| /* |
| * linux/drivers/mmc/host/sdhci.h - Secure Digital Host Controller Interface driver |
| * |
| * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or (at |
| * your option) any later version. |
| */ |
| |
| #include <linux/scatterlist.h> |
| #include <linux/compiler.h> |
| #include <linux/types.h> |
| #include <linux/io.h> |
| |
| /* |
| * Controller registers |
| */ |
| |
| #define SDHCI_DMA_ADDRESS 0x00 |
| |
| #define SDHCI_BLOCK_SIZE 0x04 |
| #define SDHCI_MAKE_BLKSZ(dma, blksz) (((dma & 0x7) << 12) | (blksz & 0xFFF)) |
| |
| #define SDHCI_BLOCK_COUNT 0x06 |
| |
| #define SDHCI_ARGUMENT 0x08 |
| |
| #define SDHCI_TRANSFER_MODE 0x0C |
| #define SDHCI_TRNS_DMA 0x01 |
| #define SDHCI_TRNS_BLK_CNT_EN 0x02 |
| #define SDHCI_TRNS_ACMD12 0x04 |
| #define SDHCI_TRNS_READ 0x10 |
| #define SDHCI_TRNS_MULTI 0x20 |
| |
| #define SDHCI_COMMAND 0x0E |
| #define SDHCI_CMD_RESP_MASK 0x03 |
| #define SDHCI_CMD_CRC 0x08 |
| #define SDHCI_CMD_INDEX 0x10 |
| #define SDHCI_CMD_DATA 0x20 |
| |
| #define SDHCI_CMD_RESP_NONE 0x00 |
| #define SDHCI_CMD_RESP_LONG 0x01 |
| #define SDHCI_CMD_RESP_SHORT 0x02 |
| #define SDHCI_CMD_RESP_SHORT_BUSY 0x03 |
| |
| #define SDHCI_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff)) |
| |
| #define SDHCI_RESPONSE 0x10 |
| |
| #define SDHCI_BUFFER 0x20 |
| |
| #define SDHCI_PRESENT_STATE 0x24 |
| #define SDHCI_CMD_INHIBIT 0x00000001 |
| #define SDHCI_DATA_INHIBIT 0x00000002 |
| #define SDHCI_DOING_WRITE 0x00000100 |
| #define SDHCI_DOING_READ 0x00000200 |
| #define SDHCI_SPACE_AVAILABLE 0x00000400 |
| #define SDHCI_DATA_AVAILABLE 0x00000800 |
| #define SDHCI_CARD_PRESENT 0x00010000 |
| #define SDHCI_WRITE_PROTECT 0x00080000 |
| |
| #define SDHCI_HOST_CONTROL 0x28 |
| #define SDHCI_CTRL_LED 0x01 |
| #define SDHCI_CTRL_4BITBUS 0x02 |
| #define SDHCI_CTRL_HISPD 0x04 |
| #define SDHCI_CTRL_DMA_MASK 0x18 |
| #define SDHCI_CTRL_SDMA 0x00 |
| #define SDHCI_CTRL_ADMA1 0x08 |
| #define SDHCI_CTRL_ADMA32 0x10 |
| #define SDHCI_CTRL_ADMA64 0x18 |
| |
| #define SDHCI_POWER_CONTROL 0x29 |
| #define SDHCI_POWER_ON 0x01 |
| #define SDHCI_POWER_180 0x0A |
| #define SDHCI_POWER_300 0x0C |
| #define SDHCI_POWER_330 0x0E |
| |
| #define SDHCI_BLOCK_GAP_CONTROL 0x2A |
| |
| #define SDHCI_WAKE_UP_CONTROL 0x2B |
| |
| #define SDHCI_CLOCK_CONTROL 0x2C |
| #define SDHCI_DIVIDER_SHIFT 8 |
| #define SDHCI_CLOCK_CARD_EN 0x0004 |
| #define SDHCI_CLOCK_INT_STABLE 0x0002 |
| #define SDHCI_CLOCK_INT_EN 0x0001 |
| |
| #define SDHCI_TIMEOUT_CONTROL 0x2E |
| |
| #define SDHCI_SOFTWARE_RESET 0x2F |
| #define SDHCI_RESET_ALL 0x01 |
| #define SDHCI_RESET_CMD 0x02 |
| #define SDHCI_RESET_DATA 0x04 |
| |
| #define SDHCI_INT_STATUS 0x30 |
| #define SDHCI_INT_ENABLE 0x34 |
| #define SDHCI_SIGNAL_ENABLE 0x38 |
| #define SDHCI_INT_RESPONSE 0x00000001 |
| #define SDHCI_INT_DATA_END 0x00000002 |
| #define SDHCI_INT_DMA_END 0x00000008 |
| #define SDHCI_INT_SPACE_AVAIL 0x00000010 |
| #define SDHCI_INT_DATA_AVAIL 0x00000020 |
| #define SDHCI_INT_CARD_INSERT 0x00000040 |
| #define SDHCI_INT_CARD_REMOVE 0x00000080 |
| #define SDHCI_INT_CARD_INT 0x00000100 |
| #define SDHCI_INT_ERROR 0x00008000 |
| #define SDHCI_INT_TIMEOUT 0x00010000 |
| #define SDHCI_INT_CRC 0x00020000 |
| #define SDHCI_INT_END_BIT 0x00040000 |
| #define SDHCI_INT_INDEX 0x00080000 |
| #define SDHCI_INT_DATA_TIMEOUT 0x00100000 |
| #define SDHCI_INT_DATA_CRC 0x00200000 |
| #define SDHCI_INT_DATA_END_BIT 0x00400000 |
| #define SDHCI_INT_BUS_POWER 0x00800000 |
