Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: make legacy IDE VLB modules check for the "probe" kernel params (v2)
ide: remove some obsoleted kernel params (v2)
ide/pci/delkin_cb.c: pci_module_init to pci_register_driver
scc_pata: bugfix for checking DMA IRQ status
ide: remove a ton of pointless #undef REALLY_SLOW_IO
siimage: DRAC4 note
adjust legacy IDE resource setting (v2)
ide: fix pmac breakage
ide-cs: Update device table
ide: ide_get_best_pio_mode() returns incorrect IORDY setting (take 2)
piix/slc90e66: more tuneproc() fixing (take 2)
ide: fix drive side 80c cable check, take 2
cmd64x: fix PIO mode setup (take 3)
alim15x3: fix PIO mode setup
diff --git a/Documentation/ide.txt b/Documentation/ide.txt
index 786c3a7..3bb9f9c 100644
--- a/Documentation/ide.txt
+++ b/Documentation/ide.txt
@@ -232,7 +232,9 @@
"hdx=remap63" : remap the drive: add 63 to all sector numbers
(for DM OnTrack)
-
+
+ "idex=noautotune" : driver will NOT attempt to tune interface speed
+
"hdx=autotune" : driver will attempt to tune interface speed
to the fastest PIO mode supported,
if possible for this drive only.
@@ -267,17 +269,6 @@
"idex=base,ctl" : specify both base and ctl
"idex=base,ctl,irq" : specify base, ctl, and irq number
-
- "idex=autotune" : driver will attempt to tune interface speed
- to the fastest PIO mode supported,
- for all drives on this interface.
- Not fully supported by all chipset types,
- and quite likely to cause trouble with
- older/odd IDE drives.
-
- "idex=noautotune" : driver will NOT attempt to tune interface speed
- This is the default for most chipsets,
- except the cmd640.
"idex=serialize" : do not overlap operations on idex. Please note
that you will have to specify this option for
@@ -303,13 +294,8 @@
to the first ATA interface found on the particular host, and the defaults for
the base,ctl ports must not be altered.
- "ide0=dtc2278" : probe/support DTC2278 interface
- "ide0=ht6560b" : probe/support HT6560B interface
"ide0=cmd640_vlb" : *REQUIRED* for VLB cards with the CMD640 chip
(not for PCI -- automatically detected)
- "ide0=qd65xx" : probe/support qd65xx interface
- "ide0=ali14xx" : probe/support ali14xx chipsets (ALI M1439/M1443/M1445)
- "ide0=umc8672" : probe/support umc8672 chipsets
"ide=doubler" : probe/support IDE doublers on Amiga
@@ -317,6 +303,15 @@
Everything else is rejected with a "BAD OPTION" message.
+For legacy IDE VLB host drivers (ali14xx/dtc2278/ht6560b/qd65xx/umc8672)
+you need to explicitly enable probing by using "probe" kernel parameter,
+i.e. to enable probing for ALI M14xx chipsets (ali14xx host driver) use:
+
+* "ali14xx.probe" boot option when ali14xx driver is built-in the kernel
+
+* "probe" module parameter when ali14xx driver is compiled as module
+ ("modprobe ali14xx probe")
+
================================================================================
IDE ATAPI streaming tape driver
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 49234e3..5d134bb 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1023,7 +1023,7 @@
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
help
- This driver is enabled at runtime using the "ide0=ali14xx" kernel
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
@@ -1033,7 +1033,7 @@
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
- This driver is enabled at runtime using the "ide0=dtc2278" kernel
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
well. See the <file:Documentation/ide.txt> and
@@ -1042,7 +1042,7 @@
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
help
- This driver is enabled at runtime using the "ide0=ht6560b" kernel
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
See the <file:Documentation/ide.txt> and
@@ -1051,7 +1051,7 @@
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
help
- This driver is enabled at runtime using the "ide0=qd65xx" kernel
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
<file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
more info.
@@ -1059,7 +1059,7 @@
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
help
- This driver is enabled at runtime using the "ide0=umc8672" kernel
+ This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
See the files <file:Documentation/ide.txt> and
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
index 6b2d152..556455f 100644
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -17,8 +17,6 @@
* device can't do DMA handshaking for some stupid reason. We don't need to do that.
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/timer.h>
diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c
index e2cea18..37aa6dd 100644
--- a/drivers/ide/ide-disk.c
+++ b/drivers/ide/ide-disk.c
@@ -43,8 +43,6 @@
#define IDEDISK_VERSION "1.18"
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
//#define DEBUG
#include <linux/module.h>
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index c67b3b1..bd513f5 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -583,6 +583,8 @@
if(!(drive->id->hw_config & 0x4000))
return 0;
#endif /* CONFIG_IDEDMA_IVB */
+ if (!(drive->id->hw_config & 0x2000))
+ return 0;
return 1;
}
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index 8afce4c..6871931 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -345,16 +345,16 @@
/**
* ide_get_best_pio_mode - get PIO mode from drive
- * @driver: drive to consider
+ * @drive: drive to consider
* @mode_wanted: preferred mode
- * @max_mode: highest allowed
- * @d: pio data
+ * @max_mode: highest allowed mode
+ * @d: PIO data
*
* This routine returns the recommended PIO settings for a given drive,
* based on the drive->id information and the ide_pio_blacklist[].
- * This is used by most chipset support modules when "auto-tuning".
