| */ |
| typedef enum { |
| FL_READY, |
| FL_READING, |
| FL_WRITING, |
| FL_ERASING, |
| FL_SYNCING, |
| FL_CACHEDPRG, |
| FL_PM_SUSPENDED, |
| } nand_state_t; |
| |
| /* Keep gcc happy */ |
| struct nand_chip; |
| |
| /** |
| * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices |
| * @lock: protection lock |
| * @active: the mtd device which holds the controller currently |
| * @wq: wait queue to sleep on if a NAND operation is in progress |
| * used instead of the per chip wait queue when a hw controller is available |
| */ |
| struct nand_hw_control { |
| spinlock_t lock; |
| struct nand_chip *active; |
| wait_queue_head_t wq; |
| }; |
| |
| /** |
| * struct nand_ecc_ctrl - Control structure for ecc |
| * @mode: ecc mode |
| * @steps: number of ecc steps per page |
| * @size: data bytes per ecc step |
| * @bytes: ecc bytes per step |
| * @total: total number of ecc bytes per page |
| * @prepad: padding information for syndrome based ecc generators |
| * @postpad: padding information for syndrome based ecc generators |
| * @layout: ECC layout control struct pointer |
| * @hwctl: function to control hardware ecc generator. Must only |
| * be provided if an hardware ECC is available |
| * @calculate: function for ecc calculation or readback from ecc hardware |
| * @correct: function for ecc correction, matching to ecc generator (sw/hw) |
| * @read_page_raw: function to read a raw page without ECC |
| * @write_page_raw: function to write a raw page without ECC |
| * @read_page: function to read a page according to the ecc generator requirements |
| * @read_subpage: function to read parts of the page covered by ECC. |
| * @write_page: function to write a page according to the ecc generator requirements |
| * @read_oob: function to read chip OOB data |
| * @write_oob: function to write chip OOB data |
| */ |
| struct nand_ecc_ctrl { |
| nand_ecc_modes_t mode; |
| int steps; |
| int size; |
| int bytes; |
| int total; |
| int prepad; |
| int postpad; |
| struct nand_ecclayout *layout; |
| void (*hwctl)(struct mtd_info *mtd, int mode); |
| int (*calculate)(struct mtd_info *mtd, |
| const uint8_t *dat, |
| uint8_t *ecc_code); |
| int (*correct)(struct mtd_info *mtd, uint8_t *dat, |
| uint8_t *read_ecc, |
| uint8_t *calc_ecc); |
| int (*read_page_raw)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| uint8_t *buf); |
| void (*write_page_raw)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| const uint8_t *buf); |
| int (*read_page)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| uint8_t *buf); |
| int (*read_subpage)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| uint32_t offs, uint32_t len, |
| uint8_t *buf); |
| void (*write_page)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| const uint8_t *buf); |
| int (*read_oob)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| int page, |
| int sndcmd); |
| int (*write_oob)(struct mtd_info *mtd, |
| struct nand_chip *chip, |
| int page); |
| }; |
| |
| /** |
| * struct nand_buffers - buffer structure for read/write |
| * @ecccalc: buffer for calculated ecc |
| * @ecccode: buffer for ecc read from flash |
| * @databuf: buffer for data - dynamically sized |
| * |
| * Do not change the order of buffers. databuf and oobrbuf must be in |
| * consecutive order. |
| */ |
| struct nand_buffers { |
| uint8_t ecccalc[NAND_MAX_OOBSIZE]; |
| uint8_t ecccode[NAND_MAX_OOBSIZE]; |
| uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; |
| }; |
| |
| /** |
| * struct nand_chip - NAND Private Flash Chip Data |
| * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device |
| * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device |
| * @read_byte: [REPLACEABLE] read one byte from the chip |
| * @read_word: [REPLACEABLE] read one word from the chip |
| * @write_buf: [REPLACEABLE] write data from the buffer to the chip |
| * @read_buf: [REPLACEABLE] read data from the chip into the buffer |
| * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data |
