Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/net/3c505.h b/drivers/net/3c505.h
new file mode 100644
index 0000000..77dfeed
--- /dev/null
+++ b/drivers/net/3c505.h
@@ -0,0 +1,293 @@
+/*****************************************************************
+ *
+ * defines for 3Com Etherlink Plus adapter
+ *
+ *****************************************************************/
+
+#define ELP_DMA 6
+#define ELP_RX_PCBS 4
+#define ELP_MAX_CARDS 4
+
+/*
+ * I/O register offsets
+ */
+#define PORT_COMMAND 0x00 /* read/write, 8-bit */
+#define PORT_STATUS 0x02 /* read only, 8-bit */
+#define PORT_AUXDMA 0x02 /* write only, 8-bit */
+#define PORT_DATA 0x04 /* read/write, 16-bit */
+#define PORT_CONTROL 0x06 /* read/write, 8-bit */
+
+#define ELP_IO_EXTENT 0x10 /* size of used IO registers */
+
+/*
+ * host control registers bits
+ */
+#define ATTN 0x80 /* attention */
+#define FLSH 0x40 /* flush data register */
+#define DMAE 0x20 /* DMA enable */
+#define DIR 0x10 /* direction */
+#define TCEN 0x08 /* terminal count interrupt enable */
+#define CMDE 0x04 /* command register interrupt enable */
+#define HSF2 0x02 /* host status flag 2 */
+#define HSF1 0x01 /* host status flag 1 */
+
+/*
+ * combinations of HSF flags used for PCB transmission
+ */
+#define HSF_PCB_ACK HSF1
+#define HSF_PCB_NAK HSF2
+#define HSF_PCB_END (HSF2|HSF1)
+#define HSF_PCB_MASK (HSF2|HSF1)
+
+/*
+ * host status register bits
+ */
+#define HRDY 0x80 /* data register ready */
+#define HCRE 0x40 /* command register empty */
+#define ACRF 0x20 /* adapter command register full */
+/* #define DIR 0x10 direction - same as in control register */
+#define DONE 0x08 /* DMA done */
+#define ASF3 0x04 /* adapter status flag 3 */
+#define ASF2 0x02 /* adapter status flag 2 */
+#define ASF1 0x01 /* adapter status flag 1 */
+
+/*
+ * combinations of ASF flags used for PCB reception
+ */
+#define ASF_PCB_ACK ASF1
+#define ASF_PCB_NAK ASF2
+#define ASF_PCB_END (ASF2|ASF1)
+#define ASF_PCB_MASK (ASF2|ASF1)
+
+/*
+ * host aux DMA register bits
+ */
+#define DMA_BRST 0x01 /* DMA burst */
+
+/*
+ * maximum amount of data allowed in a PCB
+ */
+#define MAX_PCB_DATA 62
+
+/*****************************************************************
+ *
+ * timeout value
+ * this is a rough value used for loops to stop them from
+ * locking up the whole machine in the case of failure or
+ * error conditions
+ *
+ *****************************************************************/
+
+#define TIMEOUT 300
+
+/*****************************************************************
+ *
+ * PCB commands
+ *
+ *****************************************************************/
+
+enum {
+ /*
+ * host PCB commands
+ */
+ CMD_CONFIGURE_ADAPTER_MEMORY = 0x01,
+ CMD_CONFIGURE_82586 = 0x02,
+ CMD_STATION_ADDRESS = 0x03,
+ CMD_DMA_DOWNLOAD = 0x04,
+ CMD_DMA_UPLOAD = 0x05,
+ CMD_PIO_DOWNLOAD = 0x06,
+ CMD_PIO_UPLOAD = 0x07,
+ CMD_RECEIVE_PACKET = 0x08,
+ CMD_TRANSMIT_PACKET = 0x09,
+ CMD_NETWORK_STATISTICS = 0x0a,
+ CMD_LOAD_MULTICAST_LIST = 0x0b,
+ CMD_CLEAR_PROGRAM = 0x0c,
+ CMD_DOWNLOAD_PROGRAM = 0x0d,
+ CMD_EXECUTE_PROGRAM = 0x0e,
+ CMD_SELF_TEST = 0x0f,
+ CMD_SET_STATION_ADDRESS = 0x10,
+ CMD_ADAPTER_INFO = 0x11,
+ NUM_TRANSMIT_CMDS,
+
+ /*
+ * adapter PCB commands
+ */
+ CMD_CONFIGURE_ADAPTER_RESPONSE = 0x31,
+ CMD_CONFIGURE_82586_RESPONSE = 0x32,
+ CMD_ADDRESS_RESPONSE = 0x33,
+ CMD_DOWNLOAD_DATA_REQUEST = 0x34,