*
- * Drive PIO mode auto selection
+ * Drive PIO mode is auto-selected if 255 is passed as mode_wanted.
+ * This is used by most chipset support modules when "auto-tuning".
*/
u8 ide_get_best_pio_mode (ide_drive_t *drive, u8 mode_wanted, u8 max_mode, ide_pio_data_t *d)
@@ -367,6 +367,7 @@
if (mode_wanted != 255) {
pio_mode = mode_wanted;
+ use_iordy = (pio_mode > 2);
} else if (!drive->id) {
pio_mode = 0;
} else if ((pio_mode = ide_scan_pio_blacklist(id->model)) != -1) {
@@ -396,19 +397,12 @@
}
}
-#if 0
- if (drive->id->major_rev_num & 0x0004) printk("ATA-2 ");
-#endif
-
/*
* Conservative "downgrade" for all pre-ATA2 drives
*/
if (pio_mode && pio_mode < 4) {
pio_mode--;
overridden = 1;
-#if 0
- use_iordy = (pio_mode > 2);
-#endif
if (cycle_time && cycle_time < ide_pio_timings[pio_mode].cycle_time)
cycle_time = 0; /* use standard timing */
}
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 8afbd6c..8f15c23 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -31,8 +31,6 @@
* valid after probe time even with noprobe
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/module.h>
#include <linux/types.h>
#include <linux/string.h>
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index b3c0818..dfbd744 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -126,8 +126,6 @@
#define REVISION "Revision: 7.00alpha2"
#define VERSION "Id: ide.c 7.00a2 20020906"
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#define _IDE_C /* Tell ide.h it's really us */
#include <linux/module.h>
@@ -1486,23 +1484,23 @@
}
#ifdef CONFIG_BLK_DEV_ALI14XX
-static int __initdata probe_ali14xx;
+extern int probe_ali14xx;
extern int ali14xx_init(void);
#endif
#ifdef CONFIG_BLK_DEV_UMC8672
-static int __initdata probe_umc8672;
+extern int probe_umc8672;
extern int umc8672_init(void);
#endif
#ifdef CONFIG_BLK_DEV_DTC2278
-static int __initdata probe_dtc2278;
+extern int probe_dtc2278;
extern int dtc2278_init(void);
#endif
#ifdef CONFIG_BLK_DEV_HT6560B
-static int __initdata probe_ht6560b;
+extern int probe_ht6560b;
extern int ht6560b_init(void);
#endif
#ifdef CONFIG_BLK_DEV_QD65XX
-static int __initdata probe_qd65xx;
+extern int probe_qd65xx;
extern int qd65xx_init(void);
#endif
@@ -1580,7 +1578,7 @@
*/
if (s[0] == 'h' && s[1] == 'd' && s[2] >= 'a' && s[2] <= max_drive) {
const char *hd_words[] = {
- "none", "noprobe", "nowerr", "cdrom", "serialize",
+ "none", "noprobe", "nowerr", "cdrom", "minus5",
"autotune", "noautotune", "minus8", "swapdata", "bswap",
"noflush", "remap", "remap63", "scsi", NULL };
unit = s[2] - 'a';
@@ -1608,9 +1606,6 @@
drive->ready_stat = 0;
hwif->noprobe = 0;
goto done;
- case -5: /* "serialize" */
- printk(" -- USE \"ide%d=serialize\" INSTEAD", hw);
- goto do_serialize;
case -6: /* "autotune" */
drive->autotune = IDE_TUNE_AUTO;
goto obsolete_option;
@@ -1671,7 +1666,7 @@
* (-8, -9, -10) are reserved to ease the hardcoding.
*/
static const char *ide_words[] = {
- "noprobe", "serialize", "autotune", "noautotune",
+ "noprobe", "serialize", "minus3", "minus4",
"reset", "dma", "ata66", "minus8", "minus9",
"minus10", "four", "qd65xx", "ht6560b", "cmd640_vlb",
"dtc2278", "umc8672", "ali14xx", NULL };
@@ -1742,12 +1737,17 @@
hwif->chipset = mate->chipset = ide_4drives;
mate->irq = hwif->irq;
memcpy(mate->io_ports, hwif->io_ports, sizeof(hwif->io_ports));
- goto do_serialize;
+ hwif->mate = mate;
+ mate->mate = hwif;
+ hwif->serialized = mate->serialized = 1;
+ goto obsolete_option;
}
#endif /* CONFIG_BLK_DEV_4DRIVES */
case -10: /* minus10 */
case -9: /* minus9 */
case -8: /* minus8 */
+ case -4:
+ case -3:
goto bad_option;
case -7: /* ata66 */
#ifdef CONFIG_BLK_DEV_IDEPCI
@@ -1762,16 +1762,7 @@
case -5: /* "reset" */
hwif->reset = 1;
goto obsolete_option;
- case -4: /* "noautotune" */
- hwif->drives[0].autotune = IDE_TUNE_NOAUTO;
- hwif->drives[1].autotune = IDE_TUNE_NOAUTO;
- goto obsolete_option;
- case -3: /* "autotune" */
- hwif->drives[0].autotune = IDE_TUNE_AUTO;
- hwif->drives[1].autotune = IDE_TUNE_AUTO;
- goto obsolete_option;
case -2: /* "serialize" */
- do_serialize:
hwif->mate = &ide_hwifs[hw^1];
hwif->mate->mate = hwif;
hwif->serialized = hwif->mate->serialized = 1;
@@ -1840,8 +1831,8 @@
#endif /* CONFIG_BLK_DEV_CMD640 */
#ifdef CONFIG_BLK_DEV_IDE_PMAC
{
- extern void pmac_ide_probe(void);
- pmac_ide_probe();
+ extern int pmac_ide_probe(void);
+ (void)pmac_ide_probe();
}
#endif /* CONFIG_BLK_DEV_IDE_PMAC */
#ifdef CONFIG_BLK_DEV_GAYLE