| * @select_chip: [REPLACEABLE] select chip nr |
| * @block_bad: [REPLACEABLE] check, if the block is bad |
| * @block_markbad: [REPLACEABLE] mark the block bad |
| * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific funtion for controlling |
| * ALE/CLE/nCE. Also used to write command and address |
| * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line |
| * If set to NULL no access to ready/busy is available and the ready/busy information |
| * is read from the chip status register |
| * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip |
| * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready |
| * @ecc: [BOARDSPECIFIC] ecc control ctructure |
| * @buffers: buffer structure for read/write |
| * @hwcontrol: platform-specific hardware control structure |
| * @ops: oob operation operands |
| * @erase_cmd: [INTERN] erase command write function, selectable due to AND support |
| * @scan_bbt: [REPLACEABLE] function to scan bad block table |
| * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) |
| * @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress |
| * @state: [INTERN] the current state of the NAND device |
| * @oob_poi: poison value buffer |
| * @page_shift: [INTERN] number of address bits in a page (column address bits) |
| * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock |
| * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry |
| * @chip_shift: [INTERN] number of address bits in one chip |
| * @datbuf: [INTERN] internal buffer for one page + oob |
| * @oobbuf: [INTERN] oob buffer for one eraseblock |
| * @oobdirty: [INTERN] indicates that oob_buf must be reinitialized |
| * @data_poi: [INTERN] pointer to a data buffer |
| * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about |
| * special functionality. See the defines for further explanation |
| * @badblockpos: [INTERN] position of the bad block marker in the oob area |
| * @cellinfo: [INTERN] MLC/multichip data from chip ident |
| * @numchips: [INTERN] number of physical chips |
| * @chipsize: [INTERN] the size of one chip for multichip arrays |
| * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 |
| * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf |
| * @subpagesize: [INTERN] holds the subpagesize |
| * @ecclayout: [REPLACEABLE] the default ecc placement scheme |
| * @bbt: [INTERN] bad block table pointer |
| * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup |
| * @bbt_md: [REPLACEABLE] bad block table mirror descriptor |
| * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan |
| * @controller: [REPLACEABLE] a pointer to a hardware controller structure |
| * which is shared among multiple independend devices |
| * @priv: [OPTIONAL] pointer to private chip date |
| * @errstat: [OPTIONAL] hardware specific function to perform additional error status checks |
| * (determine if errors are correctable) |
| * @write_page: [REPLACEABLE] High-level page write function |
| */ |
| |
| struct nand_chip { |
| void __iomem *IO_ADDR_R; |
| void __iomem *IO_ADDR_W; |
| |
| uint8_t (*read_byte)(struct mtd_info *mtd); |
| u16 (*read_word)(struct mtd_info *mtd); |
| void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); |
| void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); |
| int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); |
| void (*select_chip)(struct mtd_info *mtd, int chip); |
| int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); |
| int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); |
| void (*cmd_ctrl)(struct mtd_info *mtd, int dat, |
| unsigned int ctrl); |
| int (*dev_ready)(struct mtd_info *mtd); |
| void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); |
| int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); |
| void (*erase_cmd)(struct mtd_info *mtd, int page); |
| int (*scan_bbt)(struct mtd_info *mtd); |
| int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, int status, int page); |
