[ARM] Kirkwood: update LED support for Network Space v2
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c
index 9f20c8d..d26bf32 100644
--- a/arch/arm/mach-kirkwood/netspace_v2-setup.c
+++ b/arch/arm/mach-kirkwood/netspace_v2-setup.c
@@ -39,6 +39,7 @@
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/kirkwood.h>
+#include <mach/leds-ns2.h>
#include <plat/time.h>
#include "common.h"
#include "mpp.h"
@@ -172,36 +173,12 @@
* GPIO LEDs
****************************************************************************/
-/*
- * The blue front LED is wired to a CPLD and can blink in relation with the
- * SATA activity.
- *
- * The following array detail the different LED registers and the combination
- * of their possible values:
- *
- * cmd_led | slow_led | /SATA active | LED state
- * | | |
- * 1 | 0 | x | off
- * - | 1 | x | on
- * 0 | 0 | 1 | on
- * 0 | 0 | 0 | blink (rate 300ms)
- */
-
#define NETSPACE_V2_GPIO_RED_LED 12
-#define NETSPACE_V2_GPIO_BLUE_LED_SLOW 29
-#define NETSPACE_V2_GPIO_BLUE_LED_CMD 30
-
static struct gpio_led netspace_v2_gpio_led_pins[] = {
{
- .name = "ns_v2:blue:sata",
- .default_trigger = "default-on",
- .gpio = NETSPACE_V2_GPIO_BLUE_LED_CMD,
- .active_low = 1,
- },
- {
- .name = "ns_v2:red:fail",
- .gpio = NETSPACE_V2_GPIO_RED_LED,
+ .name = "ns_v2:red:fail",
+ .gpio = NETSPACE_V2_GPIO_RED_LED,
},
};
@@ -218,22 +195,33 @@
},
};
-static void __init netspace_v2_gpio_leds_init(void)
-{
- int err;
+/*****************************************************************************
+ * Dual-GPIO CPLD LEDs
+ ****************************************************************************/
- /* Configure register slow_led to allow SATA activity LED blinking */
- err = gpio_request(NETSPACE_V2_GPIO_BLUE_LED_SLOW, "blue LED slow");
- if (err == 0) {
- err = gpio_direction_output(NETSPACE_V2_GPIO_BLUE_LED_SLOW, 0);
- if (err)
- gpio_free(NETSPACE_V2_GPIO_BLUE_LED_SLOW);
- }
- if (err)
- pr_err("netspace_v2: failed to configure blue LED slow GPIO\n");
+#define NETSPACE_V2_GPIO_BLUE_LED_SLOW 29
+#define NETSPACE_V2_GPIO_BLUE_LED_CMD 30
- platform_device_register(&netspace_v2_gpio_leds);
-}
+static struct ns2_led netspace_v2_led_pins[] = {
+ {
+ .name = "ns_v2:blue:sata",
+ .cmd = NETSPACE_V2_GPIO_BLUE_LED_CMD,
+ .slow = NETSPACE_V2_GPIO_BLUE_LED_SLOW,
+ },
+};
+
+static struct ns2_led_platform_data netspace_v2_leds_data = {
+ .num_leds = ARRAY_SIZE(netspace_v2_led_pins),
+ .leds = netspace_v2_led_pins,
+};
+
+static struct platform_device netspace_v2_leds = {
+ .name = "leds-ns2",
+ .id = -1,
+ .dev = {
+ .platform_data = &netspace_v2_leds_data,
+ },
+};
/*****************************************************************************
* Timer
@@ -316,7 +304,8 @@
i2c_register_board_info(0, netspace_v2_i2c_info,
ARRAY_SIZE(netspace_v2_i2c_info));
- netspace_v2_gpio_leds_init();
+ platform_device_register(&netspace_v2_leds);
+ platform_device_register(&netspace_v2_gpio_leds);
platform_device_register(&netspace_v2_gpio_buttons);
if (gpio_request(NETSPACE_V2_GPIO_POWER_OFF, "power-off") == 0 &&