diff --git a/drivers/ide/legacy/ali14xx.c b/drivers/ide/legacy/ali14xx.c
index 9c54446..91961aa 100644
--- a/drivers/ide/legacy/ali14xx.c
+++ b/drivers/ide/legacy/ali14xx.c
@@ -37,8 +37,6 @@
* mode 4 for a while now with no trouble.) -Derek
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
@@ -230,9 +228,17 @@
return 0;
}
+int probe_ali14xx = 0;
+
+module_param_named(probe, probe_ali14xx, bool, 0);
+MODULE_PARM_DESC(probe, "probe for ALI M14xx chipsets");
+
/* Can be called directly from ide.c. */
int __init ali14xx_init(void)
{
+ if (probe_ali14xx == 0)
+ goto out;
+
/* auto-detect IDE controller port */
if (findPort()) {
if (ali14xx_probe())
@@ -240,6 +246,7 @@
return 0;
}
printk(KERN_ERR "ali14xx: not found.\n");
+out:
return -ENODEV;
}
diff --git a/drivers/ide/legacy/dtc2278.c b/drivers/ide/legacy/dtc2278.c
index 3b1d33b..0219ffa 100644
--- a/drivers/ide/legacy/dtc2278.c
+++ b/drivers/ide/legacy/dtc2278.c
@@ -4,8 +4,6 @@
* Copyright (C) 1996 Linus Torvalds & author (see below)
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
@@ -94,7 +92,7 @@
HWIF(drive)->drives[!drive->select.b.unit].io_32bit = 1;
}
-static int __init probe_dtc2278(void)
+static int __init dtc2278_probe(void)
{
unsigned long flags;
ide_hwif_t *hwif, *mate;
@@ -145,10 +143,18 @@
return 0;
}
+int probe_dtc2278 = 0;
+
+module_param_named(probe, probe_dtc2278, bool, 0);
+MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
+
/* Can be called directly from ide.c. */
int __init dtc2278_init(void)
{
- if (probe_dtc2278()) {
+ if (probe_dtc2278 == 0)
+ return -ENODEV;
+
+ if (dtc2278_probe()) {
printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
return -EBUSY;
}
diff --git a/drivers/ide/legacy/ht6560b.c b/drivers/ide/legacy/ht6560b.c
index 19ccd00..a283264 100644
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -36,8 +36,6 @@
#define HT6560B_VERSION "v0.07"
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
@@ -303,12 +301,20 @@
#endif
}
+int probe_ht6560b = 0;
+
+module_param_named(probe, probe_ht6560b, bool, 0);
+MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
+
/* Can be called directly from ide.c. */
int __init ht6560b_init(void)
{
ide_hwif_t *hwif, *mate;
int t;
+ if (probe_ht6560b == 0)
+ return -ENODEV;
+
hwif = &ide_hwifs[0];
mate = &ide_hwifs[1];
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index a5023cd..b08c37c 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -359,14 +359,17 @@
static struct pcmcia_device_id ide_ids[] = {
PCMCIA_DEVICE_FUNC_ID(4),
PCMCIA_DEVICE_MANF_CARD(0x0007, 0x0000), /* Hitachi */
+ PCMCIA_DEVICE_MANF_CARD(0x000a, 0x0000), /* I-O Data CFA */
+ PCMCIA_DEVICE_MANF_CARD(0x001c, 0x0001), /* Mitsubishi CFA */
PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704),
- PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401),
+ PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401), /* SanDisk CFA */
PCMCIA_DEVICE_MANF_CARD(0x0098, 0x0000), /* Toshiba */
PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
PCMCIA_DEVICE_MANF_CARD(0x00ce, 0x0000), /* Samsung */
PCMCIA_DEVICE_MANF_CARD(0x0319, 0x0000), /* Hitachi */
PCMCIA_DEVICE_MANF_CARD(0x2080, 0x0001),
- PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0200), /* Lexar */
+ PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0100), /* Viking CFA */
+ PCMCIA_DEVICE_MANF_CARD(0x4e01, 0x0200), /* Lexar, Viking CFA */
PCMCIA_DEVICE_PROD_ID123("Caravelle", "PSC-IDE ", "PSC000", 0x8c36137c, 0xd0693ab8, 0x2768a9f0),
PCMCIA_DEVICE_PROD_ID123("CDROM", "IDE", "MCD-601p", 0x1b9179ca, 0xede88951, 0x0d902f74),
PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9),
diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c
index d3c3bc2..2fb8f50 100644
--- a/drivers/ide/legacy/qd65xx.c
+++ b/drivers/ide/legacy/qd65xx.c
@@ -16,8 +16,8 @@
* Please set local bus speed using kernel parameter idebus
* for example, "idebus=33" stands for 33Mhz VLbus
* To activate controller support, use "ide0=qd65xx"
- * To enable tuning, use "ide0=autotune"
- * To enable second channel tuning (qd6580 only), use "ide1=autotune"
+ * To enable tuning, use "hda=autotune hdb=autotune"
+ * To enable 2nd channel tuning (qd6580 only), use "hdc=autotune hdd=autotune"
*/
/*
@@ -25,8 +25,6 @@
* Samuel Thibault <samuel.thibault@fnac.net>
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
@@ -490,9 +488,17 @@
return 1;
}
+int probe_qd65xx = 0;
+
