| config MAC80211 |
| tristate "Generic IEEE 802.11 Networking Stack (mac80211)" |
| select CRYPTO |
| select CRYPTO_ECB |
| select CRYPTO_ARC4 |
| select CRYPTO_AES |
| select CRC32 |
| select WIRELESS_EXT |
| select CFG80211 |
| ---help--- |
| This option enables the hardware independent IEEE 802.11 |
| networking stack. |
| |
| config MAC80211_QOS |
| def_bool y |
| depends on MAC80211 |
| depends on NET_SCHED |
| depends on NETDEVICES_MULTIQUEUE |
| |
| comment "QoS/HT support disabled" |
| depends on MAC80211 && !MAC80211_QOS |
| comment "QoS/HT support needs CONFIG_NET_SCHED" |
| depends on MAC80211 && !NET_SCHED |
| comment "QoS/HT support needs CONFIG_NETDEVICES_MULTIQUEUE" |
| depends on MAC80211 && !NETDEVICES_MULTIQUEUE |
| |
| menu "Rate control algorithm selection" |
| depends on MAC80211 != n |
| |
| choice |
| prompt "Default rate control algorithm" |
| default MAC80211_RC_DEFAULT_PID |
| ---help--- |
| This option selects the default rate control algorithm |
| mac80211 will use. Note that this default can still be |
| overriden through the ieee80211_default_rc_algo module |
| parameter if different algorithms are available. |
| |
| config MAC80211_RC_DEFAULT_PID |
| bool "PID controller based rate control algorithm" |
| select MAC80211_RC_PID |
| ---help--- |
| Select the PID controller based rate control as the |
| default rate control algorithm. You should choose |
| this unless you know what you are doing. |
| |
| config MAC80211_RC_DEFAULT_NONE |
| bool "No default algorithm" |
| depends on EMBEDDED |
| help |
| Selecting this option will select no default algorithm |
| and allow you to not build any. Do not choose this |
| option unless you know your driver comes with another |
| suitable algorithm. |
| endchoice |
| |
| comment "Selecting 'y' for an algorithm will" |
| comment "build the algorithm into mac80211." |
| |
| config MAC80211_RC_DEFAULT |
| string |
| default "pid" if MAC80211_RC_DEFAULT_PID |
| default "" |
| |
| config MAC80211_RC_PID |
| tristate "PID controller based rate control algorithm" |
| ---help--- |
| This option enables a TX rate control algorithm for |
| mac80211 that uses a PID controller to select the TX |
| rate. |
| |
| Say Y or M unless you're sure you want to use a |
| different rate control algorithm. |
| |
| endmenu |
| |
| config MAC80211_MESH |
| bool "Enable mac80211 mesh networking (pre-802.11s) support" |
| depends on MAC80211 && EXPERIMENTAL |
| ---help--- |
| This options enables support of Draft 802.11s mesh networking. |
| The implementation is based on Draft 1.08 of the Mesh Networking |
| amendment. For more information visit http://o11s.org/. |
| |
| |
| config MAC80211_LEDS |
| bool "Enable LED triggers" |
| depends on MAC80211 |
| select NEW_LEDS |
| select LEDS_TRIGGERS |
| ---help--- |
| This option enables a few LED triggers for different |
| packet receive/transmit events. |
| |
| config MAC80211_DEBUGFS |
| bool "Export mac80211 internals in DebugFS" |
| depends on MAC80211 && DEBUG_FS |
| ---help--- |
| Select this to see extensive information about |
| the internal state of mac80211 in debugfs. |
| |
| Say N unless you know you need this. |
| |
| config MAC80211_DEBUG_PACKET_ALIGNMENT |
| bool "Enable packet alignment debugging" |
| depends on MAC80211 |
| help |
| This option is recommended for driver authors and strongly |
| discouraged for everybody else, it will trigger a warning |
| when a driver hands mac80211 a buffer that is aligned in |
| a way that will cause problems with the IP stack on some |
| architectures. |
| |
| Say N unless you're writing a mac80211 based driver. |
| |
| config MAC80211_DEBUG |
| bool "Enable debugging output" |
| depends on MAC80211 |
| ---help--- |
| This option will enable debug tracing output for the |
| ieee80211 network stack. |
| |
| If you are not trying to debug or develop the ieee80211 |
| subsystem, you most likely want to say N here. |
| |
| config MAC80211_HT_DEBUG |
| bool "Enable HT debugging output" |
| depends on MAC80211_DEBUG |
| ---help--- |
| This option enables 802.11n High Throughput features |
| debug tracing output. |
| |
| If you are not trying to debug of develop the ieee80211 |
| subsystem, you most likely want to say N here. |
| |
| config MAC80211_VERBOSE_DEBUG |
| bool "Verbose debugging output" |
| depends on MAC80211_DEBUG |
| |
| config MAC80211_LOWTX_FRAME_DUMP |
| bool "Debug frame dumping" |
| depends on MAC80211_DEBUG |
| ---help--- |
| Selecting this option will cause the stack to |
| print a message for each frame that is handed |
| to the lowlevel driver for transmission. This |
| message includes all MAC addresses and the |
| frame control field. |
| |
| If unsure, say N and insert the debugging code |
| you require into the driver you are debugging. |
| |
| config TKIP_DEBUG |
| bool "TKIP debugging" |
| depends on MAC80211_DEBUG |
| |
| config MAC80211_DEBUG_COUNTERS |
| bool "Extra statistics for TX/RX debugging" |
| depends on MAC80211_DEBUG |
| |
| config MAC80211_IBSS_DEBUG |
| bool "Support for IBSS testing" |
| depends on MAC80211_DEBUG |
| ---help--- |
| Say Y here if you intend to debug the IBSS code. |
| |
| config MAC80211_VERBOSE_PS_DEBUG |
| bool "Verbose powersave mode debugging" |
| depends on MAC80211_DEBUG |
| ---help--- |
| Say Y here to print out verbose powersave |
| mode debug messages. |
| |
| config MAC80211_VERBOSE_MPL_DEBUG |
| bool "Verbose mesh peer link debugging" |
| depends on MAC80211_DEBUG && MAC80211_MESH |
| ---help--- |
| Say Y here to print out verbose mesh peer link |
| debug messages. |