| /* |
| * OHCI HCD (Host Controller Driver) for USB. |
| * |
| * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> |
| * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net> |
| * |
| * This file is licenced under GPL |
| */ |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| /* |
| * OHCI Root Hub ... the nonsharable stuff |
| */ |
| |
| #define dbg_port(hc,label,num,value) \ |
| ohci_dbg (hc, \ |
| "%s roothub.portstatus [%d] " \ |
| "= 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s\n", \ |
| label, num, temp, \ |
| (temp & RH_PS_PRSC) ? " PRSC" : "", \ |
| (temp & RH_PS_OCIC) ? " OCIC" : "", \ |
| (temp & RH_PS_PSSC) ? " PSSC" : "", \ |
| (temp & RH_PS_PESC) ? " PESC" : "", \ |
| (temp & RH_PS_CSC) ? " CSC" : "", \ |
| \ |
| (temp & RH_PS_LSDA) ? " LSDA" : "", \ |
| (temp & RH_PS_PPS) ? " PPS" : "", \ |
| (temp & RH_PS_PRS) ? " PRS" : "", \ |
| (temp & RH_PS_POCI) ? " POCI" : "", \ |
| (temp & RH_PS_PSS) ? " PSS" : "", \ |
| \ |
| (temp & RH_PS_PES) ? " PES" : "", \ |
| (temp & RH_PS_CCS) ? " CCS" : "" \ |
| ); |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_PM |
| |
| #define OHCI_SCHED_ENABLES \ |
| (OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE) |
| |
| static void dl_done_list (struct ohci_hcd *, struct pt_regs *); |
| static void finish_unlinks (struct ohci_hcd *, u16 , struct pt_regs *); |
| static int ohci_restart (struct ohci_hcd *ohci); |
| |
| static int ohci_bus_suspend (struct usb_hcd *hcd) |
| { |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
| int status = 0; |
| unsigned long flags; |
| |
| spin_lock_irqsave (&ohci->lock, flags); |
| |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) { |
| spin_unlock_irqrestore (&ohci->lock, flags); |
| return -ESHUTDOWN; |
| } |
| |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); |
| switch (ohci->hc_control & OHCI_CTRL_HCFS) { |
| case OHCI_USB_RESUME: |
| ohci_dbg (ohci, "resume/suspend?\n"); |
| ohci->hc_control &= ~OHCI_CTRL_HCFS; |
| ohci->hc_control |= OHCI_USB_RESET; |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| /* FALL THROUGH */ |
| case OHCI_USB_RESET: |
| status = -EBUSY; |
| ohci_dbg (ohci, "needs reinit!\n"); |
| goto done; |
| case OHCI_USB_SUSPEND: |
| ohci_dbg (ohci, "already suspended\n"); |
| goto done; |
| } |
| ohci_dbg (ohci, "suspend root hub\n"); |
| |
| /* First stop any processing */ |
| if (ohci->hc_control & OHCI_SCHED_ENABLES) { |
| int limit; |
| |
| ohci->hc_control &= ~OHCI_SCHED_ENABLES; |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); |
| ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrstatus); |
| |
| /* sched disables take effect on the next frame, |
| * then the last WDH could take 6+ msec |
| */ |
| ohci_dbg (ohci, "stopping schedules ...\n"); |
| limit = 2000; |
| while (limit > 0) { |
| udelay (250); |
| limit =- 250; |
| if (ohci_readl (ohci, &ohci->regs->intrstatus) |
| & OHCI_INTR_SF) |
| break; |
| } |
| dl_done_list (ohci, NULL); |
| mdelay (7); |
| } |
| dl_done_list (ohci, NULL); |