+module_param_named(probe, probe_qd65xx, bool, 0);
+MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
+
/* Can be called directly from ide.c. */
int __init qd65xx_init(void)
{
+ if (probe_qd65xx == 0)
+ return -ENODEV;
+
if (qd_probe(0x30))
qd_probe(0xb0);
if (ide_hwifs[0].chipset != ide_qd65xx &&
diff --git a/drivers/ide/legacy/umc8672.c b/drivers/ide/legacy/umc8672.c
index 6e2c58c..ca79744 100644
--- a/drivers/ide/legacy/umc8672.c
+++ b/drivers/ide/legacy/umc8672.c
@@ -165,12 +165,21 @@
return 0;
}
+int probe_umc8672 = 0;
+
+module_param_named(probe, probe_umc8672, bool, 0);
+MODULE_PARM_DESC(probe, "probe for UMC8672 chipset");
+
/* Can be called directly from ide.c. */
int __init umc8672_init(void)
{
- if (umc8672_probe())
- return -ENODEV;
- return 0;
+ if (probe_umc8672 == 0)
+ goto out;
+
+ if (umc8672_probe() == 0)
+ return 0;;
+out:
+ return -ENODEV;;
}
#ifdef MODULE
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index 0a59d5e..b2dc028 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -29,8 +29,6 @@
* Note: for more information, please refer "AMD Alchemy Au1200/Au1550 IDE
* Interface and Linux Device Driver" Application Note.
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index 4debd18..83e0aa6 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/alim15x3.c Version 0.17 2003/01/02
+ * linux/drivers/ide/pci/alim15x3.c Version 0.21 2007/02/03
*
* Copyright (C) 1998-2000 Michel Aubry, Maintainer
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
@@ -9,6 +9,7 @@
* May be copied or modified under the terms of the GNU General Public License
* Copyright (C) 2002 Alan Cox <alan@redhat.com>
* ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
+ * Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
*
* (U)DMA capable version of ali 1533/1543(C), 1535(D)
*
@@ -280,15 +281,17 @@
#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_PROC_FS) */
/**
- * ali15x3_tune_drive - set up a drive
+ * ali15x3_tune_pio - set up chipset for PIO mode
* @drive: drive to tune
- * @pio: unused
+ * @pio: desired mode
*
- * Select the best PIO timing for the drive in question. Then
- * program the controller for this drive set up
+ * Select the best PIO mode for the drive in question.
+ * Then program the controller for this mode.
+ *
+ * Returns the PIO mode programmed.
*/
-static void ali15x3_tune_drive (ide_drive_t *drive, u8 pio)
+static u8 ali15x3_tune_pio (ide_drive_t *drive, u8 pio)
{
ide_pio_data_t d;
ide_hwif_t *hwif = HWIF(drive);
@@ -356,6 +359,22 @@
* { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
*/
+ return pio;
+}
+
+/**
+ * ali15x3_tune_drive - set up drive for PIO mode
+ * @drive: drive to tune
+ * @pio: desired mode
+ *
+ * Program the controller with the best PIO timing for the given drive.
+ * Then set up the drive itself.
+ */
+
+static void ali15x3_tune_drive (ide_drive_t *drive, u8 pio)
+{
+ pio = ali15x3_tune_pio(drive, pio);
+ (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
/**
@@ -430,7 +449,7 @@
}
/**
- * ali15x3_tune_chipset - set up chiset for new speed
+ * ali15x3_tune_chipset - set up chipset/drive for new speed
* @drive: drive to configure for
* @xferspeed: desired speed
*
@@ -461,7 +480,7 @@
pci_write_config_byte(dev, m5229_udma, tmpbyte);
if (speed < XFER_SW_DMA_0)
- ali15x3_tune_drive(drive, speed);
+ (void) ali15x3_tune_pio(drive, speed - XFER_PIO_0);
} else {
pci_read_config_byte(dev, m5229_udma, &tmpbyte);
tmpbyte &= (0x0f << ((1-unit) << 2));
diff --git a/drivers/ide/pci/cmd640.c b/drivers/ide/pci/cmd640.c
index 61b5f9c..dc43f00 100644
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -98,7 +98,6 @@
* (patch courtesy of Zoltan Hidvegi)
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
#define CMD640_PREFETCH_MASKS 1
//#define CMD640_DUMP_REGS
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 49df275..b0d4825 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -1,6 +1,6 @@
/* $Id: cmd64x.c,v 1.21 2000/01/30 23:23:16
*
- * linux/drivers/ide/pci/cmd64x.c Version 1.30 Sept 10, 2002
+ * linux/drivers/ide/pci/cmd64x.c Version 1.41 Feb 3, 2007
*
* cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
* Note, this driver is not used at all on other systems because
@@ -12,6 +12,7 @@
* Copyright (C) 1998 David S. Miller (davem@redhat.com)
*
* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
*/
#include <linux/module.h>
@@ -262,43 +263,25 @@
}
/*
- * Attempts to set the interface PIO mode.