| int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, |
| const uint8_t *buf, int page, int cached, int raw); |
| |
| int chip_delay; |
| unsigned int options; |
| |
| int page_shift; |
| int phys_erase_shift; |
| int bbt_erase_shift; |
| int chip_shift; |
| int numchips; |
| unsigned long chipsize; |
| int pagemask; |
| int pagebuf; |
| int subpagesize; |
| uint8_t cellinfo; |
| int badblockpos; |
| |
| nand_state_t state; |
| |
| uint8_t *oob_poi; |
| struct nand_hw_control *controller; |
| struct nand_ecclayout *ecclayout; |
| |
| struct nand_ecc_ctrl ecc; |
| struct nand_buffers *buffers; |
| struct nand_hw_control hwcontrol; |
| |
| struct mtd_oob_ops ops; |
| |
| uint8_t *bbt; |
| struct nand_bbt_descr *bbt_td; |
| struct nand_bbt_descr *bbt_md; |
| |
| struct nand_bbt_descr *badblock_pattern; |
| |
| void *priv; |
| }; |
| |
| /* |
| * NAND Flash Manufacturer ID Codes |
| */ |
| #define NAND_MFR_TOSHIBA 0x98 |
| #define NAND_MFR_SAMSUNG 0xec |
| #define NAND_MFR_FUJITSU 0x04 |
| #define NAND_MFR_NATIONAL 0x8f |
| #define NAND_MFR_RENESAS 0x07 |
| #define NAND_MFR_STMICRO 0x20 |
| #define NAND_MFR_HYNIX 0xad |
| #define NAND_MFR_MICRON 0x2c |
| #define NAND_MFR_AMD 0x01 |
| |
| /** |
| * struct nand_flash_dev - NAND Flash Device ID Structure |
| * @name: Identify the device type |
| * @id: device ID code |
| * @pagesize: Pagesize in bytes. Either 256 or 512 or 0 |
| * If the pagesize is 0, then the real pagesize |
| * and the eraseize are determined from the |
| * extended id bytes in the chip |
| * @erasesize: Size of an erase block in the flash device. |
| * @chipsize: Total chipsize in Mega Bytes |
| * @options: Bitfield to store chip relevant options |
| */ |
| struct nand_flash_dev { |
| char *name; |
| int id; |
| unsigned long pagesize; |
| unsigned long chipsize; |
| unsigned long erasesize; |
| unsigned long options; |
| }; |
| |
| /** |
| * struct nand_manufacturers - NAND Flash Manufacturer ID Structure |
| * @name: Manufacturer name |
| * @id: manufacturer ID code of device. |
| */ |
| struct nand_manufacturers { |
| int id; |
| char * name; |
| }; |
| |
| extern struct nand_flash_dev nand_flash_ids[]; |
| extern struct nand_manufacturers nand_manuf_ids[]; |
| |
| /** |
| * struct nand_bbt_descr - bad block table descriptor |
| * @options: options for this descriptor |
| * @pages: the page(s) where we find the bbt, used with option BBT_ABSPAGE |
| * when bbt is searched, then we store the found bbts pages here. |
| * Its an array and supports up to 8 chips now |
| * @offs: offset of the pattern in the oob area of the page |
| * @veroffs: offset of the bbt version counter in the oob are of the page |
| * @version: version read from the bbt page during scan |
| * @len: length of the pattern, if 0 no pattern check is performed |
| * @maxblocks: maximum number of blocks to search for a bbt. This number of |
| * blocks is reserved at the end of the device where the tables are |
| * written. |
| * @reserved_block_code: if non-0, this pattern denotes a reserved (rather than |
| * bad) block in the stored bbt |
| * @pattern: pattern to identify bad block table or factory marked good / |
| * bad blocks, can be NULL, if len = 0 |
| * |
| * Descriptor for the bad block table marker and the descriptor for the |
| * pattern which identifies good and bad blocks. The assumption is made |
| * that the pattern and the version count are always located in the oob area |
| * of the first block. |
| */ |
| struct nand_bbt_descr { |
| int options; |
| int pages[NAND_MAX_CHIPS]; |
| int offs; |
| int veroffs; |
| uint8_t version[NAND_MAX_CHIPS]; |
| int len; |
| int maxblocks; |
| int reserved_block_code; |
| uint8_t *pattern; |
| }; |
| |
| /* Options for the bad block table descriptors */ |
| |
| /* The number of bits used per block in the bbt on the device */ |
| #define NAND_BBT_NRBITS_MSK 0x0000000F |
| #define NAND_BBT_1BIT 0x00000001 |
| #define NAND_BBT_2BIT 0x00000002 |
| #define NAND_BBT_4BIT 0x00000004 |
