[SCSI] fusion : mpi header update
MPI Header Update
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/message/fusion/lsi/fc_log.h b/drivers/message/fusion/lsi/fc_log.h
deleted file mode 100644
index dc98d46..0000000
--- a/drivers/message/fusion/lsi/fc_log.h
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * Copyright (c) 2000-2001 LSI Logic Corporation. All rights reserved.
- *
- * NAME: fc_log.h
- * SUMMARY: MPI IocLogInfo definitions for the SYMFC9xx chips
- * DESCRIPTION: Contains the enumerated list of values that may be returned
- * in the IOCLogInfo field of a MPI Default Reply Message.
- *
- * CREATION DATE: 6/02/2000
- * ID: $Id: fc_log.h,v 4.6 2001/07/26 14:41:33 sschremm Exp $
- */
-
-
-/*
- * MpiIocLogInfo_t enum
- *
- * These 32 bit values are used in the IOCLogInfo field of the MPI reply
- * messages.
- * The value is 0xabcccccc where
- * a = The type of log info as per the MPI spec. Since these codes are
- * all for Fibre Channel this value will always be 2.
- * b = Specifies a subclass of the firmware where
- * 0 = FCP Initiator
- * 1 = FCP Target
- * 2 = LAN
- * 3 = MPI Message Layer
- * 4 = FC Link
- * 5 = Context Manager
- * 6 = Invalid Field Offset
- * 7 = State Change Info
- * all others are reserved for future use
- * c = A specific value within the subclass.
- *
- * NOTE: Any new values should be added to the end of each subclass so that the
- * codes remain consistent across firmware releases.
- */
-typedef enum _MpiIocLogInfoFc
-{
- MPI_IOCLOGINFO_FC_INIT_BASE = 0x20000000,
- MPI_IOCLOGINFO_FC_INIT_ERROR_OUT_OF_ORDER_FRAME = 0x20000001, /* received an out of order frame - unsupported */
- MPI_IOCLOGINFO_FC_INIT_ERROR_BAD_START_OF_FRAME = 0x20000002, /* Bad Rx Frame, bad start of frame primative */
- MPI_IOCLOGINFO_FC_INIT_ERROR_BAD_END_OF_FRAME = 0x20000003, /* Bad Rx Frame, bad end of frame primative */
- MPI_IOCLOGINFO_FC_INIT_ERROR_OVER_RUN = 0x20000004, /* Bad Rx Frame, overrun */
- MPI_IOCLOGINFO_FC_INIT_ERROR_RX_OTHER = 0x20000005, /* Other errors caught by IOC which require retries */
- MPI_IOCLOGINFO_FC_INIT_ERROR_SUBPROC_DEAD = 0x20000006, /* Main processor could not initialize sub-processor */
- MPI_IOCLOGINFO_FC_INIT_ERROR_RX_OVERRUN = 0x20000007, /* Scatter Gather overrun */
- MPI_IOCLOGINFO_FC_INIT_ERROR_RX_BAD_STATUS = 0x20000008, /* Receiver detected context mismatch via invalid header */
- MPI_IOCLOGINFO_FC_INIT_ERROR_RX_UNEXPECTED_FRAME= 0x20000009, /* CtxMgr detected unsupported frame type */
- MPI_IOCLOGINFO_FC_INIT_ERROR_LINK_FAILURE = 0x2000000A, /* Link failure occurred */
- MPI_IOCLOGINFO_FC_INIT_ERROR_TX_TIMEOUT = 0x2000000B, /* Transmitter timeout error */
-
- MPI_IOCLOGINFO_FC_TARGET_BASE = 0x21000000,
- MPI_IOCLOGINFO_FC_TARGET_NO_PDISC = 0x21000001, /* not sent because we are waiting for a PDISC from the initiator */
- MPI_IOCLOGINFO_FC_TARGET_NO_LOGIN = 0x21000002, /* not sent because we are not logged in to the remote node */
- MPI_IOCLOGINFO_FC_TARGET_DOAR_KILLED_BY_LIP = 0x21000003, /* Data Out, Auto Response, not sent due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_DIAR_KILLED_BY_LIP = 0x21000004, /* Data In, Auto Response, not sent due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_DIAR_MISSING_DATA = 0x21000005, /* Data In, Auto Response, missing data frames */
- MPI_IOCLOGINFO_FC_TARGET_DONR_KILLED_BY_LIP = 0x21000006, /* Data Out, No Response, not sent due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_WRSP_KILLED_BY_LIP = 0x21000007, /* Auto-response after a write not sent due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_DINR_KILLED_BY_LIP = 0x21000008, /* Data In, No Response, not completed due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_DINR_MISSING_DATA = 0x21000009, /* Data In, No Response, missing data frames */
- MPI_IOCLOGINFO_FC_TARGET_MRSP_KILLED_BY_LIP = 0x2100000a, /* Manual Response not sent due to a LIP */
- MPI_IOCLOGINFO_FC_TARGET_NO_CLASS_3 = 0x2100000b, /* not sent because remote node does not support Class 3 */
- MPI_IOCLOGINFO_FC_TARGET_LOGIN_NOT_VALID = 0x2100000c, /* not sent because login to remote node not validated */
- MPI_IOCLOGINFO_FC_TARGET_FROM_OUTBOUND = 0x2100000e, /* cleared from the outbound queue after a logout */
- MPI_IOCLOGINFO_FC_TARGET_WAITING_FOR_DATA_IN = 0x2100000f, /* cleared waiting for data after a logout */
-
- MPI_IOCLOGINFO_FC_LAN_BASE = 0x22000000,
- MPI_IOCLOGINFO_FC_LAN_TRANS_SGL_MISSING = 0x22000001, /* Transaction Context Sgl Missing */
- MPI_IOCLOGINFO_FC_LAN_TRANS_WRONG_PLACE = 0x22000002, /* Transaction Context found before an EOB */
- MPI_IOCLOGINFO_FC_LAN_TRANS_RES_BITS_SET = 0x22000003, /* Transaction Context value has reserved bits set */
- MPI_IOCLOGINFO_FC_LAN_WRONG_SGL_FLAG = 0x22000004, /* Invalid SGL Flags */
-
- MPI_IOCLOGINFO_FC_MSG_BASE = 0x23000000,
-
- MPI_IOCLOGINFO_FC_LINK_BASE = 0x24000000,
- MPI_IOCLOGINFO_FC_LINK_LOOP_INIT_TIMEOUT = 0x24000001, /* Loop initialization timed out */
- MPI_IOCLOGINFO_FC_LINK_ALREADY_INITIALIZED = 0x24000002, /* Another system controller already initialized the loop */
- MPI_IOCLOGINFO_FC_LINK_LINK_NOT_ESTABLISHED = 0x24000003, /* Not synchronized to signal or still negotiating (possible cable problem) */
- MPI_IOCLOGINFO_FC_LINK_CRC_ERROR = 0x24000004, /* CRC check detected error on received frame */
-
- MPI_IOCLOGINFO_FC_CTX_BASE = 0x25000000,
-
- MPI_IOCLOGINFO_FC_INVALID_FIELD_BYTE_OFFSET = 0x26000000, /* The lower 24 bits give the byte offset of the field in the request message that is invalid */
- MPI_IOCLOGINFO_FC_INVALID_FIELD_MAX_OFFSET = 0x26ffffff,
-
- MPI_IOCLOGINFO_FC_STATE_CHANGE = 0x27000000 /* The lower 24 bits give additional information concerning state change */
-
-} MpiIocLogInfoFc_t;
diff --git a/drivers/message/fusion/lsi/mpi.h b/drivers/message/fusion/lsi/mpi.h
index 02cdc84..81ad776 100644
--- a/drivers/message/fusion/lsi/mpi.h
+++ b/drivers/message/fusion/lsi/mpi.h
@@ -6,7 +6,7 @@
* Title: MPI Message independent structures and definitions
* Creation Date: July 27, 2000
*
- * mpi.h Version: 01.05.10
+ * mpi.h Version: 01.05.11
*
* Version History
* ---------------
@@ -76,6 +76,7 @@
* Added EEDP IOCStatus codes.