| finish_unlinks (ohci, ohci_frame_no(ohci), NULL); |
| ohci_writel (ohci, ohci_readl (ohci, &ohci->regs->intrstatus), |
| &ohci->regs->intrstatus); |
| |
| /* maybe resume can wake root hub */ |
| if (device_may_wakeup(&ohci_to_hcd(ohci)->self.root_hub->dev)) |
| ohci->hc_control |= OHCI_CTRL_RWE; |
| else |
| ohci->hc_control &= ~OHCI_CTRL_RWE; |
| |
| /* Suspend hub ... this is the "global (to this bus) suspend" mode, |
| * which doesn't imply ports will first be individually suspended. |
| */ |
| ohci->hc_control &= ~OHCI_CTRL_HCFS; |
| ohci->hc_control |= OHCI_USB_SUSPEND; |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| |
| /* no resumes until devices finish suspending */ |
| ohci->next_statechange = jiffies + msecs_to_jiffies (5); |
| |
| done: |
| /* external suspend vs self autosuspend ... same effect */ |
| if (status == 0) |
| usb_hcd_suspend_root_hub(hcd); |
| spin_unlock_irqrestore (&ohci->lock, flags); |
| return status; |
| } |
| |
| static inline struct ed *find_head (struct ed *ed) |
| { |
| /* for bulk and control lists */ |
| while (ed->ed_prev) |
| ed = ed->ed_prev; |
| return ed; |
| } |
| |
| /* caller has locked the root hub */ |
| static int ohci_bus_resume (struct usb_hcd *hcd) |
| { |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
| u32 temp, enables; |
| int status = -EINPROGRESS; |
| unsigned long flags; |
| |
| if (time_before (jiffies, ohci->next_statechange)) |
| msleep(5); |
| |
| spin_lock_irqsave (&ohci->lock, flags); |
| |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) { |
| spin_unlock_irqrestore (&ohci->lock, flags); |
| return -ESHUTDOWN; |
| } |
| |
| |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); |
| |
| if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) { |
| /* this can happen after resuming a swsusp snapshot */ |
| if (hcd->state == HC_STATE_RESUMING) { |
| ohci_dbg (ohci, "BIOS/SMM active, control %03x\n", |
| ohci->hc_control); |
| status = -EBUSY; |
| /* this happens when pmcore resumes HC then root */ |
| } else { |
| ohci_dbg (ohci, "duplicate resume\n"); |
| status = 0; |
| } |
| } else switch (ohci->hc_control & OHCI_CTRL_HCFS) { |
| case OHCI_USB_SUSPEND: |
| ohci->hc_control &= ~(OHCI_CTRL_HCFS|OHCI_SCHED_ENABLES); |
| ohci->hc_control |= OHCI_USB_RESUME; |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| ohci_dbg (ohci, "resume root hub\n"); |
| break; |
| case OHCI_USB_RESUME: |
| /* HCFS changes sometime after INTR_RD */ |
| ohci_info (ohci, "wakeup\n"); |
| break; |
| case OHCI_USB_OPER: |
| /* this can happen after resuming a swsusp snapshot */ |
| ohci_dbg (ohci, "snapshot resume? reinit\n"); |
| status = -EBUSY; |
| break; |
| default: /* RESET, we lost power */ |
| ohci_dbg (ohci, "lost power\n"); |
| status = -EBUSY; |
| } |
| spin_unlock_irqrestore (&ohci->lock, flags); |
| if (status == -EBUSY) { |
| (void) ohci_init (ohci); |
| return ohci_restart (ohci); |
| } |
| if (status != -EINPROGRESS) |
| return status; |
| |
| temp = ohci->num_ports; |
| enables = 0; |
| while (temp--) { |
| u32 stat = ohci_readl (ohci, |