| #define NAND_BBT_8BIT 0x00000008 |
| /* The bad block table is in the last good block of the device */ |
| #define NAND_BBT_LASTBLOCK 0x00000010 |
| /* The bbt is at the given page, else we must scan for the bbt */ |
| #define NAND_BBT_ABSPAGE 0x00000020 |
| /* The bbt is at the given page, else we must scan for the bbt */ |
| #define NAND_BBT_SEARCH 0x00000040 |
| /* bbt is stored per chip on multichip devices */ |
| #define NAND_BBT_PERCHIP 0x00000080 |
| /* bbt has a version counter at offset veroffs */ |
| #define NAND_BBT_VERSION 0x00000100 |
| /* Create a bbt if none axists */ |
| #define NAND_BBT_CREATE 0x00000200 |
| /* Search good / bad pattern through all pages of a block */ |
| #define NAND_BBT_SCANALLPAGES 0x00000400 |
| /* Scan block empty during good / bad block scan */ |
| #define NAND_BBT_SCANEMPTY 0x00000800 |
| /* Write bbt if neccecary */ |
| #define NAND_BBT_WRITE 0x00001000 |
| /* Read and write back block contents when writing bbt */ |
| #define NAND_BBT_SAVECONTENT 0x00002000 |
| /* Search good / bad pattern on the first and the second page */ |
| #define NAND_BBT_SCAN2NDPAGE 0x00004000 |
| |
| /* The maximum number of blocks to scan for a bbt */ |
| #define NAND_BBT_SCAN_MAXBLOCKS 4 |
| |
| extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd); |
| extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs); |
| extern int nand_default_bbt(struct mtd_info *mtd); |
| extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); |
| extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, |
| int allowbbt); |
| extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, |
| size_t * retlen, uint8_t * buf); |
| |
| /* |
| * Constants for oob configuration |
| */ |
| #define NAND_SMALL_BADBLOCK_POS 5 |
| #define NAND_LARGE_BADBLOCK_POS 0 |
| |
| /** |
| * struct platform_nand_chip - chip level device structure |
| * @nr_chips: max. number of chips to scan for |
| * @chip_offset: chip number offset |
| * @nr_partitions: number of partitions pointed to by partitions (or zero) |
| * @partitions: mtd partition list |
| * @chip_delay: R/B delay value in us |
| * @options: Option flags, e.g. 16bit buswidth |
| * @ecclayout: ecc layout info structure |
| * @part_probe_types: NULL-terminated array of probe types |
| * @priv: hardware controller specific settings |
| */ |
| struct platform_nand_chip { |
| int nr_chips; |
| int chip_offset; |
| int nr_partitions; |
| struct mtd_partition *partitions; |
| struct nand_ecclayout *ecclayout; |
| int chip_delay; |
| unsigned int options; |
| const char **part_probe_types; |
| void *priv; |
| }; |
| |
| /** |
| * struct platform_nand_ctrl - controller level device structure |
| * @hwcontrol: platform specific hardware control structure |
| * @dev_ready: platform specific function to read ready/busy pin |
| * @select_chip: platform specific chip select function |
| * @cmd_ctrl: platform specific function for controlling |
| * ALE/CLE/nCE. Also used to write command and address |
| * @priv: private data to transport driver specific settings |
| * |
| * All fields are optional and depend on the hardware driver requirements |
| */ |
| struct platform_nand_ctrl { |
| void (*hwcontrol)(struct mtd_info *mtd, int cmd); |
| int (*dev_ready)(struct mtd_info *mtd); |
| void (*select_chip)(struct mtd_info *mtd, int chip); |
| void (*cmd_ctrl)(struct mtd_info *mtd, int dat, |
| unsigned int ctrl); |
| void *priv; |
| }; |
| |
| /** |
| * struct platform_nand_data - container structure for platform-specific data |
| * @chip: chip level chip structure |
| * @ctrl: controller level device structure |
| */ |
| struct platform_nand_data { |
| struct platform_nand_chip chip; |
| struct platform_nand_ctrl ctrl; |
| }; |
| |
| /* Some helpers to access the data structures */ |
| static inline |
| struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd) |
| { |
| struct nand_chip *chip = mtd->priv; |
| |
| return chip->priv; |
| } |
| |
| #endif /* __LINUX_MTD_NAND_H */ |