* 08-03-05 01.05.09 Bumped MPI_HEADER_VERSION_UNIT.
* 08-30-05 01.05.10 Added 2 new IOCStatus codes for Target.
+ * 03-27-06 01.05.11 Bumped MPI_HEADER_VERSION_UNIT.
* --------------------------------------------------------------------------
*/
@@ -106,7 +107,7 @@
/* Note: The major versions of 0xe0 through 0xff are reserved */
/* versioning for this MPI header set */
-#define MPI_HEADER_VERSION_UNIT (0x0C)
+#define MPI_HEADER_VERSION_UNIT (0x0D)
#define MPI_HEADER_VERSION_DEV (0x00)
#define MPI_HEADER_VERSION_UNIT_MASK (0xFF00)
#define MPI_HEADER_VERSION_UNIT_SHIFT (8)
diff --git a/drivers/message/fusion/lsi/mpi_cnfg.h b/drivers/message/fusion/lsi/mpi_cnfg.h
index b1becec..47e13e3 100644
--- a/drivers/message/fusion/lsi/mpi_cnfg.h
+++ b/drivers/message/fusion/lsi/mpi_cnfg.h
@@ -6,7 +6,7 @@
* Title: MPI Config message, structures, and Pages
* Creation Date: July 27, 2000
*
- * mpi_cnfg.h Version: 01.05.11
+ * mpi_cnfg.h Version: 01.05.12
*
* Version History
* ---------------
@@ -266,6 +266,16 @@
* Added postpone SATA Init bit to SAS IO Unit Page 1
* ControlFlags.
* Changed LogEntry format for Log Page 0.
+ * 03-27-06 01.05.12 Added two new Flags defines for Manufacturing Page 4.
+ * Added Manufacturing Page 7.
+ * Added MPI_IOCPAGE2_CAP_FLAGS_RAID_64_BIT_ADDRESSING.
+ * Added IOC Page 6.
+ * Added PrevBootDeviceForm field to CONFIG_PAGE_BIOS_2.
+ * Added MaxLBAHigh field to RAID Volume Page 0.
+ * Added Nvdata version fields to SAS IO Unit Page 0.
+ * Added AdditionalControlFlags, MaxTargetPortConnectTime,
+ * ReportDeviceMissingDelay, and IODeviceMissingDelay
+ * fields to SAS IO Unit Page 1.
* --------------------------------------------------------------------------
*/
@@ -631,9 +641,11 @@
} CONFIG_PAGE_MANUFACTURING_4, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_4,
ManufacturingPage4_t, MPI_POINTER pManufacturingPage4_t;
-#define MPI_MANUFACTURING4_PAGEVERSION (0x03)
+#define MPI_MANUFACTURING4_PAGEVERSION (0x04)
/* defines for the Flags field */
+#define MPI_MANPAGE4_FORCE_BAD_BLOCK_TABLE (0x80)
+#define MPI_MANPAGE4_FORCE_OFFLINE_FAILOVER (0x40)
#define MPI_MANPAGE4_IME_DISABLE (0x20)
#define MPI_MANPAGE4_IM_DISABLE (0x10)
#define MPI_MANPAGE4_IS_DISABLE (0x08)
@@ -668,6 +680,66 @@
#define MPI_MANUFACTURING6_PAGEVERSION (0x00)
+typedef struct _MPI_MANPAGE7_CONNECTOR_INFO
+{
+ U32 Pinout; /* 00h */
+ U8 Connector[16]; /* 04h */
+ U8 Location; /* 14h */
+ U8 Reserved1; /* 15h */
+ U16 Slot; /* 16h */
+ U32 Reserved2; /* 18h */
+} MPI_MANPAGE7_CONNECTOR_INFO, MPI_POINTER PTR_MPI_MANPAGE7_CONNECTOR_INFO,
+ MpiManPage7ConnectorInfo_t, MPI_POINTER pMpiManPage7ConnectorInfo_t;
+
+/* defines for the Pinout field */
+#define MPI_MANPAGE7_PINOUT_SFF_8484_L4 (0x00080000)
+#define MPI_MANPAGE7_PINOUT_SFF_8484_L3 (0x00040000)
+#define MPI_MANPAGE7_PINOUT_SFF_8484_L2 (0x00020000)
+#define MPI_MANPAGE7_PINOUT_SFF_8484_L1 (0x00010000)
+#define MPI_MANPAGE7_PINOUT_SFF_8470_L4 (0x00000800)
+#define MPI_MANPAGE7_PINOUT_SFF_8470_L3 (0x00000400)
+#define MPI_MANPAGE7_PINOUT_SFF_8470_L2 (0x00000200)
+#define MPI_MANPAGE7_PINOUT_SFF_8470_L1 (0x00000100)
+#define MPI_MANPAGE7_PINOUT_SFF_8482 (0x00000002)
+#define MPI_MANPAGE7_PINOUT_CONNECTION_UNKNOWN (0x00000001)
+
+/* defines for the Location field */
+#define MPI_MANPAGE7_LOCATION_UNKNOWN (0x01)
+#define MPI_MANPAGE7_LOCATION_INTERNAL (0x02)
+#define MPI_MANPAGE7_LOCATION_EXTERNAL (0x04)
+#define MPI_MANPAGE7_LOCATION_SWITCHABLE (0x08)
+#define MPI_MANPAGE7_LOCATION_AUTO (0x10)
+#define MPI_MANPAGE7_LOCATION_NOT_PRESENT (0x20)
+#define MPI_MANPAGE7_LOCATION_NOT_CONNECTED (0x80)
+
+/*
+ * Host code (drivers, BIOS, utilities, etc.) should leave this define set to
+ * one and check NumPhys at runtime.