| #define SDHCI_INT_ACMD12ERR 0x01000000 |
| #define SDHCI_INT_ADMA_ERROR 0x02000000 |
| |
| #define SDHCI_INT_NORMAL_MASK 0x00007FFF |
| #define SDHCI_INT_ERROR_MASK 0xFFFF8000 |
| |
| #define SDHCI_INT_CMD_MASK (SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \ |
| SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX) |
| #define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \ |
| SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \ |
| SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \ |
| SDHCI_INT_DATA_END_BIT | SDHCI_ADMA_ERROR) |
| #define SDHCI_INT_ALL_MASK ((unsigned int)-1) |
| |
| #define SDHCI_ACMD12_ERR 0x3C |
| |
| /* 3E-3F reserved */ |
| |
| #define SDHCI_CAPABILITIES 0x40 |
| #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F |
| #define SDHCI_TIMEOUT_CLK_SHIFT 0 |
| #define SDHCI_TIMEOUT_CLK_UNIT 0x00000080 |
| #define SDHCI_CLOCK_BASE_MASK 0x00003F00 |
| #define SDHCI_CLOCK_BASE_SHIFT 8 |
| #define SDHCI_MAX_BLOCK_MASK 0x00030000 |
| #define SDHCI_MAX_BLOCK_SHIFT 16 |
| #define SDHCI_CAN_DO_ADMA2 0x00080000 |
| #define SDHCI_CAN_DO_ADMA1 0x00100000 |
| #define SDHCI_CAN_DO_HISPD 0x00200000 |
| #define SDHCI_CAN_DO_DMA 0x00400000 |
| #define SDHCI_CAN_VDD_330 0x01000000 |
| #define SDHCI_CAN_VDD_300 0x02000000 |
| #define SDHCI_CAN_VDD_180 0x04000000 |
| #define SDHCI_CAN_64BIT 0x10000000 |
| |
| /* 44-47 reserved for more caps */ |
| |
| #define SDHCI_MAX_CURRENT 0x48 |
| |
| /* 4C-4F reserved for more max current */ |
| |
| #define SDHCI_SET_ACMD12_ERROR 0x50 |
| #define SDHCI_SET_INT_ERROR 0x52 |
| |
| #define SDHCI_ADMA_ERROR 0x54 |
| |
| /* 55-57 reserved */ |
| |
| #define SDHCI_ADMA_ADDRESS 0x58 |
| |
| /* 60-FB reserved */ |
| |
| #define SDHCI_SLOT_INT_STATUS 0xFC |
| |
| #define SDHCI_HOST_VERSION 0xFE |
| #define SDHCI_VENDOR_VER_MASK 0xFF00 |
| #define SDHCI_VENDOR_VER_SHIFT 8 |
| #define SDHCI_SPEC_VER_MASK 0x00FF |
| #define SDHCI_SPEC_VER_SHIFT 0 |
| #define SDHCI_SPEC_100 0 |
| #define SDHCI_SPEC_200 1 |
| |
| struct sdhci_ops; |
| |
| struct sdhci_host { |
| /* Data set by hardware interface driver */ |
| const char *hw_name; /* Hardware bus name */ |
| |
| unsigned int quirks; /* Deviations from spec. */ |
| |
| /* Controller doesn't honor resets unless we touch the clock register */ |
| #define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0) |
| /* Controller has bad caps bits, but really supports DMA */ |
| #define SDHCI_QUIRK_FORCE_DMA (1<<1) |
| /* Controller doesn't like to be reset when there is no card inserted. */ |
| #define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2) |
| /* Controller doesn't like clearing the power reg before a change */ |
| #define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3) |
| /* Controller has flaky internal state so reset it on each ios change */ |
| #define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) |
| /* Controller has an unusable DMA engine */ |
| #define SDHCI_QUIRK_BROKEN_DMA (1<<5) |
| /* Controller has an unusable ADMA engine */ |
| #define SDHCI_QUIRK_BROKEN_ADMA (1<<6) |
| /* Controller can only DMA from 32-bit aligned addresses */ |
| #define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<7) |
| /* Controller can only DMA chunk sizes that are a multiple of 32 bits */ |
| #define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<8) |
| /* Controller can only ADMA chunks that are a multiple of 32 bits */ |