- * The preferred method of selecting PIO modes (e.g. mode 4) is
- * "echo 'piomode:4' > /proc/ide/hdx/settings". Special cases are
- * 8: prefetch off, 9: prefetch on, 255: auto-select best mode.
- * Called with 255 at boot time.
+ * This routine selects drive's best PIO mode, calculates setup/active/recovery
+ * counts, and then writes them into the chipset registers.
*/
-
-static void cmd64x_tuneproc (ide_drive_t *drive, u8 mode_wanted)
+static u8 cmd64x_tune_pio (ide_drive_t *drive, u8 mode_wanted)
{
int setup_time, active_time, recovery_time;
int clock_time, pio_mode, cycle_time;
u8 recovery_count2, cycle_count;
int setup_count, active_count, recovery_count;
int bus_speed = system_bus_clock();
- /*byte b;*/
ide_pio_data_t d;
- switch (mode_wanted) {
- case 8: /* set prefetch off */
- case 9: /* set prefetch on */
- mode_wanted &= 1;
- /*set_prefetch_mode(index, mode_wanted);*/
- cmdprintk("%s: %sabled cmd640 prefetch\n",
- drive->name, mode_wanted ? "en" : "dis");
- return;
- }
-
- mode_wanted = ide_get_best_pio_mode (drive, mode_wanted, 5, &d);
- pio_mode = d.pio_mode;
+ pio_mode = ide_get_best_pio_mode(drive, mode_wanted, 5, &d);
cycle_time = d.cycle_time;
/*
* I copied all this complicated stuff from cmd640.c and made a few
* minor changes. For now I am just going to pray that it is correct.
*/
- if (pio_mode > 5)
- pio_mode = 5;
setup_time = ide_pio_timings[pio_mode].setup_time;
active_time = ide_pio_timings[pio_mode].active_time;
recovery_time = cycle_time - (setup_time + active_time);
@@ -320,22 +303,33 @@
if (active_count > 16)
active_count = 16; /* maximum allowed by cmd646 */
- /*
- * In a perfect world, we might set the drive pio mode here
- * (using WIN_SETFEATURE) before continuing.
- *
- * But we do not, because:
- * 1) this is the wrong place to do it
- * (proper is do_special() in ide.c)
- * 2) in practice this is rarely, if ever, necessary
- */
program_drive_counts (drive, setup_count, active_count, recovery_count);
- cmdprintk("%s: selected cmd646 PIO mode%d : %d (%dns)%s, "
+ cmdprintk("%s: PIO mode wanted %d, selected %d (%dns)%s, "
"clocks=%d/%d/%d\n",
- drive->name, pio_mode, mode_wanted, cycle_time,
+ drive->name, mode_wanted, pio_mode, cycle_time,
d.overridden ? " (overriding vendor mode)" : "",
setup_count, active_count, recovery_count);
+
+ return pio_mode;
+}
+
+/*
+ * Attempts to set drive's PIO mode.
+ * Special cases are 8: prefetch off, 9: prefetch on (both never worked),
+ * and 255: auto-select best mode (used at boot time).
+ */
+static void cmd64x_tune_drive (ide_drive_t *drive, u8 pio)
+{
+ /*
+ * Filter out the prefetch control values
+ * to prevent PIO5 from being programmed
+ */
+ if (pio == 8 || pio == 9)
+ return;
+
+ pio = cmd64x_tune_pio(drive, pio);
+ (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
static u8 cmd64x_ratemask (ide_drive_t *drive)
@@ -387,22 +381,6 @@
return mode;
}
-static void config_cmd64x_chipset_for_pio (ide_drive_t *drive, u8 set_speed)
-{
- u8 speed = 0x00;
- u8 set_pio = ide_get_best_pio_mode(drive, 4, 5, NULL);
-
- cmd64x_tuneproc(drive, set_pio);
- speed = XFER_PIO_0 + set_pio;
- if (set_speed)
- (void) ide_config_drive_speed(drive, speed);
-}
-
-static void config_chipset_for_pio (ide_drive_t *drive, u8 set_speed)
-{
- config_cmd64x_chipset_for_pio(drive, set_speed);
-}
-
static int cmd64x_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
ide_hwif_t *hwif = HWIF(drive);
@@ -414,7 +392,7 @@
u8 speed = ide_rate_filter(cmd64x_ratemask(drive), xferspeed);
- if (speed > XFER_PIO_4) {
+ if (speed >= XFER_SW_DMA_0) {
(void) pci_read_config_byte(dev, pciD, ®D);
(void) pci_read_config_byte(dev, pciU, ®U);
regD &= ~(unit ? 0x40 : 0x20);
@@ -438,17 +416,20 @@
case XFER_SW_DMA_2: regD |= (unit ? 0x40 : 0x10); break;
case XFER_SW_DMA_1: regD |= (unit ? 0x80 : 0x20); break;
case XFER_SW_DMA_0: regD |= (unit ? 0xC0 : 0x30); break;
- case XFER_PIO_4: cmd64x_tuneproc(drive, 4); break;
- case XFER_PIO_3: cmd64x_tuneproc(drive, 3); break;
- case XFER_PIO_2: cmd64x_tuneproc(drive, 2); break;
- case XFER_PIO_1: cmd64x_tuneproc(drive, 1); break;
- case XFER_PIO_0: cmd64x_tuneproc(drive, 0); break;
+ case XFER_PIO_5:
+ case XFER_PIO_4:
+ case XFER_PIO_3:
+ case XFER_PIO_2:
+ case XFER_PIO_1:
+ case XFER_PIO_0:
+ (void) cmd64x_tune_pio(drive, speed - XFER_PIO_0);
+ break;
default:
return 1;
}
- if (speed > XFER_PIO_4) {
+ if (speed >= XFER_SW_DMA_0) {
(void) pci_write_config_byte(dev, pciU, regU);
regD |= (unit ? 0x40 : 0x20);
(void) pci_write_config_byte(dev, pciD, regD);
@@ -461,8 +442,6 @@
{
u8 speed = ide_dma_speed(drive, cmd64x_ratemask(drive));
- config_chipset_for_pio(drive, !speed);
-
if (!speed)
return 0;
@@ -478,7 +457,7 @@
return 0;
if (ide_use_fast_pio(drive))
- config_chipset_for_pio(drive, 1);
+ cmd64x_tune_drive(drive, 255);