+ */
+#ifndef MPI_MANPAGE7_CONNECTOR_INFO_MAX
+#define MPI_MANPAGE7_CONNECTOR_INFO_MAX (1)
+#endif
+
+typedef struct _CONFIG_PAGE_MANUFACTURING_7
+{
+ CONFIG_PAGE_HEADER Header; /* 00h */
+ U32 Reserved1; /* 04h */
+ U32 Reserved2; /* 08h */
+ U32 Flags; /* 0Ch */
+ U8 EnclosureName[16]; /* 10h */
+ U8 NumPhys; /* 20h */
+ U8 Reserved3; /* 21h */
+ U16 Reserved4; /* 22h */
+ MPI_MANPAGE7_CONNECTOR_INFO ConnectorInfo[MPI_MANPAGE7_CONNECTOR_INFO_MAX]; /* 24h */
+} CONFIG_PAGE_MANUFACTURING_7, MPI_POINTER PTR_CONFIG_PAGE_MANUFACTURING_7,
+ ManufacturingPage7_t, MPI_POINTER pManufacturingPage7_t;
+
+#define MPI_MANUFACTURING7_PAGEVERSION (0x00)
+
+/* defines for the Flags field */
+#define MPI_MANPAGE7_FLAG_USE_SLOT_INFO (0x00000001)
+
+
/****************************************************************************
* IO Unit Config Pages
****************************************************************************/
@@ -867,7 +939,7 @@
} CONFIG_PAGE_IOC_2, MPI_POINTER PTR_CONFIG_PAGE_IOC_2,
IOCPage2_t, MPI_POINTER pIOCPage2_t;
-#define MPI_IOCPAGE2_PAGEVERSION (0x03)
+#define MPI_IOCPAGE2_PAGEVERSION (0x04)
/* IOC Page 2 Capabilities flags */
@@ -878,6 +950,7 @@
#define MPI_IOCPAGE2_CAP_FLAGS_RAID_6_SUPPORT (0x00000010)
#define MPI_IOCPAGE2_CAP_FLAGS_RAID_10_SUPPORT (0x00000020)
#define MPI_IOCPAGE2_CAP_FLAGS_RAID_50_SUPPORT (0x00000040)
+#define MPI_IOCPAGE2_CAP_FLAGS_RAID_64_BIT_ADDRESSING (0x10000000)
#define MPI_IOCPAGE2_CAP_FLAGS_SES_SUPPORT (0x20000000)
#define MPI_IOCPAGE2_CAP_FLAGS_SAFTE_SUPPORT (0x40000000)
#define MPI_IOCPAGE2_CAP_FLAGS_CROSS_CHANNEL_SUPPORT (0x80000000)
@@ -975,6 +1048,44 @@
#define MPI_IOCPAGE5_PAGEVERSION (0x00)
+typedef struct _CONFIG_PAGE_IOC_6
+{
+ CONFIG_PAGE_HEADER Header; /* 00h */
+ U32 CapabilitiesFlags; /* 04h */
+ U8 MaxDrivesIS; /* 08h */
+ U8 MaxDrivesIM; /* 09h */
+ U8 MaxDrivesIME; /* 0Ah */
+ U8 Reserved1; /* 0Bh */
+ U8 MinDrivesIS; /* 0Ch */
+ U8 MinDrivesIM; /* 0Dh */
+ U8 MinDrivesIME; /* 0Eh */
+ U8 Reserved2; /* 0Fh */
+ U8 MaxGlobalHotSpares; /* 10h */
+ U8 Reserved3; /* 11h */
+ U16 Reserved4; /* 12h */
+ U32 Reserved5; /* 14h */
+ U32 SupportedStripeSizeMapIS; /* 18h */
+ U32 SupportedStripeSizeMapIME; /* 1Ch */
+ U32 Reserved6; /* 20h */
+ U8 MetadataSize; /* 24h */
+ U8 Reserved7; /* 25h */
+ U16 Reserved8; /* 26h */
+ U16 MaxBadBlockTableEntries; /* 28h */
+ U16 Reserved9; /* 2Ah */
+ U16 IRNvsramUsage; /* 2Ch */
+ U16 Reserved10; /* 2Eh */
+ U32 IRNvsramVersion; /* 30h */
+ U32 Reserved11; /* 34h */
+ U32 Reserved12; /* 38h */
+} CONFIG_PAGE_IOC_6, MPI_POINTER PTR_CONFIG_PAGE_IOC_6,
+ IOCPage6_t, MPI_POINTER pIOCPage6_t;
+
+#define MPI_IOCPAGE6_PAGEVERSION (0x00)
+
+/* IOC Page 6 Capabilities Flags */
+
+#define MPI_IOCPAGE6_CAP_FLAGS_GLOBAL_HOT_SPARE (0x00000001)
+
/****************************************************************************
* BIOS Config Pages
@@ -1218,13 +1329,13 @@
U32 Reserved5; /* 14h */
U32 Reserved6; /* 18h */
U8 BootDeviceForm; /* 1Ch */
- U8 Reserved7; /* 1Dh */
+ U8 PrevBootDeviceForm; /* 1Ch */
U16 Reserved8; /* 1Eh */
MPI_BIOSPAGE2_BOOT_DEVICE BootDevice; /* 20h */
} CONFIG_PAGE_BIOS_2, MPI_POINTER PTR_CONFIG_PAGE_BIOS_2,
BIOSPage2_t, MPI_POINTER pBIOSPage2_t;
-#define MPI_BIOSPAGE2_PAGEVERSION (0x01)
+#define MPI_BIOSPAGE2_PAGEVERSION (0x02)
#define MPI_BIOSPAGE2_FORM_MASK (0x0F)
#define MPI_BIOSPAGE2_FORM_ADAPTER_ORDER (0x00)
@@ -2080,7 +2191,7 @@
RAID_VOL0_STATUS VolumeStatus; /* 08h */
RAID_VOL0_SETTINGS VolumeSettings; /* 0Ch */
U32 MaxLBA; /* 10h */
- U32 Reserved1; /* 14h */
+ U32 MaxLBAHigh; /* 14h */
U32 StripeSize; /* 18h */
U32 Reserved2; /* 1Ch */
U32 Reserved3; /* 20h */
@@ -2092,7 +2203,7 @@
} CONFIG_PAGE_RAID_VOL_0, MPI_POINTER PTR_CONFIG_PAGE_RAID_VOL_0,
RaidVolumePage0_t, MPI_POINTER pRaidVolumePage0_t;
-#define MPI_RAIDVOLPAGE0_PAGEVERSION (0x05)
+#define MPI_RAIDVOLPAGE0_PAGEVERSION (0x06)
/* values for RAID Volume Page 0 InactiveStatus field */
#define MPI_RAIDVOLPAGE0_UNKNOWN_INACTIVE (0x00)
@@ -2324,7 +2435,8 @@
typedef struct _CONFIG_PAGE_SAS_IO_UNIT_0
{
CONFIG_EXTENDED_PAGE_HEADER Header; /* 00h */
- U32 Reserved1; /* 08h */
+ U16 NvdataVersionDefault; /* 08h */
+ U16 NvdataVersionPersistent; /* 0Ah */
U8 NumPhys; /* 0Ch */
