[SCSI] qla2xxx: Update FCP priority information to firmware before sending IOs
The FCP priority info was not being updated properly in certain situations.
Here are the changes that needs to be done to take care of this issue:
1. No need to check fcport->state for FCS_UNCONFIGURED in
qla24xx_update_fcport_fcp_prio(), since an invalid loop id check is
already performed which is sufficient.
2. Add the missing qla24xx_update_fcport_fcp_prio() function call
within qla2x00_update_fcport() function, so that the priority info
is updated on every port addition or change.
3. Perform proper adapter types checking.
4. Other changes, associated with DEBUG/printk's and parameter passing.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c
index e9b800e..c8ca25a 100644
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
@@ -2928,6 +2928,7 @@
fcport->flags &= ~(FCF_LOGIN_NEEDED | FCF_ASYNC_SENT);
qla2x00_iidma_fcport(vha, fcport);
+ qla24xx_update_fcport_fcp_prio(vha, fcport);
qla2x00_reg_remote_port(vha, fcport);
atomic_set(&fcport->state, FCS_ONLINE);
}
@@ -5473,7 +5474,7 @@
* the tag (priority) value is returned.
*
* Input:
- * ha = adapter block po
+ * vha = scsi host structure pointer.
* fcport = port structure pointer.
*
* Return:
@@ -5567,7 +5568,7 @@
* Activates fcp priority for the logged in fc port
*
* Input:
- * ha = adapter block pointer.
+ * vha = scsi host structure pointer.
* fcp = port structure pointer.
*
* Return:
@@ -5577,25 +5578,24 @@
* Kernel context.
*/
int
-qla24xx_update_fcport_fcp_prio(scsi_qla_host_t *ha, fc_port_t *fcport)
+qla24xx_update_fcport_fcp_prio(scsi_qla_host_t *vha, fc_port_t *fcport)
{
int ret;
uint8_t priority;
uint16_t mb[5];
- if (atomic_read(&fcport->state) == FCS_UNCONFIGURED ||
- fcport->port_type != FCT_TARGET ||
- fcport->loop_id == FC_NO_LOOP_ID)
+ if (fcport->port_type != FCT_TARGET ||
+ fcport->loop_id == FC_NO_LOOP_ID)
return QLA_FUNCTION_FAILED;
- priority = qla24xx_get_fcp_prio(ha, fcport);
- ret = qla24xx_set_fcp_prio(ha, fcport->loop_id, priority, mb);
+ priority = qla24xx_get_fcp_prio(vha, fcport);
+ ret = qla24xx_set_fcp_prio(vha, fcport->loop_id, priority, mb);
if (ret == QLA_SUCCESS)
fcport->fcp_prio = priority;
else
DEBUG2(printk(KERN_WARNING
"scsi(%ld): Unable to activate fcp priority, "
- " ret=0x%x\n", ha->host_no, ret));
+ " ret=0x%x\n", vha->host_no, ret));
return ret;
}