return -1;
}
@@ -679,14 +658,13 @@
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xff;
- hwif->tuneproc = &cmd64x_tuneproc;
+ hwif->tuneproc = &cmd64x_tune_drive;
hwif->speedproc = &cmd64x_tune_chipset;
- if (!hwif->dma_base) {
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
+ hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
+
+ if (!hwif->dma_base)
return;
- }
hwif->atapi_dma = 1;
diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
index e2672fc..d4b753e 100644
--- a/drivers/ide/pci/delkin_cb.c
+++ b/drivers/ide/pci/delkin_cb.c
@@ -122,7 +122,7 @@
static int
delkin_cb_init (void)
{
- return pci_module_init(&driver);
+ return pci_register_driver(&driver);
}
static void
diff --git a/drivers/ide/pci/generic.c b/drivers/ide/pci/generic.c
index b408c6c..f2c5a14 100644
--- a/drivers/ide/pci/generic.c
+++ b/drivers/ide/pci/generic.c
@@ -21,8 +21,6 @@
* are deemed to be part of the source code.
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 9ca60dd..aede7ee 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -57,7 +57,7 @@
* There is a 25/33MHz switch in configuration
* register, but driver is written for use at any frequency which get
* (use idebus=xx to select PCI bus speed).
- * Use ide0=autotune for automatical tune of the PIO modes.
+ * Use hda=autotune and hdb=autotune for automatical tune of the PIO modes.
* If you get strange results, do not use this and set PIO manually
* by hdparm.
*
@@ -87,7 +87,6 @@
* 0.5 doesn't work.
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
#define OPTI621_DEBUG /* define for debug messages */
#include <linux/types.h>
diff --git a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c
index 569822f..061d300 100644
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -1,10 +1,10 @@
/*
- * linux/drivers/ide/pci/piix.c Version 0.46 December 3, 2006
+ * linux/drivers/ide/pci/piix.c Version 0.47 February 8, 2007
*
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
- * Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
@@ -205,14 +205,13 @@
}
/**
- * piix_tune_drive - tune a drive attached to a PIIX
+ * piix_tune_pio - tune PIIX for PIO mode
* @drive: drive to tune
* @pio: desired PIO mode
*
- * Set the interface PIO mode based upon the settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
+ * Set the interface PIO mode based upon the settings done by AMI BIOS.
*/
-static void piix_tune_drive (ide_drive_t *drive, u8 pio)
+static void piix_tune_pio (ide_drive_t *drive, u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -233,8 +232,6 @@
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
-
/*
* Master vs slave is synchronized above us but the slave register is
* shared by the two hwifs so the corner case of two slave timeouts in
@@ -253,19 +250,20 @@
master_data |= 0x4000;
master_data &= ~0x0070;
if (pio > 1) {
- /* enable PPE, IE and TIME */
- master_data = master_data | (control << 4);
+ /* Set PPE, IE and TIME */
+ master_data |= control << 4;
}
pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
- slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
+ slave_data &= hwif->channel ? 0x0f : 0xf0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) <<
+ (hwif->channel ? 4 : 0);
} else {
master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
- master_data = master_data | control;
+ master_data |= control;
}
- master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
+ master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
if (is_slave)
@@ -274,6 +272,21 @@
}
/**
+ * piix_tune_drive - tune a drive attached to PIIX
+ * @drive: drive to tune
+ * @pio: desired PIO mode
+ *
+ * Set the drive's PIO mode (might be useful if drive is not registered
+ * in CMOS for any reason).
+ */
+static void piix_tune_drive (ide_drive_t *drive, u8 pio)
+{
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+ piix_tune_pio(drive, pio);
+ (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
+}
+
+/**
* piix_tune_chipset - tune a PIIX interface
* @drive: IDE drive to tune
* @xferspeed: speed to configure
@@ -348,8 +361,8 @@
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
- piix_tune_drive(drive, piix_dma_2_pio(speed));
- return (ide_config_drive_speed(drive, speed));
+ piix_tune_pio(drive, piix_dma_2_pio(speed));
+ return ide_config_drive_speed(drive, speed);
}
/**
@@ -392,9 +405,7 @@
return 0;
if (ide_use_fast_pio(drive))
- /* Find best PIO mode. */
- piix_tune_chipset(drive, XFER_PIO_0 +
- ide_get_best_pio_mode(drive, 255, 4, NULL));
+ piix_tune_drive(drive, 255);
return -1;
}
diff --git a/drivers/ide/pci/rz1000.c b/drivers/ide/pci/rz1000.c
index c185531..f8c95469 100644
--- a/drivers/ide/pci/rz1000.c
+++ b/drivers/ide/pci/rz1000.c
@@ -15,8 +15,6 @@
* Dunno if this fixes both ports, or only the primary port (?).