U8 Reserved2; /* 0Dh */
U16 Reserved3; /* 0Eh */
@@ -2332,7 +2444,7 @@
} CONFIG_PAGE_SAS_IO_UNIT_0, MPI_POINTER PTR_CONFIG_PAGE_SAS_IO_UNIT_0,
SasIOUnitPage0_t, MPI_POINTER pSasIOUnitPage0_t;
-#define MPI_SASIOUNITPAGE0_PAGEVERSION (0x03)
+#define MPI_SASIOUNITPAGE0_PAGEVERSION (0x04)
/* values for SAS IO Unit Page 0 PortFlags */
#define MPI_SAS_IOUNIT0_PORT_FLAGS_DISCOVERY_IN_PROGRESS (0x08)
@@ -2373,12 +2485,13 @@
typedef struct _MPI_SAS_IO_UNIT1_PHY_DATA
{
- U8 Port; /* 00h */
- U8 PortFlags; /* 01h */
- U8 PhyFlags; /* 02h */
- U8 MaxMinLinkRate; /* 03h */
- U32 ControllerPhyDeviceInfo;/* 04h */
- U32 Reserved1; /* 08h */
+ U8 Port; /* 00h */
+ U8 PortFlags; /* 01h */
+ U8 PhyFlags; /* 02h */
+ U8 MaxMinLinkRate; /* 03h */
+ U32 ControllerPhyDeviceInfo; /* 04h */
+ U16 MaxTargetPortConnectTime; /* 08h */
+ U16 Reserved1; /* 0Ah */
} MPI_SAS_IO_UNIT1_PHY_DATA, MPI_POINTER PTR_MPI_SAS_IO_UNIT1_PHY_DATA,
SasIOUnit1PhyData, MPI_POINTER pSasIOUnit1PhyData;
@@ -2395,15 +2508,17 @@
CONFIG_EXTENDED_PAGE_HEADER Header; /* 00h */
U16 ControlFlags; /* 08h */
U16 MaxNumSATATargets; /* 0Ah */
- U32 Reserved1; /* 0Ch */
+ U16 AdditionalControlFlags; /* 0Ch */
+ U16 Reserved1; /* 0Eh */
U8 NumPhys; /* 10h */
U8 SATAMaxQDepth; /* 11h */
- U16 Reserved2; /* 12h */
+ U8 ReportDeviceMissingDelay; /* 12h */
+ U8 IODeviceMissingDelay; /* 13h */
MPI_SAS_IO_UNIT1_PHY_DATA PhyData[MPI_SAS_IOUNIT1_PHY_MAX]; /* 14h */
} CONFIG_PAGE_SAS_IO_UNIT_1, MPI_POINTER PTR_CONFIG_PAGE_SAS_IO_UNIT_1,
SasIOUnitPage1_t, MPI_POINTER pSasIOUnitPage1_t;
-#define MPI_SASIOUNITPAGE1_PAGEVERSION (0x05)
+#define MPI_SASIOUNITPAGE1_PAGEVERSION (0x06)
/* values for SAS IO Unit Page 1 ControlFlags */
#define MPI_SAS_IOUNIT1_CONTROL_DEVICE_SELF_TEST (0x8000)
@@ -2428,6 +2543,13 @@
#define MPI_SAS_IOUNIT1_CONTROL_FIRST_LVL_DISC_ONLY (0x0002)
#define MPI_SAS_IOUNIT1_CONTROL_CLEAR_AFFILIATION (0x0001)
+/* values for SAS IO Unit Page 1 AdditionalControlFlags */
+#define MPI_SAS_IOUNIT1_ACONTROL_ALLOW_TABLE_TO_TABLE (0x0001)
+
+/* defines for SAS IO Unit Page 1 ReportDeviceMissingDelay */
+#define MPI_SAS_IOUNIT1_REPORT_MISSING_TIMEOUT_MASK (0x7F)
+#define MPI_SAS_IOUNIT1_REPORT_MISSING_UNIT_16 (0x80)
+
/* values for SAS IO Unit Page 1 PortFlags */
#define MPI_SAS_IOUNIT1_PORT_FLAGS_0_TARGET_IOC_NUM (0x00)
#define MPI_SAS_IOUNIT1_PORT_FLAGS_1_TARGET_IOC_NUM (0x04)
diff --git a/drivers/message/fusion/lsi/mpi_history.txt b/drivers/message/fusion/lsi/mpi_history.txt
index 4a5f8dd..582cfe7 100644
--- a/drivers/message/fusion/lsi/mpi_history.txt
+++ b/drivers/message/fusion/lsi/mpi_history.txt
@@ -6,25 +6,25 @@
Copyright (c) 2000-2005 LSI Logic Corporation.
---------------------------------------
- Header Set Release Version: 01.05.12
- Header Set Release Date: 08-30-05
+ Header Set Release Version: 01.05.13
+ Header Set Release Date: 03-27-06
---------------------------------------
Filename Current version Prior version
---------- --------------- -------------
- mpi.h 01.05.10 01.05.09
- mpi_ioc.h 01.05.10 01.05.09
- mpi_cnfg.h 01.05.11 01.05.10
- mpi_init.h 01.05.06 01.05.06
- mpi_targ.h 01.05.05 01.05.05
+ mpi.h 01.05.11 01.05.10
+ mpi_ioc.h 01.05.11 01.05.10
+ mpi_cnfg.h 01.05.12 01.05.11
+ mpi_init.h 01.05.07 01.05.06
+ mpi_targ.h 01.05.06 01.05.05
mpi_fc.h 01.05.01 01.05.01
mpi_lan.h 01.05.01 01.05.01
mpi_raid.h 01.05.02 01.05.02
mpi_tool.h 01.05.03 01.05.03
mpi_inb.h 01.05.01 01.05.01
- mpi_sas.h 01.05.02 01.05.01
- mpi_type.h 01.05.02 01.05.01
- mpi_history.txt 01.05.12 01.05.11
+ mpi_sas.h 01.05.03 01.05.02
+ mpi_type.h 01.05.02 01.05.02
+ mpi_history.txt 01.05.13 01.05.12
* Date Version Description
@@ -93,6 +93,7 @@
* Added EEDP IOCStatus codes.
* 08-03-05 01.05.09 Bumped MPI_HEADER_VERSION_UNIT.
* 08-30-05 01.05.10 Added 2 new IOCStatus codes for Target.
+ * 03-27-06 01.05.11 Bumped MPI_HEADER_VERSION_UNIT.
* --------------------------------------------------------------------------
mpi_ioc.h
@@ -170,6 +171,17 @@
* Added new ReasonCode value for SAS Device Status Change
* event.
* Added new family code for FC949E.
+ * 03-27-06 01.05.11 Added MPI_IOCFACTS_CAPABILITY_TLR.
+ * Added additional Reason Codes and more event data fields
+ * to EVENT_DATA_SAS_DEVICE_STATUS_CHANGE.