| &ohci->regs->roothub.portstatus [temp]); |
| |
| /* force global, not selective, resume */ |
| if (!(stat & RH_PS_PSS)) |
| continue; |
| ohci_writel (ohci, RH_PS_POCI, |
| &ohci->regs->roothub.portstatus [temp]); |
| } |
| |
| /* Some controllers (lucent erratum) need extra-long delays */ |
| msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1); |
| |
| temp = ohci_readl (ohci, &ohci->regs->control); |
| temp &= OHCI_CTRL_HCFS; |
| if (temp != OHCI_USB_RESUME) { |
| ohci_err (ohci, "controller won't resume\n"); |
| return -EBUSY; |
| } |
| |
| /* disable old schedule state, reinit from scratch */ |
| ohci_writel (ohci, 0, &ohci->regs->ed_controlhead); |
| ohci_writel (ohci, 0, &ohci->regs->ed_controlcurrent); |
| ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead); |
| ohci_writel (ohci, 0, &ohci->regs->ed_bulkcurrent); |
| ohci_writel (ohci, 0, &ohci->regs->ed_periodcurrent); |
| ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca); |
| |
| /* Sometimes PCI D3 suspend trashes frame timings ... */ |
| periodic_reinit (ohci); |
| |
| /* interrupts might have been disabled */ |
| ohci_writel (ohci, OHCI_INTR_INIT, &ohci->regs->intrenable); |
| if (ohci->ed_rm_list) |
| ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrenable); |
| ohci_writel (ohci, ohci_readl (ohci, &ohci->regs->intrstatus), |
| &ohci->regs->intrstatus); |
| |
| /* Then re-enable operations */ |
| ohci_writel (ohci, OHCI_USB_OPER, &ohci->regs->control); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| msleep (3); |
| |
| temp = ohci->hc_control; |
| temp &= OHCI_CTRL_RWC; |
| temp |= OHCI_CONTROL_INIT | OHCI_USB_OPER; |
| ohci->hc_control = temp; |
| ohci_writel (ohci, temp, &ohci->regs->control); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| |
| /* TRSMRCY */ |
| msleep (10); |
| |
| /* keep it alive for ~5x suspend + resume costs */ |
| ohci->next_statechange = jiffies + msecs_to_jiffies (250); |
| |
| /* maybe turn schedules back on */ |
| enables = 0; |
| temp = 0; |
| if (!ohci->ed_rm_list) { |
| if (ohci->ed_controltail) { |
| ohci_writel (ohci, |
| find_head (ohci->ed_controltail)->dma, |
| &ohci->regs->ed_controlhead); |
| enables |= OHCI_CTRL_CLE; |
| temp |= OHCI_CLF; |
| } |
| if (ohci->ed_bulktail) { |
| ohci_writel (ohci, find_head (ohci->ed_bulktail)->dma, |
| &ohci->regs->ed_bulkhead); |
| enables |= OHCI_CTRL_BLE; |
| temp |= OHCI_BLF; |
| } |
| } |
| if (hcd->self.bandwidth_isoc_reqs || hcd->self.bandwidth_int_reqs) |
| enables |= OHCI_CTRL_PLE|OHCI_CTRL_IE; |
| if (enables) { |
| ohci_dbg (ohci, "restarting schedules ... %08x\n", enables); |
| ohci->hc_control |= enables; |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); |
| if (temp) |
| ohci_writel (ohci, temp, &ohci->regs->cmdstatus); |
| (void) ohci_readl (ohci, &ohci->regs->control); |
| } |
| |
| return 0; |
| } |
| |
| #endif /* CONFIG_PM */ |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| /* build "status change" packet (one or two bytes) from HC registers */ |
| |
| static int |