| #define SDHCI_QUIRK_32BIT_ADMA_SIZE (1<<9) |
| /* Controller needs to be reset after each request to stay stable */ |
| #define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<10) |
| /* Controller needs voltage and power writes to happen separately */ |
| #define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11) |
| /* Controller provides an incorrect timeout value for transfers */ |
| #define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12) |
| /* Controller has an issue with buffer bits for small transfers */ |
| #define SDHCI_QUIRK_BROKEN_SMALL_PIO (1<<13) |
| /* Controller does not provide transfer-complete interrupt when not busy */ |
| #define SDHCI_QUIRK_NO_BUSY_IRQ (1<<14) |
| /* Controller has unreliable card detection */ |
| #define SDHCI_QUIRK_BROKEN_CARD_DETECTION (1<<15) |
| /* Controller reports inverted write-protect state */ |
| #define SDHCI_QUIRK_INVERTED_WRITE_PROTECT (1<<16) |
| /* Controller has nonstandard clock management */ |
| #define SDHCI_QUIRK_NONSTANDARD_CLOCK (1<<17) |
| /* Controller does not like fast PIO transfers */ |
| #define SDHCI_QUIRK_PIO_NEEDS_DELAY (1<<18) |
| /* Controller losing signal/interrupt enable states after reset */ |
| #define SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET (1<<19) |
| /* Controller has to be forced to use block size of 2048 bytes */ |
| #define SDHCI_QUIRK_FORCE_BLK_SZ_2048 (1<<20) |
| /* Controller cannot do multi-block transfers */ |
| #define SDHCI_QUIRK_NO_MULTIBLOCK (1<<21) |
| /* Controller can only handle 1-bit data transfers */ |
| #define SDHCI_QUIRK_FORCE_1_BIT_DATA (1<<22) |
| /* Controller needs 10ms delay between applying power and clock */ |
| #define SDHCI_QUIRK_DELAY_AFTER_POWER (1<<23) |
| |
| int irq; /* Device IRQ */ |
| void __iomem * ioaddr; /* Mapped address */ |
| |
| const struct sdhci_ops *ops; /* Low level hw interface */ |
| |
| /* Internal data */ |
| struct mmc_host *mmc; /* MMC structure */ |
| u64 dma_mask; /* custom DMA mask */ |
| |
| #if defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE) |
| struct led_classdev led; /* LED control */ |
| char led_name[32]; |
| #endif |
| |
| spinlock_t lock; /* Mutex */ |
| |
| int flags; /* Host attributes */ |
| #define SDHCI_USE_DMA (1<<0) /* Host is DMA capable */ |
| #define SDHCI_USE_ADMA (1<<1) /* Host is ADMA capable */ |
| #define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */ |
| #define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */ |
| |
| unsigned int version; /* SDHCI spec. version */ |
| |
| unsigned int max_clk; /* Max possible freq (MHz) */ |
| unsigned int timeout_clk; /* Timeout freq (KHz) */ |
| |
| unsigned int clock; /* Current clock (MHz) */ |
| u8 pwr; /* Current voltage */ |
| |
| struct mmc_request *mrq; /* Current request */ |
| struct mmc_command *cmd; /* Current command */ |
| struct mmc_data *data; /* Current data request */ |
| unsigned int data_early:1; /* Data finished before cmd */ |
| |
| struct sg_mapping_iter sg_miter; /* SG state for PIO */ |
| unsigned int blocks; /* remaining PIO blocks */ |
| |
| int sg_count; /* Mapped sg entries */ |
| |
| u8 *adma_desc; /* ADMA descriptor table */ |
| u8 *align_buffer; /* Bounce buffer */ |
| |
| dma_addr_t adma_addr; /* Mapped ADMA descr. table */ |
| dma_addr_t align_addr; /* Mapped bounce buffer */ |
| |
| struct tasklet_struct card_tasklet; /* Tasklet structures */ |
| struct tasklet_struct finish_tasklet; |
| |
| struct timer_list timer; /* Timer for timeouts */ |