+ CMD_UPLOAD_DATA_REQUEST = 0x35,
+ CMD_RECEIVE_PACKET_COMPLETE = 0x38,
+ CMD_TRANSMIT_PACKET_COMPLETE = 0x39,
+ CMD_NETWORK_STATISTICS_RESPONSE = 0x3a,
+ CMD_LOAD_MULTICAST_RESPONSE = 0x3b,
+ CMD_CLEAR_PROGRAM_RESPONSE = 0x3c,
+ CMD_DOWNLOAD_PROGRAM_RESPONSE = 0x3d,
+ CMD_EXECUTE_RESPONSE = 0x3e,
+ CMD_SELF_TEST_RESPONSE = 0x3f,
+ CMD_SET_ADDRESS_RESPONSE = 0x40,
+ CMD_ADAPTER_INFO_RESPONSE = 0x41
+};
+
+/* Definitions for the PCB data structure */
+
+/* Data units */
+typedef unsigned char byte;
+typedef unsigned short int word;
+typedef unsigned long int dword;
+
+/* Data structures */
+struct Memconf {
+ word cmd_q,
+ rcv_q,
+ mcast,
+ frame,
+ rcv_b,
+ progs;
+};
+
+struct Rcv_pkt {
+ word buf_ofs,
+ buf_seg,
+ buf_len,
+ timeout;
+};
+
+struct Xmit_pkt {
+ word buf_ofs,
+ buf_seg,
+ pkt_len;
+};
+
+struct Rcv_resp {
+ word buf_ofs,
+ buf_seg,
+ buf_len,
+ pkt_len,
+ timeout,
+ status;
+ dword timetag;
+};
+
+struct Xmit_resp {
+ word buf_ofs,
+ buf_seg,
+ c_stat,
+ status;
+};
+
+
+struct Netstat {
+ dword tot_recv,
+ tot_xmit;
+ word err_CRC,
+ err_align,
+ err_res,
+ err_ovrrun;
+};
+
+
+struct Selftest {
+ word error;
+ union {
+ word ROM_cksum;
+ struct {
+ word ofs, seg;
+ } RAM;
+ word i82586;
+ } failure;
+};
+
+struct Info {
+ byte minor_vers,
+ major_vers;
+ word ROM_cksum,
+ RAM_sz,
+ free_ofs,
+ free_seg;
+};
+
+struct Memdump {
+ word size,
+ off,
+ seg;
+};
+
+/*
+Primary Command Block. The most important data structure. All communication
+between the host and the adapter is done with these. (Except for the actual
+Ethernet data, which has different packaging.)
+*/
+typedef struct {
+ byte command;
+ byte length;
+ union {
+ struct Memconf memconf;
+ word configure;
+ struct Rcv_pkt rcv_pkt;
+ struct Xmit_pkt xmit_pkt;
+ byte multicast[10][6];
+ byte eth_addr[6];
+ byte failed;
+ struct Rcv_resp rcv_resp;
+ struct Xmit_resp xmit_resp;
+ struct Netstat netstat;
+ struct Selftest selftest;
+ struct Info info;
+ struct Memdump memdump;
+ byte raw[62];
+ } data;
+} pcb_struct;
+
+/* These defines for 'configure' */
+#define RECV_STATION 0x00
+#define RECV_BROAD 0x01
+#define RECV_MULTI 0x02
+#define RECV_PROMISC 0x04
+#define NO_LOOPBACK 0x00
+#define INT_LOOPBACK 0x08
+#define EXT_LOOPBACK 0x10
+
+/*****************************************************************
+ *
+ * structure to hold context information for adapter
+ *
+ *****************************************************************/
+
+#define DMA_BUFFER_SIZE 1600
+#define BACKLOG_SIZE 4
+
+typedef struct {
+ volatile short got[NUM_TRANSMIT_CMDS]; /* flags for
+ command completion */
+ pcb_struct tx_pcb; /* PCB for foreground sending */
+ pcb_struct rx_pcb; /* PCB for foreground receiving */
+ pcb_struct itx_pcb; /* PCB for background sending */
+ pcb_struct irx_pcb; /* PCB for background receiving */
+ struct net_device_stats stats;
+
+ void *dma_buffer;
+
+ struct {
+ unsigned int length[BACKLOG_SIZE];
+ unsigned int in;
+ unsigned int out;
+ } rx_backlog;
+
+ struct {
+ unsigned int direction;
+ unsigned int length;
+ struct sk_buff *skb;
+ void *target;
+ unsigned long start_time;
+ } current_dma;
+
+ /* flags */
+ unsigned long send_pcb_semaphore;
+ unsigned long dmaing;
+ unsigned long busy;
+
+ unsigned int rx_active; /* number of receive PCBs */
+ volatile unsigned char hcr_val; /* what we think the HCR contains */
+ spinlock_t lock; /* Interrupt v tx lock */
+} elp_device;