ASoC: ifdef out trace points from modules for x86

No idea why this works on ARM but not x86.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
diff --git a/sound/soc/codecs/88pm860x-codec.c b/sound/soc/codecs/88pm860x-codec.c
index a34fb92..3e798a1 100644
--- a/sound/soc/codecs/88pm860x-codec.c
+++ b/sound/soc/codecs/88pm860x-codec.c
@@ -1263,9 +1263,11 @@
 	mask = pm860x->det.hs_shrt | pm860x->det.hook_det | pm860x->det.lo_shrt
 		| pm860x->det.hp_det;
 
+#ifndef CONFIG_SND_SOC_88PM860X
 	if (status & (HEADSET_STATUS | MIC_STATUS | SHORT_HS1 | SHORT_HS2 |
 		      SHORT_LO1 | SHORT_LO2))
 		trace_snd_soc_jack_irq(dev_name(pm860x->codec->dev));
+#endif
 
 	if ((pm860x->det.hp_det & SND_JACK_HEADPHONE)
 		&& (status & HEADSET_STATUS))
diff --git a/sound/soc/codecs/wm8350.c b/sound/soc/codecs/wm8350.c
index 82d877d..db07137 100644
--- a/sound/soc/codecs/wm8350.c
+++ b/sound/soc/codecs/wm8350.c
@@ -1379,12 +1379,16 @@
 
 	switch (irq - wm8350->irq_base) {
 	case WM8350_IRQ_CODEC_JCK_DET_L:
+#ifndef CONFIG_SND_SOC_WM8350_MODULE
 		trace_snd_soc_jack_irq("WM8350 HPL");
+#endif
 		jack = &priv->hpl;
 		break;
 
 	case WM8350_IRQ_CODEC_JCK_DET_R:
+#ifndef CONFIG_SND_SOC_WM8350_MODULE
 		trace_snd_soc_jack_irq("WM8350 HPR");
+#endif
 		jack = &priv->hpr;
 		break;
 
diff --git a/sound/soc/codecs/wm8903.c b/sound/soc/codecs/wm8903.c
index b32699b..02de5ae 100644
--- a/sound/soc/codecs/wm8903.c
+++ b/sound/soc/codecs/wm8903.c
@@ -1534,8 +1534,10 @@
 	mic_report = wm8903->mic_last_report;
 	int_pol = snd_soc_read(codec, WM8903_INTERRUPT_POLARITY_1);
 
+#ifndef CONFIG_SND_SOC_WM8903_MODULE
 	if (int_val & (WM8903_MICSHRT_EINT | WM8903_MICDET_EINT))
 		trace_snd_soc_jack_irq(dev_name(codec->dev));
+#endif
 
 	if (int_val & WM8903_MICSHRT_EINT) {
 		dev_dbg(codec->dev, "Microphone short (pol=%x)\n", int_pol);
diff --git a/sound/soc/codecs/wm8962.c b/sound/soc/codecs/wm8962.c
index a24f83d..b311b46 100644
--- a/sound/soc/codecs/wm8962.c
+++ b/sound/soc/codecs/wm8962.c
@@ -3354,7 +3354,9 @@
 	if (active & (WM8962_MICSCD_EINT | WM8962_MICD_EINT)) {
 		dev_dbg(codec->dev, "Microphone event detected\n");
 
+#ifndef CONFIG_SOUND_SOC_WM862_MODULE
 		trace_snd_soc_jack_irq(dev_name(codec->dev));
+#endif
 
 		pm_wakeup_event(codec->dev, 300);