/* Copyright (c) 2013, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/dts-v1/;
/include/ "msm8226.dtsi"
/include/ "dsi-panel-nt35590-720p-video.dtsi"
/include/ "msm8226-camera-sensor-cdp.dtsi"

/ {
	model = "Qualcomm MSM 8226 CDP";
	compatible = "qcom,msm8226-cdp", "qcom,msm8226", "qcom,cdp";
	qcom,msm-id = <145 1 0>,
		      <158 1 0>,
		      <159 1 0>,
		      <198 1 0>;
};

&soc {
	serial@f991f000 {
		status = "ok";
	};

	qcom,mdss_dsi_nt35590_720p_video {
		status = "ok";
	};

	i2c@f9927000 { /* BLSP1 QUP5 */
		synaptics@20 {
			compatible = "synaptics,rmi4";
			reg = <0x20>;
			interrupt-parent = <&msmgpio>;
			interrupts = <17 0x2008>;
			vdd-supply = <&pm8226_l19>;
			vcc_i2c-supply = <&pm8226_lvs1>;
			synaptics,reset-gpio = <&msmgpio 16 0x00>;
			synaptics,irq-gpio = <&msmgpio 17 0x2008>;
			synaptics,button-map = <139 102 158>;
			synaptics,i2c-pull-up;
			synaptics,reg-en;
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		input-name = "gpio-keys";

		camera_focus {
			label = "camera_focus";
			gpios = <&msmgpio 108 0x1>;
			linux,input-type = <1>;
			linux,code = <0x210>;
			gpio-key,wakeup;
			debounce-interval = <15>;
		};

		camera_snapshot {
			label = "camera_snapshot";
			gpios = <&msmgpio 107 0x1>;
			linux,input-type = <1>;
			linux,code = <0x2fe>;
			gpio-key,wakeup;
			debounce-interval = <15>;
		};

		vol_up {
			label = "volume_up";
			gpios = <&msmgpio 106 0x1>;
			linux,input-type = <1>;
			linux,code = <115>;
			gpio-key,wakeup;
			debounce-interval = <15>;
		};
	};

	spi@f9923000 {
		ethernet-switch@3 {
			compatible = "micrel,ks8851";
			reg = <3>;
			interrupt-parent = <&msmgpio>;
			interrupts = <0 115 0>;
			spi-max-frequency = <4800000>;
			rst-gpio = <&msmgpio 114 0>;
			vdd-io-supply = <&pm8226_lvs1>;
			vdd-phy-supply = <&pm8226_lvs1>;
		};
	};

	sound {
		qcom,audio-routing =
			"RX_BIAS", "MCLK",
			"LDO_H", "MCLK",
			"SPK_OUT", "MCLK",
			"SPK_OUT", "EXT_VDD_SPKR",
			"AMIC1", "MIC BIAS1 Internal1",
			"MIC BIAS1 Internal1", "Handset Mic",
			"AMIC2", "MIC BIAS2 External",
			"MIC BIAS2 External", "Headset Mic",
			"AMIC4", "MIC BIAS2 External",
			"MIC BIAS2 External", "ANCRight Headset Mic",
			"AMIC5", "MIC BIAS2 External",
			"MIC BIAS2 External", "ANCLeft Headset Mic",
			"DMIC1", "MIC BIAS1 External",
			"MIC BIAS1 External", "Digital Mic1",
			"DMIC2", "MIC BIAS1 External",
			"MIC BIAS1 External", "Digital Mic2",
			"DMIC3", "MIC BIAS3 External",
			"MIC BIAS3 External", "Digital Mic3",
			"DMIC4", "MIC BIAS3 External",
			"MIC BIAS3 External", "Digital Mic4";

		qcom,cdc-mclk-gpios = <&pm8226_gpios 1 0>;
		qcom,cdc-vdd-spkr-gpios = <&pm8226_gpios 2 0>;
		qcom,headset-jack-type-NO;
	};
};

&sdcc1 {
	vdd-supply = <&pm8226_l17>;
	qcom,vdd-always-on;
	qcom,vdd-lpm-sup;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <800 500000>;

	vdd-io-supply = <&pm8226_l6>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-voltage-level = <1800000 1800000>;
	qcom,vdd-io-current-level = <250 154000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

	qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
	qcom,sup-voltages = <2950 2950>;

	qcom,bus-speed-mode = "HS200_1p8v", "DDR_1p8v";
	qcom,nonremovable;

	status = "disabled";
};

&sdhc_1 {
	vdd-supply = <&pm8226_l17>;
	qcom,vdd-always-on;
	qcom,vdd-lpm-sup;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <800 500000>;

	vdd-io-supply = <&pm8226_l6>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-voltage-level = <1800000 1800000>;
	qcom,vdd-io-current-level = <250 154000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

	qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
	qcom,bus-speed-mode = "HS200_1p8v", "DDR_1p8v";
	qcom,nonremovable;

	status = "ok";
};