| ohci_hub_status_data (struct usb_hcd *hcd, char *buf) |
| { |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
| int i, changed = 0, length = 1; |
| int can_suspend = device_may_wakeup(&hcd->self.root_hub->dev); |
| unsigned long flags; |
| |
| spin_lock_irqsave (&ohci->lock, flags); |
| |
| /* handle autosuspended root: finish resuming before |
| * letting khubd or root hub timer see state changes. |
| */ |
| if (unlikely((ohci->hc_control & OHCI_CTRL_HCFS) != OHCI_USB_OPER |
| || !HC_IS_RUNNING(hcd->state))) { |
| can_suspend = 0; |
| goto done; |
| } |
| |
| /* undocumented erratum seen on at least rev D */ |
| if ((ohci->flags & OHCI_QUIRK_AMD756) |
| && (roothub_a (ohci) & RH_A_NDP) > MAX_ROOT_PORTS) { |
| ohci_warn (ohci, "bogus NDP, rereads as NDP=%d\n", |
| ohci_readl (ohci, &ohci->regs->roothub.a) & RH_A_NDP); |
| /* retry later; "should not happen" */ |
| goto done; |
| } |
| |
| /* init status */ |
| if (roothub_status (ohci) & (RH_HS_LPSC | RH_HS_OCIC)) |
| buf [0] = changed = 1; |
| else |
| buf [0] = 0; |
| if (ohci->num_ports > 7) { |
| buf [1] = 0; |
| length++; |
| } |
| |
| /* look at each port */ |
| for (i = 0; i < ohci->num_ports; i++) { |
| u32 status = roothub_portstatus (ohci, i); |
| |
| if (status & (RH_PS_CSC | RH_PS_PESC | RH_PS_PSSC |
| | RH_PS_OCIC | RH_PS_PRSC)) { |
| changed = 1; |
| if (i < 7) |
| buf [0] |= 1 << (i + 1); |
| else |
| buf [1] |= 1 << (i - 7); |
| continue; |
| } |
| |
| /* can suspend if no ports are enabled; or if all all |
| * enabled ports are suspended AND remote wakeup is on. |
| */ |
| if (!(status & RH_PS_CCS)) |
| continue; |
| if ((status & RH_PS_PSS) && can_suspend) |
| continue; |
| can_suspend = 0; |
| } |
| done: |
| spin_unlock_irqrestore (&ohci->lock, flags); |
| |
| #ifdef CONFIG_PM |
| /* save power by suspending idle root hubs; |
| * INTR_RD wakes us when there's work |
| */ |
| if (can_suspend |
| && !changed |
| && !ohci->ed_rm_list |
| && ((OHCI_CTRL_HCFS | OHCI_SCHED_ENABLES) |
| & ohci->hc_control) |
| == OHCI_USB_OPER |
| && time_after (jiffies, ohci->next_statechange) |
| && usb_trylock_device (hcd->self.root_hub) == 0 |
| ) { |
| ohci_vdbg (ohci, "autosuspend\n"); |
| (void) ohci_bus_suspend (hcd); |
| usb_unlock_device (hcd->self.root_hub); |
| } |
| #endif |
| |
| return changed ? length : 0; |
| } |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| static void |
| ohci_hub_descriptor ( |
| struct ohci_hcd *ohci, |
| struct usb_hub_descriptor *desc |
| ) { |
| u32 rh = roothub_a (ohci); |
| u16 temp; |
| |
| desc->bDescriptorType = 0x29; |
| desc->bPwrOn2PwrGood = (rh & RH_A_POTPGT) >> 24; |
| desc->bHubContrCurrent = 0; |
| |
| desc->bNbrPorts = ohci->num_ports; |
| temp = 1 + (ohci->num_ports / 8); |
| desc->bDescLength = 7 + 2 * temp; |
| |
| temp = 0; |
| if (rh & RH_A_NPS) /* no power switching? */ |
| temp |= 0x0002; |
| if (rh & RH_A_PSM) /* per-port power switching? */ |
| temp |= 0x0001; |
| if (rh & RH_A_NOCP) /* no overcurrent reporting? */ |
| temp |= 0x0010; |