+ * Added EVENT_DATA_SAS_BROADCAST_PRIMITIVE structure and
+ * new event.
+ * Added MPI_EVENT_SAS_SMP_ERROR and event data structure.
+ * Added MPI_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE and event
+ * data structure.
+ * Added MPI_EVENT_SAS_INIT_TABLE_OVERFLOW and event
+ * data structure.
+ * Added MPI_EXT_IMAGE_TYPE_INITIALIZATION.
* --------------------------------------------------------------------------
mpi_cnfg.h
@@ -425,6 +437,16 @@
* Added postpone SATA Init bit to SAS IO Unit Page 1
* ControlFlags.
* Changed LogEntry format for Log Page 0.
+ * 03-27-06 01.05.12 Added two new Flags defines for Manufacturing Page 4.
+ * Added Manufacturing Page 7.
+ * Added MPI_IOCPAGE2_CAP_FLAGS_RAID_64_BIT_ADDRESSING.
+ * Added IOC Page 6.
+ * Added PrevBootDeviceForm field to CONFIG_PAGE_BIOS_2.
+ * Added MaxLBAHigh field to RAID Volume Page 0.
+ * Added Nvdata version fields to SAS IO Unit Page 0.
+ * Added AdditionalControlFlags, MaxTargetPortConnectTime,
+ * ReportDeviceMissingDelay, and IODeviceMissingDelay
+ * fields to SAS IO Unit Page 1.
* --------------------------------------------------------------------------
mpi_init.h
@@ -467,6 +489,7 @@
* Added four new defines for SEP SlotStatus.
* 08-03-05 01.05.06 Fixed some MPI_SCSIIO32_MSGFLGS_ defines to make them
* unique in the first 32 characters.
+ * 03-27-06 01.05.07 Added Task Management type of Clear ACA.
* --------------------------------------------------------------------------
mpi_targ.h
@@ -511,6 +534,7 @@
* 02-22-05 01.05.03 Changed a comment.
* 03-11-05 01.05.04 Removed TargetAssistExtended Request.
* 06-24-05 01.05.05 Added TargetAssistExtended structures and defines.
+ * 03-27-06 01.05.06 Added a comment.
* --------------------------------------------------------------------------
mpi_fc.h
@@ -610,6 +634,10 @@
* 08-30-05 01.05.02 Added DeviceInfo bit for SEP.
* Added PrimFlags and Primitive field to SAS IO Unit
* Control request, and added a new operation code.
+ * 03-27-06 01.05.03 Added Force Full Discovery, Transmit Port Select Signal,
+ * and Remove Device operations to SAS IO Unit Control.
+ * Added DevHandle field to SAS IO Unit Control request and
+ * reply.
* --------------------------------------------------------------------------
mpi_type.h
@@ -625,20 +653,20 @@
mpi_history.txt Parts list history
-Filename 01.05.12 01.05.11 01.05.10 01.05.09
----------- -------- -------- -------- --------
-mpi.h 01.05.10 01.05.09 01.05.08 01.05.07
-mpi_ioc.h 01.05.10 01.05.09 01.05.09 01.05.08
-mpi_cnfg.h 01.05.11 01.05.10 01.05.09 01.05.08
-mpi_init.h 01.05.06 01.05.06 01.05.05 01.05.04
-mpi_targ.h 01.05.05 01.05.05 01.05.05 01.05.04
-mpi_fc.h 01.05.01 01.05.01 01.05.01 01.05.01
-mpi_lan.h 01.05.01 01.05.01 01.05.01 01.05.01
-mpi_raid.h 01.05.02 01.05.02 01.05.02 01.05.02
-mpi_tool.h 01.05.03 01.05.03 01.05.03 01.05.03
-mpi_inb.h 01.05.01 01.05.01 01.05.01 01.05.01
-mpi_sas.h 01.05.02 01.05.01 01.05.01 01.05.01
-mpi_type.h 01.05.02 01.05.01 01.05.01 01.05.01
+Filename 01.05.13 01.05.12 01.05.11 01.05.10 01.05.09
+---------- -------- -------- -------- -------- --------
+mpi.h 01.05.11 01.05.10 01.05.09 01.05.08 01.05.07
+mpi_ioc.h 01.05.11 01.05.10 01.05.09 01.05.09 01.05.08
+mpi_cnfg.h 01.05.12 01.05.11 01.05.10 01.05.09 01.05.08
+mpi_init.h 01.05.07 01.05.06 01.05.06 01.05.05 01.05.04
+mpi_targ.h 01.05.06 01.05.05 01.05.05 01.05.05 01.05.04
+mpi_fc.h 01.05.01 01.05.01 01.05.01 01.05.01 01.05.01
+mpi_lan.h 01.05.01 01.05.01 01.05.01 01.05.01 01.05.01
+mpi_raid.h 01.05.02 01.05.02 01.05.02 01.05.02 01.05.02
+mpi_tool.h 01.05.03 01.05.03 01.05.03 01.05.03 01.05.03
+mpi_inb.h 01.05.01 01.05.01 01.05.01 01.05.01 01.05.01
+mpi_sas.h 01.05.03 01.05.02 01.05.01 01.05.01 01.05.01
+mpi_type.h 01.05.02 01.05.02 01.05.01 01.05.01 01.05.01
Filename 01.05.08 01.05.07 01.05.06 01.05.05 01.05.04 01.05.03
---------- -------- -------- -------- -------- -------- --------
diff --git a/drivers/message/fusion/lsi/mpi_init.h b/drivers/message/fusion/lsi/mpi_init.h
index 68941f4..c1c6789 100644
--- a/drivers/message/fusion/lsi/mpi_init.h
+++ b/drivers/message/fusion/lsi/mpi_init.h
@@ -6,7 +6,7 @@
* Title: MPI initiator mode messages and structures
* Creation Date: June 8, 2000
*
- * mpi_init.h Version: 01.05.06
+ * mpi_init.h Version: 01.05.07
*
* Version History
* ---------------
@@ -52,6 +52,7 @@
* Added four new defines for SEP SlotStatus.
* 08-03-05 01.05.06 Fixed some MPI_SCSIIO32_MSGFLGS_ defines to make them
* unique in the first 32 characters.
+ * 03-27-06 01.05.07 Added Task Management type of Clear ACA.
* --------------------------------------------------------------------------
*/
@@ -427,6 +428,7 @@
#define MPI_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET (0x05)
#define MPI_SCSITASKMGMT_TASKTYPE_CLEAR_TASK_SET (0x06)
#define MPI_SCSITASKMGMT_TASKTYPE_QUERY_TASK (0x07)
+#define MPI_SCSITASKMGMT_TASKTYPE_CLEAR_ACA (0x08)
/* MsgFlags bits */
#define MPI_SCSITASKMGMT_MSGFLAGS_TARGET_RESET_OPTION (0x00)
diff --git a/drivers/message/fusion/lsi/mpi_ioc.h b/drivers/message/fusion/lsi/mpi_ioc.h
index 2c5f43f..18ba407 100644
--- a/drivers/message/fusion/lsi/mpi_ioc.h
+++ b/drivers/message/fusion/lsi/mpi_ioc.h
@@ -6,7 +6,7 @@
* Title: MPI IOC, Port, Event, FW Download, and FW Upload messages
* Creation Date: August 11, 2000
*
- * mpi_ioc.h Version: 01.05.10
+ * mpi_ioc.h Version: 01.05.11
*
* Version History
* ---------------
@@ -87,6 +87,17 @@
* Added new ReasonCode value for SAS Device Status Change
* event.