*/
-#undef REALLY_SLOW_IO /* most systems can safely undef this */
-
#include <linux/types.h>
#include <linux/module.h>
#include <linux/kernel.h>
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index 7b4c189..71eccdf 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -26,6 +26,11 @@
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
* if neccessary
+ *
+ * The Dell DRAC4 has some interesting features including effectively hot
+ * unplugging/replugging the virtual CD interface when the DRAC is reset.
+ * This often causes drivers/ide/siimage to panic but is ok with the rather
+ * smarter code in libata.
*/
#include <linux/types.h>
diff --git a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c
index ae7eb58..852ccb3 100644
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -1,8 +1,8 @@
/*
- * linux/drivers/ide/pci/slc90e66.c Version 0.13 December 30, 2006
+ * linux/drivers/ide/pci/slc90e66.c Version 0.14 February 8, 2007
*
* Copyright (C) 2000-2002 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
*
* This is a look-alike variation of the ICH0 PIIX4 Ultra-66,
* but this keeps the ISA-Bridge and slots alive.
@@ -57,11 +57,7 @@
}
}
-/*
- * Based on settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
- */
-static void slc90e66_tune_drive (ide_drive_t *drive, u8 pio)
+static void slc90e66_tune_pio (ide_drive_t *drive, u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -80,7 +76,6 @@
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
spin_lock_irqsave(&ide_lock, flags);
pci_read_config_word(dev, master_port, &master_data);
@@ -94,19 +89,20 @@
master_data |= 0x4000;
master_data &= ~0x0070;
if (pio > 1) {
- /* enable PPE, IE and TIME */
- master_data = master_data | (control << 4);
+ /* Set PPE, IE and TIME */
+ master_data |= control << 4;
}
pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
- slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
+ slave_data &= hwif->channel ? 0x0f : 0xf0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) <<
+ (hwif->channel ? 4 : 0);
} else {
master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
- master_data = master_data | control;
+ master_data |= control;
}
- master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
+ master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
if (is_slave)
@@ -114,6 +110,13 @@
spin_unlock_irqrestore(&ide_lock, flags);
}
+static void slc90e66_tune_drive (ide_drive_t *drive, u8 pio)
+{
+ pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+ slc90e66_tune_pio(drive, pio);
+ (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
+}
+
static int slc90e66_tune_chipset (ide_drive_t *drive, u8 xferspeed)
{
ide_hwif_t *hwif = HWIF(drive);
@@ -162,8 +165,8 @@
pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
}
- slc90e66_tune_drive(drive, slc90e66_dma_2_pio(speed));
- return (ide_config_drive_speed(drive, speed));
+ slc90e66_tune_pio(drive, slc90e66_dma_2_pio(speed));
+ return ide_config_drive_speed(drive, speed);
}
static int slc90e66_config_drive_for_dma (ide_drive_t *drive)
@@ -185,8 +188,7 @@
return 0;
if (ide_use_fast_pio(drive))
- (void)slc90e66_tune_chipset(drive, XFER_PIO_0 +
- ide_get_best_pio_mode(drive, 255, 4, NULL));
+ slc90e66_tune_drive(drive, 255);
return -1;
}
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index 395d352..071a030 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -48,7 +48,7 @@
#include <asm/mediabay.h>
#endif
-#include "ide-timing.h"
+#include "../ide-timing.h"
#undef IDE_PMAC_DEBUG
@@ -1551,19 +1551,34 @@
};
MODULE_DEVICE_TABLE(pci, pmac_ide_pci_match);
-void __init
-pmac_ide_probe(void)
+int __init pmac_ide_probe(void)
{
+ int error;
+
if (!machine_is(powermac))
- return;
+ return -ENODEV;
#ifdef CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST
- pci_register_driver(&pmac_ide_pci_driver);
- macio_register_driver(&pmac_ide_macio_driver);
+ error = pci_register_driver(&pmac_ide_pci_driver);
+ if (error)
+ goto out;
+ error = macio_register_driver(&pmac_ide_macio_driver);
+ if (error) {
+ pci_unregister_driver(&pmac_ide_pci_driver);
+ goto out;
+ }
#else
- macio_register_driver(&pmac_ide_macio_driver);
- pci_register_driver(&pmac_ide_pci_driver);
+ error = macio_register_driver(&pmac_ide_macio_driver);
+ if (error)
+ goto out;
+ error = pci_register_driver(&pmac_ide_pci_driver);
+ if (error) {
