netxen: firmware init fix
o Fix order or rom register writes.
o Reduce udelays when writing rom registers.
This cuts the firmware init time by 40%.
o Do not reset core/memory clocks when reinitializing driver.
Firmware willl handle this when initialized.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c
index c0e06a6..a320364 100644
--- a/drivers/net/netxen/netxen_nic_init.c
+++ b/drivers/net/netxen/netxen_nic_init.c
@@ -439,6 +439,8 @@
long timeout = 0;
long done = 0;
+ cond_resched();
+
while (done == 0) {
done = netxen_nic_reg_read(adapter, NETXEN_ROMUSB_GLB_STATUS);
done &= 2;
@@ -533,12 +535,9 @@
static int do_rom_fast_read(struct netxen_adapter *adapter,
int addr, int *valp)
{
- cond_resched();
-
netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ADDRESS, addr);
- netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ABYTE_CNT, 3);
- udelay(100); /* prevent bursting on CRB */
netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_DUMMY_BYTE_CNT, 0);
+ netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ABYTE_CNT, 3);
netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_INSTR_OPCODE, 0xb);
if (netxen_wait_rom_done(adapter)) {
printk("Error waiting for rom done\n");
@@ -546,7 +545,7 @@
}
/* reset abyte_cnt and dummy_byte_cnt */
netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_ABYTE_CNT, 0);
- udelay(100); /* prevent bursting on CRB */
+ udelay(10);
netxen_nic_reg_write(adapter, NETXEN_ROMUSB_ROM_DUMMY_BYTE_CNT, 0);
*valp = netxen_nic_reg_read(adapter, NETXEN_ROMUSB_ROM_RDATA);
@@ -884,14 +883,16 @@
int netxen_pinit_from_rom(struct netxen_adapter *adapter, int verbose)
{
int addr, val;
- int i, init_delay = 0;
+ int i, n, init_delay = 0;
struct crb_addr_pair *buf;
- unsigned offset, n;
+ unsigned offset;
u32 off;
/* resetall */
+ rom_lock(adapter);
netxen_crb_writelit_adapter(adapter, NETXEN_ROMUSB_GLB_SW_RESET,
0xffffffff);
+ netxen_rom_unlock(adapter);
if (verbose) {
if (netxen_rom_fast_read(adapter, NETXEN_BOARDTYPE, &val) == 0)
@@ -910,7 +911,7 @@
if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) {
if (netxen_rom_fast_read(adapter, 0, &n) != 0 ||
- (n != 0xcafecafeUL) ||
+ (n != 0xcafecafe) ||
netxen_rom_fast_read(adapter, 4, &n) != 0) {
printk(KERN_ERR "%s: ERROR Reading crb_init area: "
"n: %08x\n", netxen_nic_driver_name, n);
@@ -975,6 +976,14 @@
/* do not reset PCI */
if (off == (ROMUSB_GLB + 0xbc))
continue;
+ if (off == (ROMUSB_GLB + 0xa8))
+ continue;
+ if (off == (ROMUSB_GLB + 0xc8)) /* core clock */
+ continue;
+ if (off == (ROMUSB_GLB + 0x24)) /* MN clock */
+ continue;
+ if (off == (ROMUSB_GLB + 0x1c)) /* MS clock */
+ continue;
if (off == (NETXEN_CRB_PEG_NET_1 + 0x18))
buf[i].data = 0x1020;
/* skip the function enable register */
@@ -992,23 +1001,21 @@
continue;
}
+ init_delay = 1;
/* After writing this register, HW needs time for CRB */
/* to quiet down (else crb_window returns 0xffffffff) */
if (off == NETXEN_ROMUSB_GLB_SW_RESET) {
- init_delay = 1;
+ init_delay = 1000;
if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) {
/* hold xdma in reset also */
buf[i].data = NETXEN_NIC_XDMA_RESET;
+ buf[i].data = 0x8000ff;
}
}
adapter->hw_write_wx(adapter, off, &buf[i].data, 4);
- if (init_delay == 1) {
- msleep(1000);
- init_delay = 0;
- }
- msleep(1);
+ msleep(init_delay);
}
kfree(buf);