* Added new family code for FC949E.
+ * 03-27-06 01.05.11 Added MPI_IOCFACTS_CAPABILITY_TLR.
+ * Added additional Reason Codes and more event data fields
+ * to EVENT_DATA_SAS_DEVICE_STATUS_CHANGE.
+ * Added EVENT_DATA_SAS_BROADCAST_PRIMITIVE structure and
+ * new event.
+ * Added MPI_EVENT_SAS_SMP_ERROR and event data structure.
+ * Added MPI_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE and event
+ * data structure.
+ * Added MPI_EVENT_SAS_INIT_TABLE_OVERFLOW and event
+ * data structure.
+ * Added MPI_EXT_IMAGE_TYPE_INITIALIZATION.
* --------------------------------------------------------------------------
*/
@@ -272,6 +283,7 @@
#define MPI_IOCFACTS_CAPABILITY_MULTICAST (0x00000100)
#define MPI_IOCFACTS_CAPABILITY_SCSIIO32 (0x00000200)
#define MPI_IOCFACTS_CAPABILITY_NO_SCSIIO16 (0x00000400)
+#define MPI_IOCFACTS_CAPABILITY_TLR (0x00000800)
/*****************************************************************************
@@ -448,30 +460,34 @@
/* Event */
-#define MPI_EVENT_NONE (0x00000000)
-#define MPI_EVENT_LOG_DATA (0x00000001)
-#define MPI_EVENT_STATE_CHANGE (0x00000002)
-#define MPI_EVENT_UNIT_ATTENTION (0x00000003)
-#define MPI_EVENT_IOC_BUS_RESET (0x00000004)
-#define MPI_EVENT_EXT_BUS_RESET (0x00000005)
-#define MPI_EVENT_RESCAN (0x00000006)
-#define MPI_EVENT_LINK_STATUS_CHANGE (0x00000007)
-#define MPI_EVENT_LOOP_STATE_CHANGE (0x00000008)
-#define MPI_EVENT_LOGOUT (0x00000009)
-#define MPI_EVENT_EVENT_CHANGE (0x0000000A)
-#define MPI_EVENT_INTEGRATED_RAID (0x0000000B)
-#define MPI_EVENT_SCSI_DEVICE_STATUS_CHANGE (0x0000000C)
-#define MPI_EVENT_ON_BUS_TIMER_EXPIRED (0x0000000D)
-#define MPI_EVENT_QUEUE_FULL (0x0000000E)
-#define MPI_EVENT_SAS_DEVICE_STATUS_CHANGE (0x0000000F)
-#define MPI_EVENT_SAS_SES (0x00000010)
-#define MPI_EVENT_PERSISTENT_TABLE_FULL (0x00000011)
-#define MPI_EVENT_SAS_PHY_LINK_STATUS (0x00000012)
-#define MPI_EVENT_SAS_DISCOVERY_ERROR (0x00000013)
-#define MPI_EVENT_IR_RESYNC_UPDATE (0x00000014)
-#define MPI_EVENT_IR2 (0x00000015)
-#define MPI_EVENT_SAS_DISCOVERY (0x00000016)
-#define MPI_EVENT_LOG_ENTRY_ADDED (0x00000021)
+#define MPI_EVENT_NONE (0x00000000)
+#define MPI_EVENT_LOG_DATA (0x00000001)
+#define MPI_EVENT_STATE_CHANGE (0x00000002)
+#define MPI_EVENT_UNIT_ATTENTION (0x00000003)
+#define MPI_EVENT_IOC_BUS_RESET (0x00000004)
+#define MPI_EVENT_EXT_BUS_RESET (0x00000005)
+#define MPI_EVENT_RESCAN (0x00000006)
+#define MPI_EVENT_LINK_STATUS_CHANGE (0x00000007)
+#define MPI_EVENT_LOOP_STATE_CHANGE (0x00000008)
+#define MPI_EVENT_LOGOUT (0x00000009)
+#define MPI_EVENT_EVENT_CHANGE (0x0000000A)
+#define MPI_EVENT_INTEGRATED_RAID (0x0000000B)
+#define MPI_EVENT_SCSI_DEVICE_STATUS_CHANGE (0x0000000C)
+#define MPI_EVENT_ON_BUS_TIMER_EXPIRED (0x0000000D)
+#define MPI_EVENT_QUEUE_FULL (0x0000000E)
+#define MPI_EVENT_SAS_DEVICE_STATUS_CHANGE (0x0000000F)
+#define MPI_EVENT_SAS_SES (0x00000010)
+#define MPI_EVENT_PERSISTENT_TABLE_FULL (0x00000011)
+#define MPI_EVENT_SAS_PHY_LINK_STATUS (0x00000012)
+#define MPI_EVENT_SAS_DISCOVERY_ERROR (0x00000013)
+#define MPI_EVENT_IR_RESYNC_UPDATE (0x00000014)
+#define MPI_EVENT_IR2 (0x00000015)
+#define MPI_EVENT_SAS_DISCOVERY (0x00000016)
+#define MPI_EVENT_SAS_BROADCAST_PRIMITIVE (0x00000017)
+#define MPI_EVENT_SAS_INIT_DEVICE_STATUS_CHANGE (0x00000018)
+#define MPI_EVENT_SAS_INIT_TABLE_OVERFLOW (0x00000019)
+#define MPI_EVENT_SAS_SMP_ERROR (0x0000001A)
+#define MPI_EVENT_LOG_ENTRY_ADDED (0x00000021)
/* AckRequired field values */
@@ -558,18 +574,25 @@
U8 PhyNum; /* 0Eh */
U8 Reserved1; /* 0Fh */
U64 SASAddress; /* 10h */
+ U8 LUN[8]; /* 18h */
+ U16 TaskTag; /* 20h */
+ U16 Reserved2; /* 22h */
} EVENT_DATA_SAS_DEVICE_STATUS_CHANGE,
MPI_POINTER PTR_EVENT_DATA_SAS_DEVICE_STATUS_CHANGE,
MpiEventDataSasDeviceStatusChange_t,
MPI_POINTER pMpiEventDataSasDeviceStatusChange_t;
/* MPI SAS Device Status Change Event data ReasonCode values */
-#define MPI_EVENT_SAS_DEV_STAT_RC_ADDED (0x03)
-#define MPI_EVENT_SAS_DEV_STAT_RC_NOT_RESPONDING (0x04)
-#define MPI_EVENT_SAS_DEV_STAT_RC_SMART_DATA (0x05)
-#define MPI_EVENT_SAS_DEV_STAT_RC_NO_PERSIST_ADDED (0x06)
-#define MPI_EVENT_SAS_DEV_STAT_RC_UNSUPPORTED (0x07)
-#define MPI_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET (0x08)
+#define MPI_EVENT_SAS_DEV_STAT_RC_ADDED (0x03)
+#define MPI_EVENT_SAS_DEV_STAT_RC_NOT_RESPONDING (0x04)
+#define MPI_EVENT_SAS_DEV_STAT_RC_SMART_DATA (0x05)
+#define MPI_EVENT_SAS_DEV_STAT_RC_NO_PERSIST_ADDED (0x06)
+#define MPI_EVENT_SAS_DEV_STAT_RC_UNSUPPORTED (0x07)
+#define MPI_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET (0x08)
+#define MPI_EVENT_SAS_DEV_STAT_RC_TASK_ABORT_INTERNAL (0x09)
+#define MPI_EVENT_SAS_DEV_STAT_RC_ABORT_TASK_SET_INTERNAL (0x0A)
+#define MPI_EVENT_SAS_DEV_STAT_RC_CLEAR_TASK_SET_INTERNAL (0x0B)
+#define MPI_EVENT_SAS_DEV_STAT_RC_QUERY_TASK_INTERNAL (0x0C)
/* SCSI Event data for Queue Full event */
@@ -742,6 +765,27 @@
} EVENT_DATA_SAS_SES, MPI_POINTER PTR_EVENT_DATA_SAS_SES,
MpiEventDataSasSes_t, MPI_POINTER pMpiEventDataSasSes_t;
+/* SAS Broadcast Primitive Event data */
+
+typedef struct _EVENT_DATA_SAS_BROADCAST_PRIMITIVE
+{
+ U8 PhyNum; /* 00h */
+ U8 Port; /* 01h */
+ U8 PortWidth; /* 02h */
+ U8 Primitive; /* 04h */
+} EVENT_DATA_SAS_BROADCAST_PRIMITIVE,
+ MPI_POINTER PTR_EVENT_DATA_SAS_BROADCAST_PRIMITIVE,
+ MpiEventDataSasBroadcastPrimitive_t,
+ MPI_POINTER pMpiEventDataSasBroadcastPrimitive_t;
+
+#define MPI_EVENT_PRIMITIVE_CHANGE (0x01)
+#define MPI_EVENT_PRIMITIVE_EXPANDER (0x03)
+#define MPI_EVENT_PRIMITIVE_RESERVED2 (0x04)
+#define MPI_EVENT_PRIMITIVE_RESERVED3 (0x05)