| else if (rh & RH_A_OCPM) /* per-port overcurrent reporting? */ |
| temp |= 0x0008; |
| desc->wHubCharacteristics = (__force __u16)cpu_to_hc16(ohci, temp); |
| |
| /* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */ |
| rh = roothub_b (ohci); |
| memset(desc->bitmap, 0xff, sizeof(desc->bitmap)); |
| desc->bitmap [0] = rh & RH_B_DR; |
| if (ohci->num_ports > 7) { |
| desc->bitmap [1] = (rh & RH_B_DR) >> 8; |
| desc->bitmap [2] = 0xff; |
| } else |
| desc->bitmap [1] = 0xff; |
| } |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_USB_OTG |
| |
| static int ohci_start_port_reset (struct usb_hcd *hcd, unsigned port) |
| { |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
| u32 status; |
| |
| if (!port) |
| return -EINVAL; |
| port--; |
| |
| /* start port reset before HNP protocol times out */ |
| status = ohci_readl(ohci, &ohci->regs->roothub.portstatus [port]); |
| if (!(status & RH_PS_CCS)) |
| return -ENODEV; |
| |
| /* khubd will finish the reset later */ |
| ohci_writel(ohci, RH_PS_PRS, &ohci->regs->roothub.portstatus [port]); |
| return 0; |
| } |
| |
| static void start_hnp(struct ohci_hcd *ohci); |
| |
| #else |
| |
| #define ohci_start_port_reset NULL |
| |
| #endif |
| |
| /*-------------------------------------------------------------------------*/ |
| |
| |
| /* See usb 7.1.7.5: root hubs must issue at least 50 msec reset signaling, |
| * not necessarily continuous ... to guard against resume signaling. |
| * The short timeout is safe for non-root hubs, and is backward-compatible |
| * with earlier Linux hosts. |
| */ |
| #ifdef CONFIG_USB_SUSPEND |
| #define PORT_RESET_MSEC 50 |
| #else |
| #define PORT_RESET_MSEC 10 |
| #endif |
| |
| /* this timer value might be vendor-specific ... */ |
| #define PORT_RESET_HW_MSEC 10 |
| |
| /* wrap-aware logic morphed from <linux/jiffies.h> */ |
| #define tick_before(t1,t2) ((s16)(((s16)(t1))-((s16)(t2))) < 0) |
| |
| /* called from some task, normally khubd */ |
| static inline void root_port_reset (struct ohci_hcd *ohci, unsigned port) |
| { |
| __hc32 __iomem *portstat = &ohci->regs->roothub.portstatus [port]; |
| u32 temp; |
| u16 now = ohci_readl(ohci, &ohci->regs->fmnumber); |
| u16 reset_done = now + PORT_RESET_MSEC; |
| |
| /* build a "continuous enough" reset signal, with up to |
| * 3msec gap between pulses. scheduler HZ==100 must work; |
| * this might need to be deadline-scheduled. |
| */ |
| do { |
| /* spin until any current reset finishes */ |
| for (;;) { |
| temp = ohci_readl (ohci, portstat); |
| if (!(temp & RH_PS_PRS)) |
| break; |
| udelay (500); |
| } |
| |
| if (!(temp & RH_PS_CCS)) |
| break; |
| if (temp & RH_PS_PRSC) |
| ohci_writel (ohci, RH_PS_PRSC, portstat); |
| |
| /* start the next reset, sleep till it's probably done */ |
| ohci_writel (ohci, RH_PS_PRS, portstat); |
| msleep(PORT_RESET_HW_MSEC); |
| now = ohci_readl(ohci, &ohci->regs->fmnumber); |
| } while (tick_before(now, reset_done)); |
| /* caller synchronizes using PRSC */ |
| } |
| |
| static int ohci_hub_control ( |
| struct usb_hcd *hcd, |
| u16 typeReq, |