&sdcc2 {
	vdd-supply = <&pm8226_l18>;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <9000 800000>;

	vdd-io-supply = <&pm8226_l21>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-lpm-sup;
	qcom,vdd-io-voltage-level = <1800000 2950000>;
	qcom,vdd-io-current-level = <6 22000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

	qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
	qcom,sup-voltages = <2950 2950>;

	qcom,xpc;
	qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50", "DDR50", "SDR104";
	qcom,current-limit = <600>;

	#address-cells = <0>;
	interrupt-parent = <&sdcc2>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 125 0
			1 &intc 0 220 0
			2 &msmgpio 38 0x3>;
	interrupt-names = "core_irq", "bam_irq", "status_irq";
	cd-gpios = <&msmgpio 38 0x1>;

	status = "disabled";
};

&sdhc_2 {
	vdd-supply = <&pm8226_l18>;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <9000 800000>;

	vdd-io-supply = <&pm8226_l21>;
	qcom,vdd-io-always-on;
	qcom,vdd-io-lpm-sup;
	qcom,vdd-io-voltage-level = <1800000 2950000>;
	qcom,vdd-io-current-level = <6 22000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

	qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;

	#address-cells = <0>;
	interrupt-parent = <&sdhc_2>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 125 0
			1 &intc 0 221 0
			2 &msmgpio 38 0x3>;
	interrupt-names = "hc_irq", "pwr_irq", "status_irq";
	cd-gpios = <&msmgpio 38 0x1>;

	status = "ok";
};

&spmi_bus {
	qcom,pm8226@0 {
		qcom,leds@a100 {
			status = "okay";
			qcom,led_mpp_2 {
				label = "mpp";
				linux,name = "button-backlight";
				linux,default-trigger = "none";
				qcom,default-state = "off";
				qcom,max-current = <40>;
				qcom,current-setting = <5>;
				qcom,id = <6>;
				qcom,mode = <2>;
				qcom,source-sel = <1>;
				qcom,mode-ctrl = <0x60>;
			};
		};
	};

	qcom,pm8226@1 {
		qcom,leds@d800 {
			status = "okay";
			qcom,wled_0 {
				label = "wled";
				linux,name = "wled:backlight";
				linux,default-trigger = "bkl-trigger";
				qcom,cs-out-en;
				qcom,op-fdbck = <1>;
				qcom,default-state = "on";
				qcom,max-current = <25>;
				qcom,ctrl-delay-us = <0>;
				qcom,boost-curr-lim = <3>;
				qcom,cp-sel = <0>;
				qcom,switch-freq = <2>;
				qcom,ovp-val = <0>;
				qcom,num-strings = <1>;
				qcom,id = <0>;
			};
		};
	};
};

&pm8226_gpios {
	gpio@c000 { /* GPIO 1 */
		/* XO_PMIC_CDC_MCLK enable for tapan codec */
		qcom,mode = <1>;		/* Digital output */
		qcom,output-type = <0>;	/* CMOS logic */
		qcom,pull = <5>;		/* QPNP_PIN_PULL_NO*/
		qcom,vin-sel = <3>;		/* QPNP_PIN_VIN3 */
		qcom,out-strength = <3>;/* QPNP_PIN_OUT_STRENGTH_HIGH */
		qcom,src-sel = <2>;		/* QPNP_PIN_SEL_FUNC_1 */
		qcom,master-en = <1>;	/* Enable GPIO */
	};

	gpio@c100 { /* GPIO 2 */
		qcom,mode = <1>;
		qcom,output-type = <0>;
		qcom,pull = <5>;
		qcom,vin-sel = <3>;
		qcom,out-strength = <3>;
		qcom,src-sel = <2>;
		qcom,master-en = <1>;
	};

	gpio@c200 { /* GPIO 3 */
	};

	gpio@c300 { /* GPIO 4 */
	};

	gpio@c400 { /* GPIO 5 */
	};

	gpio@c500 { /* GPIO 6 */
	};

	gpio@c600 { /* GPIO 7 */
	};

	gpio@c700 { /* GPIO 8 */
	};
};

&pm8226_mpps {
	mpp@a000 { /* MPP 1 */
	};

	mpp@a100 { /* MPP 2 */
	};

	mpp@a200 { /* MPP 3 */
	};

	mpp@a300 { /* MPP 4 */
	};

	mpp@a400 { /* MPP 5 */
	};

	mpp@a500 { /* MPP 6 */
	};

	mpp@a600 { /* MPP 7 */
	};

	mpp@a700 { /* MPP 8 */
	};
};

&pm8226_chg {
	qcom,charging-disabled;
	qcom,use-default-batt-values;
};