| |
| unsigned long private[0] ____cacheline_aligned; |
| }; |
| |
| |
| struct sdhci_ops { |
| #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS |
| u32 (*readl)(struct sdhci_host *host, int reg); |
| u16 (*readw)(struct sdhci_host *host, int reg); |
| u8 (*readb)(struct sdhci_host *host, int reg); |
| void (*writel)(struct sdhci_host *host, u32 val, int reg); |
| void (*writew)(struct sdhci_host *host, u16 val, int reg); |
| void (*writeb)(struct sdhci_host *host, u8 val, int reg); |
| #endif |
| |
| void (*set_clock)(struct sdhci_host *host, unsigned int clock); |
| |
| int (*enable_dma)(struct sdhci_host *host); |
| unsigned int (*get_max_clock)(struct sdhci_host *host); |
| unsigned int (*get_timeout_clock)(struct sdhci_host *host); |
| }; |
| |
| #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS |
| |
| static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg) |
| { |
| if (unlikely(host->ops->writel)) |
| host->ops->writel(host, val, reg); |
| else |
| writel(val, host->ioaddr + reg); |
| } |
| |
| static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg) |
| { |
| if (unlikely(host->ops->writew)) |
| host->ops->writew(host, val, reg); |
| else |
| writew(val, host->ioaddr + reg); |
| } |
| |
| static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg) |
| { |
| if (unlikely(host->ops->writeb)) |
| host->ops->writeb(host, val, reg); |
| else |
| writeb(val, host->ioaddr + reg); |
| } |
| |
| static inline u32 sdhci_readl(struct sdhci_host *host, int reg) |
| { |
| if (unlikely(host->ops->readl)) |
| return host->ops->readl(host, reg); |
| else |
| return readl(host->ioaddr + reg); |
| } |
| |
| static inline u16 sdhci_readw(struct sdhci_host *host, int reg) |
| { |
| if (unlikely(host->ops->readw)) |
| return host->ops->readw(host, reg); |
| else |
| return readw(host->ioaddr + reg); |
| } |
| |
| static inline u8 sdhci_readb(struct sdhci_host *host, int reg) |
| { |
| if (unlikely(host->ops->readb)) |
| return host->ops->readb(host, reg); |
| else |
| return readb(host->ioaddr + reg); |
| } |
| |
| #else |
| |
| static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg) |
| { |
| writel(val, host->ioaddr + reg); |
| } |
| |
| static inline void sdhci_writew(struct sdhci_host *host, u16 val, int reg) |
| { |
| writew(val, host->ioaddr + reg); |
| } |
| |
| static inline void sdhci_writeb(struct sdhci_host *host, u8 val, int reg) |
| { |
| writeb(val, host->ioaddr + reg); |
| } |
| |
| static inline u32 sdhci_readl(struct sdhci_host *host, int reg) |
| { |
| return readl(host->ioaddr + reg); |
| } |
| |
| static inline u16 sdhci_readw(struct sdhci_host *host, int reg) |
| { |
| return readw(host->ioaddr + reg); |
| } |
| |
| static inline u8 sdhci_readb(struct sdhci_host *host, int reg) |
| { |
| return readb(host->ioaddr + reg); |
| } |
| |
| #endif /* CONFIG_MMC_SDHCI_IO_ACCESSORS */ |
| |
| extern struct sdhci_host *sdhci_alloc_host(struct device *dev, |
| size_t priv_size); |
| extern void sdhci_free_host(struct sdhci_host *host); |
| |
| static inline void *sdhci_priv(struct sdhci_host *host) |
| { |
| return (void *)host->private; |
| } |
| |
| extern int sdhci_add_host(struct sdhci_host *host); |
| extern void sdhci_remove_host(struct sdhci_host *host, int dead); |
| |
| #ifdef CONFIG_PM |
| extern int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state); |
| extern int sdhci_resume_host(struct sdhci_host *host); |
| #endif |