+#define MPI_EVENT_PRIMITIVE_RESERVED4 (0x06)
+#define MPI_EVENT_PRIMITIVE_CHANGE0_RESERVED (0x07)
+#define MPI_EVENT_PRIMITIVE_CHANGE1_RESERVED (0x08)
+
/* SAS Phy Link Status Event data */
typedef struct _EVENT_DATA_SAS_PHY_LINK_STATUS
@@ -804,6 +848,53 @@
#define MPI_EVENT_DSCVRY_ERR_DS_MULTPL_PATHS (0x00000800)
#define MPI_EVENT_DSCVRY_ERR_DS_MAX_SATA_TARGETS (0x00001000)
+/* SAS SMP Error Event data */
+
+typedef struct _EVENT_DATA_SAS_SMP_ERROR
+{
+ U8 Status; /* 00h */
+ U8 Port; /* 01h */
+ U8 SMPFunctionResult; /* 02h */
+ U8 Reserved1; /* 03h */
+ U64 SASAddress; /* 04h */
+} EVENT_DATA_SAS_SMP_ERROR, MPI_POINTER PTR_EVENT_DATA_SAS_SMP_ERROR,
+ MpiEventDataSasSmpError_t, MPI_POINTER pMpiEventDataSasSmpError_t;
+
+/* defines for the Status field of the SAS SMP Error event */
+#define MPI_EVENT_SAS_SMP_FUNCTION_RESULT_VALID (0x00)
+#define MPI_EVENT_SAS_SMP_CRC_ERROR (0x01)
+#define MPI_EVENT_SAS_SMP_TIMEOUT (0x02)
+#define MPI_EVENT_SAS_SMP_NO_DESTINATION (0x03)
+#define MPI_EVENT_SAS_SMP_BAD_DESTINATION (0x04)
+
+/* SAS Initiator Device Status Change Event data */
+
+typedef struct _EVENT_DATA_SAS_INIT_DEV_STATUS_CHANGE
+{
+ U8 ReasonCode; /* 00h */
+ U8 Port; /* 01h */
+ U16 DevHandle; /* 02h */
+ U64 SASAddress; /* 04h */
+} EVENT_DATA_SAS_INIT_DEV_STATUS_CHANGE,
+ MPI_POINTER PTR_EVENT_DATA_SAS_INIT_DEV_STATUS_CHANGE,
+ MpiEventDataSasInitDevStatusChange_t,
+ MPI_POINTER pMpiEventDataSasInitDevStatusChange_t;
+
+/* defines for the ReasonCode field of the SAS Initiator Device Status Change event */
+#define MPI_EVENT_SAS_INIT_RC_ADDED (0x01)
+
+/* SAS Initiator Device Table Overflow Event data */
+
+typedef struct _EVENT_DATA_SAS_INIT_TABLE_OVERFLOW
+{
+ U8 MaxInit; /* 00h */
+ U8 CurrentInit; /* 01h */
+ U16 Reserved1; /* 02h */
+} EVENT_DATA_SAS_INIT_TABLE_OVERFLOW,
+ MPI_POINTER PTR_EVENT_DATA_SAS_INIT_TABLE_OVERFLOW,
+ MpiEventDataSasInitTableOverflow_t,
+ MPI_POINTER pMpiEventDataSasInitTableOverflow_t;
+
/*****************************************************************************
*
@@ -1013,5 +1104,6 @@
#define MPI_EXT_IMAGE_TYPE_FW (0x01)
#define MPI_EXT_IMAGE_TYPE_NVDATA (0x03)
#define MPI_EXT_IMAGE_TYPE_BOOTLOADER (0x04)
+#define MPI_EXT_IMAGE_TYPE_INITIALIZATION (0x05)
#endif
diff --git a/drivers/message/fusion/lsi/mpi_log_sas.h b/drivers/message/fusion/lsi/mpi_log_sas.h
index a9c14ad..871ebc0 100644
--- a/drivers/message/fusion/lsi/mpi_log_sas.h
+++ b/drivers/message/fusion/lsi/mpi_log_sas.h
@@ -13,6 +13,8 @@
#ifndef IOPI_IOCLOGINFO_H_INCLUDED
#define IOPI_IOCLOGINFO_H_INCLUDED
+#define SAS_LOGINFO_NEXUS_LOSS 0x31170000
+#define SAS_LOGINFO_MASK 0xFFFF0000
/****************************************************************************/
/* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */
@@ -51,6 +53,9 @@
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */
#define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */
+
+#define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */
+
#define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000)
#define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */
@@ -103,6 +108,7 @@
#define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000)
#define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000)
#define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000)
+#define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000)
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100)
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101)
#define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */
@@ -165,11 +171,81 @@
/****************************************************************************/
/* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */
/****************************************************************************/
-#define IR_LOGINFO_CODE_UNUSED1 (0x00010000)
-#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
+#define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000)
+#define IR_LOGINFO_CODE_UNUSED2 (0x00020000)
+
+/* Amount of information passed down for Create Volume is too large */
+#define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001)
+/* Creation of duplicate volume attempted (Bus/Target ID checked) */
+#define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002)
+/* Creation failed due to maximum number of supported volumes exceeded */
+#define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003)
+/* Creation failed due to DMA error in trying to read from host */
+#define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004)
+/* Creation failed due to invalid volume type passed down */
+#define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005)
+/* Creation failed due to error reading MFG Page 4 */
+#define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006)
+/* Creation failed when trying to create internal structures */
+#define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007)
+
+/* Activation failed due to trying to activate an already active volume */
+#define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010)
+/* Activation failed due to trying to active unsupported volume type */
+#define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011)
+/* Activation failed due to trying to active too many volumes */
+#define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012)
+/* Activation failed due to Volume ID in use already */
+#define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013)
+/* Activation failed call to activateVolume returned failure */
+#define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014)