+ macio_unregister_driver(&pmac_ide_macio_driver);
+ goto out;
+ }
#endif
+out:
+ return error;
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
@@ -1983,7 +1998,7 @@
{
}
-static int pmac_ide_dma_host_on(ide_drive_t *drive)
+static void pmac_ide_dma_host_on(ide_drive_t *drive)
{
}
diff --git a/drivers/ide/ppc/scc_pata.c b/drivers/ide/ppc/scc_pata.c
index de64b02..f84bf79 100644
--- a/drivers/ide/ppc/scc_pata.c
+++ b/drivers/ide/ppc/scc_pata.c
@@ -509,6 +509,32 @@
return __ide_dma_end(drive);
}
+/* returns 1 if dma irq issued, 0 otherwise */
+static int scc_dma_test_irq(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = HWIF(drive);
+ u8 dma_stat = hwif->INB(hwif->dma_status);
+
+ /* return 1 if INTR asserted */
+ if ((dma_stat & 4) == 4)
+ return 1;
+
+ /* Workaround for PTERADD: emulate DMA_INTR when
+ * - IDE_STATUS[ERR] = 1
+ * - INT_STATUS[INTRQ] = 1
+ * - DMA_STATUS[IORACTA] = 1
+ */
+ if (in_be32((void __iomem *)IDE_ALTSTATUS_REG) & ERR_STAT &&
+ in_be32((void __iomem *)(hwif->dma_base + 0x014)) & INTSTS_INTRQ &&
+ dma_stat & 1)
+ return 1;
+
+ if (!drive->waiting_for_dma)
+ printk(KERN_WARNING "%s: (%s) called while not waiting\n",
+ drive->name, __FUNCTION__);
+ return 0;
+}
+
/**
* setup_mmio_scc - map CTRL/BMID region
* @dev: PCI device we are configuring
@@ -712,6 +738,7 @@
hwif->speedproc = scc_tune_chipset;
hwif->tuneproc = scc_tuneproc;
hwif->ide_dma_check = scc_config_drive_for_dma;
+ hwif->ide_dma_test_irq = scc_dma_test_irq;
hwif->drives[0].autotune = IDE_TUNE_AUTO;
hwif->drives[1].autotune = IDE_TUNE_AUTO;
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 2fe1d69..a4a9682 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -682,7 +682,34 @@
dev->irq = irq;
}
-#define LEGACY_IO_RESOURCE (IORESOURCE_IO | IORESOURCE_PCI_FIXED)
+static void change_legacy_io_resource(struct pci_dev * dev, unsigned index,
+ unsigned start, unsigned end)
+{
+ unsigned base = start & PCI_BASE_ADDRESS_IO_MASK;
+ unsigned len = (end | ~PCI_BASE_ADDRESS_IO_MASK) - base + 1;
+
+ /*
+ * Some X versions get confused when the BARs reported through
+ * /sys or /proc differ from those seen in config space, thus
+ * try to update the config space values, too.
+ */
+ if (!(pci_resource_flags(dev, index) & IORESOURCE_IO))
+ printk(KERN_WARNING "%s: cannot adjust BAR%u (not I/O)\n",
+ pci_name(dev), index);
+ else if (pci_resource_len(dev, index) != len)
+ printk(KERN_WARNING "%s: cannot adjust BAR%u (size %04X)\n",
+ pci_name(dev), index, (unsigned)pci_resource_len(dev, index));
+ else {
+ printk(KERN_INFO "%s: trying to change BAR%u from %04X to %04X\n",
+ pci_name(dev), index,
+ (unsigned)pci_resource_start(dev, index), base);
+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0 + index * 4, base);
+ }
+ pci_resource_start(dev, index) = start;
+ pci_resource_end(dev, index) = end;
+ pci_resource_flags(dev, index) =
+ IORESOURCE_IO | IORESOURCE_PCI_FIXED | PCI_BASE_ADDRESS_SPACE_IO;
+}
/**
* pci_setup_device - fill in class and map information of a device
@@ -735,20 +762,12 @@
u8 progif;
pci_read_config_byte(dev, PCI_CLASS_PROG, &progif);
if ((progif & 1) == 0) {
- dev->resource[0].start = 0x1F0;
- dev->resource[0].end = 0x1F7;
- dev->resource[0].flags = LEGACY_IO_RESOURCE;
- dev->resource[1].start = 0x3F6;
- dev->resource[1].end = 0x3F6;
- dev->resource[1].flags = LEGACY_IO_RESOURCE;
+ change_legacy_io_resource(dev, 0, 0x1F0, 0x1F7);
+ change_legacy_io_resource(dev, 1, 0x3F6, 0x3F6);
}
if ((progif & 4) == 0) {
- dev->resource[2].start = 0x170;
- dev->resource[2].end = 0x177;
- dev->resource[2].flags = LEGACY_IO_RESOURCE;
- dev->resource[3].start = 0x376;
- dev->resource[3].end = 0x376;
- dev->resource[3].flags = LEGACY_IO_RESOURCE;
+ change_legacy_io_resource(dev, 2, 0x170, 0x177);
+ change_legacy_io_resource(dev, 3, 0x376, 0x376);
}
}
break;
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 79c0282..34f2676 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -1359,7 +1359,8 @@
typedef struct ide_pio_timings_s {
int setup_time; /* Address setup (ns) minimum */
int active_time; /* Active pulse (ns) minimum */
- int cycle_time; /* Cycle time (ns) minimum = (setup + active + recovery) */
+ int cycle_time; /* Cycle time (ns) minimum = */
+ /* active + recovery (+ setup for some chips) */
} ide_pio_timings_t;
typedef struct ide_pio_data_s {