mac80211: fix wext bssid/ssid setting
When changing to a new BSSID or SSID, the code in
ieee80211_set_disassoc() needs to have the old data
still valid to be able to disconnect and clean up
properly. Currently, however, the old data is thrown
away before ieee80211_set_disassoc() is ever called,
so fix that by calling the function _before_ the old
data is overwritten.
This is (one of) the issue(s) causing mac80211 to hold
cfg80211's BSS structs forever, and them thus being
returned in scan results after they're long gone.
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2015
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index 84e59b9..aca22b0 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -1102,14 +1102,6 @@
struct sta_info *sta;
u32 changed = 0, config_changed = 0;
- rcu_read_lock();
-
- sta = sta_info_get(local, ifmgd->bssid);
- if (!sta) {
- rcu_read_unlock();
- return;
- }
-
if (deauth) {
ifmgd->direct_probe_tries = 0;
ifmgd->auth_tries = 0;
@@ -1120,7 +1112,11 @@
netif_tx_stop_all_queues(sdata->dev);
netif_carrier_off(sdata->dev);
- ieee80211_sta_tear_down_BA_sessions(sta);
+ rcu_read_lock();
+ sta = sta_info_get(local, ifmgd->bssid);
+ if (sta)
+ ieee80211_sta_tear_down_BA_sessions(sta);
+ rcu_read_unlock();
bss = ieee80211_rx_bss_get(local, ifmgd->bssid,
conf->channel->center_freq,
@@ -1156,8 +1152,6 @@
ifmgd->ssid, ifmgd->ssid_len);
}
- rcu_read_unlock();
-
ieee80211_set_wmm_default(sdata);
ieee80211_recalc_idle(local);
@@ -2487,6 +2481,10 @@
ifmgd = &sdata->u.mgd;
if (ifmgd->ssid_len != len || memcmp(ifmgd->ssid, ssid, len) != 0) {
+ if (ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+ ieee80211_set_disassoc(sdata, true, true,
+ WLAN_REASON_DEAUTH_LEAVING);
+
/*
* Do not use reassociation if SSID is changed (different ESS).
*/
@@ -2511,6 +2509,11 @@
{
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
+ if (compare_ether_addr(bssid, ifmgd->bssid) != 0 &&
+ ifmgd->state == IEEE80211_STA_MLME_ASSOCIATED)
+ ieee80211_set_disassoc(sdata, true, true,
+ WLAN_REASON_DEAUTH_LEAVING);
+
if (is_valid_ether_addr(bssid)) {
memcpy(ifmgd->bssid, bssid, ETH_ALEN);
ifmgd->flags |= IEEE80211_STA_BSSID_SET;