| /* |
| * Copyright (c) 1999-2003 Petko Manolov - Petkan (petkan@users.sourceforge.net) |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as published |
| * by the Free Software Foundation. |
| */ |
| |
| |
| #ifndef PEGASUS_DEV |
| |
| #define PEGASUS_II 0x80000000 |
| #define HAS_HOME_PNA 0x40000000 |
| |
| #define PEGASUS_MTU 1536 |
| #define RX_SKBS 4 |
| |
| #define EPROM_WRITE 0x01 |
| #define EPROM_READ 0x02 |
| #define EPROM_DONE 0x04 |
| #define EPROM_WR_ENABLE 0x10 |
| #define EPROM_LOAD 0x20 |
| |
| #define PHY_DONE 0x80 |
| #define PHY_READ 0x40 |
| #define PHY_WRITE 0x20 |
| #define DEFAULT_GPIO_RESET 0x24 |
| #define DEFAULT_GPIO_SET 0x26 |
| |
| #define PEGASUS_PRESENT 0x00000001 |
| #define PEGASUS_TX_BUSY 0x00000004 |
| #define PEGASUS_RX_BUSY 0x00000008 |
| #define CTRL_URB_RUNNING 0x00000010 |
| #define CTRL_URB_SLEEP 0x00000020 |
| #define PEGASUS_UNPLUG 0x00000040 |
| #define PEGASUS_RX_URB_FAIL 0x00000080 |
| #define ETH_REGS_CHANGE 0x40000000 |
| #define ETH_REGS_CHANGED 0x80000000 |
| |
| #define RX_MULTICAST 2 |
| #define RX_PROMISCUOUS 4 |
| |
| #define REG_TIMEOUT (HZ) |
| #define PEGASUS_TX_TIMEOUT (HZ*10) |
| |
| #define TX_UNDERRUN 0x80 |
| #define EXCESSIVE_COL 0x40 |
| #define LATE_COL 0x20 |
| #define NO_CARRIER 0x10 |
| #define LOSS_CARRIER 0x08 |
| #define JABBER_TIMEOUT 0x04 |
| |
| #define LINK_STATUS 0x01 |
| |
| #define PEGASUS_REQT_READ 0xc0 |
| #define PEGASUS_REQT_WRITE 0x40 |
| #define PEGASUS_REQ_GET_REGS 0xf0 |
| #define PEGASUS_REQ_SET_REGS 0xf1 |
| #define PEGASUS_REQ_SET_REG PEGASUS_REQ_SET_REGS |
| |
| enum pegasus_registers { |
| EthCtrl0 = 0, |
| EthCtrl1 = 1, |
| EthCtrl2 = 2, |
| EthID = 0x10, |
| Reg1d = 0x1d, |
| EpromOffset = 0x20, |
| EpromData = 0x21, /* 0x21 low, 0x22 high byte */ |
| EpromCtrl = 0x23, |
| PhyAddr = 0x25, |
| PhyData = 0x26, /* 0x26 low, 0x27 high byte */ |
| PhyCtrl = 0x28, |
| UsbStst = 0x2a, |
| EthTxStat0 = 0x2b, |
| EthTxStat1 = 0x2c, |
| EthRxStat = 0x2d, |
| WakeupControl = 0x78, |
| Reg7b = 0x7b, |
| Gpio0 = 0x7e, |
| Gpio1 = 0x7f, |
| Reg81 = 0x81, |
| }; |
| |
| |
| typedef struct pegasus { |
| struct usb_device *usb; |
| struct usb_interface *intf; |
| struct net_device *net; |
| struct net_device_stats stats; |
| struct mii_if_info mii; |
| unsigned flags; |
| unsigned features; |
| u32 msg_enable; |
| u32 wolopts; |
| int dev_index; |
| int intr_interval; |
| struct tasklet_struct rx_tl; |
| struct work_struct carrier_check; |
| struct urb *ctrl_urb, *rx_urb, *tx_urb, *intr_urb; |
| struct sk_buff *rx_pool[RX_SKBS]; |
| struct sk_buff *rx_skb; |
| struct usb_ctrlrequest dr; |
| wait_queue_head_t ctrl_wait; |
| spinlock_t rx_pool_lock; |
| int chip; |
| unsigned char intr_buff[8]; |
| __u8 tx_buff[PEGASUS_MTU]; |
| __u8 eth_regs[4]; |
| __u8 phy; |
| __u8 gpio_res; |
| } pegasus_t; |
| |
| |
| struct usb_eth_dev { |
| char *name; |
| __u16 vendor; |
| __u16 device; |
| __u32 private; /* LSB is gpio reset value */ |
| }; |
| |
| #define VENDOR_3COM 0x0506 |
| #define VENDOR_ABOCOM 0x07b8 |
| #define VENDOR_ACCTON 0x083a |
| #define VENDOR_ADMTEK 0x07a6 |
| #define VENDOR_AEILAB 0x3334 |
| #define VENDOR_ALLIEDTEL 0x07c9 |
| #define VENDOR_ATEN 0x0557 |
| #define VENDOR_BELKIN 0x050d |
| #define VENDOR_BILLIONTON 0x08dd |
| #define VENDOR_COMPAQ 0x049f |
| #define VENDOR_COREGA 0x07aa |
| #define VENDOR_DLINK 0x2001 |
| #define VENDOR_ELCON 0x0db7 |
| #define VENDOR_ELECOM 0x056e |
| #define VENDOR_ELSA 0x05cc |
| #define VENDOR_GIGABYTE 0x1044 |
| #define VENDOR_HAWKING 0x0e66 |
| #define VENDOR_HP 0x03f0 |
| #define VENDOR_IODATA 0x04bb |
| #define VENDOR_KINGSTON 0x0951 |
| #define VENDOR_LANEED 0x056e |