+/* Activation failed trying to import the volume */
+#define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015)
+
+/* Phys Disk failed, too many phys disks */
+#define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020)
+/* Amount of information passed down for Create Pnysdisk is too large */
+#define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021)
+/* Creation failed due to DMA error in trying to read from host */
+#define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022)
+/* Creation failed due to invalid Bus TargetID passed down */
+#define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023)
+/* Creation failed due to error in creating RAID Phys Disk Config Page */
+#define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024)
+
+
+/* Compatibility Error : IR Disabled */
+#define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030)
+/* Compatibility Error : Inquiry Comand failed */
+#define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031)
+/* Compatibility Error : Device not direct access device */
+#define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032)
+/* Compatibility Error : Removable device found */
+#define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033)
+/* Compatibility Error : Device SCSI Version not 2 or higher */
+#define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034)
+/* Compatibility Error : SATA device, 48 BIT LBA not supported */
+#define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035)
+/* Compatibility Error : Device does not have 512 byte block sizes */
+#define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036)
+/* Compatibility Error : Volume Type check failed */
+#define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037)
+/* Compatibility Error : Volume Type is unsupported by FW */
+#define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038)
+/* Compatibility Error : Disk drive too small for use in volume */
+#define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039)
+/* Compatibility Error : Phys disk for Create Volume not found */
+#define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A)
+/* Compatibility Error : membership count error, too many or too few disks for volume type */
+#define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B)
+/* Compatibility Error : Disk stripe sizes must be 64KB */
+#define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C)
+/* Compatibility Error : IME size limited to < 2TB */
+#define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D)
+
/****************************************************************************/
-/* Defines for convienence */
+/* Defines for convenience */
/****************************************************************************/
#define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP)
#define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL)
diff --git a/drivers/message/fusion/lsi/mpi_sas.h b/drivers/message/fusion/lsi/mpi_sas.h
index 7051486..50b8f0a 100644
--- a/drivers/message/fusion/lsi/mpi_sas.h
+++ b/drivers/message/fusion/lsi/mpi_sas.h
@@ -6,7 +6,7 @@
* Title: MPI Serial Attached SCSI structures and definitions
* Creation Date: August 19, 2004
*
- * mpi_sas.h Version: 01.05.02
+ * mpi_sas.h Version: 01.05.03
*
* Version History
* ---------------
@@ -17,6 +17,10 @@
* 08-30-05 01.05.02 Added DeviceInfo bit for SEP.
* Added PrimFlags and Primitive field to SAS IO Unit
* Control request, and added a new operation code.
+ * 03-27-06 01.05.03 Added Force Full Discovery, Transmit Port Select Signal,
+ * and Remove Device operations to SAS IO Unit Control.
+ * Added DevHandle field to SAS IO Unit Control request and
+ * reply.
* --------------------------------------------------------------------------
*/
@@ -209,7 +213,7 @@
U8 Reserved1; /* 01h */
U8 ChainOffset; /* 02h */
U8 Function; /* 03h */
- U16 Reserved2; /* 04h */
+ U16 DevHandle; /* 04h */
U8 Reserved3; /* 06h */
U8 MsgFlags; /* 07h */
U32 MsgContext; /* 08h */
@@ -231,6 +235,9 @@
#define MPI_SAS_OP_PHY_CLEAR_ERROR_LOG (0x08)
#define MPI_SAS_OP_MAP_CURRENT (0x09)
#define MPI_SAS_OP_SEND_PRIMITIVE (0x0A)
+#define MPI_SAS_OP_FORCE_FULL_DISCOVERY (0x0B)
+#define MPI_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL (0x0C)
+#define MPI_SAS_OP_TRANSMIT_REMOVE_DEVICE (0x0D)
/* values for the PrimFlags field */
#define MPI_SAS_PRIMFLAGS_SINGLE (0x08)
@@ -245,7 +252,7 @@
U8 Reserved1; /* 01h */
U8 MsgLength; /* 02h */
U8 Function; /* 03h */
- U16 Reserved2; /* 04h */
+ U16 DevHandle; /* 04h */
U8 Reserved3; /* 06h */
U8 MsgFlags; /* 07h */
U32 MsgContext; /* 08h */
diff --git a/drivers/message/fusion/lsi/mpi_targ.h b/drivers/message/fusion/lsi/mpi_targ.h
index 3f46285..20b6673 100644
--- a/drivers/message/fusion/lsi/mpi_targ.h
+++ b/drivers/message/fusion/lsi/mpi_targ.h
@@ -6,7 +6,7 @@
* Title: MPI Target mode messages and structures
* Creation Date: June 22, 2000
*
- * mpi_targ.h Version: 01.05.05
+ * mpi_targ.h Version: 01.05.06
*
* Version History
* ---------------
@@ -54,6 +54,7 @@
* 02-22-05 01.05.03 Changed a comment.
* 03-11-05 01.05.04 Removed TargetAssistExtended Request.
* 06-24-05 01.05.05 Added TargetAssistExtended structures and defines.
+ * 03-27-06 01.05.06 Added a comment.
* --------------------------------------------------------------------------
*/
@@ -351,7 +352,7 @@
#define TARGET_ASSIST_FLAGS_CONFIRMED (0x08)
#define TARGET_ASSIST_FLAGS_REPOST_CMD_BUFFER (0x80)
-
+/* Standard Target Mode Reply message */
typedef struct _MSG_TARGET_ERROR_REPLY
{
U16 Reserved; /* 00h */