| u16 wValue, |
| u16 wIndex, |
| char *buf, |
| u16 wLength |
| ) { |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); |
| int ports = hcd_to_bus (hcd)->root_hub->maxchild; |
| u32 temp; |
| int retval = 0; |
| |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) |
| return -ESHUTDOWN; |
| |
| switch (typeReq) { |
| case ClearHubFeature: |
| switch (wValue) { |
| case C_HUB_OVER_CURRENT: |
| ohci_writel (ohci, RH_HS_OCIC, |
| &ohci->regs->roothub.status); |
| case C_HUB_LOCAL_POWER: |
| break; |
| default: |
| goto error; |
| } |
| break; |
| case ClearPortFeature: |
| if (!wIndex || wIndex > ports) |
| goto error; |
| wIndex--; |
| |
| switch (wValue) { |
| case USB_PORT_FEAT_ENABLE: |
| temp = RH_PS_CCS; |
| break; |
| case USB_PORT_FEAT_C_ENABLE: |
| temp = RH_PS_PESC; |
| break; |
| case USB_PORT_FEAT_SUSPEND: |
| temp = RH_PS_POCI; |
| if ((ohci->hc_control & OHCI_CTRL_HCFS) |
| != OHCI_USB_OPER) |
| usb_hcd_resume_root_hub(hcd); |
| break; |
| case USB_PORT_FEAT_C_SUSPEND: |
| temp = RH_PS_PSSC; |
| break; |
| case USB_PORT_FEAT_POWER: |
| temp = RH_PS_LSDA; |
| break; |
| case USB_PORT_FEAT_C_CONNECTION: |
| temp = RH_PS_CSC; |
| break; |
| case USB_PORT_FEAT_C_OVER_CURRENT: |
| temp = RH_PS_OCIC; |
| break; |
| case USB_PORT_FEAT_C_RESET: |
| temp = RH_PS_PRSC; |
| break; |
| default: |
| goto error; |
| } |
| ohci_writel (ohci, temp, |
| &ohci->regs->roothub.portstatus [wIndex]); |
| // ohci_readl (ohci, &ohci->regs->roothub.portstatus [wIndex]); |
| break; |
| case GetHubDescriptor: |
| ohci_hub_descriptor (ohci, (struct usb_hub_descriptor *) buf); |
| break; |
| case GetHubStatus: |
| temp = roothub_status (ohci) & ~(RH_HS_CRWE | RH_HS_DRWE); |
| *(__le32 *) buf = cpu_to_le32 (temp); |
| break; |
| case GetPortStatus: |
| if (!wIndex || wIndex > ports) |
| goto error; |
| wIndex--; |
| temp = roothub_portstatus (ohci, wIndex); |
| *(__le32 *) buf = cpu_to_le32 (temp); |
| |
| #ifndef OHCI_VERBOSE_DEBUG |
| if (*(u16*)(buf+2)) /* only if wPortChange is interesting */ |
| #endif |
| dbg_port (ohci, "GetStatus", wIndex, temp); |
| break; |
| case SetHubFeature: |
| switch (wValue) { |
| case C_HUB_OVER_CURRENT: |
| // FIXME: this can be cleared, yes? |
| case C_HUB_LOCAL_POWER: |
| break; |
| default: |
| goto error; |
| } |
| break; |
| case SetPortFeature: |
| if (!wIndex || wIndex > ports) |
| goto error; |
| wIndex--; |
| switch (wValue) { |
| case USB_PORT_FEAT_SUSPEND: |
| #ifdef CONFIG_USB_OTG |
| if (hcd->self.otg_port == (wIndex + 1) |
| && hcd->self.b_hnp_enable) |
| start_hnp(ohci); |
| else |
| #endif |
| ohci_writel (ohci, RH_PS_PSS, |
| &ohci->regs->roothub.portstatus [wIndex]); |
| break; |
| case USB_PORT_FEAT_POWER: |
| ohci_writel (ohci, RH_PS_PPS, |
| &ohci->regs->roothub.portstatus [wIndex]); |
| break; |
| case USB_PORT_FEAT_RESET: |
| root_port_reset (ohci, wIndex); |
| break; |
| default: |
| goto error; |
| } |
| break; |
| |
| default: |
| error: |
| /* "protocol stall" on error */ |
| retval = -EPIPE; |
| } |
| return retval; |
| } |
| |