| #define VENDOR_LINKSYS 0x066b |
| #define VENDOR_LINKSYS2 0x077b |
| #define VENDOR_MELCO 0x0411 |
| #define VENDOR_MICROSOFT 0x045e |
| #define VENDOR_MOBILITY 0x1342 |
| #define VENDOR_NETGEAR 0x0846 |
| #define VENDOR_OCT 0x0b39 |
| #define VENDOR_SMARTBRIDGES 0x08d1 |
| #define VENDOR_SMC 0x0707 |
| #define VENDOR_SOHOWARE 0x15e8 |
| #define VENDOR_SIEMENS 0x067c |
| |
| |
| #else /* PEGASUS_DEV */ |
| |
| PEGASUS_DEV( "3Com USB Ethernet 3C460B", VENDOR_3COM, 0x4601, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "ATEN USB Ethernet UC-110T", VENDOR_ATEN, 0x2007, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "USB HPNA/Ethernet", VENDOR_ABOCOM, 0x110c, |
| DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA ) |
| PEGASUS_DEV( "USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4104, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4004, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4007, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x4102, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x4002, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x400b, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x400c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0xabc1, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x200c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Accton USB 10/100 Ethernet Adapter", VENDOR_ACCTON, 0x1046, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "SpeedStream USB 10/100 Ethernet", VENDOR_ACCTON, 0x5046, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Philips USB 10/100 Ethernet", VENDOR_ACCTON, 0xb004, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "ADMtek ADM8511 \"Pegasus II\" USB Ethernet", |
| VENDOR_ADMTEK, 0x8511, |
| DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA ) |
| PEGASUS_DEV( "ADMtek ADM8513 \"Pegasus II\" USB Ethernet", |
| VENDOR_ADMTEK, 0x8513, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "ADMtek ADM8515 \"Pegasus II\" USB-2.0 Ethernet", |
| VENDOR_ADMTEK, 0x8515, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "ADMtek AN986 \"Pegasus\" USB Ethernet (evaluation board)", |
| VENDOR_ADMTEK, 0x0986, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "AN986A USB MAC", VENDOR_ADMTEK, 1986, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "AEI USB Fast Ethernet Adapter", VENDOR_AEILAB, 0x1701, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Allied Telesyn Int. AT-USB100", VENDOR_ALLIEDTEL, 0xb100, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Belkin F5D5050 USB Ethernet", VENDOR_BELKIN, 0x0121, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Billionton USB-100", VENDOR_BILLIONTON, 0x0986, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Billionton USBLP-100", VENDOR_BILLIONTON, 0x0987, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "iPAQ Networking 10/100 USB", VENDOR_COMPAQ, 0x8511, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Billionton USBEL-100", VENDOR_BILLIONTON, 0x0988, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Billionton USBE-100", VENDOR_BILLIONTON, 0x8511, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Corega FEter USB-TX", VENDOR_COREGA, 0x0004, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Corega FEter USB-TXS", VENDOR_COREGA, 0x000d, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x4001, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x4002, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x4102, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x400b, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "D-Link DSB-650TX", VENDOR_DLINK, 0x200c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "D-Link DSB-650TX(PNA)", VENDOR_DLINK, 0x4003, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "D-Link DSB-650", VENDOR_DLINK, 0xabc1, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "GOLDPFEIL USB Adapter", VENDOR_ELCON, 0x0002, |
| DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA ) |
| PEGASUS_DEV( "ELECOM USB Ethernet LD-USB20", VENDOR_ELECOM, 0x4010, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "EasiDock Ethernet", VENDOR_MOBILITY, 0x0304, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Elsa Micolink USB2Ethernet", VENDOR_ELSA, 0x3000, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "GIGABYTE GN-BR402W Wireless Router", VENDOR_GIGABYTE, 0x8002, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Hawking UF100 10/100 Ethernet", VENDOR_HAWKING, 0x400c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "HP hn210c Ethernet USB", VENDOR_HP, 0x811c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "IO DATA USB ET/TX", VENDOR_IODATA, 0x0904, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "IO DATA USB ET/TX-S", VENDOR_IODATA, 0x0913, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Kingston KNU101TX Ethernet", VENDOR_KINGSTON, 0x000a, |
| DEFAULT_GPIO_RESET) |
| PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x4002, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "LANEED USB Ethernet LD-USBL/TX", VENDOR_LANEED, 0x4005, |
| DEFAULT_GPIO_RESET | PEGASUS_II) |
| PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x400b, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "LANEED USB Ethernet LD-USB/T", VENDOR_LANEED, 0xabc1, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x200c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Linksys USB10TX", VENDOR_LINKSYS, 0x2202, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Linksys USB100TX", VENDOR_LINKSYS, 0x2203, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Linksys USB100TX", VENDOR_LINKSYS, 0x2204, |
| DEFAULT_GPIO_RESET | HAS_HOME_PNA ) |
| PEGASUS_DEV( "Linksys USB10T Ethernet Adapter", VENDOR_LINKSYS, 0x2206, |
| DEFAULT_GPIO_RESET | PEGASUS_II) |
| PEGASUS_DEV( "Linksys USBVPN1", VENDOR_LINKSYS2, 0x08b4, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "Linksys USB USB100TX", VENDOR_LINKSYS, 0x400b, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Linksys USB10TX", VENDOR_LINKSYS, 0x200c, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "MELCO/BUFFALO LUA-TX", VENDOR_MELCO, 0x0001, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "MELCO/BUFFALO LUA-TX", VENDOR_MELCO, 0x0005, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "MELCO/BUFFALO LUA2-TX", VENDOR_MELCO, 0x0009, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "Microsoft MN-110", VENDOR_MICROSOFT, 0x007a, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "NETGEAR FA101", VENDOR_NETGEAR, 0x1020, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "OCT Inc.", VENDOR_OCT, 0x0109, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "OCT USB TO Ethernet", VENDOR_OCT, 0x0901, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "smartNIC 2 PnP Adapter", VENDOR_SMARTBRIDGES, 0x0003, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "SMC 202 USB Ethernet", VENDOR_SMC, 0x0200, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "SMC 2206 USB Ethernet", VENDOR_SMC, 0x0201, |
| DEFAULT_GPIO_RESET | PEGASUS_II) |
| PEGASUS_DEV( "SOHOware NUB100 Ethernet", VENDOR_SOHOWARE, 0x9100, |
| DEFAULT_GPIO_RESET ) |
| PEGASUS_DEV( "SOHOware NUB110 Ethernet", VENDOR_SOHOWARE, 0x9110, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| PEGASUS_DEV( "SpeedStream USB 10/100 Ethernet", VENDOR_SIEMENS, 0x1001, |
| DEFAULT_GPIO_RESET | PEGASUS_II ) |
| |
| |
| #endif /* PEGASUS_DEV */ |